Analytical study and evaluation results of power optimizers for distributed power conditioning in PV arrays

The use of modular or ‘micro’ maximum power point tracking (MPPT) converters at module level in series association, commercially known as “power optimizers”, allows the individual adaptation of each panel to the load, solving part of the problems related to partial shadows and different tilt and/or orientation angles of the photovoltaic (PV) modules. This is particularly relevant in building integrated PV systems. This paper presents useful behavioural analytical studies of cascade MPPT converters and evaluation test results of a prototype developed under a Spanish national research project. On the one hand, this work focuses on the development of new useful expressions which can be used to identify the behaviour of individual MPPT converters applied to each module and connected in series, in a typical grid-connected PV system. On the other hand, a novel characterization method of MPPT converters is developed, and experimental results of the prototype are obtained: when individual partial shading is applied, and they are connected in a typical grid connected PV array

Distributed collaborative processing in wireless sensor networks with application to target localization and beamforming

Abstract The proliferation of wireless sensor networks and the variety of envisioned applications associated with them has motivated the development of distributed algorithms for collaborative processing over networked systems. One of the applications that has attracted the attention of the researchers is that of target localization where the nodes of the network try to estimate the position of an unknown target that lies within its coverage area. Particularly challenging is the problem of estimating the target’s position when we use received signal strength indicator (RSSI) due to the nonlinear relationship between the measured signal and the true position of the target. Many of the existing approaches suffer either from high computational complexity (e.g., particle filters) or lack of accuracy. Further, many of the proposed solutions are centralized which make their application to a sensor network questionable. Depending on the application at hand and, from a practical perspective it could be convenient to find a balance between localization accuracy and complexity. Into this direction we approach the maximum likelihood location estimation problem by solving a suboptimal (and more tractable) problem. One of the main advantages of the proposed scheme is that it allows for a decentralized implementation using distributed processing tools (e.g., consensus and convex optimization) and therefore, it is very suitable to be implemented in real sensor networks. If further accuracy is needed an additional refinement step could be performed around the found solution. Under the assumption of independent noise among the nodes such local search can be done in a fully distributed way using a distributed version of the Gauss-Newton method based on consensus. Regardless of the underlying application or function of the sensor network it is al¬ways necessary to have a mechanism for data reporting. While some approaches use a special kind of nodes (called sink nodes) for data harvesting and forwarding to the outside world, there are however some scenarios where such an approach is impractical or even impossible to deploy. Further, such sink nodes become a bottleneck in terms of traffic flow and power consumption. To overcome these issues instead of using sink nodes for data reporting one could use collaborative beamforming techniques to forward directly the generated data to a base station or gateway to the outside world. In a dis-tributed environment like a sensor network nodes cooperate in order to form a virtual antenna array that can exploit the benefits of multi-antenna communications. In col-laborative beamforming nodes synchronize their phases in order to add constructively at the receiver. Some of the inconveniences associated with collaborative beamforming techniques is that there is no control over the radiation pattern since it is treated as a random quantity. This may cause interference to other coexisting systems and fast bat-tery depletion at the nodes. Since energy-efficiency is a major design issue we consider the development of a distributed collaborative beamforming scheme that maximizes the network lifetime while meeting some quality of service (QoS) requirement at the re¬ceiver side. Using local information about battery status and channel conditions we find distributed algorithms that converge to the optimal centralized beamformer. While in the first part we consider only battery depletion due to communications beamforming, we extend the model to account for more realistic scenarios by the introduction of an additional random energy consumption. It is shown how the new problem generalizes the original one and under which conditions it is easily solvable. By formulating the problem under the energy-efficiency perspective the network’s lifetime is significantly improved. Resumen La proliferación de las redes inalámbricas de sensores junto con la gran variedad de posi¬bles aplicaciones relacionadas, han motivado el desarrollo de herramientas y algoritmos necesarios para el procesado cooperativo en sistemas distribuidos. Una de las aplicaciones que suscitado mayor interés entre la comunidad científica es la de localization, donde el conjunto de nodos de la red intenta estimar la posición de un blanco localizado dentro de su área de cobertura. El problema de la localization es especialmente desafiante cuando se usan niveles de energía de la seal recibida (RSSI por sus siglas en inglés) como medida para la localization. El principal inconveniente reside en el hecho que el nivel de señal recibida no sigue una relación lineal con la posición del blanco. Muchas de las soluciones actuales al problema de localization usando RSSI se basan en complejos esquemas centralizados como filtros de partículas, mientas que en otras se basan en esquemas mucho más simples pero con menor precisión. Además, en muchos casos las estrategias son centralizadas lo que resulta poco prácticos para su implementación en redes de sensores. Desde un punto de vista práctico y de implementation, es conveniente, para ciertos escenarios y aplicaciones, el desarrollo de alternativas que ofrezcan un compromiso entre complejidad y precisión. En esta línea, en lugar de abordar directamente el problema de la estimación de la posición del blanco bajo el criterio de máxima verosimilitud, proponemos usar una formulación subóptima del problema más manejable analíticamente y que ofrece la ventaja de permitir en¬contrar la solución al problema de localization de una forma totalmente distribuida, convirtiéndola así en una solución atractiva dentro del contexto de redes inalámbricas de sensores. Para ello, se usan herramientas de procesado distribuido como los algorit¬mos de consenso y de optimización convexa en sistemas distribuidos. Para aplicaciones donde se requiera de un mayor grado de precisión se propone una estrategia que con¬siste en la optimización local de la función de verosimilitud entorno a la estimación inicialmente obtenida. Esta optimización se puede realizar de forma descentralizada usando una versión basada en consenso del método de Gauss-Newton siempre y cuando asumamos independencia de los ruidos de medida en los diferentes nodos. Independientemente de la aplicación subyacente de la red de sensores, es necesario tener un mecanismo que permita recopilar los datos provenientes de la red de sensores. Una forma de hacerlo es mediante el uso de uno o varios nodos especiales, llamados nodos “sumidero”, (sink en inglés) que actúen como centros recolectores de información y que estarán equipados con hardware adicional que les permita la interacción con el exterior de la red. La principal desventaja de esta estrategia es que dichos nodos se convierten en cuellos de botella en cuanto a tráfico y capacidad de cálculo. Como alter¬nativa se pueden usar técnicas cooperativas de conformación de haz (beamforming en inglés) de manera que el conjunto de la red puede verse como un único sistema virtual de múltiples antenas y, por tanto, que exploten los beneficios que ofrecen las comu¬nicaciones con múltiples antenas. Para ello, los distintos nodos de la red sincronizan sus transmisiones de manera que se produce una interferencia constructiva en el recep¬tor. No obstante, las actuales técnicas se basan en resultados promedios y asintóticos, cuando el número de nodos es muy grande. Para una configuración específica se pierde el control sobre el diagrama de radiación causando posibles interferencias sobre sis¬temas coexistentes o gastando más potencia de la requerida. La eficiencia energética es una cuestión capital en las redes inalámbricas de sensores ya que los nodos están equipados con baterías. Es por tanto muy importante preservar la batería evitando cambios innecesarios y el consecuente aumento de costes. Bajo estas consideraciones, se propone un esquema de conformación de haz que maximice el tiempo de vida útil de la red, entendiendo como tal el máximo tiempo que la red puede estar operativa garantizando unos requisitos de calidad de servicio (QoS por sus siglas en inglés) que permitan una decodificación fiable de la señal recibida en la estación base. Se proponen además algoritmos distribuidos que convergen a la solución centralizada. Inicialmente se considera que la única causa de consumo energético se debe a las comunicaciones con la estación base. Este modelo de consumo energético es modificado para tener en cuenta otras formas de consumo de energía derivadas de procesos inherentes al funcionamiento de la red como la adquisición y procesado de datos, las comunicaciones locales entre nodos, etc. Dicho consumo adicional de energía se modela como una variable aleatoria en cada nodo. Se cambia por tanto, a un escenario probabilístico que generaliza el caso determinista y se proporcionan condiciones bajo las cuales el problema se puede resolver de forma eficiente. Se demuestra que el tiempo de vida de la red mejora de forma significativa usando el criterio propuesto de eficiencia energética.

