Repeatability and Two-Dimensionality of Model Scale Sloshing Impacts

Canonical test cases for sloshing wave impact problems are pre-sented and discussed. In these cases the experimental setup has been simpli?ed seeking the highest feasible repeatability; a rectangular tank subjected to harmonic roll motion has been the tested con?guration. Both lateral and roof impacts have been studied, since both cases are relevant in sloshing assessment and show speci?c dynamics. An analysis of the impact pressure of the ?rst four impact events is provided in all cases. It has been found that not in all cases a Gaussian ?tting of each individual peak is feasible. The tests have been conducted with both water and oil in order to obtain high and moderate Reynolds number data; the latter may be useful as simpler test cases to assess the capabilities of CFD codes in simulating sloshing impacts. The re-peatability of impact pressure values increases dramatically when using oil. In addition, a study of the two-dimensionality of the problem using a tank con?guration that can be adjusted to 4 di?erent thicknesses has been carried out. Though the kinemat-ics of the free surface does not change signi cantly in some of the cases, the impact pressure values of the ?rst impact events changes substantially from the small to the large aspect ratios thus meaning that attention has to be paid to this issue when reference data is used for validation of 2D and 3D CFD codes.

Competitive exclusion in a two-especies chemotasis model

We consider a mathematical model for the spatio-temporal evolution of two biological species in a competitive situation. Besides diffusing, both species move toward higher concentrations of a chemical substance which is produced by themselves. The resulting system consists of two parabolic equations with Lotka–Volterra-type kinetic terms and chemotactic cross-diffusion, along with an elliptic equation describing the behavior of the chemical. We study the question in how far the phenomenon of competitive exclusion occurs in such a context. We identify parameter regimes for which indeed one of the species dies out asymptotically, whereas the other reaches its carrying capacity in the large time limit.

On a two species chemotaxis model with slow chemical diffucion.

In this paper we consider a system of three parabolic equations modeling the behavior of two biological species moving attracted by a chemical factor. The chemical substance verifies a parabolic equation with slow diffusion. The system contains second order terms in the first two equations modeling the chemotactic effects. We apply an iterative method to obtain the global existence of solutions using that the total mass of the biological species is conserved. The stability of the homogeneous steady states is studied by using an energy method. A final example is presented to illustrate the theoretical results.

Prediction of bendig load capacity of timber beams by finite element method simulation of knots and grain deviation

A finite element model was used to simulate timberbeams with defects and predict their maximum load in bending. Taking into account the elastoplastic constitutive law of timber, the prediction of fracture load gives information about the mechanisms of timber failure, particularly with regard to the influence of knots, and their local graindeviation, on the fracture. A finite element model was constructed using the ANSYS element Plane42 in a plane stress 2D-analysis, which equates thickness to the width of the section to create a mesh which is as uniform as possible. Three sub-models reproduced the bending test according to UNE EN 408: i) timber with holes caused by knots; ii) timber with adherent knots which have structural continuity with the rest of the beam material; iii) timber with knots but with only partial contact between knot and beam which was artificially simulated by means of contact springs between the two materials. The model was validated using ten 45 × 145 × 3000 mm beams of Pinus sylvestris L. which presented knots and graindeviation. The fracture stress data obtained was compared with the results of numerical simulations, resulting in an adjustment error less of than 9.7%

Prediction of near field overpressure from quarry blasting

This paper investigates the propagation of airblast or pressure waves in air produced by bench blasting (i.e. detonation of the explosive in a row of blastholes, breaking the burden of rock towards the free vertical face of the block). Peak overpressure is calculated as a function of blasting parameters (explosive mass per delay and velocity at which the detonation sequence proceeds along the bench) and the polar coordinates of the position of interest (distance to the source and azimuth with respect to the free face). The model has been fitted to empirical data using linear least squares. The data set is composed of 122 airblast records monitored at distances less than 400 m in 41 production blasts carried out in two quarries. The model is statistically significant and has a determination coefficient of 0.87. The formula is validated from 12 airblast measurements gathered in five additional blasts.

