Multi-hazard analysis and identification of priority settlements for land management in Haiti

Seismic hazard study in “La Hispaniola” island in connection with the land tenure situation in the region, in order to define priority areas with a high risk, where some land management recommendations are proposed. The seismic hazard assessment has been carried out following the probabilistic method with a seismogenic zonation and including the major faults of the region as independent units. In order to identify the priority areas, it has taken into account, besides the seismic hazard study, the map of changes of static Coulomb failure stress and the landslide hazard map.

GIS for cartographic accuracy analysis of settlements in the province of Madrid (AGE Tomas Lopez 1804).

Purpose: In this paper we study all settlements shown on the map of the Province of Madrid, sheet number 1 of AGE (Atlas Geográfico de España of Tomas Lopez 1804) and their correspondence with the current ones. This map is divided in to zones: Madrid and Almonacid de Zorita. Method: The steps followed in the methodology are as follow: 1. Geo-reference of maps with latitude and longitude framework. Move the historical longitude origin to the origin longitude of modern cartography. 2 Digitize of all population settlements or cities (97 on Madrid and 42 on Almonacid de Zorita), 3 Identify historic settlements or cities corresponding with current ones. 4. If the maps have the same orientation and scale, replace the coordinate transformation of historical settlements with a new one, by a translation in latitude and longitude equal to the calculated mean value of all ancient map points corresponding to the new. 5. Calculation of absolute accuracy of the two maps. 6 draw in the GIS, the settlements accuracy. Result: It was found that all AGE settlements have good correspondence with current, ie only 27 settlements lost in Madrid and 2 in Almonacid. The average accuracy is 2.3 and 5.7 km to Madrid and Almonacid de Zorita respectively. Discussion & Conclusion: The final accuracy map obtained shows that there is less error in the middle of the map. This study highlights the great work done by Tomas Lopez in performing this mapping without fieldwork. This demonstrates the great value that has been the work of Tomas Lopez in the history of cartography.

Impact of a value chain approach on the sustainability of solid waste management in Mukuru Kwa njenga informal settlements Nairobi, Kenya

En un mundo altamente urbanizado, la gestión de residuos sólidos es un problema primordial en toda ciudad. Las ciudades de paises en desarrollo deben además afrontar retos que no afectan a las ciudades de paises desarrollados. En los paises en desarrollo muchas municipalidades sufren un crecimiento descontrolado de los asentamientos informales sin planificación urbana que hace muy complicada una adecuada gestión de los residuos sólidos urbanos, situación que se agrava al no contar estas con suficientes recursos económicos para llevar a cabo su responsabilidad en cuanto a provisión del sevicio básico de recogida de residuos. La provisión de servicio de recogida de residuos por parte de SHGs (grupos de ayuda comunitarios) en estos asentamientos informales puede ayudar a resolver algunos de estos problemas. Para que esta oportunidad sea completamente explotada, los ingresos de estos grupos deben ser garantizados, teniendo en cuenta que la sostenibilidad de estos grupos depende enteramente de ello. Este estudio pretende averiguar cómo un enfoque de cadena de valor puede mejorar la sostenibilidad de la gestión de residuos sólidos, permitiendo asegurar los ingresos de los recolectores informales de residuos. El estudio propondrá después de analizado el actual sistema, mejoras que permitan desarrollar un medio ambiente saludable en los asentamientos informales donde se desarrolla el estudio. Para alcanzar este objetivo, se ha desarrollado una investigación específica en Nairobi (Kenia) en el asentamiento precario de Mukuru Kwa Njenga, analizando los distintos aspectos relevantes que tienen influencia en una gestión integrada de residuos sólidos y las relaciones entre los distintos actores que tienen influencia en la misma.

Coastal Urban Flood Resislience versus Climate Change

Processes of founding and expanding cities in coastal areas have undergone great changes over time driven by environmental conditions. Coastal settlements looked for places above flood levels and away from swamps and other wetlands whenever possible. As populations grew, cities were extending trying to avoid low and wet lands. No city has been able to limit its growth. The risk of flooding can never be eliminated, but only reduced to the extent possible. Flooding of coastal areas is today dramatically attributed to eustasic sea level rise caused by global climate change. This can be inaccurate. Current climate change is generating an average sea level upward trend, but other regional and local factors result in this trend being accentuated in some places or attenuated, and even reversed, in others. Then, the intensity and frequency of coastal flooding around the planet, although not so much as a unique result of this general eustasic elevation, but rather of the superposition of marine and crustal dynamic elements, the former also climate-related, which give rise to a temporary raising in average sea level in the short term. Since the Little Ice Age the planet has been suffering a global warming change leading to sea level rise. The idea of being too obeying to anthropogenic factors may be attributed to Arrhenius (1896), though it is of much later highlight after the sixties of the last century. Never before, the human factor had been able of such an influence on climate. However, other types of changes in sea levels became apparent, resulting from vertical movements of the crust, modifications of sea basins due to continents fracturing, drifting and coming together, or to different types of climate patterns. Coastal zones are then doubly susceptible to floods. Precipitation immediately triggers pluvial flooding. If it continues upland or when snow and glaciers melt eventually fluvial flooding can occur. The urban development presence represents modifying factors. Additional interference is caused by river and waste water drainage systems. Climate also influences sea levels in coastal areas, where tides as well as the structure and dynamic of the geoid and its crust come into play. From the sea, waters can flood and break or push back berms and other coastline borders. The sea level, controlling the mouth of the main channel of the basin's drainage system, is ultimately what governs flood levels. A temporary rise in sea level acts as a dam at the mouth. Even in absence of that global change, so, floods are likely going to increase in many urban coastal areas. Some kind of innovative methodologies and practices should be needed to get more flood resilience cities

