Design of Reinforcement in Concrete Shells: a unified Approach

The problem of design/verification of reinforcement in concrete shells is reviewed. Methods of analysis are classified, and the elastic-plastic approach is described in detail in the general case of shells subjected to both bending and membrane action. The procedure is then reduced to membrane shells (applicable also to concrete walls) and to pure bending, as in the case of plates. The procedure, which is based on previous research,generally requires the use of a desk-top computer.

The Balanced Cross-Layer Design Routing Algorithm in Wireless Sensor Networks Using Fuzzy Logic

Recently, the cross-layer design for the wireless sensor network communication protocol has become more and more important and popular. Considering the disadvantages of the traditional cross-layer routing algorithms, in this paper we propose a new fuzzy logic-based routing algorithm, named the Balanced Cross-layer Fuzzy Logic (BCFL) routing algorithm. In BCFL, we use the cross-layer parameters’ dispersion as the fuzzy logic inference system inputs. Moreover, we give each cross-layer parameter a dynamic weight according the value of the dispersion. For getting a balanced solution, the parameter whose dispersion is large will have small weight, and vice versa. In order to compare it with the traditional cross-layer routing algorithms, BCFL is evaluated through extensive simulations. The simulation results show that the new routing algorithm can handle the multiple constraints without increasing the complexity of the algorithm and can achieve the most balanced performance on selecting the next hop relay node. Moreover, the Balanced Cross-layer Fuzzy Logic routing algorithm can adapt to the dynamic changing of the network conditions and topology effectively.

Development of Efficient Techniques for the Analysis and Design of Antennas in Dual-Reflectarray Configuration

This thesis contributes to the analysis and design of printed reflectarray antennas. The main part of the work is focused on the analysis of dual offset antennas comprising two reflectarray surfaces, one of them acts as sub-reflector and the second one acts as mainreflector. These configurations introduce additional complexity in several aspects respect to conventional dual offset reflectors, however they present a lot of degrees of freedom that can be used to improve the electrical performance of the antenna. The thesis is organized in four parts: the development of an analysis technique for dualreflectarray antennas, a preliminary validation of such methodology using equivalent reflector systems as reference antennas, a more rigorous validation of the software tool by manufacturing and testing a dual-reflectarray antenna demonstrator and the practical design of dual-reflectarray systems for some applications that show the potential of these kind of configurations to scan the beam and to generate contoured beams. In the first part, a general tool has been implemented to analyze high gain antennas which are constructed of two flat reflectarray structures. The classic reflectarray analysis based on MoM under local periodicity assumption is used for both sub and main reflectarrays, taking into account the incident angle on each reflectarray element. The incident field on the main reflectarray is computed taking into account the field radiated by all the elements on the sub-reflectarray.. Two approaches have been developed, one which employs a simple approximation to reduce the computer run time, and the other which does not, but offers in many cases, improved accuracy. The approximation is based on computing the reflected field on each element on the main reflectarray only once for all the fields radiated by the sub-reflectarray elements, assuming that the response will be the same because the only difference is a small variation on the angle of incidence. This approximation is very accurate when the reflectarray elements on the main reflectarray show a relatively small sensitivity to the angle of incidence. An extension of the analysis technique has been implemented to study dual-reflectarray antennas comprising a main reflectarray printed on a parabolic surface, or in general in a curved surface. In many applications of dual-reflectarray configurations, the reflectarray elements are in the near field of the feed-horn. To consider the near field radiated by the horn, the incident field on each reflectarray element is computed using a spherical mode expansion. In this region, the angles of incidence are moderately wide, and they are considered in the analysis of the reflectarray to better calculate the actual incident field on the sub-reflectarray elements. This technique increases the accuracy for the prediction of co- and cross-polar patterns and antenna gain respect to the case of using ideal feed models. In the second part, as a preliminary validation, the proposed analysis method has been used to design a dual-reflectarray antenna that emulates previous dual-reflector antennas in Ku and W-bands including a reflectarray as subreflector. The results for the dualreflectarray antenna compare very well with those of the parabolic reflector and reflectarray subreflector; radiation patterns, antenna gain and efficiency are practically the same when the main parabolic reflector is substituted by a flat reflectarray. The results show that the gain is only reduced by a few tenths of a dB as a result of the ohmic losses in the reflectarray. The phase adjustment on two surfaces provided by the dual-reflectarray configuration can be used to improve the antenna performance in some applications requiring multiple beams, beam scanning or shaped beams. Third, a very challenging dual-reflectarray antenna demonstrator has been designed, manufactured and tested for a more rigorous validation of the analysis technique presented. The proposed antenna configuration has the feed, the sub-reflectarray and the main-reflectarray in the near field one to each other, so that the conventional far field approximations are not suitable for the analysis of such antenna. This geometry is used as benchmarking for the proposed analysis tool in very stringent conditions. Some aspects of the proposed analysis technique that allow improving the accuracy of the analysis are also discussed. These improvements include a novel method to reduce the inherent cross polarization which is introduced mainly from grounded patch arrays. It has been checked that cross polarization in offset reflectarrays can be significantly reduced by properly adjusting the patch dimensions in the reflectarray in order to produce an overall cancellation of the cross-polarization. The dimensions of the patches are adjusted in order not only to provide the required phase-distribution to shape the beam, but also to exploit the crosses by zero of the cross-polarization components. The last part of the thesis deals with direct applications of the technique described. The technique presented is directly applicable to the design of contoured beam antennas for DBS applications, where the requirements of cross-polarisation are very stringent. The beam shaping is achieved by synthesithing the phase distribution on the main reflectarray while the sub-reflectarray emulates an equivalent hyperbolic subreflector. Dual-reflectarray antennas present also the ability to scan the beam over small angles about boresight. Two possible architectures for a Ku-band antenna are also described based on a dual planar reflectarray configuration that provides electronic beam scanning in a limited angular range. In the first architecture, the beam scanning is achieved by introducing a phase-control in the elements of the sub-reflectarray and the mainreflectarray is passive. A second alternative is also studied, in which the beam scanning is produced using 1-bit control on the main reflectarray, while a passive subreflectarray is designed to provide a large focal distance within a compact configuration. The system aims to develop a solution for bi-directional satellite links for emergency communications. In both proposed architectures, the objective is to provide a compact optics and simplicity to be folded and deployed.