Modelos de métrica para sistemas electrónicos de adquisición de datos y de procesamiento para investigación clínica con dispositivos cardiacos implantables

RESUMEN Las enfermedades cardiovasculares constituyen en la actualidad la principal causa de mortalidad en el mundo y se prevé que sigan siéndolo en un futuro, generando además elevados costes para los sistemas de salud. Los dispositivos cardiacos implantables constituyen una de las opciones para el diagnóstico y el tratamiento de las alteraciones del ritmo cardiaco. La investigación clínica con estos dispositivos alcanza gran relevancia para combatir estas enfermedades que tanto afectan a nuestra sociedad. Tanto la industria farmacéutica y de tecnología médica, como los propios investigadores, cada día se ven involucrados en un mayor número de proyectos de investigación clínica. No sólo el incremento en su volumen, sino el aumento de la complejidad, están generando mayores gastos en las actividades asociadas a la investigación médica. Esto está conduciendo a las compañías del sector sanitario a estudiar nuevas soluciones que les permitan reducir los costes de los estudios clínicos. Las Tecnologías de la Información y las Comunicaciones han facilitado la investigación clínica, especialmente en la última década. Los sistemas y aplicaciones electrónicos han proporcionado nuevas posibilidades en la adquisición, procesamiento y análisis de los datos. Por otro lado, la tecnología web propició la aparición de los primeros sistemas electrónicos de adquisición de datos, que han ido evolucionando a lo largo de los últimos años. Sin embargo, la mejora y perfeccionamiento de estos sistemas sigue siendo crucial para el progreso de la investigación clínica. En otro orden de cosas, la forma tradicional de realizar los estudios clínicos con dispositivos cardiacos implantables precisaba mejorar el tratamiento de los datos almacenados por estos dispositivos, así como para su fusión con los datos clínicos recopilados por investigadores y pacientes. La justificación de este trabajo de investigación se basa en la necesidad de mejorar la eficiencia en la investigación clínica con dispositivos cardiacos implantables, mediante la reducción de costes y tiempos de desarrollo de los proyectos, y el incremento de la calidad de los datos recopilados y el diseño de soluciones que permitan obtener un mayor rendimiento de los datos mediante la fusión de datos de distintas fuentes o estudios. Con este fin se proponen como objetivos específicos de este proyecto de investigación dos nuevos modelos: - Un modelo de recuperación y procesamiento de datos para los estudios clínicos con dispositivos cardiacos implantables, que permita estructurar y estandarizar estos procedimientos, con el fin de reducir tiempos de desarrollo Modelos de Métrica para Sistemas Electrónicos de Adquisición de Datos y de Procesamiento para Investigación Clínica con Dispositivos Cardiacos Implantables de estas tareas, mejorar la calidad del resultado obtenido, disminuyendo en consecuencia los costes. - Un modelo de métrica integrado en un Sistema Electrónico de Adquisición de Datos (EDC) que permita analizar los resultados del proyecto de investigación y, particularmente del rendimiento obtenido del EDC, con el fin de perfeccionar estos sistemas y reducir tiempos y costes de desarrollo del proyecto y mejorar la calidad de los datos clínicos recopilados. Como resultado de esta investigación, el modelo de procesamiento propuesto ha permitido reducir el tiempo medio de procesamiento de los datos en más de un 90%, los costes derivados del mismo en más de un 85% y todo ello, gracias a la automatización de la extracción y almacenamiento de los datos, consiguiendo una mejora de la calidad de los mismos. Por otro lado, el modelo de métrica posibilita el análisis descriptivo detallado de distintos indicadores que caracterizan el rendimiento del proyecto de investigación clínica, haciendo factible además la comparación entre distintos estudios. La conclusión de esta tesis doctoral es que los resultados obtenidos han demostrado que la utilización en estudios clínicos reales de los dos modelos desarrollados ha conducido a una mejora en la eficiencia de los proyectos, reduciendo los costes globales de los mismos, disminuyendo los tiempos de ejecución, e incrementando la calidad de los datos recopilados. Las principales aportaciones de este trabajo de investigación al conocimiento científico son la implementación de un sistema de