Tensile strength properties of polyethylene netting twines under exposure to out-door and artificial UV radiation

Photodegradation of three types of polyethylene twines namely, polyethylene fibrillated tape twine, polyethylene flat tape twine and polyethylene monofilament twines were studied by exposing them to sunlight and artificial UV radiation. The percentage residual strength varied in the samples, the monofilament with the highest residual strength followed by fibrillated tape twine and flat tape twine. A plot of the difference between the breaking strengths of the fibrillated tape twine and the mono filament twines against any given period of exposure exhibited a linear relationship

Configurations and relative efficiencies of shrimp trawls employed in southeastern United States waters

Common shrimp trawl designs employed in the southeastern United States shrimp fishery are the flat, balloon, semiballoon, jib, and super X-3. Recent innovations in trawl design and rigging, including the twin trawl rigging and tongue trawl design, have improved the efficiency of shrimp trawling gear. A description of the construction techniques for the different designs indicate differences which affect gear performance. Measurements of horizontal spread and vertical opening for 76 trawl configurations indicate the relative efficiencies of the different designs. Maximum horizontal spreading efficiency was achieved by the "twin" and "tongue" trawl designs followed by the super X-3, jib, balloon, and semiballoon designs. Designs having the greatest vertical openings were the tongue and flat trawl designs followed by the semiballoon. Maximum total gape dimension was demonstrated by the "Mongoose" tongue trawl. Comparison of trawl spreading efficiency and door area to headrope length ratio indicates that a range of 70-80 in square (per door) of door area is required for each foot of trawl headrope length for maximum efficiency with conventional trawl designs and 66-75 in square per foot of headrope for tongue trawl designs. (PDF file contains 18 pages.)

Variation in trawl geometry due to unequal warp length

Survey standardization procedures can reduce the variability in trawl catch efficiency thus producing more precise estimates of biomass. One such procedure, towing with equal amounts of trawl warp on both sides of the net, was experimentally investigated for its importance in determining optimal trawl geometry and for evaluating the effectiveness of the recent National Oceanic and Atmospheric Administration (NOAA) national protocol on accurate measurement of trawl warps. This recent standard for measuring warp length requires that the difference between warp lengths can be no more than 4% of the distance between the otter doors measured along the bridles and footrope. Trawl performance data from repetitive towing with warp differentials of 0, 3, 5, 7, 9, 11, and 20 m were analyzed for their effect on three determinants of flatfish catch efficiency: footrope distance off-bottom, bridle length in contact with the bottom, and area swept by the net. Our results indicated that the distortion of the trawl caused by asymmetry in trawl warp length could have a negative inf luence on flatfish catch efficiency. At a difference of 7 m in warp length, the NOAA 4% threshold value for the 83112 Eastern survey trawl used in our study, we found no effect on the acous-tic-based measures of door spread, wing spread, and headrope height off-bottom. However, the sensitivity of the trawl to 7 m of warp offset could be seen as footrope distances off-bottom increased slightly (particularly in the center region of the net where flatfish escapement is highest), and as the width of the bridle path responsible for flatfish herding, together with the effective net width, was reduced. For this survey trawl, a NOAA threshold value of 4% should be considered a maximum. A more conservative value (less than 4%) would likely reduce potential bias in estimates of relative abundance caused by large differences in warp length approaching 7 m.

The effect of autotrawl systems on the performance of a survey trawl

Three aspects of a survey bottom trawl performance—1) trawl geometry (i.e., net spread, door spread, and headrope height); 2) footrope distance off-bottom; and 3) bridle distance off-bottom—were compared among hauls by using either of two autotrawl systems (equal tension and net symmetry) and hauls conducted with towing cables of equal length and locked winches. The effects of environmental conditions, vessel heave, crabbing (i.e., the difference between vessel heading and actual vessel course over ground), and bottom current on trawl performance with three trawling modes were investigated. Means and standard deviations of trawl geometry measures were not significantly different between autotrawl and locked-winch systems. Bottom trawls performed better with either autotrawl system as compared to trawling with locked winches by reducing the variance and increasing the symmetry of the footrope contact with the bottom. The equal tension autotrawl system was most effective in counteracting effects of environmental conditions on footrope bottom contact. Footrope bottom contact was most inf luenced by environmental conditions during tows with locked winches. Both of the autotrawl systems also reduced the variance and increased the symmetry of bridle bottom contact. Autotrawl systems proved to be effective in decreasing the effects of environmental factors on some aspects of trawl performance and, as a result, have the potential to reduce among-haul variance in catchability of survey trawls. Therefore, by incorporating an autotrawl system into standard survey procedures, precision of survey estimates of relative abundance

Effects of Gear Modifications on the Trawl Performance and Catching Efficiency of the West Coast Upper Continental Slope Groundfish Survey Trawl

Since 1984, annual bottom trawl surveys of the west coast (California–Washington) upper continental slope (WCUCS) have provided information on the abundance, distribution, and biological characteristics of groundfish resources. Slope species of the deep-water complex (DWC) are of particular importance and include Dover sole, Microstomus pacificus; sablefish, Anoplopoma fimbria; shortspine thornyhead, Sebastolobus alascanus; and longspine thornyhead, S. altivelis. In the fall of 1994, we conducted an experimental gear research cruise in lieu of our normal survey because of concerns about the performance of the survey trawl. The experiment was conducted on a soft mud bottom at depths of 460–490 m off the central Oregon coast. Treatments included different combinations of door-bridle rigging, groundgear weight, and scope length. The experimental design was a 2 ´ 2 ´ 2 factorial within a randomized complete-block. Analysis of variance was used to examine the effects of gear modifications on the engineering performance of the trawl (i.e. trawl dimensions, variation in trawl dimensions, and door attitude) and to determine if catch rates in terms of weight and number of DWC species and invertebrates were affected by the gear modifications. Trawl performance was highly variable for the historically used standard trawl configuration. Improvements were observed with the addition of either a 2-bridle door or lighter ground gear. Changes in scope length had relatively little effect on trawl performance. The interaction of door bridle and ground gear weight had the most effect on trawl performance. In spite of the standard trawl’s erratic performance, catch rates of all four DWC species and invertebrates were not significantly different than the 2-bridle/heavy combination, which did the best in terms of engineering performance. The most important factor affecting DWC catch rates was ground gear. Scope length and the type of door bridle had little effect on DWC catch rates. Subsequent revisions to survey gear and towing protocol and their impact on the continuity of the slope survey time series are discussed.

Twin trawling for shrimp with dummy doors

Twin trawling; a new concept in shrimp trawling is described in this paper. It essentially involves towing of two trawls of equal size connected in sequence at the inner head and foot rope legs and using a pair of outer otter boards and central neutral door or dummy door with triple bridles and single tow warp. A comparative study with conventional stern trawling using a standard 13.7 m four seam shrimp trawl and two 6 8 m standard four seam trawls as twin-rig has shown considerable reduction in the utilization of power (20 %) with better efficiency in shrimp fishing.