Leistungsmessung an Bord von Fischereifahrzeugen zur Kontrolle der 300-PS-Begrenzung in der Schollenbox

For monitoring of the engine power of fishing vessels permitted for fishery in the plaice box with engine power of 300 HP or less at sea three different portable power measurement systems are developed and tested. A system measuring the twist of the propeller shaft by two divisible gearwheels mounted on the shaft worked well at shafts with roller bearing at both sides of the measured interval of 100–300 mm length. Only at a very few fishing vessels this system is applicable and therefore for monitoring purposes not suitable. The application of a commercial available system measuring the stress at the surface of the shaft was simplified for application by non experts. The torque is measured by strain gauges. The calibration of the system, measuring and recording of the power is done by a PC automatically. A small polished facet on the shaft protected against oxidation is needed for easy and quick application. In this case the system can be used by technical personnel of supervision boats for monitoring of the engine power at sea in a short time. A third power measurement system determinates the torque by measuring the displacement of two supports clamped on the shaft at a distance of 100 mm. The displacement is measured by a micrometer gauge mounted on one of the supports. Readout of the rotating gauge display is possible taking advantage of stroboscopic effect. The system needs no conditioning of the shaft and can be used by non technicians. The development is not finished until now and some additional investigations and tests are required. Additional measures for monitoring of the power on fishing vessels by self recording power measurement systems and sealed fuel racks with limited injection are reported and discussed.

Plankton associated with medusae of the freshwater jellyfish Craspedacusta sowerbyi (Lankester) in a Thames backwater

Samples of plankton were taken from Broom Water in August 1997 after a sighting of medusae on 11th August. Broom Water is about 8 m wide, and extends 250 m from the main channel of the Thames, above the weir at Teddington. On 11th August medusae were so abundant that it was possible to collect 20 in ten minutes. They were rising to the surface in bright sunlight, then sinking slowly down through the water. Examination of a medusa's tentacles under a microscope revealed the presence of a commensal protozoan, a ciliate Trichodina pediculus. Over 20 species of phytoplankton were found in Broom Water. Most of the species are common and widespread, but it was a surprise to find Errerella bornhemiensis with its characteristic pyramidal colonies, which is a relatively rare species. Zooplankters in Broom Water consisted of Rotifera and Crustacea. Zooplankton is the main food of Craspedacusta and it was found that the crustaceans but not the rotifers did undergo significant changes during the period 11-19th August. The major changes were a big increase in the percentage of cyclopoids, and a marked decrease in Bosmina. This could be because the delicate cuticle of Bosmina is much more susceptible to the stinging cells of the medusae compared with the tougher exoskeleton of the cyclopoid.

The Cynthia Woods incident: When the rescuer becomes the rescuee

Survival at sea for Steven Conway and five Texas A&M University at Galveston students after the sinking of the sailboat Cynthia Woods.

Indigenous substitutes for "Lignum vitae" for making stern bearings for fishing boats

Difficulties are very often encountered in selecting proper material for making stern bearings for fishing boats. Conventional materials such as white metal, bronze etc. wear out too fast also causing considerable wear to the propeller shaft. Lignum-vitae, a natural wood commonly used for this purpose, is not available on a commercial scale in our country. Results of trials carried out to find out suitable substitutes for lignum-vitae from among indigenous timbers are presented in this paper.

Development of a torque meter for fishing vessels

The paper describes the development of an electronic instrument to measure the torque developed on the propeller shaft of fishing vessels at various speeds of the propeller. By measuring the torque, it is possible to determine the actual power transmitted from the engine gear-box unit to the propeller so that propeller efficiency can be evaluated and the optimum size of the propeller for a specific engine and vessel can be determined.

Use of fermented kitchen waste in rearing Penaeus monodon larvae

Fermented vegetable and kitchen wastes are available as feeds for not only zoea but also mysis and up to certain points in the postlarval stages of sugpo, Penaeus monodon. It is recommended that the hatchery use fermented wastes as larval feed for P.monodon when diatoms or brine shrimp nauplii are lacking or in short supply. Among three stages namely, zoea, mysis and postlarva, the survival rate during postlarva particularly after P SUB-4 was quite low. The problems encountered are as follows: (a) how to prevent fermented particles from lumping, (b) how to prevent them from easily sinking to the bottom, and, (c) how to prevent bacteria and fungi, particularly Lagenidium sp blooming.

Culturing the African lungfish in Uganda: effects of exogenous fish feed on growth performance in tanks

The availability of African lungfish (Protopterus aethiopicus) in many communities in Uganda is declining. Indigenous efforts to culture this fish usually produce poor yields and depend on feeding fish fry, minced meat, and leftover food. This study evaluates three formulated diets (diet-1, diet-2, diet-3) fed to wild caught lungfish fingerlings reared in indoor tanks for 77 days. Experimental fish gradually accepted sinking pellets, and marginal increases in average body weight were observed. Mean (± SE) final weight (15.86 ± 0.80 g) for fish fed on diet-3 was significantly higher (p < 0.05) than fish fed diet-1 and diet-2. Specific growth rates (SGR) for diet- 3 were significantly higher (p < 0.05) than diet-1, and marginally more than diet-2 (0.37 ± 0.04 %/ d). Feed conversions were similar (p >0.05), ranging from 1.61 ± 0.26 to 2.07 ± 0.11. Survivals after an 11-week culture were relatively low (< 60%), but generally increased (R2 = 0.667, P = 0.007) with increasing dietary proteins. Diet-3 had a significant higher survival rate (p< 0.05) than diet-1 and diet-2. Significant growth performance was attained with diet-3. This study demonstrated that sinking fish feed pellets can be used to culture wild-caught African fingerlings in captivity.