Geomorphological analysis and evolution of an altered floodplain drainage system. The case of the Partido Stream (Spain)

The Partido Stream is a small torrential course that flows into the marsh of the Doñana National Park, an area that was declared a World Heritage Site in 1994. Before 1981, floods occurred, and the stream overflowed onto a floodplain. As an old alluvial fan, the floodplain has its singular orography and functionality. Fromthe floodplain, several drainage channels, locally called caño, discharged into themarsh. The Partido Streamhad themorphology of a caño and covered approximately 8 km from the old fan to the marsh. The stream was straightened and channelised in 1981 to cultivate the old fan. This resulted in floods that were concentrated between the banks in the following years, which caused the depth of water and the shear stress to increase, thus, scouring the river bed and river banks. In this case, the eroded materials were carried towards the marsh where a new alluvial fan evolved. Control measures on the old fan were implemented in 2006 to stop the development of the new alluvial fan downstream over the marsh. Thus, the stream would partially recover its original behaviour that it had before channelisation, moving forwards in a new, balanced state. The present study describes the geomorphological evolution that channelisation has caused since 1981 and the later slow process of recovery of the original hydraulic-sedimentation regime since 2006. Additionally, it deepens the understanding of the original hydraulic behaviour of the stream, combining field data and 2D simulations.

A CO2-saving-based methodology to measure the impact of the SUMP in European Cities: Application to the City of Burgos

Urban mobility in Europe is always a responsibility of the municipalities which propose measures to reduce CO2 emissions in terms of mobility aimed at reducing individual private transport (car). The European Commission's Action Plan on Urban Mobility calls for an increase in the take-up of Sustainable Urban Mobility Plans in Europe. SUMPs aim to create a sustainable urban transport system. Europe has got some long term initiatives and has been using some evaluation procedures, many of them through European projects. Nevertheless, the weak point with the SUMPs in Spain, has been the lack of concern about the evaluation and the effectiveness of the measures implemented in a SUMP. For this reason, it is difficult to know exactly whether or not the SUMPs have positively influenced in the modal split of the cities, and its contribution to reduce CO2 levels. The case of the City of Burgos is a very illustrative example as it developed a CiViTAS project during the years 2005-2009, with a total investment of 6M?. The results have been considered as ?very successful? even at European level. The modal split has changed considerably for better, The cost-effectiveness ratio of the SUMP in the city can be measured with the CO2 ton saved, specifically 36 ? per CO2 ton saved, which is fully satisfactory and in line with calculations from other European researchers. Additionally, the authors propose a single formula to measure the effectiveness of the activities developed under the umbrella of a SUMP.

Coastal Urban Flood Resislience versus Climate Change

Processes of founding and expanding cities in coastal areas have undergone great changes over time driven by environmental conditions. Coastal settlements looked for places above flood levels and away from swamps and other wetlands whenever possible. As populations grew, cities were extending trying to avoid low and wet lands. No city has been able to limit its growth. The risk of flooding can never be eliminated, but only reduced to the extent possible. Flooding of coastal areas is today dramatically attributed to eustasic sea level rise caused by global climate change. This can be inaccurate. Current climate change is generating an average sea level upward trend, but other regional and local factors result in this trend being accentuated in some places or attenuated, and even reversed, in others. Then, the intensity and frequency of coastal flooding around the planet, although not so much as a unique result of this general eustasic elevation, but rather of the superposition of marine and crustal dynamic elements, the former also climate-related, which give rise to a temporary raising in average sea level in the short term. Since the Little Ice Age the planet has been suffering a global warming change leading to sea level rise. The idea of being too obeying to anthropogenic factors may be attributed to Arrhenius (1896), though it is of much later highlight after the sixties of the last century. Never before, the human factor had been able of such an influence on climate. However, other types of changes in sea levels became apparent, resulting from vertical movements of the crust, modifications of sea basins due to continents fracturing, drifting and coming together, or to different types of climate patterns. Coastal zones are then doubly susceptible to floods. Precipitation immediately triggers pluvial flooding. If it continues upland or when snow and glaciers melt eventually fluvial flooding can occur. The urban development presence represents modifying factors. Additional interference is caused by river and waste water drainage systems. Climate also influences sea levels in coastal areas, where tides as well as the structure and dynamic of the geoid and its crust come into play. From the sea, waters can flood and break or push back berms and other coastline borders. The sea level, controlling the mouth of the main channel of the basin's drainage system, is ultimately what governs flood levels. A temporary rise in sea level acts as a dam at the mouth. Even in absence of that global change, so, floods are likely going to increase in many urban coastal areas. Some kind of innovative methodologies and practices should be needed to get more flood resilience cities

