Análisis de parámetros de fendas para la estimación de las propiedades mecánicas de vigas de madera de Pinus sylvestris L. Analysis of parameters for assessing drying fissures to estimate their influence on the mechanical properties of Pinus sylvestris L. wooden beams

El principal objetivo de este estudio es evaluar la influencia de las fendas de secado en las propiedades mecánicas de vigas de madera. Para esto, se utilizan 40 vigas de Pino silvestre (Pinus sylvestris L) de 4200 mm de longitud y 150x200 mm de sección que fueron ensayadas según norma EN 408. Las fendas se registran detalladamente atendiendo a su longitud y posición en cada cara de la viga, y midiendo el espesor y la profundidad cada 100mm a lo largo de la viga. Solo el 10% de la muestra es rechazada por las fendas, según los criterios establecidos por la norma española de clasificación visual UNE 56544. Para evaluar la influencia de las fendas en las propiedades mecánicas, se usan tres parámetros globales basados en el área, el volumen o la profundad de la fenda, y dos locales basados en la profundidad máxima y la profundidad en la zona de rotura. Además se determina la densidad de las piezas. Estos parámetros se comparan con las propiedades mecánicas (tensión de rotura, módulo de elasticidad y energía de rotura) y se encuentra escasa relación entre ellos. Las mejores correlaciones se encuentran entre los parámetros relacionados con la profundidad de las fendas, tanto con el módulo de elasticidad como con la tensión de rotura. The aim of this study is the evaluation of the influence of drying fissures on the mechanical properties of timber beams. For that purpose, 40 sawn timber pieces of Scots pine (Pinus sylvestris L.) with 150x200 mm in cross-section and 4200 mm in length have been tested according to EN 408, obtaining MOR and MOE. The fissures were registered in detail measuring their length and position in each face of the beam, and the thickness and depth every 100 mm in length. Only 10 % of the pieces were rejected because fissures, according to UNE 56544 Spanish visual grading standard. To evaluate the influence of fissures in mechanical properties three global parameters: Fissures Area Ratio or ratio between the area occupied by fissures and the total area in the neutral axis plane of the beam; Fissures Volume Ratio or ratio between volume of fissures and the total volume of the beam; Fissures Average Depth and two local parameters were used: Fissures Maximum Depth in the beam, and Fissures Depth in the broken zone of the beam. Also the density of the beams was registered. These parameters were compared with mechanical properties (tensile strength, elasticity modulus, and rupture energy) and the relationship between them had not been founded. The best relationship was founded between the elasticity modulus y the tensile strength with the parameters which included the depth of the fissures.

Correlating a documentary record of historical floods with the dendrochronological dating of a wooden decking in the old mint of Segovia (Spain)

the aim of this study is to apply an integrated methodological approximation where dendrochronology and documentary analysis allow us to reconstruct the historical flood record of the Segovia Mint. Our hypothesis is that differences between the dendrochronological data of the wooden decking pieces can be related to historical floods and, therefore, they could be used as proxy-source data in future palaeoflood research.

In situ surveillance of capacitive pressure transmitter dynamic poles

In this work, a methodology is proposed to find the dynamic poles of a capacitive pressure transmitter in order to enhance and extend the online surveillance of this type of sensor based on the response time measurement by applying noise analysis techniques and the dynamic data system procedure. Several measurements taken from a pressurized water reactor have been analyzed. The methodology proposes an autoregressive fit whose order is determined by the sensor dynamic poles. Nevertheless, the signals that have been analyzed could not be filtered properly in order to remove the plant noise; thus, this was considered as an additional pair of complex conjugate poles. With this methodology we have come up with the numerical value of the sensor second real pole in spite of its low influence on the sensor dynamic response. This opens up a more accurate online sensor surveillance since the previous methods were achieved by considering one real pole only.

Analysis of teaching experience based on teaching by the case method. Application to reinforcing wooden floors

The technique of reinforcement of wooden floors is a matter clearly multidisciplinary. The teaching of the subject using the "traditional" method, explaining the theory first and then proposing and solving problems has not been successful. This paper discusses the results of a teaching experiencie. It has been the teaching of the subject by the case method. The results are clearly superior to those obtained with the traditional methodology.

Prefab wooden house, Pedrezuela

Proyecto wooden house

One or two poles of attraction in the international technological cooperation process?