Advanced Topics in Resource Analysis: Certification, Incrementality, Concurrency and Array-Sensitivity

El Análisis de Consumo de Recursos o Análisis de Coste trata de aproximar el coste de ejecutar un programa como una función dependiente de sus datos de entrada. A pesar de que existen trabajos previos a esta tesis doctoral que desarrollan potentes marcos para el análisis de coste de programas orientados a objetos, algunos aspectos avanzados, como la eficiencia, la precisión y la fiabilidad de los resultados, todavía deben ser estudiados en profundidad. Esta tesis aborda estos aspectos desde cuatro perspectivas diferentes: (1) Las estructuras de datos compartidas en la memoria del programa son una pesadilla para el análisis estático de programas. Trabajos recientes proponen una serie de condiciones de localidad para poder mantener de forma consistente información sobre los atributos de los objetos almacenados en memoria compartida, reemplazando éstos por variables locales no almacenadas en la memoria compartida. En esta tesis presentamos dos extensiones a estos trabajos: la primera es considerar, no sólo los accesos a los atributos, sino también los accesos a los elementos almacenados en arrays; la segunda se centra en los casos en los que las condiciones de localidad no se cumplen de forma incondicional, para lo cual, proponemos una técnica para encontrar las precondiciones necesarias para garantizar la consistencia de la información acerca de los datos almacenados en memoria. (2) El objetivo del análisis incremental es, dado un programa, los resultados de su análisis y una serie de cambios sobre el programa, obtener los nuevos resultados del análisis de la forma más eficiente posible, evitando reanalizar aquellos fragmentos de código que no se hayan visto afectados por los cambios. Los analizadores actuales todavía leen y analizan el programa completo de forma no incremental. Esta tesis presenta un análisis de coste incremental, que, dado un cambio en el programa, reconstruye la información sobre el coste del programa de todos los métodos afectados por el cambio de forma incremental. Para esto, proponemos (i) un algoritmo multi-dominio y de punto fijo que puede ser utilizado en todos los análisis globales necesarios para inferir el coste, y (ii) una novedosa forma de almacenar las expresiones de coste que nos permite reconstruir de forma incremental únicamente las funciones de coste de aquellos componentes afectados por el cambio. (3) Las garantías de coste obtenidas de forma automática por herramientas de análisis estático no son consideradas totalmente fiables salvo que la implementación de la herramienta o los resultados obtenidos sean verificados formalmente. Llevar a cabo el análisis de estas herramientas es una tarea titánica, ya que se trata de herramientas de gran tamaño y complejidad. En esta tesis nos centramos en el desarrollo de un marco formal para la verificación de las garantías de coste obtenidas por los analizadores en lugar de analizar las herramientas. Hemos implementado esta idea mediante la herramienta COSTA, un analizador de coste para programas Java y KeY, una herramienta de verificación de programas Java. De esta forma, COSTA genera las garantías de coste, mientras que KeY prueba la validez formal de los resultados obtenidos, generando de esta forma garantías de coste verificadas. (4) Hoy en día la concurrencia y los programas distribuidos son clave en el desarrollo de software. Los objetos concurrentes son un modelo de concurrencia asentado para el desarrollo de sistemas concurrentes. En este modelo, los objetos son las unidades de concurrencia y se comunican entre ellos mediante llamadas asíncronas a sus métodos. La distribución de las tareas sugiere que el análisis de coste debe inferir el coste de los diferentes componentes distribuidos por separado. En esta tesis proponemos un análisis de coste sensible a objetos que, utilizando los resultados obtenidos mediante un análisis de apunta-a, mantiene el coste de los diferentes componentes de forma independiente. Abstract Resource Analysis (a.k.a. Cost Analysis) tries to approximate the cost of executing programs as functions on their input data sizes and without actually having to execute the programs. While a powerful resource analysis framework on object-oriented programs existed before this thesis, advanced aspects to improve the efficiency, the accuracy and the reliability of the results of the analysis still need to be further investigated. This thesis tackles this need from the following four different perspectives. (1) Shared mutable data structures are the bane of formal reasoning and static analysis. Analyses which keep track of heap-allocated data are referred to as heap-sensitive. Recent work proposes locality conditions for soundly tracking field accesses by means of ghost non-heap allocated variables. In this thesis we present two extensions to this approach: the first extension is to consider arrays accesses (in addition to object fields), while the second extension focuses on handling cases for which the locality conditions cannot be proven unconditionally by finding aliasing preconditions under which tracking such heap locations is feasible. (2) The aim of incremental analysis is, given a program, its analysis results and a series of changes to the program, to obtain the new analysis results as efficiently as possible and, ideally, without having to (re-)analyze fragments of code that are not affected by the changes. During software development, programs are permanently modified but most analyzers still read and analyze the entire program at once in a non-incremental way. This thesis presents an incremental resource usage analysis which, after a change in the program is made, is able to reconstruct the upper-bounds of all affected methods in an incremental way. To this purpose, we propose (i) a multi-domain incremental fixed-point algorithm which can be used by all global analyses required to infer the cost, and (ii) a novel form of cost summaries that allows us to incrementally reconstruct only those components of cost functions affected by the change. (3) Resource guarantees that are automatically inferred by static analysis tools are generally not considered completely trustworthy, unless the tool implementation or the results are formally verified. Performing full-blown verification of such tools is a daunting task, since they are large and complex. In this thesis we focus on the development of a formal framework for the verification of the resource guarantees obtained by the analyzers, instead of verifying the tools. We have implemented this idea using COSTA, a state-of-the-art cost analyzer for Java programs and KeY, a state-of-the-art verification tool for Java source code. COSTA is able to derive upper-bounds of Java programs while KeY proves the validity of these bounds and provides a certificate. The main contribution of our work is to show that the proposed tools cooperation can be used for automatically producing verified resource guarantees. (4) Distribution and concurrency are today mainstream. Concurrent objects form a well established model for distributed concurrent systems. In this model, objects are the concurrency units that communicate via asynchronous method calls. Distribution suggests that analysis must infer the cost of the diverse distributed components separately. In this thesis we propose a novel object-sensitive cost analysis which, by using the results gathered by a points-to analysis, can keep the cost of the diverse distributed components separate.