Optimization of urban mobility measures to achieve win-win strategies

European cities are essential in the development of Europe as they constitute the living environment of more than 60% of the population in the European Union and are drivers of the European economy – just under 85% of the EU’s gross domestic product is produced in urban areas (EC, 2007a). The car has been one of the main factors of development during the 20th century, but it is at the same time the origin of the key problems cities have to face: traffic increase. This has resulted in chronic congestion with many adverse consequences such as air pollution and noise. This loss of environmental quality is one of the reasons for urban sprawl in European cities during recent decades. But this urban sprawl at the same time worsens the environmental conditions. We must return to the dense city, but clean and competitive, and this implies reducing car use yet provides quality transport alternatives sufficient to recover and maintain the competitiveness of cities (EC, 2007a). Consequently, European cities need to establish an urban transport strategy which helps reduce their environmental problems –mainly emissions and noise – but without decreasing their trip attraction. This aspect is very important because a loss of trip attraction would result in an increase of people moving to more disperse areas, contributing towards worsening the current situation. This thesis is an attempt to contribute solutions to this problem in two ways: 1) The first is to analyze the complementarity and possible synergies of several urban transport measures aimed at improving a modal split to a more sustainable means of transport. This analysis will focus on the three aspects already mentioned: emissions, noise and attractiveness or competitiveness. 2) Once possible synergies and complementarities have been analyzed, the second objective is to propose the best combination of these measures, in terms of level of implementation, to achieve the maximum benefit with respect to the three aspects previously established: emissions, noise and attractiveness or competitiveness. Therefore, within the wide range of measures enhancing sustainable urban transport, three of them have been be selected in this thesis to establish a methodology for achieving these objectives. The analysis will be based on the region of Madrid, which is also the case study selected for this research. Las ciudades europeas son piezas fundamentales para el desarrollo europeo, ya que son el lugar de residencia de más del 60% de la población de la unión europea así como los motores de su economía – casi el 85% del PIB europeo se produce en áreas urbanas (EC, 2007a). El coche ha sido uno de los principales motores de desarrollo de las ciudades durante el siglo XX, pero se ha terminado por convertir a su vez en uno de los principales problemas con los que tiene que lidiar las ciudades: el aumento del tráfico. Esto ha derivado en unos niveles crónicos de congestión, con multitud de efectos adversos, entre los que cabe destacar la contaminación del aire y el ruido. Esta pérdida de calidad ambiental es una de las razones que ha propiciado la dispersión urbana que han experimentado las ciudades europeas en las últimas décadas. Pero esta dispersión urbana a su vez contribuye a empeorar las condiciones ambientales de las ciudades. Debemos retornar a la ciudad densa, pero limpia y competitiva, y esto implica reducir el uso del coche, pero proporcionando alternativas de transporte que permitan recuperar y mantener la competitividad de las ciudades (EC, 2007a). Por lo tanto, las ciudades europeas necesitan encontrar una estrategia de transporte urbano que ayude a reducir sus problemas medio ambientales – principalmente ruido y emisiones – pero sin hacerlas perder atractividad o competitividad. Este aspecto tiene gran importancia porque una pérdida de la misma se traduciría en un aumento de dispersión de la población hacia áreas periféricas, contribuyendo a empeorar la situación actual. Esta tesis contribuye a solucionar este problema de dos maneras: 1) La primera, analizando la complementariedad y posibles sinergias de diferentes medidas de transporte urbano orientadas a promover un reparto modal hacia modos más sostenibles. Este análisis se centrará en los tres aspectos anteriormente citados: emisiones, ruido y atractividad o competitividad. 2) Una vez las posibles sinergias y complementariedades se han analizado, el segundo objetivo es proponer la mejor combinación de estas medidas – en términos de grado de aplicación - para lograr el máximo beneficio en lo que respecta a los tres objetivos previamente establecidos. Para ello, en esta tesis se han seleccionado una serie de medidas que permitan establecer una metodología para alcanzar estos objetivos previamente definidos. El análisis se centra en la ciudad de Madrid y su área metropolitana, la cual se ha escogido como caso de estudio para realizar esta investigación.

