Proposal for improving fishing opportunities off Pt. Loma by construction of an artificial reef

(Document pdf contains 42 pages)

Design and construction of portable surface aeration pump for tanks and small ponds

The maintenance of adequate dissolved oxygen level is very important in the economy of any aquaculture system. An easy to construct aerating device was created using 0.5 hp water-pump, shower rose, Styrofoam, and rubber hose. The aerator works by drawing water from below and discharging it into the atmosphere as a spray. The spray is aerated as it splashes into the water surface. The aerating device has an average spray of 1.2 unit and doubles the dissolved oxygen content of 37.8 m super(3) tank in one hour

Indigenous construction of fishing boats at Versova village in Maharashtra State

Versova, one of the 23 fishing villages in the district of Greater Bombay, is a major fishing centre. During the last three decades mechanisation of fishing boats received a tremendous boost in the state specially in and around Bombay resulting in higher income and gainful employment to fishermen. Indigenous construction of fishing boats at Versova contributes to the marine fisheries development. Inspite of certain constraints in construction activities, training of artisans in boat construction would ultimately help in the economic growth of the village.

The design and construction of flat rectangular otter boards for bottom trawling: a review

The design and construction of the otter board is a subject of great importance for economy in trawling. This review incorporates a historical resume tracing the change and development• of otter boards. The size of the otter board and its relationship with the horse power of the engine and size of the net and the methods of rigging are dealt with. The factors influencing the horizontal spread are discussed. The effect of the angles of attack, heel and tilt and the ground reaction on the force coefficients have been reviewed and discussed with particular reference to flat rectangular otter boards used for bottom trawling. A short account of other designs of otter boards used for improved efficiency is given. Suggestion for improving the efficacy of otter boards based on the work hitherto done has been made. The contributions relating to the various aspects of design and performance of trawl boards carried out till 1969 have been considered.

Utilization of treated wood, steel, fibreglass, ferrocement and aluminium in the construction of modern fishing boats and their comparative cost analysis

Modern fishing boats have to be built not only on perfect lines but also with sound and strong construction materials that will ensure a long lasting trouble free service commensurate with the heavy capital investment involved. Choice of construction materials for fishing boats need careful scrutiny as they have to perform too well under most aggressive environments-sea-water and marine atmosphere. A number of alternative boat-building materials are now available whose comparative merits and demerits as well as comparative costs are brought out in this paper.

Notes on the construction of 12 cu m ferrocement maturation tank for prawn broodstock

The study aimed to develop an economical, rational and easy method of constructing ferrocement tank suitable for P. monodon maturation.

Development of design and construction of fishing boats in Uganda

Fishing boats and canoes varied very little in Uganda from the middle of the 19th century umil 1949. types in use being the Dug Out Canoe. up to 40 ft. in length with 4 ft. beam hollowed from trees, and "Sesse" canoes which were used on Lake Victoria; these had an obvious Arab influence. The length of the "Sesse" in recent years as from about 1912 is 28 ft., and it is used as an open fishing craft.

Design and construction of a two dimensional duct equipped with a wave generator and a variable coastal slope and an ocean wave energy conversion system (OWC)

The aims of this thesis were evaluation the type of wave channel, wave current, and effect of some parameters on them and identification and comparison between types of wave maker in laboratory situations. In this study, designing and making of two dimension channels (flume) and wave maker for experiment son the marine buoy, marine building and energy conversion systems were also investigated. In current research, the physical relation between pump and pumpage and the designing of current making in flume were evaluated. The related calculation for steel building, channels beside glasses and also equations of wave maker plate movement, power of motor and absorb wave(co astal slope) were calculated. In continue of this study, the servo motor was designed and applied for moving of wave maker’s plate. One Ball Screw Leaner was used for having better movement mechanisms of equipment and convert of the around movement to linear movement. The Programmable Logic Controller (PLC) was also used for control of wave maker system. The studies were explained type of ocean energies and energy conversion systems. In another part of this research, the systems of energy resistance in special way of Oscillating Water Column (OWC) were explained and one sample model was designed and applied in hydrolic channel at the Sheikh Bahaii building in Azad University, Science and Research Branch. The dimensions of designed flume was considered at 16 1.98 0. 57 m which had ability to provide regular waves as well as irregular waves with little changing on the control system. The ability of making waves was evaluated in our designed channel and the results were showed that all of the calculation in designed flume was correct. The mean of error between our results and theory calculation was conducted 7%, which was showed the well result in this situation. With evaluating of designed OWC model and considering of changes in the some part of system, one bigger sample of this model can be used for designing the energy conversion system model. The obtained results showed that the best form for chamber in exit position of system, were zero degree (0) in angle for moving below part, forty and five (45) degree in front wall of system and the moving forward of front wall keep in two times of height of wave.

Environmental and social impact monitoring of the Bujagali Hydropower Project (BHPP), Uganda Fisheries Component: monthly patterns in physico-chemical conditions and fish catch in the immediate vicinity of the Bujagali Hydropower construction site, 29th September - 28th October 2007

Following the commencement of construction works of a 250 MW hydropower plant at Dumbbell Island in the Upper Victoria Nile in September 2007, BEL requested NaFIRRI to conduct continuous monitoring of fish catches at two transects i.e. the immediate upstream transect of the project site (Kalange-Makwanzi) and the immediate downstream .transect (Buyala-Kikubamutwe). The routine monitoring surveys were designed to be conducted twice a week at each of the tWo transects. It was anticipated that major immediate impacts were to occur during construction, and these needed to be known by BEL as part of a mitigation strategy. For example, the construction of it cofferdam could be accompanied by rapid changes in water quality and quantity downstream of the construction. These changes in turn could affect the fish catch and would probably be missed by the quarterly monitoring already in place. Therefore, a major cbjective of the more regular and rapid monitoring was to discern immediate impacts of construction activities by focusing on selected water quality parameters (total suspended solids, water conductivity, temperature, dissolved oxygen and pH) and fish catch characteristics (total catch, catch rates and value of the catch)