Integral Bridge for High-Speed Railway

The structural continuity of fully integral bridges entails many advantages and some drawbacks. Among the latter, the cyclic expansions and contractions of the deck caused by seasonal thermal variations impose alternating displacements at the piers and abutments, with effects that may be difficult to establish reliably. The advantages include easier construction and cheaper maintenance but, especially, horizontal loads can be transmitted to the ground in a much better way than in conventional bridges. This paper first presents a methodology for dealing with the problems that the cyclic displacements imposed raise at the abutments and at the bridge piers. At the former, large pressures may develop, possibly accompanied by undesirable surface settlements. At the latter, the degree of cracking and the ability to carry the specified loads may be in question. Having quantified the drawbacks, simplified but realistic analyses are conducted of the response of an integral bridge to braking and seismic loads. It is shown that integral bridges constitute an excellent alternative in the context of the requirements posed by new high-speed railway lines.

Numerical analysis of mixe-mode fracture of brickwork masonry with embedded discontinuity elements

One of the common pathologies of brickwork masonry structural elements and walls is the cracking associated with the differential settlements and/or excessive deflections of the slabs along the life of the structure. The scarce capacity of the masonry in order to accompany the structural elements that surround it, such as floors, beams or foundations, in their movements makes the brickwork masonry to be an element that frequently presents this kind of problem. This problem is a fracture problem, where the wall is cracked under mixed mode fracture: tensile and shear stresses combination, under static loading. Consequently, it is necessary to advance in the simulation and prediction of brickwork masonry mechanical behaviour under tensile and shear loading. The quasi-brittle behaviour of the brickwork masonry can be studied using the cohesive crack model whose application to other quasibrittle materials like concrete has traditionally provided very satisfactory results.

Problemas de interacción suelo estructura en cimentaciones y muros de contención. Influencia de los fenómenos de despegue y deslizamiento

Los terremotos constituyen una de las más importantes fuentes productoras de cargas dinámicas que actúan sobre las estructuras y sus cimentaciones. Cuando se produce un terremoto la energía liberada genera movimientos del terreno en forma de ondas sísmicas que pueden provocar asientos en las cimentaciones de los edificios, empujes sobre los muros de contención, vuelco de las estructuras y el suelo puede licuar perdiendo su capacidad de soporte. Los efectos de los terremotos en estructuras constituyen unos de los aspectos que involucran por su condición de interacción sueloestructura, disciplinas diversas como el Análisis Estructural, la Mecánica de Suelo y la Ingeniería Sísmica. Uno de los aspectos que han sido poco estudiados en el cálculo de estructuras sometidas a la acciones de los terremotos son los efectos del comportamiento no lineal del suelo y de los movimientos que pueden producirse bajo la acción de cargas sísmicas, tales como posibles despegues y deslizamientos. En esta Tesis se estudian primero los empujes sísmicos y posibles deslizamientos de muros de contención y se comparan las predicciones de distintos tipos de cálculos: métodos pseudo-estáticos como el de Mononobe-Okabe (1929) con la contribución de Whitman-Liao (1985), y formulaciones analíticas como la desarrollada por Veletsos y Younan (1994). En segundo lugar se estudia el efecto del comportamiento no lineal del terreno en las rigideces de una losa de cimentación superficial y circular, como la correspondiente a la chimenea de una Central Térmica o al edificio del reactor de una Central Nuclear, considerando su variación con frecuencia y con el nivel de cargas. Finalmente se estudian los posibles deslizamientos y separación de las losas de estas dos estructuras bajo la acción de terremotos, siguiendo la formulación propuesta por Wolf (1988). Para estos estudios se han desarrollado una serie de programas específicos (MUROSIS, VELETSOS, INTESES y SEPARSE) cuyos listados y detalles se incluyen en los Apéndices. En el capítulo 6 se incluyen las conclusiones resultantes de estos estudios y recomendaciones para futuras investigaciones. ABSTRACT Earthquakes constitute one of the most important sources of dynamic loads that acting on structures and foundations. When an earthquake occurs the liberated energy generates seismic waves that can give rise to structural vibrations, settlements of the foundations of buildings, pressures on retaining walls, and possible sliding, uplifting or even overturning of structures. The soil can also liquefy losing its capacity of support The study of the effects of earthquakes on structures involve the use of diverse disciplines such as Structural Analysis, Soil Mechanics and Earthquake Engineering. Some aspects that have been the subject of limited research in relation to the behavior of structures subjected to earthquakes are the effects of nonlinear soil behavior and geometric nonlinearities such as sliding and uplifting of foundations. This Thesis starts with the study of the seismic pressures and potential displacements of retaining walls comparing the predictions of two types of formulations and assessing their range of applicability and limitations: pseudo-static methods as proposed by Mononobe-Okabe (1929), with the contribution of Whitman-Liao (1985), and analytical formulations as the one developed by Veletsos and Younan (1994) for rigid walls. The Thesis deals next with the effects of nonlinear soil behavior on the dynamic stiffness of circular mat foundations like the chimney of a Thermal Power Station or the reactor building of a Nuclear Power Plant, as a function of frequency and level of forces. Finally the seismic response of these two structures accounting for the potential sliding and uplifting of the foundation under a given earthquake are studied, following an approach suggested by Wolf (1988). In order to carry out these studies a number of special purposes computer programs were developed (MUROSIS, VELETSOS, INTESES and SEPARSE). The listing and details of these programs are included in the appendices. The conclusions derived from these studies and recommendations for future work are presented in Chapter 6.