Rebalancing urban mobility: a tale of four cities

The key of mobility in urban planning is not in dispute. Integrated strategies that take into account the interrelations among land use, transport supply and demand and the different transportation modes are more necessary than ever. In Europe, regulatory tools such as local mobility plans or traffic plans have been enforced for a long time, evolving into so-called sustainable urban transport plans (SUTP) ? that is, plans thatmerge urban planning,mobility governance, social awareness and environmental safeguards to develop a vision based on sustainability and equity. Indeed, SUTP are aimed at solving typical problems in current land use, such as urban sprawl, which make clear the need for a paradigm shift from transport (or mobility) planning to land use (or city) planning, thereby producing urban mobility plans that are fully aligned with integrated urban development plans. This paper describes how SUTP are articulated across Europe according to four case studies: Peterborough (UK), Chambe¿ry (France), Ferrara (Italy) and Pinto (Spain), to highlight variations and commonalities, both among the four national legal frameworks and the actual planning processes at the local level. Objectives, measures and indicators used in the monitoring and evaluation phases have been analysed and the results assessed. The main conclusion of the paper is that, as seen in these real-life examples, the lack of integration between spatial planning and transport strategies results in the unsustainability of urban areas and, therefore, in a significant loss of competitiveness.

Implementation and management of private traffic limitation in urban areas: experiences and methodologies.

This paper shows the results of a research aimed to formulate a general model for supporting the implementation and management of an urban road pricing scheme. After a preliminary work, to define the state of the art in the field of sustainable urban mobility strategies, the problem has been theoretically set up in terms of transport economy, introducing the external costs’ concept duly translated into the principle of pricing for the use of public infrastructures. The research is based on the definition of a set of direct and indirect indicators to qualify the urban areas by land use, mobility, environmental and economic conditions. These indicators have been calculated for a selected set of typical urban areas in Europe on the basis of the results of a survey carried out by means of a specific questionnaire. Once identified the most typical and interesting applications of the road pricing concept in cities such as London (Congestion Charging), Milan (Ecopass), Stockholm (Congestion Tax) and Rome (ZTL), a large benchmarking exercise and the cross analysis of direct and indirect indicators, has allowed to define a simple general model, guidelines and key requirements for the implementation of a pricing scheme based traffic restriction in a generic urban area. The model has been finally applied to the design of a road pricing scheme for a particular area in Madrid, and to the quantification of the expected results of its implementation from a land use, mobility, environmental and economic perspective.

Assessing urban mobility through participatory scenario building and combined utility-regret assessment

