Investigations on wooden floating materials: the loss of buoyancy under continuous immersion in water and the rate of its redemption by drying

A wooden fishing float under immersion in water for long periods is liable to absorb water, the quantity of water absorbed possibly being dependent upon the physical factors like the specific gravity and the inherent property of the material, the time of soaking and the pressure acting on it. Consequently a wooden float is likely to become heavy and loss its original buoyancy. However, when the float is removed from water and dried, the lost buoyancy is regained on complete drying. The present paper is an attempt to elucidate these two important characteristics of some of the chief wooden floating materials used on the West Coast of India.

On the optimum buoyancy-weight relation for a bottom trawl

Comparative fishing operations were carried out with 0.55; 0.75 and 1.00 buoyancy-weight relations of bottom trawl in order to find out the optimum relation. Two nets, 18.26 m. (60') two seam nylon and 16.16 m. (23') two seam cotton trawls, were used for the experiment. The results showed that the total catch per trawling hour with 0.75 B-W relation was 16.5% and 32.08% more than that with 0.55 and 1.00 B-W relation for nylon net used. A similar trend was noticed with cotton trawl also as the catch rate with 0.75 B-W relation was 13.89% and 25.78% more than that with 0.55 and 1.00 B-W relations. However, the analysis of catch composition indicated that the off bottom fishes like lactarius, upenoides sp., synagris sp. etc., were of more percentage with 1.00 B-W relation, near bottom fish like saurida, sciaenids etc., were more with 0.75 B-W relation, while the bottom fishes like soles, prawns, skates and rays etc., were more with 0.55 B-W relation.

Guide to best practices for ocean CO2 measurements

CHAP 1 - Introduction to the Guide CHAP 2 - Solution chemistry of carbon dioxide in sea water CHAP 3 - Quality assurance CHAP 4 - Recommended standard operating procedures (SOPs) SOP 1 - Water sampling for the parameters of the oceanic carbon dioxide system SOP 2 - Determination of total dissolved inorganic carbon in sea water SOP 3a - Determination of total alkalinity in sea water using a closed-cell titration SOP 3b - Determination of total alkalinity in sea water using an open-cell titration SOP 4 - Determination of p(CO2) in air that is in equilibrium with a discrete sample of sea water SOP 5 - Determination of p(CO2) in air that is in equilibrium with a continuous stream of sea water SOP 6a - Determination of the pH of sea water using a glass/reference electrode cell SOP 6b - Determination of the pH of sea water using the indicator dye m-cresol purple SOP 7 - Determination of dissolved organic carbon and total dissolved nitrogen in sea water SOP 7 en Español - Determinacion de carbono organico disuelto y nitrogeno total disuelto en agua de mar SOP 11 - Gravimetric calibration of the volume of a gas loop using water SOP 12 - Gravimetric calibration of volume delivered using water SOP 13 - Gravimetric calibration of volume contained using water SOP 14 - Procedure for preparing sodium carbonate solutions for the calibration of coulometric CT measurements SOP 21 - Applying air buoyancy corrections SOP 22 - Preparation of control charts SOP 23 - Statistical techniques used in quality assessment SOP 24 - Calculation of the fugacity of carbon dioxide in the pure gas or in air CHAP 5 - Physical and thermodynamic data Errata - to the hard copy of the Guide to best practices for ocean CO2 measurements

Effect of Cattail (Typha domingensis) Extracts, Leachates, and Selected Phenolic Compounds on Rates of Oxygen Production by Salvinia (Salvinia minima)