Los recursos medioambientales aplicados a la arquitectura contemporánea en vivienda aislada

Objetivos. Análisis a través del prisma de la sostenibilidad, con un triple objetivo: consumo de energía, aspecto constructivo y recursos arquitectónicos, de algunos ejemplos destacados de vivienda aislada desde 1973, crisis del petróleo, hasta el cambio ideológico del 11 de septiembre de 2001. Emplazadas en microclimas semejantes en distintas latitudes, para extrapolar al clima mediterráneo. Ejemplos. Siete viviendas aisladas de distinto diseño conceptual, situadas en climas subtropicales, en ecosistemas variados pero de concepción medioambiental, constructiva y arquitectónica muy actual. Los ejemplos elegidos, por su intencionalidad, su diseño, y su sentido utilitario, constructivo y semiótico, se analizan desde el hecho acumulativo y el hecho reactivo, mediante el procedimiento de contrastar diversas fuentes de información. Objetivos. El análisis de cada una de las viviendas procedentes de diferentes arquitectos, se hace mediante la simulación de modelos que permitan describir la parte esencial del comportamiento de un sistema de interés, así como diseñar y realizar experimentos con el modelo para extraer conclusiones de sus resultados y apoyar la toma de decisiones proyectual. Procedimiento. En una primera fase, el medio natural queda definido por su localización, interpretación del lugar, el clima concreto (mediante climogramas generales y de isopletas), determinando un diagnóstico medioambiental para el establecimiento de estrategias a partir de los datos experimentales a contrastar con el resultado finalmente obtenido. En una segunda fase se eligen los casos más representativos de LowTech / LowEnergy y HighTech / HighEnergy. Se realiza un análisis del modelo, frente a uno de los elementos predominantes: sol, aire, agua, tierra, luna, vegetación y miscelánea. Resultados. De los casos estudiados se extraen principios aplicables en cada uno de los ámbitos: medioambiental, relacionados con la adaptabilidad energética; constructivo, en relación con la economía; y arquitectónico, vinculado con lo social, con una perspectiva diferente sobre los nuevos espacios vivibles. Conclusiones y relevancia. En los emplazamientos estudiados, los arquitectos herederos del movimiento moderno, han utilizado los recursos medioambientales pasivos y activos más actuales en cada uno de los elementos, así como la orientación, la ventilación, la radiación, la inercia térmica,…las actitudes más contemporáneas como expertos bioclimáticos. Los principios extraídos deben facilitar un proceso proyectual mediante pautas experimentales a desarrollar sin un uso desmesurado de la tecnología. Los principios y las conclusiones obtenidos servirán de aplicación a nuevos modelos conociendo los parámetros más relevantes. La modelización analógica - digital permitirá evaluar el comportamiento más aplicable según las necesidades a satisfacer. Objectives. Architectural analysis through the prism of sustainability with three aims: energy consumption, building technique and architectonical resources. The study is focused on some key examples of low density houses since 1973 (featured by the Oil crisis) until the 11th September 2001´s ideological change. These living spaces are settled in similar microclimates although in different latitudes with strong possibilities for applications in Mediterranean climates. Examples. Seven remote detached dwellings with different conceptual characters, located in subtropical climates, in different ecosystems, however with a sustainable basis and architectonical building concepts very updated. The cultural objects chosen, due to legitimate reasons such as: purpose, a plan, an utilitarian sense, constructive and semiotic, are analyzed under an accumulative perspective along with the reactive fact as the procedure to contrast and compare different sources of information. Goals. The analysis of the examples of different architects, will be done in order to simulate through models which describe and display the essential part of behaviour that corresponds to an interest system, along with the design and to try out or experiment with the model and to draw up results which support the projecting decision process. Procedure. On a first stage, the natural environment is shaped by its location, interpretation of the pace, a particular climate (through general climograms and isophlets), determining an environmental diagnosis which would be able to generate scientific conclusions in order to develop adequate strategies. Hence from experimental data we contrast with the results. On a second stage the more representative cases of LowTech / LowEnergy and HighTech / HighEnergy are choosen. We analyze the model taking into consideration and facing a key element: sun, air, water, soil, moon, vegetation and miscellany. Results. From the study cases we draw up applicable principles in each field: the ecological in relation with energetic adaptability, the constructive potential related with economy, and the social in relation with a different perspective about new architectural living spaces. Conclusions and Relevance. On those settlements studied, the heirs architects from Modern Movement, had used the passive and active, updated environmental resources in each element. For instance, aspects like orientation, ventilation, solar radiation, thermal inertia…, and the most contemporary attitude as bioclimatic expert that they are. These principles speed up through experimental guidelines, the technology is diminished and the design process be provided. The principles and conclusions generated will be useful in order to apply new models because we are able to know the most relevant key parameters. The analogical-digital modelizations allow us to revaluate the applicable behaviour according to the needs to satisfy.