La planificación de la movilidad sostenible urbana es una tarea compleja que implica un alto grado de incertidumbre debido al horizonte de planificación a largo plazo, la amplia gama de paquetes de políticas posibles, la necesidad de una aplicación efectiva y eficiente, la gran escala geográfica, la necesidad de considerar objetivos económicos, sociales y ambientales, y la respuesta del viajero a los diferentes cursos de acción y su aceptabilidad política (Shiftan et al., 2003). Además, con las tendencias inevitables en motorización y urbanización, la demanda de terrenos y recursos de movilidad en las ciudades está aumentando dramáticamente. Como consecuencia de ello, los problemas de congestión de tráfico, deterioro ambiental, contaminación del aire, consumo de energía, desigualdades en la comunidad, etc. se hacen más y más críticos para la sociedad. Esta situación no es estable a largo plazo. Para enfrentarse a estos desafíos y conseguir un desarrollo sostenible, es necesario considerar una estrategia de planificación urbana a largo plazo, que aborde las necesarias implicaciones potencialmente importantes. Esta tesis contribuye a las herramientas de evaluación a largo plazo de la movilidad urbana estableciendo una metodología innovadora para el análisis y optimización de dos tipos de medidas de gestión de la demanda del transporte (TDM). La metodología nueva realizado se basa en la flexibilización de la toma de decisiones basadas en utilidad, integrando diversos mecanismos de decisión contrariedad‐anticipada y combinados utilidad‐contrariedad en un marco integral de planificación del transporte. La metodología propuesta incluye dos aspectos principales: 1) La construcción de escenarios con una o varias medidas TDM usando el método de encuesta que incorpora la teoría “regret”. La construcción de escenarios para este trabajo se hace para considerar específicamente la implementación de cada medida TDM en el marco temporal y marco espacial. Al final, se construyen 13 escenarios TDM en términos del más deseable, el más posible y el de menor grado de “regret” como resultado de una encuesta en dos rondas a expertos en el tema. 2) A continuación se procede al desarrollo de un marco de evaluación estratégica, basado en un Análisis Multicriterio de Toma de Decisiones (Multicriteria Decision Analysis, MCDA) y en un modelo “regret”. Este marco de evaluación se utiliza para comparar la contribución de los distintos escenarios TDM a la movilidad sostenible y para determinar el mejor escenario utilizando no sólo el valor objetivo de utilidad objetivo obtenido en el análisis orientado a utilidad MCDA, sino también el valor de “regret” que se calcula por medio del modelo “regret” MCDA. La función objetivo del MCDA se integra en un modelo de interacción de uso del suelo y transporte que se usa para optimizar y evaluar los impactos a largo plazo de los escenarios TDM previamente construidos. Un modelo de “regret”, llamado “referencedependent regret model (RDRM)” (modelo de contrariedad dependiente de referencias), se ha adaptado para analizar la contribución de cada escenario TDM desde un punto de vista subjetivo. La validación de la metodología se realiza mediante su aplicación a un caso de estudio en la provincia de Madrid. La metodología propuesta define pues un procedimiento técnico detallado para la evaluación de los impactos estratégicos de la aplicación de medidas de gestión de la demanda en el transporte, que se considera que constituye una herramienta de planificación útil, transparente y flexible, tanto para los planificadores como para los responsables de la gestión del transporte. Planning sustainable urban mobility is a complex task involving a high degree of uncertainty due to the long‐term planning horizon, the wide spectrum of potential policy packages, the need for effective and efficient implementation, the large geographical scale, the necessity to consider economic, social, and environmental goals, and the traveller’s response to the various action courses and their political acceptability (Shiftan et al., 2003). Moreover, with the inevitable trends on motorisation and urbanisation, the demand for land and mobility in cities is growing dramatically. Consequently, the problems of traffic congestion, environmental deterioration, air pollution, energy consumption, and community inequity etc., are becoming more and more critical for the society (EU, 2011). Certainly, this course is not sustainable in the long term. To address this challenge and achieve sustainable development, a long‐term perspective strategic urban plan, with its potentially important implications, should be established. This thesis contributes on assessing long‐term urban mobility by establishing an innovative methodology for optimizing and evaluating two types of transport demand management measures (TDM). The new methodology aims at relaxing the utility‐based decision‐making assumption by embedding anticipated‐regret and combined utilityregret decision mechanisms in an integrated transport planning framework. The proposed methodology includes two major aspects: 1) Construction of policy scenarios within a single measure or combined TDM policy‐packages using the survey method incorporating the regret theory. The purpose of building the TDM scenarios in this work is to address the specific implementation in terms of time frame and geographic scale for each TDM measure. Finally, 13 TDM scenarios are built in terms of the most desirable, the most expected and the least regret choice by means of the two‐round Delphi based survey. 2) Development of the combined utility‐regret analysis framework based on multicriteria decision analysis (MCDA). This assessment framework is used to compare the contribution of the TDM scenario towards sustainable mobility and to determine the best scenario considering not only the objective utility value obtained from the utilitybased MCDA, but also a regret value that is calculated via a regret‐based MCDA. The objective function of the utility‐based MCDA is integrated in a land use and transport interaction model and is used for optimizing and assessing the long term impacts of the constructed TDM scenarios. A regret based model, called referente dependent regret model (RDRM) is adapted to analyse the contribution of each TDM scenario in terms of a subjective point of view. The suggested methodology is implemented and validated in the case of Madrid. It defines a comprehensive technical procedure for assessing strategic effects of transport demand management measures, which can be useful, transparent and flexible planning tool both for planners and decision‐makers.