Flexibility in Airline Business Models with Core Competence as an Indicator.

The airline industry is often unstable and unpredictable forcing airlines to restructure and create flexible strategies that can respond to external operating environmental changes. In turbulent and competitive environments, firms with higher flexibility perform better and the value of these flexibilities depends on factors of uncertainty in the competitive environment. A model is sought for and arrived at, that shows how an airline business model will function in an uncertain environment with the least reduction in business performance over time. An analysis of the business model flexibility of 17 Airlines from Asia, Europe and Oceania, that is done with core competence as the indicator reveals a picture of inconsistencies in the core competence strategy of certain airlines and the corresponding reduction in business performance. The performance variations are explained from a service oriented core competence strategy employed by airlines that ultimately enables them in having a flexible business model that not only increases business performance but also helps in reducing the uncertainties in the internal and external operating environments.

Simulation model for the study of overhead rail current collector systems dynamics, focused on the design of a new conductor rail

Overhead rigid conductor arrangements for current collection for railway traction have some advantages compared to other, more conventional, energy supply systems. They are simple, robust and easily maintained, not to mention their flexibility as to the required height for installation, which makes them particularly suitable for use in subway infrastructures. Nevertheless, due to the increasing speeds of new vehicles running on modern subway lines, a more efficient design is required for this kind of system. In this paper, the authors present a dynamic analysis of overhead conductor rail systems focused on the design of a new conductor profile with a dynamic behaviour superior to that of the system currently in use. This means that either an increase in running speed can be attained, which at present does not exceed 110 km/h, or an increase in the distance between the rigid catenary supports with the ensuing saving in installation costs. This study has been carried out using simulation techniques. The ANSYS programme has been used for the finite element modelling and the SIMPACK programme for the elastic multibody systems analysis.

Improved design of an overhead rail current conductor for application in underground lines

Overhead rail current collector systems for railway traction offer certain features, such as low installation height and reduced maintenance, which make them predominantly suitable for use in underground train infrastructures. Due to the increased demands of modern catenary systems and higher running speeds of new vehicles, a more capable design of the conductor rail is needed. A new overhead conductor rail has been developed and its design has been patented [13]. Modern simulation and modelling techniques were used in the development approach. The new conductor rail profile has a dynamic behaviour superior to that of the system currently in use. Its innovative design permits either an increase of catenary support spacing or a higher vehicle running speed. Both options ensure savings in installation or operating costs. The simulation model used to optimise the existing conductor rail profile included both a finite element model of the catenary and a three-dimensional multi-body system model of the pantograph. The contact force that appears between pantograph and catenary was obtained in simulation. A sensitivity analysis of the key parameters that influence in catenary dynamics was carried out, finally leading to the improved design.

Prototype emitter for use in subsurface drip irrigation: Manufacturing, hydraulic evaluation and experimental analyses

The current research aims to analyse theoretically and evaluate a self-manufactured simple design for subsurface drip irrigation (SDI) emitter to avoid root and soil intrusion. It was composed of three concentric cylindrical elements: an elastic silicone membrane; a polyethylene tube with two holes drilled on its wall for water discharge; and a vinyl polychloride protector system to wrap the other elements. The discharge of the emitter depends on the change in the membrane diameter when it is deformed by the water pressure. The study of the operation of this emitter is a new approach that considers mechanical and hydraulic principles. Thus, the estimation on the membrane deformation was based on classical mechanical stress theories in composite cylinders. The hydraulic principles considered the solid deformation due to force based on water pressure and the general Darcy–Weisbach head-loss equation. Twenty emitter units, with the selected design, were handcrafted in a lathe and were used in this study. The measured pressure/discharge relationship for the emitters showed good agreement with that calculated by the theoretical approach. The variation coefficient of the handcrafted emitters was high compared to commercial emitters. Results from field evaluations showed variable values for the relative flow variation, water emission uniformity and relative flow rate coefficients, but no emitter was obstructed. Therefore, the current emitter design could be suitable for SDI following further studies to develop a final prototype.

Social attitude toward sustainable development in 2025: A case for reinforcing scenario design

This paper shows the role that some foresight tools, such as scenario design, may play in exploring the future impacts of global challenges in our contemporary Society. Additionally, it provides some clues about how to reinforce scenario design so that it displays more in-depth analysis without losing its qualitative nature and communication advantages. Since its inception in the early seventies, scenario design has become one of the most popular foresight tools used in several fields of knowledge. Nevertheless, its wide acceptance has not been seconded by the urban planning academic and professional realm. In some instances, scenario design is just perceived as a story telling technique that generates oversimplified future visions without the support of rigorous and sound analysis. As a matter of fact, the potential of scenario design for providing more in-depth analysis and for connecting with quantitative methods has been generally missed, giving arguments away to its critics. Based on these premises, this document tries to prove the capability of scenario design to anticipate the impacts of complex global challenges and to do it in a more analytical way. These assumptions are tested through a scenario design exercise which explores the future evolution of the sustainable development paradigm (SD) and its implications in the Spanish urban development model. In order to reinforce the perception of scenario design as a useful and added value instrument to urban planners, three sets of implications –functional, parametric and spatial— are displayed to provide substantial and in-depth information for policy makers. This study shows some major findings. First, it is feasible to set up a systematic approach that provides anticipatory intelligence about future disruptive events that may affect the natural environment and socioeconomic fabric of a given territory. Second, there are opportunities for innovating in the Spanish urban planning processes and city governance models. Third, as a foresight tool, scenario design can be substantially reinforced if proper efforts are made to display functional, parametric and spatial implications generated by the scenarios. Fourth, the study confirms that foresight offers interesting opportunities for urban planners, such as anticipating changes, formulating visions, fostering participation and building networks

X-parameters based analytical design of non-linear microwave circuits Application to oscillator design