Salvinia (Salvinia minima Willd.) is a water fern found in Florida waters, usually associated with Lemna and other small free-floating species. Due to its buoyancy and mat-forming abilities, it is spread by moving waters. In 1994, salvinia was reported to be present in 247 water bodies in the state (out of 451 surveyed public waters, Schardt 1997). It is a small, rapidly growing species that can become a nuisance due to its explosive growth rates and its ability to shade underwater life (Oliver 1993). Any efforts toward management of salvinia populations must consider that, in reasonable amounts, its presence is desirable since it plays an important role in the overall ecosystem balance. New management alternatives need to be explored besides the conventional herbicide treatments; for example, it has been shown that the growth of S. molesta can be inhibited by extracts of the tropical weed parthenium (Parthenium hysterophorus) and its purified toxin parthenin (Pande 1994, 1996). We believe that cattail, Typha spp. may be a candidate for control of S. minima infestations. Cattail is an aggressive aquatic plant, and has the ability to expand over areas that weren't previously occupied by other species (Gallardo et al. 1998a and references cited there). In South Florida, T. domingensis is a natural component of the Everglades ecosystem, but in many cases it has become the dominant marsh species, outcompeting other native plants. In Florida public waters, this cattail species is the most dominant emergent species of aquatic plants (Schardt 1997). Several factors enable it to accomplish opportunistic expansion, including size, growth habits, adaptability to changes in the surroundings, and the release of compounds that can prevent the growth and development of other species. We have been concerned in the past with the inhibitory effects of the T. domingensis extracts, and the phenolic compounds mentioned before, towards the growth and propagation of S. minima (Gallardo et al. 1998b). This investigation deals with the impact of cattail materials on the rates of oxygen production of salvinia, as determined through a series of Warburg experiments (Martin et al. 1987, Prindle and Martin 1996).

Temporal and spatial changes in milfoil distribution and biomass associated with weevils in Fish Lake, WI

During the course of an eight year monitoring effort, the Wisconsin Department of Natural Resources documented a significant decline in milfoil biomass and distribution in Fish Lake, Wisconsin. Average milfoil biomass declined by 40- 50% from 374-524 g dw m -2 during 1991-93 to 265 g dw m -2 during both 1994 and 1995. Milfoil recovered fully in 1996- 98 to 446- 564 g dw m -2 . The size of the milfoil bed, as discerned from aerial photographs, shrank from a maximum coverage of 40 ha in 1991 to less than 20 ha during 1995. During the “crash” of 1994-95, milfoil plants exhibited typical signs of weevil-induced damage, including darkened, brittle, hollowed-out growing tips, and the arching and collapse of stems associated with loss of buoyancy. Monitoring of weevils and stem damage during 1995-98 showed highest densities and heaviest damage occurred near shore and subsequently fanned out into deeper water from core infestation sites each spring. The extent of milfoil stem damage was positively correlated with weevil densities (monthly sampling). However, weevil densities and stem damage were lower during 1995 (when milfoil biomass was in decline) than during 1996-98 (when milfoil biomass was fully recovered).

Technological status and development prospects of small-scale fishing crafts in Nigerian coastal water

A study of fishing crafts was conducted in some coastal states of Nigeria to elucidate findings on the existing crafts as the baseline for further developments. Based on the technical designs, three types of fishing crafts were identified; planked, dug-out and half dug-out canoes. The planked canoes have the largest cubic number and dug-out canoes the least. At loadwater line, the ratio of freeboard to draft was 2 : 1 for planked canoes, indicating reserved buoyancy. Trim of planked canoe is by stern; the beam-length ratio for dug-out canoes showed high drag. Most of the sea-going canoes have U-shaped bottom hull profile capable of withstanding the rigours of surf landing and displayed good stability against longitudinal water wave. Gunwale and thwarts provided respectively the longitudinal and transverse strength of planked and half dug-out canoes. With its characteristics 'weight low down' construction, planked canoe represent the climax of small scale fishing crafts developments in Nigerian coastal waters. It's only draw back is durability. Further improvement in this canoe should be aimed at increasing the hull size and stiffness, water tightness of deck by coating, caulking, fastening, increasing level of motorization and installation of deck working equipments. Experimental design and use of fibre glass, aluminium and ferrocement hulls, together with improved planked canoe is highly advocated

Wassertiefenabhängige Auftriebsschwerpunktregelung für seitlich versetzt geschleppte Schwingerträger

The noise emission of the vessel, especially in shallow waters, causes a fright reaction of the fishes near the vessel. To reduce the uncertainty of hydroacoustic measurements connected with that fact, a side shifted towed body is used for the hydroacoustic stock estimation in the Baltic sea. If the towed body was running close to the surface it was quite sensitive to waves. To make the running properties of the side shifted towed body more robust a control of the center of buoyancy depending on the diving depth was introduced. The goal was set to control the towed body without additional energy supply. First results are shown.