Evaluación del dispositivo Raspberry Pi como elemento de despliegue de servicios en el marco de las Smart Grids

La tendencia actual de las redes de telecomunicaciones conduce a pensar en un futuro basado en el concepto emergente de las Smart Cities¸ que tienen como objetivo el desarrollo urbano basado en un modelo de sostenibilidad que responda a las necesidades crecientes de las ciudades. Dentro de las Smart Cities podemos incluir el concepto de Smart Grid, el cual está referido a sistemas de administración y producción de energía eficientes, que permitan un sistema energético sostenible, y que den cabida a las fuentes de energía renovables. Sistemas de este tipo se muestran a los usuarios como un conjunto de servicios con los que interactuar sin ser tan sólo un mero cliente, sino un agente más del entorno energético. Por otro lado, los sistemas de software distribuidos son cada vez más comunes en una infraestructura de telecomunicaciones cada vez más extensa y con más capacidades. Dentro de este ámbito tecnológico, las arquitecturas orientadas a servicios han crecido exponencialmente sobre todo en el sector empresarial. Con sistemas basados en estas arquitecturas, se pueden ofrecer a empresas y usuarios sistemas software basados en el concepto de servicio. Con la progresión del hardware actual, la miniaturización de los equipos es cada vez mayor, sin renunciar por ello a la potencia que podemos encontrar en sistemas de mayor tamaño. Un ejemplo es el dispositivo Raspberry Pi, que contiene un ordenador plenamente funcional contenido en el tamaño de una cajetilla de tabaco, y con un coste muy reducido. En este proyecto se pretenden aunar los tres conceptos expuestos. De esta forma, se busca utilizar el dispositivo Raspberry Pi como elemento de despliegue integrado en una arquitectura de Smart Grid orientada a servicios. En los trabajos realizados se ha utilizado la propuesta definida por el proyecto de I+D europeo e-GOTHAM, con cuya infraestructura se ha tenido ocasión de realizar diferentes pruebas de las descritas en esta memoria. Aunque esta arquitectura está orientada a la creación de una Smart Grid, lo experimentado en este PFG podría encajar en otro tipo de aplicaciones. Dentro del estudio sobre las soluciones software actuales, se ha trabajado en la evaluación de la posibilidad de instalar un Enterprise Service Bus en el Raspberry Pi y en la optimización de la citada instalación. Una vez conseguida una instalación operativa, se ha desarrollado un controlador de un dispositivo físico (sensor/actuador), denominado Dispositivo Lógico, a modo de prueba de la viabilidad del uso del Raspberry Pi para actuar como elemento en el que instalar aplicaciones en entornos de Smart Grid o Smart Home. El éxito logrado con esta experimentación refuerza la idea de considerar al Raspberry Pi, como un importante elemento a tener en cuenta para el despliegue de servicios de Smart Cities o incluso en otros ámbitos tecnológicos. ABSTRACT. The current trend of telecommunication networks lead to think in a future based on the emerging concept of Smart Cities, whose objective is to ensure the urban development based on a sustainable model to respond the new necessities of the cities. Within the Smart cites we can include the concept of Smart Grid, which is based on management systems and efficient energy production, allowing a sustainable energy producing system, and that includes renewable energy sources. Systems of this type are shown to users as a set of services that allow users to interact with the system not only as a single customer, but also as other energy environment agent. Furthermore, distributed software systems are increasingly common in a telecommunications infrastructure more extensive and with more capabilities. Within this area of technology, service-oriented architectures have grown exponentially especially in the business sector. With systems based on these architectures, can be offered to businesses and users software systems based on the concept of service. With the progression of the actual hardware, the miniaturization of computers is increasing, without sacrificing the power of larger systems. An example is the Raspberry Pi, which contains a fully functional computer contained in the size of a pack of cigarettes, and with a very low cost. This PFG (Proyecto Fin de Grado) tries to combine the three concepts presented. Thus, it is intended to use the Raspberry Pi device as a deployment element integrated into a service oriented Smart Grid architecture. In this PFG, the one proposed in the European R&D e-GOTHAM project has been observed. In addition several tests described herein have been carried out using the infrastructure of that project. Although this architecture is oriented to the creation of a Smart Grid, the experiences reported in this document could fit into other applications. Within the study on current software solutions, it have been working on assessing the possibility of installing an Enterprise Service Bus in the Raspberry Pi and optimizing that facility. Having achieved an operating installation, it has been developed a driver for a physical device (sensor / actuator), called logical device, for testing the feasibility of using the Raspberry Pi to act as an element in which to install applications in Smart Grid and Smart Home Environments. The success of this experiment reinforces the idea of considering the Raspberry Pi as an important element to take into account in the deployment of Smart Cities services or even in other technological fields.