Resumen El diseño clásico de circuitos de microondas se basa fundamentalmente en el uso de los parámetros s, debido a su capacidad para caracterizar de forma exitosa el comportamiento de cualquier circuito lineal. La relación existente entre los parámetros s con los sistemas de medida actuales y con las herramientas de simulación lineal han facilitado su éxito y su uso extensivo tanto en el diseño como en la caracterización de circuitos y subsistemas de microondas. Sin embargo, a pesar de la gran aceptación de los parámetros s en la comunidad de microondas, el principal inconveniente de esta formulación reside en su limitación para predecir el comportamiento de sistemas no lineales reales. En la actualidad, uno de los principales retos de los diseñadores de microondas es el desarrollo de un contexto análogo que permita integrar tanto el modelado no lineal, como los sistemas de medidas de gran señal y los entornos de simulación no lineal, con el objetivo de extender las capacidades de los parámetros s a regímenes de operación en gran señal y por tanto, obtener una infraestructura que permita tanto la caracterización como el diseño de circuitos no lineales de forma fiable y eficiente. De acuerdo a esta filosofía, en los últimos años se han desarrollado diferentes propuestas como los parámetros X, de Agilent Technologies, o el modelo de Cardiff que tratan de proporcionar esta plataforma común en el ámbito de gran señal. Dentro de este contexto, uno de los objetivos de la presente Tesis es el análisis de la viabilidad del uso de los parámetros X en el diseño y simulación de osciladores para transceptores de microondas. Otro aspecto relevante en el análisis y diseño de circuitos lineales de microondas es la disposición de métodos analíticos sencillos, basados en los parámetros s del transistor, que permitan la obtención directa y rápida de las impedancias de carga y fuente necesarias para cumplir las especificaciones de diseño requeridas en cuanto a ganancia, potencia de salida, eficiencia o adaptación de entrada y salida, así como la determinación analítica de parámetros de diseño clave como el factor de estabilidad o los contornos de ganancia de potencia. Por lo tanto, el desarrollo de una formulación de diseño analítico, basada en los parámetros X y similar a la existente en pequeña señal, permitiría su uso en aplicaciones no lineales y supone un nuevo reto que se va a afrontar en este trabajo. Por tanto, el principal objetivo de la presente Tesis consistiría en la elaboración de una metodología analítica basada en el uso de los parámetros X para el diseño de circuitos no lineales que jugaría un papel similar al que juegan los parámetros s en el diseño de circuitos lineales de microondas. Dichos métodos de diseño analíticos permitirían una mejora significativa en los actuales procedimientos de diseño disponibles en gran señal, así como una reducción considerable en el tiempo de diseño, lo que permitiría la obtención de técnicas mucho más eficientes. Abstract In linear world, classical microwave circuit design relies on the s-parameters due to its capability to successfully characterize the behavior of any linear circuit. Thus the direct use of s-parameters in measurement systems and in linear simulation analysis tools, has facilitated its extensive use and success in the design and characterization of microwave circuits and subsystems. Nevertheless, despite the great success of s-parameters in the microwave community, the main drawback of this formulation is its limitation in the behavior prediction of real non-linear systems. Nowadays, the challenge of microwave designers is the development of an analogue framework that allows to integrate non-linear modeling, large-signal measurement hardware and non-linear simulation environment in order to extend s-parameters capabilities to non-linear regimen and thus, provide the infrastructure for non-linear design and test in a reliable and efficient way. Recently, different attempts with the aim to provide this common platform have been introduced, as the Cardiff approach and the Agilent X-parameters. Hence, this Thesis aims to demonstrate the X-parameter capability to provide this non-linear design and test framework in CAD-based oscillator context. Furthermore, the classical analysis and design of linear microwave transistorbased circuits is based on the development of simple analytical approaches, involving the transistor s-parameters, that are able to quickly provide an analytical solution for the input/output transistor loading conditions as well as analytically determine fundamental parameters as the stability factor, the power gain contours or the input/ output match. Hence, the development of similar analytical design tools that are able to extend s-parameters capabilities in small-signal design to non-linear ap- v plications means a new challenge that is going to be faced in the present work. Therefore, the development of an analytical design framework, based on loadindependent X-parameters, constitutes the core of this Thesis. These analytical nonlinear design approaches would enable to significantly improve current large-signal design processes as well as dramatically decrease the required design time and thus, obtain more efficient approaches.

Analytic free-form lens design in 3D: coupling three ray sets using two lens surfaces

The two-dimensional analytic optics design method presented in a previous paper [Opt. Express 20, 5576–5585 (2012)] is extended in this work to the three-dimensional case, enabling the coupling of three ray sets with two free-form lens surfaces. Fermat’s principle is used to deduce additional sets of functional differential equations which make it possible to calculate the lens surfaces. Ray tracing simulations demonstrate the excellent imaging performance of the resulting free-form lenses described by more than 100 coefficients.

Impact of knowledge brokering on performance heterogeneity among business models

Purpose – The strategic management literature lacks a comprehensive explanation as to why seemingly similar business models in the same industry perform differently. This paper strives to explain this phenomenon. Design/methodology/approach – The model is conceptualized and accompanied by a case study on the airline industry to explain knowledge brokerage that creates value from the effective utilization of knowledge resources acquired from intra- and inter-firm environments. Findings – The model explains a cyclical view of business model flexibility in which the knowledge-based resource accumulation of the business model is spread across the intra- and inter-firm environments. Knowledge brokerage strategies from the inter- and intra-firm environments result in improved performance of the business model. The flexibility that the business model acquires is determined by how efficiently resource accumulation is aligned with its external environment. Originality/value – The paper effectively integrates the concepts of knowledge brokerage and business models from a resource accumulation-based view and simultaneously arrives at the performance heterogeneity of seemingly similar business models within the same industry. It has performance implications for firms that start out without any distinct resources of their own, or that use an imitated business model, to attain better performance through business model evolution aligned with successful knowledge brokerage strategies. It adds to the resource accumulation literature by explaining how resources can be effectively acquired to create value.

Analytic free-form lens design for tracking integration in concentrating photovoltaics

In this work the concept of tracking integration in concentrating photovoltaics (CPV) is revisited and developed further. With respect to conventional CPV, tracking integration eliminates the clear separation between stationary units of optics and solar cells, and external solar trackers. This approach is capable of further increasing the concentration ratio and makes high concentrating photovoltaics (> 500x) available for single-axis tracker installations. The reduced external solar tracking effort enables possibly cheaper and more compact installations. Our proposed optical system uses two laterally moving plano-convex lenses to achieve high concentration over a wide angular range of ±24°. The lateral movement allows to combine both steering and concentration of the incident direct sun light. Given the specific symmetry conditions of the underlying optical design problem, rotational symmetric lenses are not ideal for this application. For this type of design problems, a new free-form optics design method presented in previous papers perfectly matches the symmetry. It is derived directly from Fermat's principle, leading to sets of functional differential equations allowing the successive calculation of the Taylor series coeficients of each implicit surface function up to very high orders. For optical systems designed for wide field of view and with clearly separated optical surfaces, this new analytic design method has potential application in both fields of nonimaging and imaging optics.