procesamiento inteligente de los datos almacenados por los dispositivos cardiacos implantables, la integración en el mismo de una base de datos global y optimizada para todos los modelos de dispositivos, la generación automatizada de un repositorio unificado de datos clínicos y datos de dispositivos cardiacos implantables, y el diseño de una métrica aplicada e integrable en los sistemas electrónicos de adquisición de datos para el análisis de resultados de rendimiento de los proyectos de investigación clínica. ABSTRACT Cardiovascular diseases are the main cause of death worldwide and it is expected to continue in the future, generating high costs for health care systems. Implantable cardiac devices have become one of the options for diagnosis and treatment of cardiac rhythm disorders. Clinical research with these devices has acquired great importance to fight against these diseases that affect so many people in our society. Both pharmaceutical and medical technology companies, and also investigators, are involved in an increasingly number of clinical research projects. The growth in volume and the increase in medical research complexity are contributing to raise the expenditure level associated with clinical investigation. This situation is driving health care sector companies to explore new solutions to reduce clinical trial costs. Information and Communication Technologies have facilitated clinical research, mainly in the last decade. Electronic systems and software applications have provided new possibilities in the acquisition, processing and analysis of clinical studies data. On the other hand, web technology contributed to the appearance of the first electronic data capture systems that have evolved during the last years. Nevertheless, improvement of these systems is still a key aspect for the progress of clinical research. On a different matter, the traditional way to develop clinical studies with implantable cardiac devices needed an improvement in the processing of the data stored by these devices, and also in the merging of these data with the data collected by investigators and patients. The rationale of this research is based on the need to improve the efficiency in clinical investigation with implantable cardiac devices, by means of reduction in costs and time of projects development, as well as improvement in the quality of information obtained from the studies and to obtain better performance of data through the merging of data from different sources or trials. The objective of this research project is to develop the next two models: • A model for the retrieval and processing of data for clinical studies with implantable cardiac devices, enabling structure and standardization of these procedures, in order to reduce the time of development of these tasks, to improve the quality of the results, diminish therefore costs. • A model of metric integrated in an Electronic Data Capture system (EDC) that allow to analyze the results of the research project, and particularly the EDC performance, in order to improve those systems and to reduce time and costs of the project, and to get a better quality of the collected clinical data. As a result of this work, the proposed processing model has led to a reduction of the average time for data processing by more than 90 per cent, of related costs by more than 85 per cent, and all of this, through automatic data retrieval and storage, achieving an improvement of quality of data. On the other hand, the model of metrics makes possible a detailed descriptive analysis of a set of indicators that characterize the performance of each research project, allowing inter‐studies comparison. This doctoral thesis results have demonstrated that the application of the two developed models in real clinical trials has led to an improvement in projects efficiency, reducing global costs, diminishing time in execution, and increasing quality of data collected. The main contributions to scientific knowledge of this research work are the implementation of an intelligent processing system for data stored by implantable cardiac devices, the integration in this system of a global and optimized database for all models of devices, the automatic creation of an unified repository of clinical data and data stored by medical devices, and the design of a metric to be applied and integrated in electronic data capture systems to analyze the performance results of clinical research projects.