The role of the urban support in the regeneration of vulnerable neighbourhoods

The processes of social and urban segregation have got worse during the last decades. Several studies have deepened into the analysis of the causes and consequences of these processes and have tried to define solutions that beyond eradicating some specific problems, were aimed at the consolidation of sustainable urban environments. This paper presents an approach to the problem of urban inequality based on the concept of urban vulnerability as something that goes beyond the social and economic problems. In exclusion processes it is very important to consider the urban context and the physical and structural conditions not only in each neighborhood but also in the city as a whole. The paper seeks to pose a reflection on the urban support, which is understood in all its complexity and thought to be a key to ensure access and the right to the city of the citizens most in need.

Los residuos de envases y embalajes en edificación residencial. Patrones de generación y estrategias de mejora de su gestión

Uno de los retos a los que se enfrenta la humanidad es la demanda de una sociedad con casi cero residuos: la búsqueda de una economía más eficiente en el uso de los recursos teniendo en cuenta el cambio climático y un abastecimiento sostenible de materias primas que permitan satisfacer las necesidades de una población mundial cada vez mayor, dentro de los límites sostenibles de los recursos naturales del planeta. Abordar este desafío implica la recuperación y reciclaje de materiales para reducir consumos de materias primas y, para ello, debe promoverse la innovación en la prevención y gestión de residuos, como estrategia hacia un desarrollo urbano sostenible. Los envases y embalajes forman parte de la cultura actual, relacionándose con el grado de desarrollo de países y regiones; el sector de la construcción no es ajeno a la problemática y genera un importante volumen de embalajes en las obras que no se gestionan de forma adecuada. El modelo de gestión de Residuos de Construcción Demolición (RCD) actual es poco eficaz, ya que los vertederos siguen recibiendo grandes cantidades de residuos valorizables. La normativa ha conseguido minimizar las prácticas ilegales, pero se comprueba que la gestión actual de los RCD en obra deja en manos de las plantas de tratamiento la misión de separar los residuos según su naturaleza y los datos aportados por las distintas plantas no permiten afirmar el grado de alcance de dicho objetivo, ni el destino de los mismos. Los envases y embalajes son un tipo de residuos que por su naturaleza suponen una fuente de recursos valorizables y por ello están presentes en directivas y leyes, dirigidas fundamentalmente al sector de la alimentación. En el ámbito de la construcción, hasta la fecha, no se habían tratado de forma específica, motivo que justifica este trabajo. Esta Tesis Doctoral tiene como objetivo principal mejorar la gestión de residuos de embalajes procedentes de materiales de construcción. Para ello se estudia un importante conjunto de obras de edificación residencial colectiva de 1173 viviendas, análisis que llevará a conocer los patrones de producción de los Residuos de Envases y Embalajes en Construcción (REEC) e identificar los productos o materiales responsables de su generación. La monitorización realizada, permitirá diseñar estrategias específicas que minimicen la generación de estos residuos y optimicen su valorización. Se ha podido comprobar que el tratamiento particularizado de los REEC puede mejorar los resultados de la gestión del conjunto de RCD, debido a que, al no mezclarse, se elimina un importante agente contaminador de los residuos inertes. Las obras analizadas alcanzan un nivel de segregación in situ muy bajo, y los capítulos de cerramientos e instalaciones suman más del 50% del global de REEC. Particularizando en cada tipo de material, el cartón predomina en los trabajos de electricidad, el plástico en las particiones y la madera en fachadas. Se evalúa la opción del eco-­‐rediseño para uno de los embalajes predominantes, y se identifican estrategias para minimizar su impacto. Se comprueba que el ahorro en la gestión de RCD en caso de impulsar la segregación in situ no es muy significativo en las obras estudiadas, si bien se demuestra que la viabilidad económica es el factor más importante para motivar a las empresas constructoras. Las Administraciones Públicas deberían incentivar la gestión responsable, estableciendo medidas de control en las