Analyse der Beifangreduktion durch Gitternetze in der kommerziellen Garnelenfischerei

Trials for the determination of the magnitude of bycatch reduction by sorting grids used in the commercial brown shrimp fishery were carried out from September to December 1997. Trawls with 9 m beam length were used on different fishing grounds in the estuary of the Elbe River near Cuxhaven. The sorting grids tested were made of stainless steel bars spaced at 18, 20, 22, 26 and 30 mm, built into a cylindrical stainless steel frame with a diameter of 65 cm at an angle of attack of 45 degrees. This frame was positioned between the forenet and codend. Simultaneous hauls were made with a trawl of equal construction but without a sorting grid, and the weighed catch components (fish, discard shrimps and commercial size shrimps) separated by means of a riddle were compared. The composition of the sorted out part of the catch of the sorting grid net could be calculated by comparise the corresponding catch components in both the standard trawl and the sorting grid trawl. According to this the total catch of the beam trawl with the sorting grid is reduced by 18 to 38 % depending on the space between the bars. 7 to 31 % of the sorted out part of the catch consists of fish. The use of the sorting grid, however, also leads to losses of 4 to 12 % in Oktober. Per hour of towing this means a loss of 10,3 % commerical size shrimps with a sorting grid of 18 mm space between the bars and of 12,4 % for a 26 mm grid.

Erster Einsatz von Trenngittern in der kommerziellen Garnelenfischerei

Comparative fishing trials were conducted in the river Elbe estuary using 9 m commercial brown shrimp beam trawls. To avoid the bycatch of fish a metal sorting grid of the Nordmöre type was used. The elliptical grid was constructed of 6 mm stainless steel bar with a spacing of 20 mm between the bars and housed in a cylindrical frame of 800 mm diameter. It was installed in the extension piece just in front of the codend. The inclination of the grid was 45 degrees. A fish outlet was provided in the upper panel of the trawl at the upper edge of the grid. A series of 8 tows of 15 min duration at a towing speed of 3 kns was done. For evaluation the catch of the main codend was compared to the portion of the catch escaped through the grid. The presence of the grid caused a 97.4 % reduction of the catch of lump sucker, a 90.6 % reduction of the catch of sea scorpion, a 79.3 % reduction of the catch of cod, a 58.8 % reduction of the catch of armed bullhead, a 39.6 % reduction of the catch of dab, a 34.7 % reduction of the catch of flounder, a 32.3 % reduction of the catch of smelt, a 19.8 % reduction of the catch of plaice and a 14.5 % reduction of the catch of brown shrimp.

Trenngitter - eine Alternative zu den Trichternetzen in der Garnelenfischerei

Experimental fishing trials were conducted in the Elbe Estuary using an experimental 3 m-standard beamtrawl. To avoid the by-catch of fish, a sorting grid was used. The elliptical grid was constructed of 6 mm diameter stainless steel bars with a spacing of 13 mm between the bars and housed in a cylindrical frame of 400 mm diameter. It was installed in the extension piece just in front of the codend angled at 45°, with a fish outlet at the top. A series of 10 tows of 15 minutes duration at a towing speed of 3 kn was done. The catch of the main codend was compared with the catch separated by the sorting grid. This achieved a reduction of 56 % of plaice (Pleuronectes platessa), 75 % of flounder (Platichthys flesus), 99 % of whiting (Merlangius merlangus), 94 % of cod (Gadus morhua) and 49 % of smelt (Osmerus eperlanus) with a mean loss of 43 % of shrimps (Crangon crangon). English grid trials in the Humber estuary using a flapper set or guiding funnel in front of the sorting grid device demonstrated reasonable lower escapement rates for fish and shrimps.

Design for Survival: Sustainability for Planet and Structure

Buildings in Port Aransas encounter drastic environmental challenges: the potential catastrophic storm surge and high winds from a hurricane, and daily conditions hostile to buildings, vehicles, and even most vegetation. Its location a few hundred feet from the Gulf of Mexico and near-tropical latitude expose buildings to continuous high humidity, winds laden with scouring sand and corrosive salt, and extremes of temperature and ultraviolet light. Building construction methods are able to address each of these, but doing so in a sustainable way creates significant challenges. The new research building at the Marine Science Institute has been designed and is being constructed to meet the demand for both survivability and sustainability. It is tracking towards formal certification as a LEED Gold structure while being robust and resistant to the harsh coastal environment. The effects of a hurricane are mitigated by elevating buildings and providing a windproof envelope. Ground-level enclosures are designed to be sacrificial and non-structural so they can wash or blow away without imposing damage on the upper portions of the building, and only non-critical functions and equipment will be supported within them. Design features that integrate survivability with sustainability include: orientation of building axis; integral shading from direct summer sunlight; light wells; photovoltaic arrays; collection of rainwater and air conditioning condensate for use in landscape irrigation; reduced impervious cover; xeriscaping and indigenous plants; recycling of waste heat from air conditioning systems; roofing system that reflects light and heat; long life, low maintenance stainless steel, high-tensile vinyl, hard-anodized aluminum and hot-dipped galvanized mountings throughout; chloride-resistant concrete; reduced visual impact; recycling of construction materials.

On the troll line investigations off Cochin during five fishing seasons. Pt. 2. Investigations during 1963-64 season

During this season the investigations were mainly directed towards elucidation of the selective action of trolling lures. Feather jigs, buffalo horn jigs, stainless steel jigs, Japanese whale bone jigs and plastic jigs were selected. Operations were carried out from Fisheries technology No. 5.