Influencia del viento transversal en sistemas ferroviarios = Cross-wind effects on railway infrastructure

El viento, como factor medio-ambiental, ha sido objeto de numerosos estudios por los efectos que induce tanto en vehículos como en estructuras. Dentro del ámbito ferroviario, las cargas aerodinámicas debidas a la acción del viento transversal pueden poner en compromiso la seguridad de los vehículos en circulación, pudiendo llegar a ocasionar el vuelco del mismo. Incluso el sistema de cables encargado de realizar el suministro eléctrico necesario para la tracción del tren, conocido como catenaria, es sensible a la acción del viento. De hecho, al igual que ocurre en ciertas estructuras de cables, la interacción entre las fuerzas aerodinámicas no estacionarias y la catenaria puede ocasionar la aparición de oscilaciones de gran amplitud debido al fenómeno de galope. Una forma sencilla de reducir los efectos no deseados de la acción del viento, es la instalación de barreras cortavientos aguas arriba de la zona que se desea proteger. La instalación de estos dispositivos, reduce la velocidad en la estela generada, pero también modifica las propiedades del flujo dentro de la misma. Esta alteración de las condiciones del flujo puede contribuir a la aparición del fenómeno de galope en estructuras caracterizadas por su gran flexibilidad, como la catenaria ferroviaria. Estos dos efectos contrapuestos hacen evidente la importancia de mantener cierta visión global del efecto introducido por la instalación de barreras cortavientos en la plataforma ferroviaria. A lo largo de este documento, se evalúa desde un enfoque multidisciplinar el efecto inducido por las barreras cortavientos en varios subsistemas ferroviarios. Por un lado se analizan las mejoras en la estabilidad lateral del vehículo mediante una serie de ensayos en túnel de viento. La medición de la distribución de presiones en la superficie de un modelo bidimensional de vehículo ferroviario proporciona una buena estimación del nivel de protección que se consigue en función de la altura de una barrera cortavientos. Por otra parte, se analiza la influencia del mismo juego de barreras cortavientos en las características del flujo situado sobre la plataforma ferroviaria, mediante la utilización de anemometría de hilo caliente (HWA) y velocimetría de imágenes de párticulas (PIV). En particular se centra la atención en las características en la posición correspondiente a los hilos conductores de la catenaria. En la última parte del documento, se realiza un análisis simplificado de la aparición oscilaciones en la catenaria, por el efecto de la inestabilidad de galope. La información obtenida sobre las características del flujo se combinan con las propiedades aerodinámicas del hilo de contacto, obtenidas en mediante una serie de ensayos en túnel de viento. De esta manera se realiza una evaluación del riesgo a la aparición de este tipo de inestabilidad aeroeslástica aplicada a una catenaria ferroviaria situada sobre un viaducto tipo. ABSTRACT Wind as an environmental factor may induce undesirable effects on vehicles and structures. The analysis of those effects has caught the attention of several researchers. Concerning the railway system, cross-wind induces aerodynamic loads on rolling stock that may increase the overturning risk of the vehicle, threatening its safe operation. Even the cable system responsible to provide the electric current required for the train traction, known as the railway overhead or catenary, is sensitive to the wind action. In fact, the interaction between the unsteady aerodynamic forces and the railway overhead may trigger the development of undamped oscillations due to galloping phenomena. The inclusion of windbreaks upstream the area that needs wind protection is a simple mean to palliate the undesirable effects caused by the wind action. Although the presence of this wind protection devices reduces the wind speed downstream, they also modify the flow properties inside their wake. This modification on the flow characteristics may ease the apparition of the galloping phenomena on flexible structures, such as the railway overhead. This two opposite effects require to maintain a global perspective on the analysis of the influence of the windbreak presence. In the present document, a multidisciplinary analysis on the effect induced by windbreaks on several railways subsystems is conducted. On the one hand, a set of wind tunnel tests is conducted to assess the improvement on the rolling stock lateral stability. The qualitative estimation of the shelter effect, as function of the windbreak height, is established through the pressure distribution measured on the surface of a two-dimensional train model. On the other hand, the flow properties above the railway platform are assessed using the same set of windbreaks. Two experimental techniques are used to measure the flow properties, hot-wire anemometry (HWA) and particle image velocimetry (PIV). In particular, the attention is focused on the flow characteristics on the contact wire location. A simplified analysis on the catenary oscillations due to galloping phenomena is conducted in the last part of the document. Both, the flow characterization performed via PIV and the aerodynamic properties of the contact wire cross-section are combined. In this manner, the risk of the aeroelastic instabilities on a railway overhead placed on a railway bridge is assessed through a practical application.