plantas de tratamiento e implementando en sus obras medidas de gestión de RCD ejemplares para el mercado. Una adecuada planificación de la obra, y formación específica para el personal son medidas que facilitan la segregación in situ y mejoran los resultados. Los promotores, mediante su relación contractual con el resto de agentes, tienen la capacidad de establecer objetivos de reducción, planificación y gestión sostenible de los REEC. Por último, se propone un sistema de gestión de REEC, integrable dentro del Sistema de Gestión de la empresa constructora, que permite evitar que residuos valorizables tales como los envases y embalajes se envíen a vertedero, guiando al sector hacia un futuro más respetuoso, alineado con el desarrollo sostenible. ABSTRACT One of the challenges humanity faces is the demand of an almost zero waste society: the search for a more efficient economy in the use of resources, taking into account climate change and a sustainable supply of raw materials, that meet the needs of an increasing world population within the sustainable limits of the planet's natural resources. Addressing this challenge involves the recovery and recycling of materials to reduce consumption of raw materials, so innovation must therefore be promoted in the prevention and management of waste, as a strategy towards a sustainable urban development. Packaging is part of our current culture and is related to the degree of development of countries and regions; the construction sector is no stranger to this problem and generates a significant amount of packaging waste in the site works, which nowadays is not managed properly. The current Construction Demolition Waste (CDW) management model is ineffective, since landfills continue to receive large amounts of recoverable waste. The legislation has managed to minimize illegal practices, but it has been observed that the current management of CDW in the analysed works leaves the mission of separating waste according to their nature to the plants, and data provided by the latter does not allow for checking the scope of this objective, nor the destiny of the waste. Packaging is a type of waste which, by its nature, represents a source of recoverable resources and is therefore present in directives and laws, focused primarily on the food industry. It has not been specifically treated to date in the construction field, hence the reason that justifies this work. This Thesis aims to improve the management of packaging waste from construction materials. An important set of residential building works with 1173 dwellings is analysed, which leads to knowledge on the production patterns of packaging waste (PW) in the construction industry, and the identification of the products responsible for its generation. The monitorization also allows for the design of specific strategies which minimise the generation of waste and optimize recovery. It has been found that the individualized treatment of PW can improve the results of the management of the whole CDW since, when not mixed, a major pollutant of inert waste is removed. The analysed works reached a very low segregation level and the façades and building services phases account for more than 50% of the overall PW. Focusing on each type of material, cardboard predominates electricity works, plastic on partitions and wood on façades. Eco-­‐redesign is evaluated for one of the predominant packages, and strategies are identified to minimise their impact are . There is evidence that the savings in the CDW management in case of promoting segregation on site are not very significant at the studied works, although economic feasibility is the most important factor to motivate the construction companies. Public Administrations should encourage responsible management, establishing control measures in treatment plants and implementing CDW management exemplary measures on their work sites for the market. A proper planning of the works and specific training for the personnel are measures that facilitate in situ segregation and improve outcomes. The developers, through their contractual relationship with the other agents, have the ability to set reduction targets, planning and sustainable management of PW. Finally, a management system for PW is proposed, integrated within the Management System of the construction company, which aims to avoid that recoverable waste such as packaging is sent to landfill, leading the industry towards a more environmentally friendly future, aligned with sustainable development.