Side-Channel Attack Protection Techniques in FPGA Systems using Enhanced Dual-Rail Solutions

Esta tesis doctoral se centra principalmente en técnicas de ataque y contramedidas relacionadas con ataques de canal lateral (SCA por sus siglas en inglés), que han sido propuestas dentro del campo de investigación académica desde hace 17 años. Las investigaciones relacionadas han experimentado un notable crecimiento en las últimas décadas, mientras que los diseños enfocados en la protección sólida y eficaz contra dichos ataques aún se mantienen como un tema de investigación abierto, en el que se necesitan iniciativas más confiables para la protección de la información persona de empresa y de datos nacionales. El primer uso documentado de codificación secreta se remonta a alrededor de 1700 B.C., cuando los jeroglíficos del antiguo Egipto eran descritos en las inscripciones. La seguridad de la información siempre ha supuesto un factor clave en la transmisión de datos relacionados con inteligencia diplomática o militar. Debido a la evolución rápida de las técnicas modernas de comunicación, soluciones de cifrado se incorporaron por primera vez para garantizar la seguridad, integridad y confidencialidad de los contextos de transmisión a través de cables sin seguridad o medios inalámbricos. Debido a las restricciones de potencia de cálculo antes de la era del ordenador, la técnica de cifrado simple era un método más que suficiente para ocultar la información. Sin embargo, algunas vulnerabilidades algorítmicas pueden ser explotadas para restaurar la regla de codificación sin mucho esfuerzo. Esto ha motivado nuevas investigaciones en el área de la criptografía, con el fin de proteger el sistema de información ante sofisticados algoritmos. Con la invención de los ordenadores se ha acelerado en gran medida la implementación de criptografía segura, que ofrece resistencia eficiente encaminada a obtener mayores capacidades de computación altamente reforzadas. Igualmente, sofisticados cripto-análisis han impulsado las tecnologías de computación. Hoy en día, el mundo de la información ha estado involucrado con el campo de la criptografía, enfocada a proteger cualquier campo a través de diversas soluciones de cifrado. Estos enfoques se han fortalecido debido a la unificación optimizada de teorías matemáticas modernas y prácticas eficaces de hardware, siendo posible su implementación en varias plataformas (microprocesador, ASIC, FPGA, etc.). Las necesidades y requisitos de seguridad en la industria son las principales métricas de conducción en el diseño electrónico, con el objetivo de promover la fabricación de productos de gran alcance sin sacrificar la seguridad de los clientes. Sin embargo, una vulnerabilidad en la implementación práctica encontrada por el Prof. Paul Kocher, et al en 1996 implica que un circuito digital es inherentemente vulnerable a un ataque no convencional, lo cual fue nombrado posteriormente como ataque de canal lateral, debido a su fuente de análisis. Sin embargo, algunas críticas sobre los algoritmos criptográficos teóricamente seguros surgieron casi inmediatamente después de este descubrimiento. En este sentido, los circuitos digitales consisten típicamente en un gran número de celdas lógicas fundamentales (como MOS - Metal Oxide Semiconductor), construido sobre un sustrato de silicio durante la fabricación. La lógica de los circuitos se realiza en función de las innumerables conmutaciones de estas células. Este mecanismo provoca inevitablemente cierta emanación física especial que puede ser medida y correlacionada con el comportamiento interno del circuito. SCA se puede utilizar para revelar datos confidenciales (por ejemplo, la criptografía de claves), analizar la arquitectura lógica, el tiempo e incluso inyectar fallos malintencionados a los circuitos que se implementan en sistemas embebidos, como FPGAs, ASICs, o tarjetas inteligentes. Mediante el uso de la comparación de correlación entre la cantidad de fuga estimada y las fugas medidas de forma real, información confidencial puede ser reconstruida en mucho menos tiempo y computación. Para ser precisos, SCA básicamente cubre una amplia gama de tipos de ataques, como los análisis de consumo de energía y radiación ElectroMagnética (EM). Ambos se basan en análisis estadístico y, por lo tanto, requieren numerosas muestras. Los algoritmos de cifrado no están intrínsecamente preparados para ser resistentes ante SCA. Es por ello que se hace necesario durante la implementación de circuitos integrar medidas que permitan camuflar las fugas a través de "canales laterales". Las medidas contra SCA están evolucionando junto con el desarrollo de nuevas técnicas de ataque, así como la continua mejora de los dispositivos electrónicos. Las características físicas requieren contramedidas sobre la capa física, que generalmente se pueden clasificar en soluciones intrínsecas y extrínsecas. Contramedidas extrínsecas se ejecutan para confundir la fuente de ataque mediante la integración de ruido o mala alineación de la actividad interna. Comparativamente, las contramedidas intrínsecas están integradas en el propio algoritmo, para modificar la aplicación con el fin de minimizar las fugas medibles, o incluso hacer que dichas fugas no puedan ser medibles. Ocultación y Enmascaramiento son dos técnicas típicas incluidas en esta categoría. Concretamente, el enmascaramiento se aplica a nivel algorítmico, para alterar los datos intermedios sensibles con una máscara de manera reversible. A diferencia del enmascaramiento lineal, las operaciones no lineales que ampliamente existen en criptografías modernas son difíciles de enmascarar. Dicho método de ocultación, que ha sido verificado como una solución efectiva, comprende principalmente la codificación en doble carril, que está ideado especialmente para aplanar o eliminar la fuga dependiente de dato en potencia o en EM. En esta tesis doctoral, además de la descripción de las metodologías de ataque, se han dedicado grandes esfuerzos sobre la estructura del prototipo de la lógica propuesta, con el fin de realizar investigaciones enfocadas a la seguridad sobre contramedidas de arquitectura a nivel lógico. Una característica de SCA reside en el formato de las fuentes de fugas. Un típico ataque de canal lateral se refiere al análisis basado en la potencia, donde la capacidad fundamental del transistor MOS y otras capacidades parásitas son las fuentes esenciales de fugas. Por lo tanto, una lógica robusta resistente a SCA debe eliminar o mitigar las fugas de estas micro-unidades, como las puertas lógicas básicas, los puertos I/O y las rutas. Las herramientas EDA proporcionadas por los vendedores manipulan la lógica desde un nivel más alto, en lugar de realizarlo desde el nivel de puerta, donde las fugas de canal lateral se manifiestan. Por lo tanto, las implementaciones clásicas apenas satisfacen estas necesidades e inevitablemente atrofian el prototipo. Por todo ello, la implementación de un esquema de diseño personalizado y flexible ha de ser tomado en cuenta. En esta tesis se presenta el diseño y la implementación de una lógica innovadora para contrarrestar SCA, en la que se abordan 3 aspectos fundamentales: I. Se basa en ocultar la estrategia sobre el circuito en doble carril a nivel de puerta para obtener dinámicamente el equilibrio de las fugas en las capas inferiores; II. Esta lógica explota las características de la arquitectura de las FPGAs, para reducir al mínimo el gasto de recursos en la implementación; III. Se apoya en un conjunto de herramientas asistentes personalizadas, incorporadas al flujo genérico de diseño sobre FPGAs, con el fin de manipular los circuitos de forma automática. El kit de herramientas de diseño automático es compatible con la lógica de doble carril propuesta, para facilitar la aplicación