The use and economic benefits of fibres from sisal hemp (Agave sisalana) leaves as supporting ropes for fishing gear

Sisal hemp (Agave sisalana) leaves were harvested and processed using the beating and decomposition methods. The fibres obtained were washed, dried and finally spurned in to cordage of about 4mm diameter 39 pieces of ropes, each measuring 2 meters were altogether spurned. 30 pieces of these ropes were immersed in water for a period of 24 weeks, 6 were placed in a shaded and airily place and 3 were used for the head and footling of gillnet, sinker line of cast net and the main line of long line. Every other week, the ropes in water and air were tested for its breaking strength using an improved 50kg spring balance. At the end of the experiment, it was found the immersed ropes maintained a tensile strength of over 50kg/F for the first 18 weeks, thereafter; there was a gradual weekly reduction in the strength until the 23rd week when the tensile strength was less than 1kg/F. The cost benefit analysis showed that about 5,3146 tons processed fibers could be obtained fro 1ha. capable of being spenced in to 528300m of 4mm diameter cordage. This paper finally recommended the growth of sisal hemp plants by fisher folks so that there will be constant stock for intermittent harvesting for rope spurning

Preparation of acetate peels of valves from the ocean quahog, Arctica islandica, for age determinations

Techniques are described for preparing acetate peels of sectioned valves of ocean quahogs, Arctica islandica, for age determinations. The respective sequence of preparation begins by sectioning left valves oriented to include a single hinge tooth, bleaching to remove the heavy periostracum, embedding the valves in an epoxy resin, grinding and polishing the embedments to a high luster, etching the exposed cut valve surfaces, and applying sheet acetate with acetone. Annuli are clearly defined relative to growth increments in the peel preparations for all sizes and ages of ocean quahogs. (PDF file contains12 pages.)

Marketing of fishing gear materials and fishing gear making in parts of Kainji Lake basin

The importance of fishing gear in fishing cannot be over-emphasized; as without it fish cannot be obtained. The method used to catch fish affects the condition in which the product is landed. This means that a bad-catching method would produced bad fish to the consumer. To achieve the goal of self-sufficiency in fish production in Nigeria, there is need to address the lingering problems of fishing gear and craft technology, especially in terms of availability of materials and their cost. The sale and making of fishing gear materials are two areas of fisheries, which are yet to be exploited by the general public as forms of businesses for livelihood. The study is conducted in villages around the lower part of Kainji Lake, towards the dam, including New Bussa. It reveals that only the fishermen themselves are involved in making their own fishing gears while those involved in the selling of fishing gear materials like the sheet netting, ropes, twines, floats, sinkers etc are business men and women who may not have any experience of fishing. Also considered in the study is the art of making fishing crafts like the canoe and gourd. Very few entrepreneurs are involved and they are so skilled that each is specialized in the making of only one kind of craft or gear

Catches in ghost-fishing octopus and fish traps in the northeastern Atlantic Ocean (Algarve, Portugal)

Ghost fishing is the term used to describe the continued capture of fish and other living organisms after a fisherman has lost all control over the gear. Traps may be lost for a variety of reasons including theft, vandalism, abandonment, interactions with other gear, fouling on the bottom (i.e., traps and ropes are caught on rocky substrate), bad weather, and human error (Laist, 1995). Annual trap loss can be as high as 20% to 50% of fished traps in some fisheries (Al-Masroori et al., 2004). Because lost traps can continue to fish for long periods, albeit with decreasing efficiency over time (e.g., Smolowitz, 1978; Breen, 1987, 1990; Guillory, 1993), ghost fishing is a concern in fisheries worldwide.

Evaluation of a Pound Net Leader Designed to Reduce Sea Turtle Bycatch

Offshore pound net leaders in the southern portion of Chesapeake Bay in Virginia waters were documented to incidentally take protected loggerhead, Caretta caretta, and Kemp’s ridley, Lepidochelys kempii, sea turtles. Because of these losses, NOAA’s National Marine Fisheries Service (NMFS) in 2004 closed the area to offshore pound net leaders annually from 6 May to 15 July and initiated a study of an experimental leader design that replaced the top two-thirds of the traditional mesh panel leader with vertical ropes (0.95 cm) spaced 61 cm apart. This experimental leader was tested on four pound net sites on the eastern shore of Chesapeake Bay in 2004 and 2005. During the 2 trial periods, 21 loggerhead and Kemp’s ridley sea turtles were found interacting with the control leader and 1 leatherback turtle, Dermochelys coriacea, was found interacting with the experimental leader. Results of a negative binomial regression analysis comparing the two leader designs found the experimental leader significantly reduced sea turtle interactions (p=0.03). Finfish were sampled from the pound nets in the study to assess finfish catch performance differences between the two leader designs. Although the conclusions from this element of the experiment are not robust, paired t-test and Wilcoxon signed rank test results determined no significant harvest weight difference between the two leaders. Kolmogorov-Smirnov tests did not reveal any substantive size selectivity differences between the two leaders.

Import substitution of combination wire rope. Part 1. Design, production and evaluation of a prototype combination wire rope

Model combination wire ropes with different covering materials were prepared and worked out specification for the prototype. A table model hand operated wire rope twisting machine was also developed for this. Prototype combination wire rope was twisted in collaboration with M/s South India Wire Ropes Ltd., Alwaye. Specification details, properties and field performance of the prototype studied are reported.

Import substitution of combination wire rope. Part 2. Production and standardisation of 17 mm dia combination wire rope.

The prototype combination wire rope (Cift-CWR 1) developed for deep sea trawling was further studied for improvement, optimisation of efficiency and standardization. A series of improved prototype combination wire ropes (Cift-CWR 2 to 6) were twisted and evaluated their mechanical properties and reported in this paper with recommendations for a standard 17mm dia combination wire rope of 6S (7C+8+1 Scr) + 6 Crs(6+1+1 Crc) construction.

Import substitution of combination wire rope. Part 3: Comparison of standard Cift-CWR and imported combination wire rope

Tensile and extension properties of standard Cift-CWR and imported combination wire ropes from Japan, Norway and Denmark are studied and the analysis is presented in the paper. Tensile and chemical properties of steel wire, tensile and abrasive properties of PP covering, effect of twist on material at different stages are worked out and reported.