In recent years, international cooperation processes have become a key mechanism for companies to internationalise their innovative activities, par ticularly in the case of small businesses whose size reduces their possibilities of developing internationalisation strategies autonomously in the same way as larger companies. In Spain, the existence of two parallel programmes with similar structures oriented towards Europe (EUREKA) and Latin America (IBEROEKA) raises the question as to whether the fact that companies participate in only one (unipolar) or both (bipolar) of these programmes is the result of a selection process, which, in turn, results in the existence of different collectives with different efficiency parameters. The aim of this study is to provide a comparative analysis based on the final reports of Spanish companies that have participated in the EUREKA programme. Two groups of companies were compared: one comprising companies that have only had international experience in Europe (EUREKA); and another formed by companies that have also carried out IBEROEKA projects. The conclusions confirm that the behaviour of both groups of companies differs substantially and reveal the importance of geographical perspective in the analysis of international cooperation in technology. This disparate behaviour is a relevant aspect that must be taken into account when designing policies to promote international technological cooperation.

Calibration of calculation models of wooden guardrails with Operational Modal Analysis

This study analyses the differences between two calculation models for guardrails on building sites that use wooden boards and tubular steel posts. Wood was considered an isotropic material in one model and an orthotropic material in a second model. The elastic constants of the wood were obtained with ultrasound. Frequencies and vibration modes were obtained for both models through linear analysis using the finite element method. The two models were experimentally calibrated through operational modal analysis. The results obtained show that for the three types of wood under analysis, the model which considered them as an orthotropic material fitted the experimental results better than the model which considered them as an isotropic material.

Bovedas Encamonadas: Origen, Evolucion, Geometria y Construccion entre los Siglos XVII y XVIII en el Virreinato de Perú

Desde la creación del Virreinato del Perú, en el siglo XVI, los arcos, bóvedas y cúpulas se acostumbraban a levantar con piedra y fábrica. Sin embargo estas tierras eran sacudidas periodicamente por terremotos, produciendo el colapso de la mayoría de estas edificaciones. Para el siglo XVII los alarifes ya habían experimentado diversas maneras de levantar bóvedas, sin haberse encontrado una respuesta razonable en términos de tiempo, economía y estabilidad frente a los sismos. En medio de este panorama se produjo la introducción de las bóvedas encamonadas a mediados del siglo XVII, consolidandose en el resto de la centuria hasta el punto de terminar convirtiéndose en un recurso tradicional y de estimada elaboración dentro de la arquitectura virreinal peruana. Las bóvedas encamonadas se realizaban con tablas de madera (camones) que se solapaban entre sí para formar arcos (cerchas), los cuales definían la forma que tendrían las bóvedas, y eran estabilizados lateralmente mediante correas. Sobre los arcos y correas se colocaba un cerramiento que podía ser un entablado, unos listones de madera o simplemente un tendido a base de cañas. En la mayoría de casos se finalizaba con un recubrimiento aislante de barro por el extradós y otro decorativo de yeso por el intradós. Precisamente estas bóvedas constituyen el objeto de la presente tesis, específicamente en su devenir histórico entre los siglos XVII y XVIII en el ámbito territorial del Virreinato del Perú, partiendo del examen de los tratados de arquitectura coetáneos y del estudio de las bóvedas de madera en España, para finalizar con el análisis de las características geométricas y constructivas que lograron definir en ellas los alarifes peruanos. Since the creation of the Viceroyalty of Peru, in the sixteenth century, arches, vaults and domes were accustomed to build with stone and masonry. However, these lands were periodically shaken by earthquakes, causing the collapse of most of these buildings. For the seventeenth century the master masons had already experienced several ways to build vaults, without having found a reasonable response in terms of time, economy and stability against earthquakes. Into this context the master carpenters introduced the wooden vaults since seventeenth century, and this constructive system was consolidated around the rest of the century to the end point of becoming a traditional and estimated resource of the Peruvian colonial architecture. The wooden vaults were made with timber planks (camones) that overlapped each other to form arches (cerchas), which defined the shape of the vaults, and were stabilized laterally by purlins. Above the arches and purlins placed planks, wooden strips or just cane. In most cases ended with a mud plaster insulating the extrados and a decorative gypsum plaster on the intrados. Precisely these vaults are the subject of this thesis, specifically in its historical way between the seventeenth and eighteenth centuries in the territory of the Viceroyalty of Peru. Since an examination of the architectural treatises and the Spanish wooden vaults, and concluding with the analysis of the geometric and constructive system that Peruvian builders were able to define on them.