Análisis de la influencia de distintos diseños de paraguas de micropilotes, pantalla de micropilotes, paraguas de jet grouting y pantallas de jet grouting en los asientos en superficie durante la ejecución de túneles perforados superficialmente

Ya en el informe acerca del estado de la tecnología en la excavación profunda y en la construcción de túneles en terreno duro presentado en la 7ª Conferencia en Mecánica de Suelos e Ingeniería de la Cimentación, Peck (1969) introdujo los tres temas a ser tenidos en cuenta para el diseño de túneles en terrenos blandos: o Estabilidad de la cavidad durante la construcción, con particular atención a la estabilidad del frente del túnel; o Evaluación de los movimientos del terreno inducidos por la construcción del túnel y de la incidencia de los trabajos subterráneos a poca profundidad sobre los asentamientos en superficie; o Diseño del sistema de sostenimiento del túnel a instalar para asegurar la estabilidad de la estructura a corto y largo plazo. Esta Tesis se centra en los problemas señalados en el segundo de los puntos, analizando distintas soluciones habitualmente proyectadas para reducir los movimientos inducidos por la excavación de los túneles. El objeto de la Tesis es el análisis de la influencia de distintos diseños de paraguas de micropilotes, pantalla de micropilotes, paraguas de jet grouting y pantallas de jet grouting en los asientos en superficie durante la ejecución de túneles ejecutados a poca profundidad, con objeto de buscar el diseño que optimice los medios empleados para una determinada reducción de asientos. Para ello se establecen unas premisas para los proyectistas con objeto de conocer a priori cuales son los tratamientos más eficientes (de los propuestos en la Tesis) para la reducción de asientos en superficie cuando se ha de proyectar un túnel, de tal manera que pueda tener datos cualitativos y algunos cuantitativos sobre los diseños más óptimos, utilizando para ello un programa de elementos finitos de última generación que permite realizara la simulación tensodeformación del terreno mediante el modelo de suelo con endurecimiento (Hardening Soil Small model), que es una variante elastoplástica del modelo hiperbólico, similar al Hardening Soil Model. Además, este modelo incorpora una relación entre deformación y el modulo de rigidez, simulando el diferente comportamiento del suelo para pequeñas deformaciones (por ejemplo vibraciones con deformaciones por debajo de 10-5 y grandes deformaciones (deformaciones > 10-3). Para la realización de la Tesis se han elegido cinco secciones de túnel, dos correspondiente a secciones tipo de túnel ejecutado con tuneladora y tres secciones ejecutados mediante convencionales (dos correspondientes a secciones que han utilizado el método Belga y una que ha utilizado el NATM). Para conseguir los objetivos marcados, primeramente se ha analizado mediante una correlación entre modelos tridimensionales y bidimensionales el valor de relajación usado en estos últimos, y ver su variación al cambio de parámetros como la sección del túnel, la cobertera, el procedimiento constructivo, longitud de pase (métodos convencionales) o presión del frente (tuneladora) y las características geotécnicas de los materiales donde se ejecuta el túnel. Posteriormente se ha analizado que diseño de pantalla de protección tiene mejor eficacia respecto a la reducción de asientos, variando distintos parámetros de las características de la misma, como son el empotramiento, el tipo de micropilotes o pilote, la influencia del arriostramiento de las pantallas de protección en cabeza, la inclinación de la pantalla, la separación de la pantalla al eje del túnel y la disposición en doble fila de la pantalla de pantalla proyectada. Para finalizar el estudio de la efectividad de pantalla de protección para la reducción de asiento, se estudiará la influencia de la sobrecarga cercanas (simulación de edificios) tiene en la efectividad de la pantalla proyectada (desde el punto de vista de reducción de movimientos en superficie). Con objeto de poder comparar la efectividad de la pantalla de micropilotes respecto a la ejecución de un paraguas de micropilotes se ha analizado distintos diseños de paraguas, comparando el movimiento obtenido con el obtenido para el caso de pantalla de micropilotes, comparando ambos resultados con los medidos en obras ya ejecutadas. En otro apartado se ha realizado una comparación entre tratamientos similar, comparándolos en este caso con un paraguas de jet grouting y pantallas de jet grouting. Los resultados obtenidos se han con valores de asientos medidos en distintas obras ya ejecutadas y cuyas secciones se corresponden a los empleados en los modelos numéricos. Since the report on the state of technology in deep excavation and tunnelling in hard ground presented at the 7th Conference on Soil Mechanics and Foundation Engineering, Peck (1969) introduced the three issues to be taken into account for the design of tunnels in soft ground: o Cavity Stability during construction, with particular attention to the stability of the tunnel face; o Evaluation of ground movements induced by tunnelling and the effect of shallow underground workings on surface settlement; o Design of the tunnel support system to be installed to ensure short and long term stability of the structure. This thesis focuses on the issues identified in the second point, usually analysing different solutions designed to reduce the movements induced by tunnelling. The aim of the thesis is to analyse the influence of different micropile forepole umbrellas, micropile walls, jet grouting umbrellas and jet grouting wall designs on surface settlements during near surface tunnelling in order to use the most optimal technique to achieve a determined reduction in settlement. This will establish some criteria for designers to know a priori which methods are most effective (of those proposed in the thesis) to reduce surface settlements in tunnel design, so that it is possible to have qualitative and some quantitative data on the optimal designs, using the latest finite element modelling software that allows simulation of the ground’s infinitesimal strain behaviour using the Hardening Soil Small Model, which is a variation on the elasto-plastic hyperbolic model, similar to Hardening Soil model. In addition, this model incorporates a relationship between strain and the rigidity modulus, simulating different soil behaviour for small deformations (eg deformation vibrations below 10-5 and large deformations (deformations > 10-3). For the purpose of this thesis five tunnel sections have been chosen, two sections corresponding to TBM tunnels and three sections undertaken by conventional means (two sections corresponding to the Belgian method and one corresponding to the NATM). To achieve the objectives outlined, a correlation analysis of the relaxation values used in the 2D and 3D models was undertaken to verify them against parameters such as the tunnel cross-section, the depth of the tunnel, the construction method, the length of step (conventional method) or face pressure (TBM) and the geotechnical characteristics of the ground where the tunnel is constructed. Following this, the diaphragm wall design with the greatest efficiency regarding settlement reduction was analysed, varying parameters such as the toe depth, type of micropiles or piles, the influence of bracing of the head protection diaphragm walls, the inclination of the diaphragm wall, the separation between the diaphragm wall and the tunnel axis and the double diaphragm wall design arrangement. In order to complete the study into the effectiveness of protective diaphragm walls ofn the reduction of settlements, the influence of nearby imposed loads (simulating buildings) on the effectiveness of the designed diaphragm walls (from the point of view of reducing surface movements) will be studied. In order to compare the effectiveness of micropile diaphragm walls regarding the installation of micropile forepole umbrellas, different designs of these forepole umbrellas have been analysed comparing the movement obtained with that obtained for micropiled diaphragm walls, comparing both results with those measured from similar completed projects. In another section, a comparison between similar treatments has been completed, comparing the treatments with a forepole umbrella by jet grouting and jet grouting walls. The results obtained compared with settlement values measured in various projects already completed and whose sections correspond to those used in the numerical models.