A new analog trigger system for the Cherenkov Telescope array

La astronomía de rayos γ estudia las partículas más energéticas que llegan a la Tierra desde el espacio. Estos rayos γ no se generan mediante procesos térmicos en simples estrellas, sino mediante mecanismos de aceleración de partículas en objetos celestes como núcleos de galaxias activos, púlsares, supernovas, o posibles procesos de aniquilación de materia oscura. Los rayos γ procedentes de estos objetos y sus características proporcionan una valiosa información con la que los científicos tratan de comprender los procesos físicos que ocurren en ellos y desarrollar modelos teóricos que describan su funcionamiento con fidelidad. El problema de observar rayos γ es que son absorbidos por las capas altas de la atmósfera y no llegan a la superficie (de lo contrario, la Tierra será inhabitable). De este modo, sólo hay dos formas de observar rayos γ embarcar detectores en satélites, u observar los efectos secundarios que los rayos γ producen en la atmósfera. Cuando un rayo γ llega a la atmósfera, interacciona con las partículas del aire y genera un par electrón - positrón, con mucha energía. Estas partículas secundarias generan a su vez más partículas secundarias cada vez menos energéticas. Estas partículas, mientras aún tienen energía suficiente para viajar más rápido que la velocidad de la luz en el aire, producen una radiación luminosa azulada conocida como radiación Cherenkov durante unos pocos nanosegundos. Desde la superficie de la Tierra, algunos telescopios especiales, conocidos como telescopios Cherenkov o IACTs (Imaging Atmospheric Cherenkov Telescopes), son capaces de detectar la radiación Cherenkov e incluso de tomar imágenes de la forma de la cascada Cherenkov. A partir de estas imágenes es posible conocer las principales características del rayo γ original, y con suficientes rayos se pueden deducir características importantes del objeto que los emitió, a cientos de años luz de distancia. Sin embargo, detectar cascadas Cherenkov procedentes de rayos γ no es nada fácil. Las cascadas generadas por fotones γ de bajas energías emiten pocos fotones, y durante pocos nanosegundos, y las correspondientes a rayos γ de alta energía, si bien producen más electrones y duran más, son más improbables conforme mayor es su energía. Esto produce dos líneas de desarrollo de telescopios Cherenkov: Para observar cascadas de bajas energías son necesarios grandes reflectores que recuperen muchos fotones de los pocos que tienen estas cascadas. Por el contrario, las cascadas de altas energías se pueden detectar con telescopios pequeños, pero conviene cubrir con ellos una superficie grande en el suelo para aumentar el número de eventos detectados. Con el objetivo de mejorar la sensibilidad de los telescopios Cherenkov actuales, en el rango de energía alto (> 10 TeV), medio (100 GeV - 10 TeV) y bajo (10 GeV - 100 GeV), nació el proyecto CTA (Cherenkov Telescope Array). Este proyecto en el que participan más de 27 países, pretende construir un observatorio en cada hemisferio, cada uno de los cuales contará con 4 telescopios grandes (LSTs), unos 30 medianos (MSTs) y hasta 70 pequeños (SSTs). Con un array así, se conseguirán dos objetivos. En primer lugar, al aumentar drásticamente el área de colección respecto a los IACTs actuales, se detectarán más rayos γ en todos los rangos de energía. En segundo lugar, cuando una misma cascada Cherenkov es observada por varios telescopios a la vez, es posible analizarla con mucha más precisión gracias a las técnicas estereoscópicas. La presente tesis recoge varios desarrollos técnicos realizados como aportación a los telescopios medianos y grandes de CTA, concretamente al sistema de trigger. Al ser las cascadas Cherenkov tan breves, los sistemas que digitalizan y leen los datos de cada píxel tienen que funcionar a frecuencias muy altas (≈1 GHz), lo que hace inviable que funcionen de forma continua, ya que la cantidad de datos guardada será inmanejable. En su lugar, las señales analógicas se muestrean, guardando las muestras analógicas en un buffer circular de unos pocos µs. Mientras las señales se mantienen en el buffer, el sistema de trigger hace un análisis rápido de las señales recibidas, y decide si la imagen que hay en el buér corresponde a una cascada Cherenkov y merece ser guardada, o por el contrario puede ignorarse permitiendo que el buffer se sobreescriba. La decisión de si la imagen merece ser guardada o no, se basa en que las cascadas Cherenkov producen detecciones de fotones en píxeles cercanos y en tiempos muy próximos, a diferencia de los fotones de NSB (night sky background), que llegan aleatoriamente. Para detectar cascadas grandes es suficiente con comprobar que más de un cierto número de píxeles en una región hayan detectado más de un cierto número de fotones en una ventana de tiempo de algunos nanosegundos. Sin embargo, para detectar cascadas pequeñas es más conveniente tener en cuenta cuántos fotones han sido detectados en cada píxel (técnica conocida como sumtrigger). El sistema de trigger desarrollado en esta tesis pretende optimizar la sensibilidad a bajas energías, por lo que suma analógicamente las señales recibidas en cada píxel en una región de trigger y compara el resultado con un umbral directamente expresable en fotones detectados (fotoelectrones). El sistema diseñado permite utilizar regiones de trigger de tamaño seleccionable entre 14, 21 o 28 píxeles (2, 3, o 4 clusters de 7 píxeles cada uno), y con un alto grado de solapamiento entre ellas. De este modo, cualquier exceso de luz en una región compacta de 14, 21 o 28 píxeles es detectado y genera un pulso de trigger. En la versión más básica del sistema de trigger, este pulso se distribuye por toda la cámara de forma que todos los clusters sean leídos al mismo tiempo, independientemente de su posición en la cámara, a través de un delicado sistema de distribución. De este modo, el sistema de trigger guarda una imagen completa de la cámara cada vez que se supera el número de fotones establecido como umbral en una región de trigger. Sin embargo, esta forma de operar tiene dos inconvenientes