Pasarela peatonal sobre el río Ulla, provincia de Lugo (Galicia)

Se trata de un proyecto de pasarela peatonal colgante sobre el río Ulla, de aproximadamente 36 metros de luz. La especial belleza del área natural en que se situará llevó a la opción de un diseño claro y sencillo para lograr su integración en el lugar. Se busca que la pasarela pase lo más desapercibida posible y deje el protagonismo para el entorno, el río y la naturaleza misma. La difícil accesibilidad de la zona condicionó el diseño y los procedimientos constructivos a adoptar. Se optó por una tipología de pasarela colgante de cables de acero, tablero de madera de castaño y soportes de madera laminada cilíndrica, sobre unos estribos de hormigón armado parcialmente ocultos gracias a su integración en la topografía del lugar. El diseño modular del tablero, construido a base de piezas prefabricadas de madera de castaño que se ensamblan entre sí, permite el montaje en seco mediante avance del tablero sin necesidad de cimbra. Su diseño con dos capas cruzadas de entablado solidarizadas proporciona al conjunto un comportamiento estructural similar al de una placa maciza de madera. This is the project of a suspension footbridge over the Ulla River. It has a span of about 36 meters. The beauty of the natural surroundings where it is located guided the design to the option of a clear and simple proposal with the aim of achieving an integrated project for the area. The footbridge tries to be as invisible as possible with the purpose of maintaining the natural quality of the river and its surroundings. The difficult access to the area conditioned the design and the construction procedures chosen. A suspension footbridge with stainless steel cables, chestnut timber deck and cylindrical glulam piles was designed in the end. The reinforced concrete abutments are partially concealed thanks to their integration in the topography of the area. The deck is built of prefabricated chestnut timber modules that can be joined together at the construction site and can be assembled without the necessity of scaffolding over the river. The design of the deck, with two crossed layers of chestnut boards screwed down together, permits a structural behaviour similar to a solid wooden slab.

Modelización por métodos numéricos de la degradación térmica de un elemento estructural de madera en situación de incendio

La cuantificación de la reducción de las propiedades resistentes y de la sección de un elemento estructural en situación de incendio es fundamental de cara a garantizar la estabilidad estructural en situación de incendio. Existen investigaciones que tratan de determinar la variación de las propiedades térmicas y mecánicas de la madera sometida a cargas térmicas, y la reducción de sección transversal de un elemento estructural de madera. La normativa europea en materia de construcción con madera, el Eurocódigo 5, propone unas simplificaciones para determinar la sección residual de un elemento estructural de madera en situación de incendio. Los objetivos de este trabajo comprenden una revisión de algunos trabajos realizados en el campo de la variación en función de la temperatura de las propiedades térmicas de la madera (calor específico, densidad y conductividad térmica), y la construcción con los distintos valores propuestos de varios modelos de elementos finitos que se someterán a cargas térmicas definidas por la curva ISO 834-1. Los resultados se compararán con un modelo construido con los valores que el Eurocódigo propone y con un ensayo experimental. Como resultado final, se propone finalmente un modelo de elementos finitos que emule el comportamiento del ensayo experimental. The quantification of the decrease of strength properties and section of a structural element in a fire situation is critical in order to guarantee the structural stability in such a fire event. There are some researches in literature trying to find the variation of thermal and mechanical properties of wood subjected to thermal loads, and the decrease of cross section of a wooden structural element. The European legislation on timber construction, Eurocode 5, proposes a simplification to determine the residual section of a wooden structural element in a fire situation. This paper objectives consist in a review of some researches in the field of variations, depending on the temperature, of the thermal properties of wood (specific heat, density and thermal conductivity); and in the construction of a few finite element models of timber structural elements affected by thermal loads according to ISO 834-1. The results were compared with a model based in Eurocode 5 and with an experimental test. As final result, at last, we propose a finite element model that simulates the behavior of the experimental tested element.