práctica sobre la familia de FPGA del fabricante Xilinx. En este sentido, la metodología y las herramientas son flexibles para ser extendido a una amplia gama de aplicaciones en las que se desean obtener restricciones mucho más rígidas y sofisticadas a nivel de puerta o rutado. En esta tesis se realiza un gran esfuerzo para facilitar el proceso de implementación y reparación de lógica de doble carril genérica. La viabilidad de las soluciones propuestas es validada mediante la selección de algoritmos criptográficos ampliamente utilizados, y su evaluación exhaustiva en comparación con soluciones anteriores. Todas las propuestas están respaldadas eficazmente a través de ataques experimentales con el fin de validar las ventajas de seguridad del sistema. El presente trabajo de investigación tiene la intención de cerrar la brecha entre las barreras de implementación y la aplicación efectiva de lógica de doble carril. En esencia, a lo largo de esta tesis se describirá un conjunto de herramientas de implementación para FPGAs que se han desarrollado para trabajar junto con el flujo de diseño genérico de las mismas, con el fin de lograr crear de forma innovadora la lógica de doble carril. Un nuevo enfoque en el ámbito de la seguridad en el cifrado se propone para obtener personalización, automatización y flexibilidad en el prototipo de circuito de bajo nivel con granularidad fina. Las principales contribuciones del presente trabajo de investigación se resumen brevemente a continuación: Lógica de Precharge Absorbed-DPL logic: El uso de la conversión de netlist para reservar LUTs libres para ejecutar la señal de precharge y Ex en una lógica DPL. Posicionamiento entrelazado Row-crossed con pares idénticos de rutado en redes de doble carril, lo que ayuda a aumentar la resistencia frente a la medición EM selectiva y mitigar los impactos de las variaciones de proceso. Ejecución personalizada y herramientas de conversión automática para la generación de redes idénticas para la lógica de doble carril propuesta. (a) Para detectar y reparar conflictos en las conexiones; (b) Detectar y reparar las rutas asimétricas. (c) Para ser utilizado en otras lógicas donde se requiere un control estricto de las interconexiones en aplicaciones basadas en Xilinx. Plataforma CPA de pruebas personalizadas para el análisis de EM y potencia, incluyendo la construcción de dicha plataforma, el método de medición y análisis de los ataques. Análisis de tiempos para cuantificar los niveles de seguridad. División de Seguridad en la conversión parcial de un sistema de cifrado complejo para reducir los costes de la protección. Prueba de concepto de un sistema de calefacción auto-adaptativo para mitigar los impactos eléctricos debido a la variación del proceso de silicio de manera dinámica. La presente tesis doctoral se encuentra organizada tal y como se detalla a continuación: En el capítulo 1 se abordan los fundamentos de los ataques de canal lateral, que abarca desde conceptos básicos de teoría de modelos de análisis, además de la implementación de la plataforma y la ejecución de los ataques. En el capítulo 2 se incluyen las estrategias de resistencia SCA contra los ataques de potencia diferencial y de EM. Además de ello, en este capítulo se propone una lógica en doble carril compacta y segura como contribución de gran relevancia, así como también se presentará la transformación lógica basada en un diseño a nivel de puerta. Por otra parte, en el Capítulo 3 se abordan los desafíos relacionados con la implementación de lógica en doble carril genérica. Así mismo, se describirá un flujo de diseño personalizado para resolver los problemas de aplicación junto con una herramienta de desarrollo automático de aplicaciones propuesta, para mitigar las barreras de diseño y facilitar los procesos. En el capítulo 4 se describe de forma detallada la elaboración e implementación de las herramientas propuestas. Por otra parte, la verificación y validaciones de seguridad de la lógica propuesta, así como un sofisticado experimento de verificación de la seguridad del rutado, se describen en el capítulo 5. Por último, un resumen de las conclusiones de la tesis y las perspectivas como líneas futuras se incluyen en el capítulo 6. Con el fin de profundizar en el contenido de la tesis doctoral, cada capítulo se describe de forma más detallada a continuación: En el capítulo 1 se introduce plataforma de implementación hardware además las teorías básicas de ataque de canal lateral, y contiene principalmente: (a) La arquitectura genérica y las características de la FPGA a utilizar, en particular la Xilinx Virtex-5; (b) El algoritmo de cifrado seleccionado (un módulo comercial Advanced Encryption Standard (AES)); (c) Los elementos esenciales de los métodos de canal lateral, que permiten revelar las fugas de disipación correlacionadas con los comportamientos internos; y el método para recuperar esta relación entre las fluctuaciones físicas en los rastros de canal lateral y los datos internos procesados; (d) Las configuraciones de las plataformas de pruebas de potencia / EM abarcadas dentro de la presente tesis. El contenido de esta tesis se amplia y profundiza a partir del capítulo 2, en el cual se abordan varios aspectos claves. En primer lugar, el principio de protección de la compensación dinámica de la lógica genérica de precarga de doble carril (Dual-rail Precharge Logic-DPL) se explica mediante la descripción de los elementos compensados a nivel de puerta. En segundo lugar, la lógica PA-DPL es propuesta como aportación original, detallando el protocolo de la lógica y un caso de aplicación. En tercer lugar, dos flujos de diseño personalizados se muestran para realizar la conversión de doble carril. Junto con ello, se aclaran las definiciones técnicas relacionadas con la manipulación por encima de la netlist a nivel de LUT. Finalmente, una breve discusión sobre el proceso global se aborda en la parte final del capítulo. El Capítulo 3 estudia los principales retos durante la implementación de DPLs en FPGAs. El nivel de seguridad de las soluciones de resistencia a SCA encontradas en el estado del arte se ha degenerado debido a las barreras de implantación a través de herramientas EDA convencionales. En el escenario de la arquitectura FPGA estudiada, se discuten los problemas de los formatos de doble carril, impactos parásitos, sesgo tecnológico y la viabilidad de implementación. De acuerdo con estas elaboraciones, se plantean dos problemas: Cómo implementar la lógica propuesta sin penalizar los niveles de seguridad, y cómo manipular un gran número de celdas y automatizar el proceso. El PA-DPL propuesto en el capítulo 2 se valida con una serie de iniciativas, desde características estructurales como doble carril entrelazado o redes de rutado clonadas, hasta los métodos de aplicación tales como las herramientas de personalización y automatización de EDA. Por otra parte, un sistema de calefacción auto-adaptativo es representado y aplicado a una lógica de doble núcleo, con el fin de ajustar alternativamente la temperatura local para equilibrar los impactos negativos de la variación del proceso durante la operación en tiempo real. El capítulo 4 se centra en los detalles de la implementación del kit de herramientas. Desarrollado sobre una API third-party, el kit de herramientas personalizado es capaz de manipular los elementos de la lógica de circuito post P&R ncd (una versión binaria ilegible del xdl) convertido al formato XDL Xilinx. El mecanismo y razón de ser del conjunto de instrumentos propuestos son cuidadosamente descritos, que cubre la detección de enrutamiento y los enfoques para la reparación. El conjunto de herramientas desarrollado tiene como objetivo lograr redes de enrutamiento estrictamente idénticos para la lógica de doble carril, tanto para