principales. En primer lugar, la cascada casi siempre ocupa sólo una pequeña zona de la cámara, por lo que se guardan muchos píxeles sin información alguna. Cuando se tienen muchos telescopios como será el caso de CTA, la cantidad de información inútil almacenada por este motivo puede ser muy considerable. Por otro lado, cada trigger supone guardar unos pocos nanosegundos alrededor del instante de disparo. Sin embargo, en el caso de cascadas grandes la duración de las mismas puede ser bastante mayor, perdiéndose parte de la información debido al truncamiento temporal. Para resolver ambos problemas se ha propuesto un esquema de trigger y lectura basado en dos umbrales. El umbral alto decide si hay un evento en la cámara y, en caso positivo, sólo las regiones de trigger que superan el nivel bajo son leídas, durante un tiempo más largo. De este modo se evita guardar información de píxeles vacíos y las imágenes fijas de las cascadas se pueden convertir en pequeños \vídeos" que representen el desarrollo temporal de la cascada. Este nuevo esquema recibe el nombre de COLIBRI (Concept for an Optimized Local Image Building and Readout Infrastructure), y se ha descrito detalladamente en el capítulo 5. Un problema importante que afecta a los esquemas de sumtrigger como el que se presenta en esta tesis es que para sumar adecuadamente las señales provenientes de cada píxel, estas deben tardar lo mismo en llegar al sumador. Los fotomultiplicadores utilizados en cada píxel introducen diferentes retardos que deben compensarse para realizar las sumas adecuadamente. El efecto de estos retardos ha sido estudiado, y se ha desarrollado un sistema para compensarlos. Por último, el siguiente nivel de los sistemas de trigger para distinguir efectivamente las cascadas Cherenkov del NSB consiste en buscar triggers simultáneos (o en tiempos muy próximos) en telescopios vecinos. Con esta función, junto con otras de interfaz entre sistemas, se ha desarrollado un sistema denominado Trigger Interface Board (TIB). Este sistema consta de un módulo que irá montado en la cámara de cada LST o MST, y que estará conectado mediante fibras ópticas a los telescopios vecinos. Cuando un telescopio tiene un trigger local, este se envía a todos los vecinos conectados y viceversa, de modo que cada telescopio sabe si sus vecinos han dado trigger. Una vez compensadas las diferencias de retardo debidas a la propagación en las fibras ópticas y de los propios fotones Cherenkov en el aire dependiendo de la dirección de apuntamiento, se buscan coincidencias, y en el caso de que la condición de trigger se cumpla, se lee la cámara en cuestión, de forma sincronizada con el trigger local. Aunque todo el sistema de trigger es fruto de la colaboración entre varios grupos, fundamentalmente IFAE, CIEMAT, ICC-UB y UCM en España, con la ayuda de grupos franceses y japoneses, el núcleo de esta tesis son el Level 1 y la Trigger Interface Board, que son los dos sistemas en los que que el autor ha sido el ingeniero principal. Por este motivo, en la presente tesis se ha incluido abundante información técnica relativa a estos sistemas. Existen actualmente importantes líneas de desarrollo futuras relativas tanto al trigger de la cámara (implementación en ASICs), como al trigger entre telescopios (trigger topológico), que darán lugar a interesantes mejoras sobre los diseños actuales durante los próximos años, y que con suerte serán de provecho para toda la comunidad científica participante en CTA. ABSTRACT -ray astronomy studies the most energetic particles arriving to the Earth from outer space. This -rays are not generated by thermal processes in mere stars, but by means of particle acceleration mechanisms in astronomical objects such as active galactic nuclei, pulsars, supernovas or as a result of dark matter annihilation processes. The γ rays coming from these objects and their characteristics provide with valuable information to the scientist which try to understand the underlying physical fundamentals of these objects, as well as to develop theoretical models able to describe them accurately. The problem when observing rays is that they are absorbed in the highest layers of the atmosphere, so they don't reach the Earth surface (otherwise the planet would be uninhabitable). Therefore, there are only two possible ways to observe γ rays: by using detectors on-board of satellites, or by observing their secondary effects in the atmosphere. When a γ ray reaches the atmosphere, it interacts with the particles in the air generating a highly energetic electron-positron pair. These secondary particles generate in turn more particles, with less energy each time. While these particles are still energetic enough to travel faster than the speed of light in the air, they produce a bluish radiation known as Cherenkov light during a few nanoseconds. From the Earth surface, some special telescopes known as Cherenkov telescopes or IACTs (Imaging Atmospheric Cherenkov Telescopes), are able to detect the Cherenkov light and even to take images of the Cherenkov showers. From these images it is possible to know the main parameters of the original -ray, and with some -rays it is possible to deduce important characteristics of the emitting object, hundreds of light-years away. However, detecting Cherenkov showers generated by γ rays is not a simple task. The showers generated by low energy -rays contain few photons and last few nanoseconds, while the ones corresponding to high energy -rays, having more photons and lasting more time, are much more unlikely. This results in two clearly differentiated development lines for IACTs: In order to detect low energy showers, big reflectors are required to collect as much photons as possible from the few ones that these showers have. On the contrary, small telescopes are able to detect high energy showers, but a large area in the ground should be covered to increase the number of detected events. With the aim to improve the sensitivity of current Cherenkov showers in the high (> 10 TeV), medium (100 GeV - 10 TeV) and low (10 GeV - 100 GeV) energy ranges, the CTA (Cherenkov Telescope Array) project was