Experimente über die Wirkung von UV-B auf pelagische Fischembryonen in einem Sonnenscheinsimulator

One of the supposed effects of the observed ozone depletion is the increase of solar UV-B irradiation at the seasurface. This will cause an impact on certain compartments of marine ecosystems. Especially, sensitive developmental stages of pelagic fish embryos might be affected. Embryos of dab (Limanda limanda) and plaice (Pleuronectes plalessa) were experimentally exposed 10 different amounts of UVB irradiation in a sunshine simulator. This programmable device allows the dosage of realistic solar irradiation in quality and guantity. Experiments were carried out in March 1995 and February 1996. Either artificially inserninated and reared emhryos of dab and plaice or embryos caught in the German Bight were exposed to simulated solar irradiation. The 1995 experiments served to identify the effective irradiation dosages. For the 1996 experiments irradiation applied was much lower, being dose to realistic valucs expected over the North Sea as a consequence of ozone depletion. The following end points were studied: 1. Mortality, 2. sublethal morphological effects (malformations), 3. DNA damage, 4. changes in buoyancy of embryos measured as changes in osmolarity of the perivitelline fluid. Conditions for the simulation of daylight were a c1oudless sky with a solar zenith distance of 34 % (air mass 1.2). The adopted ozone depletion was 40 % corresponding to 180 DU (Dobson Units) instead of 300 DU. In the 1995 experiments time and dosage dependent influenccs on mortality and buoyancy of embryos of dab and plaice were found. Even in those embryos which were protected from the UV-B spectral range a loss of buoyancy was registered after 12 hours in the simulator. No diffcrences in DNA integrity as determined by DNA unwinding of exposed and control embryos were found. Also with lower amounts of irradiation in the 1996 experiments dosage dependent acute mortality, malformations, and impact on the buoyancy of the emhryos was registered. Sublethal effects occurred as well in embryos protected against UV-B in the exposure chambers, but were not found in the dark controls. The impact of low dosages of UV-B on the buoyancy of pelagic fish embryos might indicate an important ecological threat and deserves further studies.

The ecology of phytoplankton in Shropshire and Cheshire meres

This review summarizes the findings of 5 years' research (June 1970-June 1975) on the meres of the Shropshire-Cheshire Plain. A mere is a small, shallow lake; supplied principally by ground water, whose chemical composition is infkuenced by the glacial frift through which it is percolating. The seasonal periodicity of the phytoplankton in the meres involved work mainly in the Grose Mere. Here diatoms were typically dominant in Feb & March, green algae in April & May, blue-green algae in early summer and dinoflagellates in late summer. This pattern is broadly similar from year to year, and has been suggested to be representative of a 'regional type'; it is also similar to that described for many of the world's mildly eutrophic temperate lakes. Vertical distribution of phytoplankton is influenced by their buoyancy (or lack of it) of by their ability to swim. A stylized depth-time distribution of 4 major phytoplankton components in Crose Mere is given diagrammatically.

Quantification of drag and lift imposed by pop-up satellite archival tags and estimation of the metabolic cost to cownose rays (Rhinoptera bonasus)

The recent development of the pop-up satellite archival tag (PSAT) has allowed the collection of information on a tagged animal, such as geolocation, pressure (depth), and ambient water temperature. The success of early studies, where PSATs were used on pelagic fishes, has spurred increasing interest in the use of these tags on a large variety of species and age groups. However, some species and age groups may not be suitable candidates for carrying a PSAT because of the relatively large size of the tag and the consequent energy cost to the study animal. We examined potential energetic costs to carrying a tag for the cownose ray (Rhinoptera bonasus). Two forces act on an animal tagged with a PSAT: lift from the PSATs buoyancy and drag as the tag is moved through the water column. In a freshwater flume, a spring scale measured the total force exerted by a PSAT at flume velocities from 0.00 to 0.60 m/s. By measuring the angle of deflection of the PSAT at each velocity, we separated total force into its constituent forces — lift and drag. The power required to carry a PSAT horizontally through the water was then calculated from the drag force and velocity. Using published metabolic rates, we calculated the power for a ray of a given size to swim at a specified velocity (i.e., its swimming power). For each velocity, the power required to carry a PSAT was compared to the swimming power expressed as a percentage, %TAX (Tag Altered eXertion). A %TAX greater than 5% was felt to be energetically significant. Our analysis indicated that a ray larger than 14.8 kg can carry a PSAT without exceeding this criterion. This method of estimating swimming power can be applied to other species and would allow a researcher to decide the suitability of a given study animal for tagging with a PSAT.