Análisis del efecto laminador del cauce utilizando modelos fluviales bidimensionales

El método de Muskingum-Cunge, con más de 45 años de historia, sigue siendo uno de los más empleados a la hora de calcular el tránsito en un cauce. Una vez calibrado, permite realizar cálculos precisos, siendo asimismo mucho más rápido que los métodos que consideran las ecuaciones completas. Por esta razón, en el presente trabajo de investigación se llevó a cabo un análisis de su precisión, comparándolo con los resultados de un modelo hidráulico bidimensional. En paralelo se llevó a cabo un análisis de sus limitaciones y se ensayó una metodología práctica de aplicación. Con esta motivación se llevaron a cabo más de 200 simulaciones de tránsito en cauces prismáticos y naturales. Los cálculos se realizaron empleando el programa HEC-HMS con el método de Muskingum-Cunge de sección de 8 puntos, así como con la herramienta de cálculo hidráulico bidimensional InfoWorks ICM. Se eligieron HEC-HMS por su gran difusión e InfoWorks ICM por su rapidez de cálculo, pues emplea la tecnología CUDA (Arquitectura Unificada de Dispositivos de Cálculo). Inicialmente se validó el modelo hidráulico bidimensional contrastándolo con la formulación unidimensional en régimen uniforme y variado, así como con fórmulas analíticas de régimen variable, consiguiéndose resultados muy satisfactorios. También se llevó a cabo un análisis de la sensibilidad al mallado del modelo bidimensional aplicado a tránsitos, obteniéndose unos ábacos con tamaños recomendados de los elementos 2D que cuantifican el error cometido. Con la técnica del análisis dimensional se revisó una correlación de los resultados obtenidos entre ambos métodos, ponderando su precisión y definiendo intervalos de validez para la mejor utilización del método de Muskingum-Cunge. Simultáneamente se desarrolló una metodología que permite obtener la sección característica media de 8 puntos para el cálculo de un tránsito, basándose en una serie de simulaciones bidimensionales simplificadas. De este modo se pretende facilitar el uso y la correcta definición de los modelos hidrológicos. The Muskingum-Cunge methodology, which has been used for more 45 than years, is still one of the main procedures to calculate stream routing. Once calibrated, it gives precise results, and it is also much faster than other methods that consider the full hydraulic equations. Therefore, in the present investigation an analysis of its accuracy was carried out by comparing it with the results of a two-dimensional hydraulic model. At the same time, reasonable ranges of applicability as well as an iterative method for its adequate use were defined. With this motivation more than 200 simulations of stream routing were conducted in both synthetic and natural waterways. Calculations were performed with the aid of HEC-HMS choosing the Muskingum-Cunge 8 point cross-section method and in InfoWorks ICM, a two-dimensional hydraulic calculation software. HEC-HMS was chosen because its extensive use and InfoWorks ICM for its calculation speed as it takes advantage of the CUDA technology (Compute Unified Device Architecture). Initially, the two-dimensional hydraulic engine was compared to one-dimensional formulation in both uniform and varied flow. Then it was contrasted to variable flow analytical formulae, achieving most satisfactory results. A sensitivity size analysis of the two-dimensional rooting model mesh was also conduced, obtaining charts with suggested 2D element sizes to narrow the committed error. With the technique of dimensional analysis a correlation of results between the two methods was reviewed, assessing their accuracy and defining valid intervals for improved use of the Muskingum-Cunge method. Simultaneously, a methodology to draw a representative 8 point cross-section was developed, based on a sequence of simplified two-dimensional simulations. This procedure is intended to provide a simplified approach and accurate definition of hydrological models.

Spawning and habitat management in salmonid populations at the southern edge of their natural ranges = Reproducción y gestión del hábitat en poblaciones de salmónidos en el extremo meridional de sus distribuciones naturales