created. This project, with more than 27 participating countries, intends to build an observatory in each hemisphere, each one equipped with 4 large size telescopes (LSTs), around 30 middle size telescopes (MSTs) and up to 70 small size telescopes (SSTs). With such an array, two targets would be achieved. First, the drastic increment in the collection area with respect to current IACTs will lead to detect more -rays in all the energy ranges. Secondly, when a Cherenkov shower is observed by several telescopes at the same time, it is possible to analyze it much more accurately thanks to the stereoscopic techniques. The present thesis gathers several technical developments for the trigger system of the medium and large size telescopes of CTA. As the Cherenkov showers are so short, the digitization and readout systems corresponding to each pixel must work at very high frequencies (_ 1 GHz). This makes unfeasible to read data continuously, because the amount of data would be unmanageable. Instead, the analog signals are sampled, storing the analog samples in a temporal ring buffer able to store up to a few _s. While the signals remain in the buffer, the trigger system performs a fast analysis of the signals and decides if the image in the buffer corresponds to a Cherenkov shower and deserves to be stored, or on the contrary it can be ignored allowing the buffer to be overwritten. The decision of saving the image or not, is based on the fact that Cherenkov showers produce photon detections in close pixels during near times, in contrast to the random arrival of the NSB phtotons. Checking if more than a certain number of pixels in a trigger region have detected more than a certain number of photons during a certain time window is enough to detect large showers. However, taking also into account how many photons have been detected in each pixel (sumtrigger technique) is more convenient to optimize the sensitivity to low energy showers. The developed trigger system presented in this thesis intends to optimize the sensitivity to low energy showers, so it performs the analog addition of the signals received in each pixel in the trigger region and compares the sum with a threshold which can be directly expressed as a number of detected photons (photoelectrons). The trigger system allows to select trigger regions of 14, 21, or 28 pixels (2, 3 or 4 clusters with 7 pixels each), and with extensive overlapping. In this way, every light increment inside a compact region of 14, 21 or 28 pixels is detected, and a trigger pulse is generated. In the most basic version of the trigger system, this pulse is just distributed throughout the camera in such a way that all the clusters are read at the same time, independently from their position in the camera, by means of a complex distribution system. Thus, the readout saves a complete camera image whenever the number of photoelectrons set as threshold is exceeded in a trigger region. However, this way of operating has two important drawbacks. First, the shower usually covers only a little part of the camera, so many pixels without relevant information are stored. When there are many telescopes as will be the case of CTA, the amount of useless stored information can be very high. On the other hand, with every trigger only some nanoseconds of information around the trigger time are stored. In the case of large showers, the duration of the shower can be quite larger, loosing information due to the temporal cut. With the aim to solve both limitations, a trigger and readout scheme based on two thresholds has been proposed. The high threshold decides if there is a relevant event in the camera, and in the positive case, only the trigger regions exceeding the low threshold are read, during a longer time. In this way, the information from empty pixels is not stored and the fixed images of the showers become to little \`videos" containing the temporal development of the shower. This new scheme is named COLIBRI (Concept for an Optimized Local Image Building and Readout Infrastructure), and it has been described in depth in chapter 5. An important problem affecting sumtrigger schemes like the one presented in this thesis is that in order to add the signals from each pixel properly, they must arrive at the same time. The photomultipliers used in each pixel introduce different delays which must be compensated to perform the additions properly. The effect of these delays has been analyzed, and a delay compensation system has been developed. The next trigger level consists of looking for simultaneous (or very near in time) triggers in neighbour telescopes. These function, together with others relating to interfacing different systems, have been developed in a system named Trigger Interface Board (TIB). This system is comprised of one module which will be placed inside the LSTs and MSTs cameras, and which will be connected to the neighbour telescopes through optical fibers. When a telescope receives a local trigger, it is resent to all the connected neighbours and vice-versa, so every telescope knows if its neighbours have been triggered. Once compensated the delay differences due to propagation in the optical fibers and in the air depending on the pointing direction, the TIB looks for coincidences, and in the case that the trigger condition is accomplished, the camera is read a fixed time after the local trigger arrived. Despite all the trigger system is the result of the cooperation of several groups, specially IFAE, Ciemat, ICC-UB and UCM in Spain, with some help from french and japanese groups, the Level 1 and the Trigger Interface Board constitute the core of this thesis, as they have been the two systems designed by the author of the thesis. For this reason, a large amount of technical information about these systems has been included. There are important future development lines regarding both the camera trigger (implementation in ASICS) and the stereo trigger (topological trigger), which will produce interesting improvements for the current designs during the following years, being useful for all the scientific community participating in CTA.