posicionamiento separado como para el entrelazado. Este capítulo particularmente especifica las bases técnicas para apoyar las implementaciones en los dispositivos de Xilinx y su flexibilidad para ser utilizado sobre otras aplicaciones. El capítulo 5 se enfoca en la aplicación de los casos de estudio para la validación de los grados de seguridad de la lógica propuesta. Se discuten los problemas técnicos detallados durante la ejecución y algunas nuevas técnicas de implementación. (a) Se discute el impacto en el proceso de posicionamiento de la lógica utilizando el kit de herramientas propuesto. Diferentes esquemas de implementación, tomando en cuenta la optimización global en seguridad y coste, se verifican con los experimentos con el fin de encontrar los planes de posicionamiento y reparación optimizados; (b) las validaciones de seguridad se realizan con los métodos de correlación y análisis de tiempo; (c) Una táctica asintótica se aplica a un núcleo AES sobre BCDL estructurado para validar de forma sofisticada el impacto de enrutamiento sobre métricas de seguridad; (d) Los resultados preliminares utilizando el sistema de calefacción auto-adaptativa sobre la variación del proceso son mostrados; (e) Se introduce una aplicación práctica de las herramientas para un diseño de cifrado completa. Capítulo 6 incluye el resumen general del trabajo presentado dentro de esta tesis doctoral. Por último, una breve perspectiva del trabajo futuro se expone, lo que puede ampliar el potencial de utilización de las contribuciones de esta tesis a un alcance más allá de los dominios de la criptografía en FPGAs. ABSTRACT This PhD thesis mainly concentrates on countermeasure techniques related to the Side Channel Attack (SCA), which has been put forward to academic exploitations since 17 years ago. The related research has seen a remarkable growth in the past decades, while the design of solid and efficient protection still curiously remain as an open research topic where more reliable initiatives are required for personal information privacy, enterprise and national data protections. The earliest documented usage of secret code can be traced back to around 1700 B.C., when the hieroglyphs in ancient Egypt are scribed in inscriptions. Information security always gained serious attention from diplomatic or military intelligence transmission. Due to the rapid evolvement of modern communication technique, crypto solution was first incorporated by electronic signal to ensure the confidentiality, integrity, availability, authenticity and non-repudiation of the transmitted contexts over unsecure cable or wireless channels. Restricted to the computation power before computer era, simple encryption tricks were practically sufficient to conceal information. However, algorithmic vulnerabilities can be excavated to restore the encoding rules with affordable efforts. This fact motivated the development of modern cryptography, aiming at guarding information system by complex and advanced algorithms. The appearance of computers has greatly pushed forward the invention of robust cryptographies, which efficiently offers resistance relying on highly strengthened computing capabilities. Likewise, advanced cryptanalysis has greatly driven the computing technologies in turn. Nowadays, the information world has been involved into a crypto world, protecting any fields by pervasive crypto solutions. These approaches are strong because of the optimized mergence between modern mathematical theories and effective hardware practices, being capable of implement crypto theories into various platforms (microprocessor, ASIC, FPGA, etc). Security needs from industries are actually the major driving metrics in electronic design, aiming at promoting the construction of systems with high performance without sacrificing security. Yet a vulnerability in practical implementation found by Prof. Paul Kocher, et al in 1996 implies that modern digital circuits are inherently vulnerable to an unconventional attack approach, which was named as side-channel attack since then from its analysis source. Critical suspicions to theoretically sound modern crypto algorithms surfaced almost immediately after this discovery. To be specifically, digital circuits typically consist of a great number of essential logic elements (as MOS - Metal Oxide Semiconductor), built upon a silicon substrate during the fabrication. Circuit logic is realized relying on the countless switch actions of these cells. This mechanism inevitably results in featured physical emanation that can be properly measured and correlated with internal circuit behaviors. SCAs can be used to reveal the confidential data (e.g. crypto-key), analyze the logic architecture, timing and even inject malicious faults to the circuits that are implemented in hardware system, like FPGA, ASIC, smart Card. Using various comparison solutions between the predicted leakage quantity and the measured leakage, secrets can be reconstructed at much less expense of time and computation. To be precisely, SCA basically encloses a wide range of attack types, typically as the analyses of power consumption or electromagnetic (EM) radiation. Both of them rely on statistical analyses, and hence require a number of samples. The crypto algorithms are not intrinsically fortified with SCA-resistance. Because of the severity, much attention has to be taken into the implementation so as to assemble countermeasures to camouflage the leakages via "side channels". Countermeasures against SCA are evolving along with the development of attack techniques. The physical characteristics requires countermeasures over physical layer, which can be generally classified into intrinsic and extrinsic vectors. Extrinsic countermeasures are executed to confuse the attacker by integrating noise, misalignment to the intra activities. Comparatively, intrinsic countermeasures are built into the algorithm itself, to modify the implementation for minimizing the measurable leakage, or making them not sensitive any more. Hiding and Masking are two typical techniques in this category. Concretely, masking applies to the algorithmic level, to alter the sensitive intermediate values with a mask in reversible ways. Unlike the linear masking, non-linear operations that widely exist in modern cryptographies are difficult to be masked. Approved to be an effective counter solution, hiding method mainly mentions dual-rail logic, which is specially devised for flattening or removing the data-dependent leakage in power or EM signatures. In this thesis, apart from the context describing the attack methodologies, efforts have also been dedicated to logic prototype, to mount extensive security investigations to countermeasures on logic-level. A characteristic of SCA resides on the format of leak sources. Typical side-channel attack concerns the power based analysis, where the fundamental capacitance from MOS transistors and other parasitic capacitances are the essential leak sources. Hence, a robust SCA-resistant logic must eliminate or mitigate the leakages from these micro units, such as basic logic gates, I/O ports and routings. The vendor provided EDA tools manipulate the logic from a higher behavioral-level, rather than the lower gate-level where side-channel leakage is generated. So, the classical implementations barely satisfy these needs and inevitably stunt the prototype. In this case, a customized and flexible design scheme is appealing to be devised. This thesis profiles an innovative logic style to counter SCA, which mainly addresses three major aspects: I. The proposed logic is based on the hiding strategy over gate-level dual-rail style to dynamically overbalance side-channel leakage from lower circuit layer; II. This logic exploits architectural features