Las poblaciones de salmónidos en la Península Ibérica (trucha común, Salmo trutta; y salmón atlántico, Salmo salar) se encuentran cerca del límite meridional de sus distribuciones naturales, y por tanto tienen una gran importancia para la conservación de estas especies. En la presente Tesis se han investigado algunos aspectos de la reproducción y de la gestión del hábitat, con el objeto de mejorar el conocimiento acerca de estas poblaciones meridionales de salmónidos. Se ha estudiado la reproducción de la trucha común en el río Castril (Andalucía, sur de España), donde se ha observado que la freza ocurre desde diciembre hasta abril con el máximo de actividad en febrero. Este hecho representa uno de los periodos reproductivos más tardíos y con mayor duración de toda la distribución natural de la especie. Además, actualmente se sabe que el resto de poblaciones andaluzas tienen periodos de reproducción similares (retrasados y extendidos). Análisis en la escala de la distribución natural de la trucha común, han mostrado que la latitud explica parcialmente tanto la fecha media de reproducción (R2 = 62.8%) como la duración del periodo de freza (R2 = 24.4%) mediante relaciones negativas: a menor latitud, la freza ocurre más tarde y durante más tiempo. Es verosímil que un periodo de freza largo suponga una ventaja para la supervivencia de las poblaciones de trucha en hábitats impredecibles, y por tanto se ha propuesto la siguiente hipótesis, que deberá ser comprobada en el futuro: la duración de la freza es mayor en hábitats impredecibles que en aquellos más predecibles. La elevada tasa de solapamiento de frezaderos observada en el río Castril no se explica únicamente por una excesiva densidad de reproductores. Las hembras de trucha eligieron lugares específicos para construir sus frezaderos en vez de dispersarse aleatoriamente dentro del hábitat adecuado para la freza que tenían disponible. Estas observaciones sugieren que las hembras tienen algún tipo de preferencia por solapar sus frezaderos. Además, en ríos calizos como el Castril, las gravas pueden ser muy cohesivas y difíciles de excavar, por lo que el solapamiento de frezaderos puede suponer una ventaja para la hembra, porque la excavación en sustratos que han sido previamente removidos por frezas anteriores requerirá menos gasto de energía que en sustratos con gravas cohesivas que no han sido alteradas. Por tanto, se ha propuesto la siguiente hipótesis, que deberá ser comprobada en el futuro: las hembras tienen una mayor preferencia por solapar sus frezaderos en ríos con sustratos cohesivos que en ríos con sustratos de gravas sueltas. En el marco de la gestión del hábitat, se han empleado dos enfoques diferentes para la evaluación del hábitat físico, con el objeto de cuantificar los cambios potenciales en la disponibilidad de hábitat, antes de la implementación real de determinadas medidas sobre el hábitat. En primer lugar, se ha evaluado el hábitat físico del salmón atlántico en el río Pas (Cantabria, norte de España), en la escala del microhábitat, empleando la metodología IFIM junto con un modelo hidráulico bidimensional (River2D). Se han simulado una serie de acciones de mejora del hábitat y se han cuantificado los cambios en el hábitat bajo estas acciones. Los resultados mostraron un aumento muy pequeño en la disponibilidad de hábitat, por lo que no sería efectivo implementar estas acciones en este tramo fluvial. En segundo lugar, se ha evaluado el hábitat físico de la trucha común en el río Tajuña (Guadalajara, centro de España), en la escala del mesohábitat, empleando la metodología MesoHABSIM. Actualmente, el río Tajuña está alterado por los usos agrícolas de sus riberas, y por tanto se ha diseñado una restauración para mitigar estos impactos y para llevar al río a un estado más natural. Se ha cuantificado la disponibilidad de hábitat tras la restauración planteada, y los resultados han permitido identificar los tramos en los que la restauración resultaría más eficaz. ABSTRACT Salmonid populations in the Iberian Peninsula (brown trout, Salmo trutta; and Atlantic salmon, Salmo salar) are close to the southern limit of their natural ranges, and therefore they are of great importance for the conservation of the species. In the present dissertation, some aspects of spawning and habitat management have been investigated, in order to improve the knowledge on these southern salmonid populations. Brown trout spawning have been studied in the river Castril (Andalusia, southern Spain), and it has been observed that spawning occurs from December until April with the maximum activity in February. This finding represents one of the most belated and protracted spawning periods within the natural range of the species. Furthermore, it is now known that the rest of Andalusian populations show similar (belated and extended) spawning periods. Broad-scale analyses throughout the brown trout natural range showed that latitude partly explained both spawning mean time (R2 = 62.8%) and spawning duration (R2 = 24.4%) by negative relationships: the lower the latitude, the later the spawning time and the longer the spawning period. It is plausible that a long spawning period would be an advantage for survival of trout populations in unpredictable habitats, and thus the following hypothesis has been proposed, which is yet to be tested: spawning duration is longer in unpredictable than in predictable habitats. High rate of redd superimposition observed in the river Castril was not only caused by high density of spawners. Trout females chose specific sites for redd construction instead of randomly dispersing over the suitable spawning habitat. These observations suggest that female spawners have some kind of preference for superimposing redds. Moreover, in limestone streams such as Castril, unused gravels can be very cohesive and hard to dig, and thus redd superimposition may be an advantage for female, because digging may require less energy expenditure in already used redd sites than in cohesive and embedded unused sites. Hence, the following hypothesis has been proposed, which is yet to be tested: females have a higher preference for superimposing redds in streambeds with cohesive and embedded substrates than in rivers with loose gravels. Within the topic of habitat management, two different approaches have been used for physical habitat assessment, in order to quantify the potential change in habitat availability, prior to the actual implementation of proposed habitat measures. Firstly, physical habitat for Atlantic salmon in the river Pas (Cantabria, northern Spain) has been assessed at the microhabitat scale, using the IFIM approach along with a two dimensional hydraulic model (River2D). Proposed habitat enhancement actions have been simulated and potential habitat change has been quantified. Results showed a very small increasing in habitat availability and therefore it is not worth to implement these measures in this stream reach. Secondly, physical habitat for brown trout in the river Tajuña (Guadalajara, central Spain) has been assessed at the mesohabitat scale, using the MesoHABSIM approach. The river Tajuña is currently impacted by surrounding agricultural uses, and thus restoration was designed to mitigate these impacts and to drive the river to a more natural state. Habitat availability after the planned restoration has been quantified, and the results have permitted to identify in which sites the restoration will be more effective.