Communication Middleware for Distributed Hard Real-Time Systems in Java

Distributed real-time embedded systems are becoming increasingly important to society. More demands will be made on them and greater reliance will be placed on the delivery of their services. A relevant subset of them is high-integrity or hard real-time systems, where failure can cause loss of life, environmental harm, or significant financial loss. Additionally, the evolution of communication networks and paradigms as well as the necessity of demanding processing power and fault tolerance, motivated the interconnection between electronic devices; many of the communications have the possibility of transferring data at a high speed. The concept of distributed systems emerged as systems where different parts are executed on several nodes that interact with each other via a communication network. Java’s popularity, facilities and platform independence have made it an interesting language for the real-time and embedded community. This was the motivation for the development of RTSJ (Real-Time Specification for Java), which is a language extension intended to allow the development of real-time systems. The use of Java in the development of high-integrity systems requires strict development and testing techniques. However, RTJS includes a number of language features that are forbidden in such systems. In the context of the HIJA project, the HRTJ (Hard Real-Time Java) profile was developed to define a robust subset of the language that is amenable to static analysis for high-integrity system certification. Currently, a specification under the Java community process (JSR- 302) is being developed. Its purpose is to define those capabilities needed to create safety critical applications with Java technology called Safety Critical Java (SCJ). However, neither RTSJ nor its profiles provide facilities to develop distributed realtime applications. This is an important issue, as most of the current and future systems will be distributed. The Distributed RTSJ (DRTSJ) Expert Group was created under the Java community process (JSR-50) in order to define appropriate abstractions to overcome this problem. Currently there is no formal specification. The aim of this thesis is to develop a communication middleware that is suitable for the development of distributed hard real-time systems in Java, based on the integration between the RMI (Remote Method Invocation) model and the HRTJ profile. It has been designed and implemented keeping in mind the main requirements such as the predictability and reliability in the timing behavior and the resource usage. iThe design starts with the definition of a computational model which identifies among other things: the communication model, most appropriate underlying network protocols, the analysis model, and a subset of Java for hard real-time systems. In the design, the remote references are the basic means for building distributed applications which are associated with all non-functional parameters and resources needed to implement synchronous or asynchronous remote invocations with real-time attributes. The proposed middleware separates the resource allocation from the execution itself by defining two phases and a specific threading mechanism that guarantees a suitable timing behavior. It also includes mechanisms to monitor the functional and the timing behavior. It provides independence from network protocol defining a network interface and modules. The JRMP protocol was modified to include two phases, non-functional parameters, and message size optimizations. Although serialization is one of the fundamental operations to ensure proper data transmission, current implementations are not suitable for hard real-time systems and there are no alternatives. This thesis proposes a predictable serialization that introduces a new compiler to generate optimized code according to the computational model. The proposed solution has the advantage of allowing us to schedule the communications and to adjust the memory usage at compilation time. In order to validate the design and the implementation a demanding validation process was carried out with emphasis in the functional behavior, the memory usage, the processor usage (the end-to-end response time and the response time in each functional block) and the network usage (real consumption according to the calculated consumption). The results obtained in an industrial application developed by Thales Avionics (a Flight Management System) and in exhaustive tests show that the design and the prototype are reliable for industrial applications with strict timing requirements. Los sistemas empotrados y distribuidos de tiempo real son cada vez más importantes para la sociedad. Su demanda aumenta y cada vez más dependemos de los servicios que proporcionan. Los sistemas de alta integridad constituyen un subconjunto de gran importancia. Se caracterizan por que un fallo en su funcionamiento puede causar pérdida de vidas humanas, daños en el medio ambiente o cuantiosas pérdidas económicas. La necesidad de satisfacer requisitos temporales estrictos, hace más complejo su desarrollo. Mientras que los sistemas empotrados se sigan expandiendo en nuestra sociedad, es necesario garantizar un coste de desarrollo ajustado mediante el uso técnicas adecuadas en su diseño, mantenimiento y certificación. En concreto, se requiere una tecnología flexible e independiente del hardware. La evolución de las redes y paradigmas de comunicación, así como la necesidad de mayor potencia de cómputo y de tolerancia a fallos, ha motivado la interconexión de dispositivos electrónicos. Los mecanismos de comunicación permiten la transferencia de datos con alta velocidad de transmisión. En este contexto, el concepto de sistema distribuido ha emergido como sistemas donde sus componentes se ejecutan en varios nodos en paralelo y que interactúan entre ellos mediante redes de comunicaciones. Un concepto interesante son los sistemas de tiempo real neutrales respecto a la plataforma de ejecución. Se caracterizan por la falta de conocimiento de esta plataforma durante su diseño. Esta propiedad es relevante, por que conviene que se ejecuten en la mayor variedad de arquitecturas, tienen una vida media mayor de diez anos y el lugar ˜ donde se ejecutan puede variar. El lenguaje de programación Java es una buena base para el desarrollo de este tipo de sistemas. Por este motivo se ha creado RTSJ (Real-Time Specification for Java), que es una extensión del lenguaje para permitir el desarrollo de sistemas de tiempo real. Sin embargo, RTSJ no proporciona facilidades para el desarrollo de aplicaciones distribuidas de tiempo real. Es una limitación importante dado que la mayoría de los actuales y futuros sistemas serán distribuidos. El grupo DRTSJ (DistributedRTSJ) fue creado bajo el proceso de la comunidad de Java (JSR-50) con el fin de definir las abstracciones que aborden dicha limitación, pero en la actualidad aun no existe una especificacion formal. El objetivo de esta tesis es desarrollar un middleware de comunicaciones para el desarrollo de sistemas distribuidos de tiempo real en Java, basado en la integración entre el modelo de RMI (Remote Method Invocation) y el perfil HRTJ. Ha sido diseñado e implementado teniendo en cuenta los requisitos principales, como la predecibilidad y la confiabilidad del comportamiento temporal y el uso de recursos. El diseño parte de la definición de un modelo computacional el cual identifica entre otras cosas: el modelo de comunicaciones, los protocolos de red subyacentes más adecuados, el modelo de análisis, y un subconjunto de Java para sistemas de tiempo real crítico. En el diseño, las referencias remotas son el medio básico para construcción de aplicaciones distribuidas las cuales son asociadas a todos los parámetros no funcionales y los recursos necesarios para la ejecución de invocaciones remotas síncronas o asíncronas con atributos de tiempo real. El middleware propuesto separa la asignación de recursos de la propia ejecución definiendo dos fases y un mecanismo de hebras especifico que garantiza un comportamiento temporal adecuado. Además se ha incluido mecanismos para supervisar el comportamiento funcional y temporal. Se ha buscado independencia del protocolo de red definiendo una interfaz de red y módulos específicos. También se ha modificado el protocolo JRMP para incluir diferentes fases, parámetros no funcionales y optimizaciones de los tamaños de los mensajes. Aunque la serialización es una de las operaciones fundamentales para asegurar la adecuada transmisión de datos, las actuales implementaciones no son adecuadas para sistemas críticos y no hay alternativas. Este trabajo propone una serialización predecible que ha implicado el desarrollo de un nuevo compilador para la generación de código optimizado acorde al modelo computacional. La solución propuesta tiene la ventaja que en tiempo de compilación nos permite planificar las comunicaciones y ajustar el uso de memoria. Con el objetivo de validar el diseño e implementación se ha llevado a cabo un exigente proceso de validación con énfasis en: el comportamiento funcional, el uso de memoria, el uso del procesador (tiempo de respuesta de extremo a extremo y en cada uno de los bloques funcionales) y el uso de la red (consumo real conforme al estimado). Los buenos resultados obtenidos en una aplicación industrial desarrollada por Thales Avionics (un sistema de gestión de vuelo) y en las pruebas exhaustivas han demostrado que el diseño y el prototipo son fiables para aplicaciones industriales con estrictos requisitos temporales.