of modern FPGAs, to minimize the implementation expenses; III. It is supported by a set of assistant custom tools, incorporated by the generic FPGA design flow, to have circuit manipulations in an automatic manner. The automatic design toolkit supports the proposed dual-rail logic, facilitating the practical implementation on Xilinx FPGA families. While the methodologies and the tools are flexible to be expanded to a wide range of applications where rigid and sophisticated gate- or routing- constraints are desired. In this thesis a great effort is done to streamline the implementation workflow of generic dual-rail logic. The feasibility of the proposed solutions is validated by selected and widely used crypto algorithm, for thorough and fair evaluation w.r.t. prior solutions. All the proposals are effectively verified by security experiments. The presented research work attempts to solve the implementation troubles. The essence that will be formalized along this thesis is that a customized execution toolkit for modern FPGA systems is developed to work together with the generic FPGA design flow for creating innovative dual-rail logic. A method in crypto security area is constructed to obtain customization, automation and flexibility in low-level circuit prototype with fine-granularity in intractable routings. Main contributions of the presented work are summarized next: Precharge Absorbed-DPL logic: Using the netlist conversion to reserve free LUT inputs to execute the Precharge and Ex signal in a dual-rail logic style. A row-crossed interleaved placement method with identical routing pairs in dual-rail networks, which helps to increase the resistance against selective EM measurement and mitigate the impacts from process variations. Customized execution and automatic transformation tools for producing identical networks for the proposed dual-rail logic. (a) To detect and repair the conflict nets; (b) To detect and repair the asymmetric nets. (c) To be used in other logics where strict network control is required in Xilinx scenario. Customized correlation analysis testbed for EM and power attacks, including the platform construction, measurement method and attack analysis. A timing analysis based method for quantifying the security grades. A methodology of security partitions of complex crypto systems for reducing the protection cost. A proof-of-concept self-adaptive heating system to mitigate electrical impacts over process variations in dynamic dual-rail compensation manner. The thesis chapters are organized as follows: Chapter 1 discusses the side-channel attack fundamentals, which covers from theoretic basics to analysis models, and further to platform setup and attack execution. Chapter 2 centers to SCA-resistant strategies against generic power and EM attacks. In this chapter, a major contribution, a compact and secure dual-rail logic style, will be originally proposed. The logic transformation based on bottom-layer design will be presented. Chapter 3 is scheduled to elaborate the implementation challenges of generic dual-rail styles. A customized design flow to solve the implementation problems will be described along with a self-developed automatic implementation toolkit, for mitigating the design barriers and facilitating the processes. Chapter 4 will originally elaborate the tool specifics and construction details. The implementation case studies and security validations for the proposed logic style, as well as a sophisticated routing verification experiment, will be described in Chapter 5. Finally, a summary of thesis conclusions and perspectives for future work are included in Chapter 5. To better exhibit the thesis contents, each chapter is further described next: Chapter 1 provides the introduction of hardware implementation testbed and side-channel attack fundamentals, and mainly contains: (a) The FPGA generic architecture and device features, particularly of Virtex-5 FPGA; (b) The selected crypto algorithm - a commercially and extensively used Advanced Encryption Standard (AES) module - is detailed; (c) The essentials of Side-Channel methods are profiled. It reveals the correlated dissipation leakage to the internal behaviors, and the method to recover this relationship between the physical fluctuations in side-channel traces and the intra processed data; (d) The setups of the power/EM testing platforms enclosed inside the thesis work are given. The content of this thesis is expanded and deepened from chapter 2, which is divided into several aspects. First, the protection principle of dynamic compensation of the generic dual-rail precharge logic is explained by describing the compensated gate-level elements. Second, the novel DPL is originally proposed by detailing the logic protocol and an implementation case study. Third, a couple of custom workflows are shown next for realizing the rail conversion. Meanwhile, the technical definitions that are about to be manipulated above LUT-level netlist are clarified. A brief discussion about the batched process is given in the final part. Chapter 3 studies the implementation challenges of DPLs in FPGAs. The security level of state-of-the-art SCA-resistant solutions are decreased due to the implementation barriers using conventional EDA tools. In the studied FPGA scenario, problems are discussed from dual-rail format, parasitic impact, technological bias and implementation feasibility. According to these elaborations, two problems arise: How to implement the proposed logic without crippling the security level; and How to manipulate a large number of cells and automate the transformation. The proposed PA-DPL in chapter 2 is legalized with a series of initiatives, from structures to implementation methods. Furthermore, a self-adaptive heating system is depicted and implemented to a dual-core logic, assumed to alternatively adjust local temperature for balancing the negative impacts from silicon technological biases on real-time. Chapter 4 centers to the toolkit system. Built upon a third-party Application Program Interface (API) library, the customized toolkit is able to manipulate the logic elements from post P&R circuit (an unreadable binary version of the xdl one) converted to Xilinx xdl format. The mechanism and rationale of the proposed toolkit are carefully convoyed, covering the routing detection and repairing approaches. The developed toolkit aims to achieve very strictly identical routing networks for dual-rail logic both for separate and interleaved placement. This chapter particularly specifies the technical essentials to support the implementations in Xilinx devices and the flexibility to be expanded to other applications. Chapter 5 focuses on the implementation of the case studies for validating the security grades of the proposed logic style from the proposed toolkit. Comprehensive implementation techniques are discussed. (a) The placement impacts using the proposed toolkit are discussed. Different execution schemes, considering the global optimization in security and cost, are verified with experiments so as to find the optimized placement and repair schemes; (b) Security validations are realized with correlation, timing methods; (c) A systematic method is applied to a BCDL structured module to validate the routing impact over security metric; (d) The preliminary results using the self-adaptive heating system over process variation is given; (e) A practical implementation of the proposed toolkit to a large design is introduced. Chapter 6 includes the general summary of the complete work presented inside this thesis. Finally, a brief perspective for the future work is drawn which might expand the potential utilization of the thesis contributions to a wider range of implementation domains beyond cryptography on FPGAs.