Una casa para Einstein: Konrad Wachsmann y la evolucion de un modelo prefabricado desde las casas "Christoph & Unmack A.G." al "General Panel System"

Este artículo estudia la evolución de un modelo de vivienda prefabricada en madera, ejemplificada en la casita de verano que construye Konrad Wachsmann para Albert Einstein en 1929 en Caputh, cerca de Potsdam. El físico deseaba construirse un "lugar de descanso", eligiendo la construcción en madera por su facilidad y rapidez de montaje, adaptabilidad, calidez y para que armonizara mejor con el medio ambiente en el paraje donde se insertaba. Konrad Wachsmann, que trabajaba para la firma de viviendas prefabricadas en madera "Christoph&Unmack A.G." le presentará un modelo prefabricado moderno. Esta tipología, que había evolucionado desde los diseños iniciales "nórdico escandinavos", pasando por el "jugendstil", hasta introducir un nuevo lenguaje de líneas puras, cubierta plana, y grandes ventanales iniciado por Poelzig, será ligeramente modificada por Einstein, que finalmente adjudica el encargo. Ayudado por Einstein a trasladarse a EEUU, Konrad Wachsmann continuará allí la labor de investigación sobre vivienda prefabricada junto con Walter Gropius, que dará como resultado el "General Panel System" y sus conocidas "Packaged Houses". A HOUSE FOR EINSTEIN: KONRAD WACHSMANN AND THE EVOLUTION OF A PREFABRICATED WOODEN HOUSING MODEL FROM " CHRISTOPH & UNMACK A.G." TO "GENERAL PANEL SYSTEM". This article studies the evolution of a prefabricated wooden housing model, exemplified in the summer house built by Konrad Wachsmann for Albert Einstein in 1929, in Caputh, near Potsdam. The Physician wanted to build a "resting house", choosing a wood construction because of its easy and fast assembly, adaptability, warmth and harmony with the environment where it would be inserted. Konrad Wachsmann, who worked for the wooden prefabricated houses firm "Christoph & Unmack AG", proposed Einstein a modern prefabricated wood model. This typology, which had evolved from the initial "Nordic Scandinavian" and "Jugendstil" designs to a new modern language initiated by Poelzig (with clean lines, flat roof, and large windows) will be slightly modified by Einstein, that finally hired the construction of the house. Aided by Einstein to move to USA, Konrad Wachsmann continued there his research work about prefabricated houses with Walter Gropius, giving as a results the "General Panel System" and the popular "Packaged Houses".