GIS analysis for the study of rural depopulation: the Kingdom of Valencia (Tomas Lopez 1789)

One of the more aspects that have shaped the landscape is the human impact. The human impact has the clearest indicator of the density of settlements in a particular geographic region. In this paper we study all settlements shown on the map of the Kingdom of Valencia, Spain Geographic Atlas (AGE) of Tomas Lopez (1788), and their correspondence with the current ones. To meet this goal we have developed a specific methodology, the systematic study of all existing settlements in historical cartography. This will determine which have disappeared and which have been renamed. The material used has been the historical cartography of Tomas Lopez, part of the AGE (1789), the Kingdom of Valencia (1789), sheets numbers (78, 79, 80 and 81); Current mapping of the provinces of Alicante, Valencia, Castellon, Teruel, Tattagona and Cuenca; As main software ArcGis V.9.3. The steps followed in the methodology are as follows: 1. Check the scale of the maps. Analyze the possible use of a spherical earth model. 2. Geo-reference of maps with latitude and longitude framework. Move the historical longitude origin to the origin longitude of modern cartography. 3 Digitize of all population settlements or cities. 4 Identify historic settlements or cities corresponding with current ones. 5. If the maps have the same orientation and scale, replace the coordinate transformation of historical settlements with a new one, by a translation in latitude and longitude equal to the calculated mean value of all ancient map points corresponding to the new. 6. Calculation of absolute accuracy of the two maps, i.e. the linear distance between the points of both maps. 7 draw in the GIS, the settlements without correspondence, in the current coordinates, and with a circle of mean error of the sheet, in order to locate their current location. If there are actual settlements exist within this circle, they are candidates to be the searched settlements. We analyzed more than 2000 settlements represented in the Atlas of Tomas Lopez of the Kingdom of Valencia (1789), of which almost 14.5% have no correspondence with the existing settlements. The rural landscape evolution of the Valencia, oldest kingdom of Valencia, one can say that can be severely affected by the anthropization suffered in the period from 1789 to the present, since 70% of existing settlements actually have appeared after Tomas Lopez¿s cartography, dated on 1789

Un retrato de la mujer suburbial en el cine

En las últimas décadas hemos visto como han proliferado en la periferia de nuestras ciudades grandes extensiones de asentamientos residenciales. Este modelo urbanístico se ha demostrado no solo lesivo para el medio ambiente sino además ideológicamente erróneo. Concebido en EE.UU. como respuesta a la demanda de bienestar de una reciente clase media, su tipología fue penetrando paulatinamente en la ciudad europea a través del cine. Basada en premisas poco flexibles, pronto se revelaría como un modelo insatisfactorio para la mujer a la que en teoría iba dirigida. In recent decades we have experienced how large extensions of residential settlements have proliferated in the periphery of our cities. This urban model has been shown not only harmful to the environment but also ideologically wrong. Designed in the USA in response to the demand for welfare of an emerging middle class, their typology was gradually penetrating the European city through cinema. Based on inflexible assumptions, it was soon revealed as an unsatisfactory model for women to whom it was theoretically addressed.

Diseño basado en técnicas de fiabilidad del tratamiento de mejora del terreno mediante columnas de grava