Analytical study of the thermal behaviour and stability of a small satellite

In this work the thermal analysis of a small satellite orbiting around the Earth has been approached by direct integration of the heat balance equations of a two-node reduced model, obtaining a linearized second order ODE problem, similar in form to the classical case of the forced vibration of a damped system. As the thermal loads (solar radiation, albedo, etc.) are harmonic, the problem is solved by means of Fourier analysis methods. Research on that field can be directly applied to the analysis of thermal problems and the results obtained are satisfactory. Working on the frequency domain streamlines the analysis, simplifies the study and facilitates the experimental testing. The transfer functions are obtained for the two-node case but the study can be extended to an n-node model.

Energy/power consumption model for an embedded processor board

This dissertation, whose research has been conducted at the Group of Electronic and Microelectronic Design (GDEM) within the framework of the project Power Consumption Control in Multimedia Terminals (PCCMUTE), focuses on the development of an energy estimation model for the battery-powered embedded processor board. The main objectives and contributions of the work are summarized as follows: A model is proposed to obtain the accurate energy estimation results based on the linear correlation between the performance monitoring counters (PMCs) and energy consumption. the uniqueness of the appropriate PMCs for each different system, the modeling methodology is improved to obtain stable accuracies with slight variations among multiple scenarios and to be repeatable in other systems. It includes two steps: the former, the PMC-filter, to identify the most proper set among the available PMCs of a system and the latter, the k-fold cross validation method, to avoid the bias during the model training stage. The methodology is implemented on a commercial embedded board running the 2.6.34 Linux kernel and the PAPI, a cross-platform interface to configure and access PMCs. The results show that the methodology is able to keep a good stability in different scenarios and provide robust estimation results with the average relative error being less than 5%. Este trabajo fin de máster, cuya investigación se ha desarrollado en el Grupo de Diseño Electrónico y Microelectrónico (GDEM) en el marco del proyecto PccMuTe, se centra en el desarrollo de un modelo de estimación de energía para un sistema empotrado alimentado por batería. Los objetivos principales y las contribuciones de esta tesis se resumen como sigue: Se propone un modelo para obtener estimaciones precisas del consumo de energía de un sistema empotrado. El modelo se basa en la correlación lineal entre los valores de los contadores de prestaciones y el consumo de energía. Considerando la particularidad de los contadores de prestaciones en cada sistema, la metodología de modelado se ha mejorado para obtener precisiones estables, con ligeras variaciones entre escenarios múltiples y para replicar los resultados en diferentes sistemas. La metodología incluye dos etapas: la primera, filtrado-PMC, que consiste en identificar el conjunto más apropiado de contadores de prestaciones de entre los disponibles en un sistema y la segunda, el método de validación cruzada de K iteraciones, cuyo fin es evitar los sesgos durante la fase de entrenamiento. La metodología se implementa en un sistema empotrado que ejecuta el kernel 2.6.34 de Linux y PAPI, un interfaz multiplataforma para configurar y acceder a los contadores. Los resultados muestran que esta metodología consigue una buena estabilidad en diferentes escenarios y proporciona unos resultados robustos de estimación con un error medio relativo inferior al 5%.