Characterizing a cyanobacterial bloom in western Lake Erie using satellite imagery and meteorological data

The distribution and intensity of a bloom of the toxic cyanobacterium, Microcystis aeruginosa, in western Lake Erie was characterized using a combination of satellite ocean-color imagery, field data, and meteorological observations. The bloom was first identified by satellite on 14 August 2008 and persisted for more than 2 months. The distribution and intensity of the bloom was estimated using a satellite algorithm that is sensitive to near-surface concentrations of M. aeruginosa. Increases in both area and intensity were most pronounced for wind stress less than 0.05 Pa. Area increased while intensity did not change for wind stresses of 0.05–0.1 Pa, and both decreased for wind stress greater than 0.1 Pa. The recovery in intensity at the surface after strong wind events indicated that high wind stress mixed the bloom through the water column and that it returned to the surface once mixing stopped. This interaction is consistent with the understanding of the buoyancy of these blooms. Cloud cover (reduced light) may have a weak influence on intensity during calm conditions. While water temperature remained greater than 15°C, the bloom intensified if there were calm conditions. For water temperature less than 15°C, the bloom subsided under similar conditions. As a result, wind stress needs to be considered when interpreting satellite imagery of these blooms.

Trends in development in the prawn fishing technique in India: a review

The paper provides some background information about the developments in the prawn fishing technique. The important indigenous gear for prawns are the filtering type nets like the stake nets, boat seines and beach seines with bag. The only indigenous net, which can be compared in design with the modern bottom trawling gear, is the "Thuri Valai" of the Madras Coast. Prawns have also been reported from the catches of gill nets and cast nets. Dredges and beam trawls are simplest among the dragged gear. Even though several earlier attempts were made with the beam trawl, in 1959 season a detailed experiment was made to study the fishing features of this gear. The subsequent experiments conducted were for comparison with otter trawl, towing of 2 beam trawls one behind the other and the use of tickler chain. The initial experiments with otter trawls were mainly directed towards operational aspects. The experiments were to evaluate the effectiveness of fully mechanised and partially mechanised operation, the effect of extra buoyancy of floats and the use of tickler chain. Subsequent developments had been on the structure and design of prawn trawling gear. Effect of long wings and sweeps were tested. Catches of nylon and cotton nets were compared. The sizes of meshes of the cod-end have also been increased.

Three dimensional modeling of contaminants transportation (oil spill) in Caspian Sea

Nowadays, Caspian Sea is in focus of more attentions than past because of its individualistic as the biggest lake in the world and the existing of very large oil and gas resources within it. Very large scale of oil pollution caused by development of oil exploration and excavation activities not only make problem for coastal facilities but also make severe damage on environment. In the first stage of this research, the location and quality of oil resources in offshore and onshore have been determined and then affected depletion factors on oil spill such as evaporation, emulsification, dissolution, sedimentation and so on have been studied. In second stage, sea hydrodynamics model is offered and tested by determination of governing hydrodynamic equations on sea currents and on pollution transportation in sea surface and by finding out main parameters in these equations such as Coriolis, bottom friction, wind and etc. this model has been calculated by using cell vertex finite volume method in an unstructured mesh domain. According to checked model; sea currents of Caspian Sea in different seasons of the year have been determined and in final stage different scenarios of oil spill movement in Caspian sea on various conditions have been investigated by modeling of three dimensional oil spill movement on surface (affected by sea currents) and on depth (affected by buoyancy, drag and gravity forces) by applying main above mentioned depletion factors.