Comparison of micrometeorological techinques for estimating ammonia emission from covered slurry storage and land spreading of cattle slurry

The micrometeorological mass-balance integrated horizontal flux (IHF) technique has been commonly employed for measuring ammonia (NH3) emissions inon-field experiments. However, the inverse-dispersion modeling technique, such as the backward Lagrangian stochastic (bLS) modeling approach, is currently highlighted as offering flexibility in plot design and requiring a minimum number of samplers (Ro et al., 2013). The objective of this study was to make a comparison between the bLS technique with the IHF technique for estimating NH3 emission from flexible bag storage and following landspreading of dairy cattle slurry. Moreover, considering that NH3 emission in storage could have been non uniform, the effect on bLS estimates of a single point and multiple downwind concentration measurements was tested, as proposed by Sanz et al. (2010).

CompactRIO: advanced data acquisition systems integration in CODAC Core System

Las herramientas de configuración basadas en lenguajes de alto nivel como LabVIEW permiten el desarrollo de sistemas de adquisición de datos basados en hardware reconfigurable FPGA muy complejos en un breve periodo de tiempo. La estandarización del ciclo de diseño hardware/software y la utilización de herramientas como EPICS facilita su integración con la plataforma de adquisición y control ITER CODAC CORE SYSTEM (CCS) basada en Linux. En este proyecto se propondrá una metodología que simplificará el ciclo completo de integración de plataformas novedosas, como cRIO, en las que el funcionamiento del hardware de adquisición puede ser modificado por el usuario para que éste se amolde a sus requisitos específicos. El objetivo principal de este proyecto fin de master es realizar la integración de un sistema cRIO NI9159 y diferentes módulos de E/S analógica y digital en EPICS y en CODAC CORE SYSTEM (CCS). Este último consiste en un conjunto de herramientas software que simplifican la integración de los sistemas de instrumentación y control del experimento ITER. Para cumplir el objetivo se realizarán las siguientes tareas: • Desarrollo de un sistema de adquisición de datos basado en FPGA con la plataforma hardware CompactRIO. En esta tarea se realizará la configuración del sistema y la implementación en LabVIEW para FPGA del hardware necesario para comunicarse con los módulos: NI9205, NI9264, NI9401.NI9477, NI9426, NI9425 y NI9476 • Implementación de un driver software utilizando la metodología de AsynDriver para integración del cRIO con EPICS. Esta tarea requiere definir todos los records necesarios que exige EPICS y crear las interfaces adecuadas que permitirán comunicarse con el hardware. • Implementar la descripción del sistema cRIO y del driver EPICS en el sistema de descripción de plantas de ITER llamado SDD. Esto automatiza la creación de las aplicaciones de EPICS que se denominan IOCs. SUMMARY The configuration tools based in high-level programing languages like LabVIEW allows the development of high complex data acquisition systems based on reconfigurable hardware FPGA in a short time period. The standardization of the hardware/software design cycle and the use of tools like EPICS ease the integration with the data acquisition and control platform of ITER, the CODAC Core System based on Linux. In this project a methodology is proposed in order to simplify the full integration cycle of new platforms like CompactRIO (cRIO), in which the data acquisition functionality can be reconfigured by the user to fits its concrete requirements. The main objective of this MSc final project is to develop the integration of a cRIO NI-9159 and its different analog and digital Input/Output modules with EPICS in a CCS. The CCS consists of a set of software tools that simplifies the integration of instrumentation and control systems in the International Thermonuclear Reactor (ITER) experiment. To achieve such goal the following tasks are carried out: • Development of a DAQ system based on FPGA using the cRIO hardware platform. This task comprehends the configuration of the system and the implementation of the mandatory hardware to communicate to the I/O adapter modules NI9205, NI9264, NI9401, NI9477, NI9426, NI9425 y NI9476 using LabVIEW for FPGA. • Implementation of a software driver using the asynDriver methodology to integrate such cRIO system with EPICS. This task requires the definition of the necessary EPICS records and the creation of the appropriate interfaces that allow the communication with the hardware. • Develop the cRIO system’s description and the EPICS driver in the ITER plant description tool named SDD. This development will automate the creation of EPICS applications, called IOCs.