Análisis de elementos de madera reforzados con materiales compuestos

Gran parte del patrimonio construido cuenta con edificios cuya estructura está compuesta por elementos de madera. El volumen económico que supone el mantenimiento y renovación de dicho patrimonio es considerable, por ello, es de especial interés el estudio de las diferentes técnicas de refuerzo aplicables a este tipo de estructuras. Las estructuras de madera han sido tradicionalmente reforzadas con piezas del mismo material, aumentando la sección de los elementos dañados, o con acero. La aparición de los materiales compuestos de polímeros reforzados con fibras, y su progresiva aplicación en obras de construcción, hizo que a principios de la década de los noventa se comenzara a aplicar este material en refuerzos de estructuras de madera (Puente de Sins, 1992). La madera es un material natural con una excelente relación entre sus características mecánicas y su peso. Con el uso de materiales compuestos como refuerzo ésta característica se mantiene. En cuanto a su modelo constitutivo, se admite un comportamiento elástico lineal a tracción paralela a la fibra hasta la rotura, mientras que a compresión, se considera un comportamiento lineal elástico inicial, seguido de un tramo plástico. En vigas de madera aserrada sometidas a flexión predomina el modo de fallo por tracción localizándose la fractura frecuentemente en el canto inferior. Los FRP tienen un comportamiento elástico lineal a tracción hasta la rotura y cuentan con excelentes propiedades mecánicas en relación a su peso y volumen. Si se refuerza la viga por el canto inferior se aumentará su capacidad de absorber tracciones y por tanto, es previsible que se produzca un incremento en la capacidad de carga, así como un aumento de ductilidad. En este trabajo se analizan los beneficios que aportan distintos sistemas de refuerzos de materiales compuestos. El objetivo es contribuir al conocimiento de esta técnica para la recuperación o aumento de las propiedades resistentes de elementos de madera sometidos a flexión. Se ha llevado a cabo un estudio basado en datos obtenidos experimentalmente mediante el ensayo a flexión de vigas de madera de pino silvestre reforzadas con materiales compuestos. Las fibras que componen los tejidos utilizados para la ejecución de los refuerzos son de basalto y de carbono. En el caso de los compuestos de fibra de basalto se aplican en distintos gramajes, y los de carbono en tejido unidireccional y bidireccional. Se analiza el comportamiento de las vigas según las variables de refuerzo aplicadas y se comparan con los resultados de vigas ensayadas sin reforzar. Además se comprueba el ajuste del modelo de cálculo no lineal aplicado para predecir la carga de rotura de cada viga reforzada. Con este trabajo queda demostrado el buen funcionamiento del FRP de fibra de basalto aplicado en el refuerzo de vigas de madera y de los tejidos de carbono bidireccionales con respecto a los unidireccionales. ABSTRACT Many of the buildings of the built heritage include a structure composed by timber elements. The economic volume involved in the maintenance and renewal of this built heritage is considerable, therefore, the study of the different reinforcement techniques applicable to this type of structure is of special interest. The wooden structures have traditionally been reinforced either with steel or with pieces of the same material, increasing the section of the damaged parts. The emergence of polymer composites reinforced with fibers, and their progressive use in construction, started to be applied as reinforcement in timber structures at the beginning of the nineties decade in the 20th century (Sins Bridge, 1992). Wood is a natural material with an excellent ratio between its mechanic characteristics and its weight. This feature is maintained with the use of composites as reinforcement. In terms of its constitutive model, linear elastic behavior parallel to the fiber up to fracture is admitted when subjected to tensile stress, while under compression, an initial linear elastic behavior, followed by a section plasticizing, is considered. In sawn timber beams subjected to bending, the predominant failure is mainly due to tensile stress; and frequently the fracture is located at the beam lower face. The FRP have a linear elastic behavior until fracture occurs, and have excellent mechanical properties in relation to their weight and volume. If the beam is reinforced by its lower face, its capacity to absorb tensile stresses will increase, and therefore, an increase in its carrying capacity is likely to be produced, as well as an increase in ductility. This work analyzes the benefits different reinforcement systems of composite materials provide, with the aim of contributing to the knowledge of this technique for recovering or increasing the strength properties of timber elements subjected to bending loads. It is a study based on data obtained experimentally using bending tests of pine timber beams reinforced with composite materials. Fibers used for the execution of the reinforcement are basalt and carbon. Basalt fiber composites are applied in different grammages, whereas with carbon composites, unidirectional and bidirectional fabrics are used. The behavior of the beams was analyzed regarding the reinforcement variables applied, and the results are compared with those of the tested beams without reinforcement. Furthermore it has been proved adjunting the nonlinear calculation model applied to predict the failure load of each reinforced beam. This work proves the good behavior of fiber reinforce plastic (FRP) with basalt fiber when applied to timber beams, and that of bidirectional carbon fabrics as opposed to the unidirectional ones.

AR modelling and DDS for in situ surveillance of capacitive pressure transmitters

In this work, a methodology is proposed to find the dynamics poles of a capacitive pressure transmitter in order to enhance and extend the on line surveillance of this type of sensors based on the response time measurement by applying noise analysis techniques and the Dynamic Data System. Several measurements have been analyzed taken from a Pressurized Water Reactor. The methodology proposes an autoregressive fit whose order is determined by the sensor dynamics poles. Nevertheless, the signals that have been analyzed, could not be filtered properly in order to remove the plant noise, thus, this was considered as an additional pair of complex conjugate poles. With this methodology we have come up with the numerical value of the sensor second real pole in spite of its low influence on the sensor dynamic response. This opens up a more accurate on line sensor surveillance since the previous methods were achieved by considering one real pole only.

Direct and Inverse Results on Row Sequences of Hermite-Pad, Approximants

We give necessary and sufficient conditions for the convergence with geometric rate of the common denominators of simultaneous rational interpolants with a bounded number of poles. The conditions are expressed in terms of intrinsic properties of the system of functions used to build the approximants. Exact rates of convergence for these denominators and the simultaneous rational approximants are provided.

Meromorphic continuation of functions and arbitrary distribution of interpolation points

We characterize the region of meromorphic continuation of an analytic function ff in terms of the geometric rate of convergence on a compact set of sequences of multi-point rational interpolants of ff. The rational approximants have a bounded number of poles and the distribution of interpolation points is arbitrary.