Microstructures layering, mechanisms in the middle waters of the Persian Gulf

Layered structures, known as micro structures in marine environments are common features of which their formation mechanisms are first reviewed. Some methods of measuring such features based on the measurements and theories are presented for the Persian Gulf. This includes determination of layers with temperature inversion (TI) associated with double diffusive convection (DDC). The relevant associated parameters are estimated from ROPME CTD data for late winter and early summer of 1992. Only in certain parts temperature inversion and DDC are observed which seem to produce layered structures. Observations show that the places with TI and DDC are mainly confined to the frontal regions where the water entering the Persian Gulf and water exiting it meet, nearly along the axis of the Gulf. TI and DDC is mainly observer in the northern bound of the front. Typical density ratio for regions with TI and DDC is 0.7 to 0.2 and the mean depth is at about 37 ± 3 m for the Persian Gulf. TI and DDC are also found in the outflow from the Persian Gulf to the Oman Gulf which is found to be at a depth of about 250 m. Horizontal addiction and reduction of solar heating seem to be the main reasons in producing layers with TI and DDC. It is also found that the regime of DDC in the Persian Gulf is more diffusive and the flow associated with intrusion layers with TI is non-isopycnal (more unstable). However for the Oman sea both diffusive and finger regime are observed and the flow is inferred to be isopycnal (more stable statically). Typical heat and salt fluxes due to DDC are found to be 6 W/m2 and 0.36 W/m2 respectively. Effective salinity diffusivity, Ks and heat diffusivity, Kr have been estimated for the places with DDC in the Persian Gulf and Oman Gulf (Ks=1.1 *10-7 m2/s, KT= 1.88*10-6 m2/s). Their values are within the values obtained by others. The buoyancy frequency for the Persian Gulf with typical mean value of 0.05s-1 is much higher than these of the free Oceans. Such large values of N (typically 0.05 s-1) indicate that processes such as tide can produce strong internal waves which may be another factor in producing layered structures. This requires separate study.

Three dimensional numerical simulation of thermohaline currents of the Persian Gulf

Observational data and a three dimensional numerical model (POM) are used to investigate the Persian Gulf outflow structure and its spreading pathway into the Oman Sea. The model is based on orthogonal curvilinear coordinate system in horizontal and train following coordinate (sigma coordinate) system in vertical. In the simulation, the horizontal diffusivity coefficients are calculated form Smogorinsky diffusivity formula and the eddy vertical diffusivities are obtained from a second turbulence closure model (namely Mellor-Yamada level 2.5 model of turbulence). The modeling area includes the east of the Persian Gulf, the Oman Sea and a part of the north-east of the Indian Ocean. In the model, the horizontal grid spacing was assumed to be about 3.5 km and the number of vertical levels was set to 32. The simulations show that the mean salinity of the PG outflow does not change substantially during the year and is about 39 psu, while its temperature exhibits seasonal variations. These lead to variations in outflow density in a way that is has its maximum density in late winter (March) and its minimum in mid-summer (August). At the entrance to the Oman Sea, the PG outflow turns to the right due to Coriolis Effect and falls down on the continental slope until it gains its equilibrium depth. The highest density of the outflow during March causes it to sink more into the deeper depths in contrast to that of August which the density is the lowest one. Hence, the neutral buoyancy depths of the outflow are about 500 m and 250 m for March and August respectively. Then, the outflow spreads in its equilibrium depths in the Oman Sea in vicinity of western and southern boundaries until it approach the Ras al Hamra Cape where the water depth suddenly begins to increase. Therefore, during March, the outflow that is deeper and wider relative to August, is more affected by the steep slope topography and as a result of vortex stretching mechanism and conservation of potential vorticity it separates from the lateral boundaries and finally forms an anti-cyclonic eddy in the Oman Sea. But during August the outflow moves as before in vicinity of lateral boundaries. In addition, the interaction of the PG outflow with tide in the Strait of Hormuz leads to intermittency in outflow movement into the Oman Sea and it could be the major reason for generations of Peddy (Peddies) in the Oman Sea.