A two-dimensional finite element model of front surface current flow in cells under non-uniform, concentrated illumination

A two-dimensional finite element model of current flow in the front surface of a PV cell is presented. In order to validate this model we perform an experimental test. Later, particular attention is paid to the effects of non-uniform illumination in the finger direction which is typical in a linear concentrator system. Fill factor, open circuit voltage and efficiency are shown to decrease with increasing degree of non-uniform illumination. It is shown that these detrimental effects can be mitigated significantly by reoptimization of the number of front surface metallization fingers to suit the degree of non-uniformity. The behavior of current flow in the front surface of a cell operating at open circuit voltage under non-uniform illumination is discussed in detail.

Reduction in Calculated Uncertainty of a Noise Map by Improving the Traffic Model Data Through Two Phases

The influence of applying European default traffic values to the making of a noise map was evaluated in a typical environment like Palma de Mallorca. To assess these default traffic values, a first model has been created and compared with measured noise levels. Subsequently a second traffic model, improving the input data used for the first one, has been created and validated according to the deviations. Different methodologies were also examined for collecting model input data that would be of higher quality, by analysing the improvement generated in the reduction in the uncertainty of the noise map introduced by the road traffic noise emission

Proposal of an Alternative Model for Speed-Flow Relationship in Two-Lane Highways

A research has been carried out in two-lanehighways in the Madrid Region to propose an alternativemodel for the speed-flowrelationship using regular loop data. The model is different in shape and, in some cases, slopes with respect to the contents of Highway Capacity Manual (HCM). A model is proposed for a mountainous area road, something for which the HCM does not provide explicitly a solution. The problem of a mountain road with high flows to access a popular recreational area is discussed, and some solutions are proposed. Up to 7 one-way sections of two-lanehighways have been selected, aiming at covering a significant number of different characteristics, to verify the proposed method the different classes of highways on which the Manual classifies them. In order to enunciate the model and to verify the basic variables of these types of roads a high number of data have been used. The counts were collected in the same way that the Madrid Region Highway Agency performs their counts. A total of 1.471 hours have been collected, in periods of 5 minutes. The models have been verified by means of specific statistical test (R2, T-Student, Durbin-Watson, ANOVA, etc.) and with the diagnostics of the contrast of assumptions (normality, linearity, homoscedasticity and independence). The model proposed for this type of highways with base conditions, can explain the different behaviors as traffic volumes increase, and follows a polynomial multiple regression model of order 3, S shaped. As secondary results of this research, the levels of service and the capacities of this road have been measured with the 2000 HCM methodology, and the results discussed. © 2011 Published by Elsevier Ltd.

A generic persistence model for CLP systems (and two useful implementations)

This paper describes a model of persistence in (C)LP languages and two different and practically very useful ways to implement this model in current systems. The fundamental idea is that persistence is a characteristic of certain dynamic predicates (Le., those which encapsulate state). The main effect of declaring a predicate persistent is that the dynamic changes made to such predicates persist from one execution to the next one. After proposing a syntax for declaring persistent predicates, a simple, file-based implementation of the concept is presented and some examples shown. An additional implementation is presented which stores persistent predicates in an external datábase. The abstraction of the concept of persistence from its implementation allows developing applications which can store their persistent predicates alternatively in files or databases with only a few simple changes to a declaration stating the location and modality used for persistent storage. The paper presents the model, the implementation approach in both the cases of using files and relational databases, a number of optimizations of the process (using information obtained from static global analysis and goal clustering), and performance results from an implementation of these ideas.