El proyecto geotécnico de columnas de grava tiene todas las incertidumbres asociadas a un proyecto geotécnico y además hay que considerar las incertidumbres inherentes a la compleja interacción entre el terreno y la columna, la puesta en obra de los materiales y el producto final conseguido. Este hecho es común a otros tratamientos del terreno cuyo objetivo sea, en general, la mejora “profunda”. Como los métodos de fiabilidad (v.gr., FORM, SORM, Monte Carlo, Simulación Direccional) dan respuesta a la incertidumbre de forma mucho más consistente y racional que el coeficiente de seguridad tradicional, ha surgido un interés reciente en la aplicación de técnicas de fiabilidad a la ingeniería geotécnica. Si bien la aplicación concreta al proyecto de técnicas de mejora del terreno no es tan extensa. En esta Tesis se han aplicado las técnicas de fiabilidad a algunos aspectos del proyecto de columnas de grava (estimación de asientos, tiempos de consolidación y aumento de la capacidad portante) con el objetivo de efectuar un análisis racional del proceso de diseño, considerando los efectos que tienen la incertidumbre y la variabilidad en la seguridad del proyecto, es decir, en la probabilidad de fallo. Para alcanzar este objetivo se ha utilizado un método analítico avanzado debido a Castro y Sagaseta (2009), que mejora notablemente la predicción de las variables involucradas en el diseño del tratamiento y su evolución temporal (consolidación). Se ha estudiado el problema del asiento (valor y tiempo de consolidación) en el contexto de la incertidumbre, analizando dos modos de fallo: i) el primer modo representa la situación en la que es posible finalizar la consolidación primaria, parcial o totalmente, del terreno mejorado antes de la ejecución de la estructura final, bien sea por un precarga o porque la carga se pueda aplicar gradualmente sin afectar a la estructura o instalación; y ii) por otra parte, el segundo modo de fallo implica que el terreno mejorado se carga desde el instante inicial con la estructura definitiva o instalación y se comprueba que el asiento final (transcurrida la consolidación primaria) sea lo suficientemente pequeño para que pueda considerarse admisible. Para trabajar con valores realistas de los parámetros geotécnicos, los datos se han obtenido de un terreno real mejorado con columnas de grava, consiguiendo, de esta forma, un análisis de fiabilidad más riguroso. La conclusión más importante, obtenida del análisis de este caso particular, es la necesidad de precargar el terreno mejorado con columnas de grava para conseguir que el asiento ocurra de forma anticipada antes de la aplicación de la carga correspondiente a la estructura definitiva. De otra forma la probabilidad de fallo es muy alta, incluso cuando el margen de seguridad determinista pudiera ser suficiente. En lo que respecta a la capacidad portante de las columnas, existen un buen número de métodos de cálculo y de ensayos de carga (tanto de campo como de laboratorio) que dan predicciones dispares del valor de la capacidad última de las columnas de grava. En las mallas indefinidas de columnas, los resultados del análisis de fiabilidad han confirmado las consideraciones teóricas y experimentales existentes relativas a que no se produce fallo por estabilidad, obteniéndose una probabilidad de fallo prácticamente nula para este modo de fallo. Sin embargo, cuando se analiza, en el contexto de la incertidumbre, la capacidad portante de pequeños grupos de columnas bajo zapatas se ha obtenido, para un caso con unos parámetros geotécnicos típicos, que la probabilidad de fallo es bastante alta, por encima de los umbrales normalmente admitidos para Estados Límite Últimos. Por último, el trabajo de recopilación sobre los métodos de cálculo y de ensayos de carga sobre la columna aislada ha permitido generar una base de datos suficientemente amplia como para abordar una actualización bayesiana de los métodos de cálculo de la columna de grava aislada. El marco bayesiano de actualización ha resultado de utilidad en la mejora de las predicciones de la capacidad última de carga de la columna, permitiendo “actualizar” los parámetros del modelo de cálculo a medida que se dispongan de ensayos de carga adicionales para un proyecto específico. Constituye una herramienta valiosa para la toma de decisiones en condiciones de incertidumbre ya que permite comparar el coste de los ensayos adicionales con el coste de una posible rotura y , en consecuencia, decidir si es procedente efectuar dichos ensayos. The geotechnical design of stone columns has all the uncertainties associated with a geotechnical project and those inherent to the complex interaction between the soil and the column, the installation of the materials and the characteristics of the final (as built) column must be considered. This is common to other soil treatments aimed, in general, to “deep” soil improvement. Since reliability methods (eg, FORM, SORM, Monte Carlo, Directional Simulation) deals with uncertainty in a much more consistent and rational way than the traditional safety factor, recent interest has arisen in the application of reliability techniques to geotechnical engineering. But the specific application of these techniques to soil improvement projects is not as extensive. In this thesis reliability techniques have been applied to some aspects of stone columns design (estimated settlements, consolidation times and increased bearing capacity) to make a rational analysis of the design process, considering the effects of uncertainty and variability on the safety of the project, i.e., on the probability of failure. To achieve this goal an advanced analytical method due to Castro and Sagaseta (2009), that significantly improves the prediction of the variables involved in the design of treatment and its temporal evolution (consolidation), has been employed. This thesis studies the problem of stone column settlement (amount and speed) in the context of uncertainty, analyzing two failure modes: i) the first mode represents the situation in which it is possible to cause primary consolidation, partial or total, of the improved ground prior to implementation of the final structure, either by a pre-load or because the load can be applied gradually or programmed without affecting the structure or installation; and ii) on the other hand, the second mode implies that the improved ground is loaded from the initial instant with the final structure or installation, expecting that the final settlement (elapsed primary consolidation) is small enough to be allowable. To work with realistic values of geotechnical parameters, data were obtained from a real soil improved with stone columns, hence producing a more rigorous reliability analysis. The most important conclusion obtained from the analysis of this particular case is the need to preload the stone columns-improved soil to make the settlement to occur before the application of the load corresponding to the final structure. Otherwise the probability of failure is very high, even when the deterministic safety margin would be sufficient. With respect to the bearing capacity of the columns, there are numerous methods of calculation and load tests (both for the field and the laboratory) giving different predictions of the ultimate capacity of stone columns. For indefinite columns grids, the results of reliability analysis confirmed the existing theoretical and experimental considerations that no failure occurs due to the stability failure mode, therefore resulting in a negligible probability of failure. However, when analyzed in the context of uncertainty (for a case with typical geotechnical parameters), results show that the probability of failure due to the bearing capacity failure mode of a group of columns is quite high, above thresholds usually admitted for Ultimate Limit States. Finally, the review of calculation methods and load tests results for isolated columns, has generated a large enough database, that allowed a subsequent Bayesian updating of the methods for calculating the bearing capacity of isolated stone columns. The Bayesian updating framework has been useful to improve the predictions of the ultimate load capacity of the column, allowing to "update" the parameters of the calculation model as additional load tests become available for a specific project. Moreover, it is a valuable tool for decision making under uncertainty since it is possible to compare the cost of further testing to the cost of a possible failure and therefore to decide whether it is appropriate to perform such tests.