Distributed power generation in the United States

With electricity consumption increasing within the UnitedStates, new paradigms of delivering electricity are required in order to meet demand. One promising option is the increased use of distributedpowergeneration. Already a growing percentage of electricity generation, distributedgeneration locates the power plant physically close to the consumer, avoiding transmission and distribution losses as well as providing the possibility of combined heat and power. Despite the efficiency gains possible, regulators and utilities have been reluctant to implement distributedgeneration, creating numerous technical, regulatory, and business barriers. Certain governments, most notable California, are making concerted efforts to overcome these barriers in order to ensure distributedgeneration plays a part as the country meets demand while shifting to cleaner sources of energy.

Distributed Data Management in 2020?

Work on distributed data management commenced shortly after the introduction of the relational model in the mid-1970's. 1970's and 1980's were very active periods for the development of distributed relational database technology, and claims were made that in the following ten years centralized databases will be an “antique curiosity” and most organizations will move toward distributed database managers [1]. That prediction has certainly become true, and all commercial DBMSs today are distributed.

B-Neck: A Distributed and Quiescent Max-Min Fair Algorithm

The problem of fairly distributing the capacity of a network among a set of sessions has been widely studied. In this problem, each session connects via a single path a source and a destination, and its goal is to maximize its assigned transmission rate (i.e., its throughput). Since the links of the network have limited bandwidths, some criterion has to be defined to fairly distribute their capacity among the sessions. A popular criterion is max-min fairness that, in short, guarantees that each session i gets a rate λi such that no session s can increase λs without causing another session s' to end up with a rate λs/ <; λs. Many max-min fair algorithms have been proposed, both centralized and distributed. However, to our knowledge, all proposed distributed algorithms require control data being continuously transmitted to recompute the max-min fair rates when needed (because none of them has mechanisms to detect convergence to the max-min fair rates). In this paper we propose B-Neck, a distributed max-min fair algorithm that is also quiescent. This means that, in absence of changes (i.e., session arrivals or departures), once the max min rates have been computed, B-Neck stops generating network traffic. Quiescence is a key design concept of B-Neck, because B-Neck routers are capable of detecting and notifying changes in the convergence conditions of max-min fair rates. As far as we know, B-Neck is the first distributed max-min fair algorithm that does not require a continuous injection of control traffic to compute the rates. The correctness of B-Neck is formally proved, and extensive simulations are conducted. In them, it is shown that B-Neck converges relatively fast and behaves nicely in presence of sessions arriving and departing.