Reacting and Recycling

To a certain extent what this research is proposing is a return to local principles or to regionalism, which is able to employ place-specific tools and craftsmanship (local arts and their virtues) promoting and being innovative with traditional elements which belong to a particular place, and using tectonic and stereotomic logic. You can observe this, in the face of a destructive natural event. An immediate architectural reaction is produced in cooperation with the rest of the not affected territory. The cooperation of certain non-governmental organizations with other groups in the same collaborative cycle improves the recycling of ideas and city planning forms. These organizations cooperate in the development and implementation of cities and settlements that need a fast reaction when facing an unexpected disaster.

Dynamic & Cyclic behaviour of ballast in the long term as determined in Cedex's track box

The 6 cylinder servo-hydraulic loading system of CEDEX's track box (250 kN, 50 Hz) has been recently implemented with a new piezoelectric loading system (±20 kN, 300 Hz) allowing the incorporation of low amplitude high frequency dynamic load time histories to the high amplitude low frequency quasi-static load time histories used so far in the CEDEX's track box to assess the inelastic long term behavior of ballast under mixed traffic in conventional and high- speed lines. This presentation will discuss the results obtained in the first long-duration test performed at CEDEX's track box using simultaneously both loading systems, to simulate the pass-by of 6000 freight vehicles (1M of 225 kN axle loads) travelling at a speed of 120 km/h over a line with vertical irregularities corresponding to a medium quality lin3e level. The superstructure of the track tested at full scale consisted of E 60 rails, stiff rail pads (mayor que 450 kN/mm), B90.2 sleepers with USP 0.10 N/mm and a 0.35 m thick ballast layer of ADIF first class. A shear wave velocity of 250 m/s can be assumed for the different layers of the track sub-base. The ballast long-term settlements will be compared with those obtained in a previous long-duration quasi- static test performed in the same track, for the RIVAS [EU co-funded] project, in which no dynamic loads where considered. Also, the results provided by a high diameter cyclic triaxial cell with ballast tested in full size will be commented. Finally, the progress made at CEDEX's Geotechnical Laboratory to reproduce numerically the long term behavior of ballast will be discussed.

La habitación subterránea en la Península Ibérica : investigación geológica

La habitación rupestre en la Península Ibérica conforma un amplio conjunto de manifestaciones cuyos orígenes son difíciles de dilucidar. Existen conjuntos primitivos, posiblemente horadados durante la Antigüedad Clásica y Tardía, y otros que probablemente se originaron y excavaron en la Alta Edad Media, en los que se mezclan grupos de origen religioso y otros de probable uso defensivo. El conjunto peninsular es sin duda el más variado de Europa Occidental, pues recibió influencias árabes y usos de la cristiandad antigua, importados de Oriente Próximo, que por tanto relacionan estas manifestaciones con otras del arco mediterráneo. La supervivencia del uso de las cuevas a lo largo de la Baja Edad Media -una vez afianzada la Reconquista- es una incógnita, pero los usos rupestres volvieron a generalizarse en ciertos sectores de la Península durante la Edad Moderna, toda vez que el hábitat cuevero manifestó una eclosión relacionada con la peripecia de los moriscos, primero desterrados de sus habitaciones en el Sur y Este peninsular y luego expulsados en los albores del siglo XVII. Los que quedaron, nominalmente conversos, debieron habitar de nuevo cuevas en sus lugares de origen. Esos núcleos son los más abundantes, particularmente en la provincia de Granada y aledañas. Este substrato fue seguramente el punto de apoyo para la proliferación de las cuevas de habitación a partir del siglo XIX, en el cual un creciente proletariado agrícola y urbano necesitó de alojamientos baratos y no hizo sino imitar usos preexistentes, que se pueden rastrear en muchos de los núcleos rupestres que sobrevivieron mayoritariamente hasta bien entrado el siglo XX, y que se abandonaron gradualmente a partir de los años 60 de esa centuria. Para entonces, existían barrios de cuevas extensos en muchas provincias, destacando, aparte de las andaluzas, ciertas zonas de la Cuenca del Ebro (aragonesa, navarra y riojana), del arco periurbano de Valencia, del Sur de Madrid, de la Mancha toledana, o de las provincias de Albacete, Guadalajara, Murcia e incluso de Palencia. Los núcleos antiguos se excavaron -en razón de su origen dedicado a defensa y refugio- en lugares poco accesibles, que mayoritariamente se dan en relieves anfractuosos, en las orlas marginales detríticas y carbonatadas de las cuencas terciarias y en terrenos más antiguos de la geológicamente denominada Cuenca Vasco Cantábrica, en las cuales florecieron centros de eremitismo del primitivo condado de Castilla. También son lugares inaccesibles los riscos asomados a cantiles fluviales, cuya regularización morfológica natural ha sido causa de la ruina de múltiples hipogeos que se labraron con las mismas intenciones de refugio, defensa o retiro espiritual. Los núcleos modernos se han excavado ya en terrenos más propicios (los que componen las cuencas terciarias o "España arcillosa", mayoritariamente), y por ello observamos cómo abundan las litologías sedimentarias, que son aquellas en las que se horadaron casi todas las "colmenas" de habitación moderna en la Península. En unos casos y otros, existen rasgos comunes en lo relativo a la litología y comportamiento de los materiales excavados, y también en lo relativo a su evolución, meteorización y conservación. Se han estudiado por ello estas pautas comunes -como un posible avance para el establecimiento futuro de estudios de geoconservación del patrimonio rupestre habitado-, que se traducen en la determinación de los procesos de meteorización más característicos en los antros de la Península Ibérica -sean modernos o antiguos- y en la determinación de las relaciones más habituales entre geomorfología y tipología de las cuevas de habitación. También se exponen algunas conclusiones relativas a la resistencia de los tipos pétreos en relación a la antigüedad de los emplazamientos. Esta relación se explica bien si tenemos en cuenta que las cuevas antiguas trataban de ser lugares apartados en los que dominan rocas más resistentes -como se ha explicado- y que en las modernas se ha buscado la habitación permanente, en los materiales más blandos ocupan las depresiones terciarias del Centro, Este y Sur de la Península, colonizados no ya como refugios sino de modo seguro, y ya en arrabales "extramuros" de las ciudades. Geomorfológicamente, esta razón histórica tiene consecuencias sobre la posición de las cuevas, sobre su organización, y sobre su conservación. La extensión del dominio estudiado obliga prácticamente a bosquejar algunas de estas conclusiones geológicas, pero permite a su vez proporcionar una visión global acerca del patrimonio troglodítico desde una perspectiva geológica, y en ello radica la principal novedad de la investigación. Cave dwelling in the Iberian Peninsula comprises a great deal of examples whose origins are sometimes difficult to elucidate. There are primitive groups of caves, probably belonging to Classical and Late Antiquity, and other settlements that appear to have been created and excavated in the Early Middle Ages. Some of them are due to religious reasons and some others may probably have served for defensive uses. The Peninsular group is very likely the most diverse in Western Europe, for it was not only influenced by Arabs, but it also assimilated uses from the Antique Christendom, imported from the Middle East. In this sense, Iberian cave dwellings connect with those of the Mediterranean area. There is not total certainty about the survival of caves serving for dwelling throughout the Late Middle Ages, once the Reconquista was a fact. However, underground excavations for human habitation were once again dispread in certain zones of the Peninsula during the Early Modern period. This growth of underground habitats appears in connexion with Morisco’s vicissitudes; first of all, their removal from their settlements in South and Eastern Peninsula, and finally their expulsion from Spanish territory at the very beginning of XVII th century. Those of them who rested in Spain –and that were nominally “converts”- seem to have returned to cave dwelling in their places of origin, particularly in the province of Granada and its neighbouring zones. This substrate may have been the toehold for a new spreading of cave dwellings since XIX th century, when the increasing rural and urban proletariat returned to the pre-existent uses of caves in order to solve the necessity of affordable housing. This fact can still be detected in many of the rock settlements that have survived during a great part of the XX th century and which were gradually abandoned from the 60´s onwards. There were important cave dwelling districts in many Spanish territories by that time, and not only in Andalusia. We also find them in certain areas of the Ebro basin (those of Aragon, Navarra and La Rioja), in the peri-urban arc of Valencia, in the South of Madrid province and also in the provinces of Toledo (the so called “Mancha toledana”), Albacete, Guadalajara, Murcia or even Palencia as well. Due to their defensive and refuge uses, primitive underground habitats were dug in hardly accessible places. The majority of them are located in mountainous and rough areas, when not in the marginal borders of Tertiary basins, where coarse detritic and carbonate formations outcrop. Cave dwellings can also be found in more ancient rock masses, such as those of the Basque Cantabrian Mesozoic Basin, which is the area where hermit centres of the primitive County of Castile first flourished. Cliffs surrounding fluvial valleys are as well inaccessible places, but here we find that geological evolution has caused the destruction of many rock sanctuaries and cliff dwellings that were originally dug with the same purposes of defence, refuge and spiritual retreat. Later modern cave settlements were dug in quite more favourable terrains, mainly in the soils that compose the Tertiary basins, generally known as “España arcillosa” or “Clayey Spain”. Therefore, we find abundant sedimentary fine and medium grained lithologies, which are the ones that have hosted the majority of Modern Era warren cave dwellings in the Iberian Peninsula. Actually, both types of cave dwelling share some standards regarding the lithology of the excavated materials, and they share as well certain patterns that affect to their evolution, weathering and preservation. These common patterns have been studied here in order to determine the most characteristic weathering processes that affect the majority of the Iberian caves, both Antique and Modern. And also with a view to establish the most habitual relationships between geomorphology and typology of cave dwellings. The study may as well provide a first basis for future studies on geo-preservation of cave dwellings heritage. We also reach some conclusions about the strength of different rocks concerning the antiquity of the sites. As we have already pointed out, this relation comes from the fact that ancient caves were placed in remote or isolated locations, where harder rocks outcrop, while more modern ones result from people´s search of permanent dwelling. In this sense, the softer rocks of the Tertiary Basins of Middle, East and South Peninsula provided a secure colonization to this second and modern group. And moreover, considering geomorphological features, this historical reason has had an effect not only on the position and location of the caves, but also on their organisation/structure/distribution and preservation. The huge extension of our domain of interest almost forces to sketch out some of these geological conclusions. But at the same time it gives a global panorama of Spanish troglodyte heritage, seen from a geological perspective. And here is the main novelty of this research.