Distributed models in P-Systems architectures to reduce computation time

Membrane systems are computational equivalent to Turing machines. However, their distributed and massively parallel nature obtains polynomial solutions opposite to traditional non-polynomial ones. At this point, it is very important to develop dedicated hardware and software implementations exploiting those two membrane systems features. Dealing with distributed implementations of P systems, the bottleneck communication problem has arisen. When the number of membranes grows up, the network gets congested. The purpose of distributed architectures is to reach a compromise between the massively parallel character of the system and the needed evolution step time to transit from one configuration of the system to the next one, solving the bottleneck communication problem. The goal of this paper is twofold. Firstly, to survey in a systematic and uniform way the main results regarding the way membranes can be placed on processors in order to get a software/hardware simulation of P-Systems in a distributed environment. Secondly, we improve some results about the membrane dissolution problem, prove that it is connected, and discuss the possibility of simulating this property in the distributed model. All this yields an improvement in the system parallelism implementation since it gets an increment of the parallelism of the external communication among processors. Proposed ideas improve previous architectures to tackle the communication bottleneck problem, such as reduction of the total time of an evolution step, increase of the number of membranes that could run on a processor and reduction of the number of processors.

Extended Triple-Junction Solar Cell 3D Distributed Model: Application to Chromatic Aberration-Related Losses

An extended 3D distributed model based on distributed circuit units for the simulation of triple‐junction solar cells under realistic conditions for the light distribution has been developed. A special emphasis has been put in the capability of the model to accurately account for current mismatch and chromatic aberration effects. This model has been validated, as shown by the good agreement between experimental and simulation results, for different light spot characteristics including spectral mismatch and irradiance non‐uniformities. This model is then used for the prediction of the performance of a triple‐junction solar cell for a light spot corresponding to a real optical architecture in order to illustrate its suitability in assisting concentrator system analysis and design process.

Analysis of Chromatic Aberration Effects in Triple-Junction Solar Cells Using Advanced Distributed Models

The consideration of real operating conditions for the design and optimization of a multijunction solar cell receiver-concentrator assembly is indispensable. Such a requirement involves the need for suitable modeling and simulation tools in order to complement the experimental work and circumvent its well-known burdens and restrictions. Three-dimensional distributed models have been demonstrated in the past to be a powerful choice for the analysis of distributed phenomena in single- and dual-junction solar cells, as well as for the design of strategies to minimize the solar cell losses when operating under high concentrations. In this paper, we present the application of these models for the analysis of triple-junction solar cells under real operating conditions. The impact of different chromatic aberration profiles on the short-circuit current of triple-junction solar cells is analyzed in detail using the developed distributed model. Current spreading conditions the impact of a given chromatic aberration profile on the solar cell I-V curve. The focus is put on determining the role of current spreading in the connection between photocurrent profile, subcell voltage and current, and semiconductor layers sheet resistance.

Planar compact array with parasitic elements for MIMO systems

A compact planar array with parasitic elements is studied to be used in MIMO systems. Classical compact arrays suffer from high coupling which makes correlation and matching efficiency to be worse. A proper matching network improves these lacks although its bandwidth is low and may increase the antenna size. The proposed antenna makes use of parasitic elements to improve both correlation and efficiency. A specific software based on MoM has been developed to analyze radiating structures with several feed points. The array is optimized through a Genetic Algorithm to determine parasitic elements position in order to fulfill different figures of merit. The proposed design provides the required correlation and matching efficiency to have a good performance over a significant bandwidth.

Parallel and Distributed Data Management. Introduction

The manipulation and handling of an ever increasing volume of data by current data-intensive applications require novel techniques for e?cient data management. Despite recent advances in every aspect of data management (storage, access, querying, analysis, mining), future applications are expected to scale to even higher degrees, not only in terms of volumes of data handled but also in terms of users and resources, often making use of multiple, pre-existing autonomous, distributed or heterogeneous resources.

Low-Profile Dual Circularly Polarized Antenna Array for Satellite Communications in the X Band

A planar antenna is introduced that works as a portable system for X-band satellite communications. This antenna is low-profile and modular with dimensions of 40 × 40 × 2.5 × cm. It is composed of a square array of 144 printed circuit elements that cover a wide bandwidth (14.7%) for transmission and reception along with dual and interchangeable circular polarization. A radiation efficiency above 50% is achieved by a low-loss stripline feeding network. This printed antenna has a 3 dB beamwidth of 5°, a maximum gain of 26 dBi and an axial ratio under 1.9 dB over the entire frequency band. The complete design of the antenna is shown, and the measurements are compared with simulations to reveal very good agreement.

Membrane Dissolution in Distributed Architectures of P-Systems

The goal of this paper is twofold. Firstly, to survey in a systematic and uniform way the main results regarding the way membranes can be placed on processors in order to get a software/hardware simulation of P-Systems in a distributed environment. Secondly, we improve some results about the membrane dissolution problem, prove that it is connected, and discuss the possibility of simulating this property in the distributed model. All this yields an improvement in the system parallelism implementation since it gets an increment of the parallelism of the external communication among processors. Also, the number of processors grows in such a way that is notorious the increment of the parallelism in the application of the evolution rules and the internal communica-tionsstudy because it gets an increment of the parallelism in the application of the evolution rules and the internal communications. Proposed ideas improve previous architectures to tackle the communication bottleneck problem, such as reduction of the total time of an evolution step, increase of the number of membranes that could run on a processor and reduction of the number of processors