Formación y determinación del valor del suelo: confrontación y discrepancias entre mecanismos de mercado y regulaciones administrativas

La determinación del valor del suelo implicado en los procesos de urbanización se mueve en una compleja dialéctica en la que algunos fenómenos de naturaleza morfológica como el modelado del espacio social, o el que se deduce de las determinaciones del planeamiento (aprovechamiento especialmente) se enfrentan a instrumentos de regulación que se rigen por normas de carácter administrativo (urbanísticas y expropiatorias, fiscales, financieras-hipotecarias etc.). En ese marco en el que las discrepancias son frecuentes se pretende analizar las posibles actuaciones encaminadas a influir sobre la formación de ese valor en el sentido de limitar las expectativas de aprovechamiento tradicionalmente vinculadas al sistema urbanístico establecido, destacando al respecto la implantación de criterios de sostenibilidad y participación ciudadana, así como que la utilización de normas administrativas de valoración con la finalidad de reducir tales expectativas y tratar de influir sobre el sistema urbanístico en su conjunto, no se considera suficiente para conseguir el logro de tales objetivos. Añadiendo, respecto del conjunto de normas administrativas de determinación del valor del suelo, que si bien las reglas urbanísticas y expropiatorias establecen actualmente reglas objetivas de valoración, a través de la normativa de valoración destinada a entidades financieras, o de carácter fiscal, se introducen criterios subjetivos que tratan de aproximarse al mercado, incluso en el caso del valor catastral, estructuralmente reglado. Esta separación de criterios ha llevado a un enfrentamiento al que ha venido a dar respuesta la reciente sentencia del Tribunal Supremo de 30 de mayo de 2014, que impone los criterios urbanísticos de consideración de situaciones básicas de suelo, frente a los fiscalmente regulados en relación con la normativa catastral en cuanto a la consideración de suelo urbanizable sin desarrollar, que pasa a ser considerado como en situación rural, siendo por tanto aplicables sobre el mismo las reglas de valoración que la normativa catastral establece para esta categoría de suelo (rústico) que no considera, incluso con la posterior modificación, de junio de 2015, incorporada para adaptarse a la mencionada sentencia, expectativas de aprovechamiento. Pero como se ha señalado, la exclusiva utilización de la normativa urbanística de valoración no se considera suficiente para evitar los efectos que sobre el valor de suelo produce la asignación de tales aprovechamientos, por lo que acuerdo con la actual legislación de suelo, deben asimismo potenciarse actuaciones encaminadas a un desarrollo sostenible así como a la participación ciudadana, la transparencia y el control, con la finalidad de lograr un mayor rigor en la utilización del suelo que ha de traducirse en su valoración. ABSTRACT Determining the land value involved in the urbanisation process implies a complex dialectic in which certain morphological natural phenomena like the modelling of social space or that deduced from planning determinations (especially land use) face regulatory instruments governed by administrative norms (urban planning and expropriator, tax, financial-mortgage etc.). In this context where discrepancies are common, the purpose is to analyse the possible actions geared to influence the formation of that value in the sense of limiting land use expectations traditionally linked to the established urban planning system, highlighting the implementation of sustainability criteria and citizen participation, as well as to consider that the administrative standards of evaluation for reducing said expectations, and trying to influence the urban system as a whole, are not considered sufficient for achieving these objectives. We might add, with respect to the set of administrative norms for determining the land value, that while urban and expropriations norms currently provide objective rules of valuation, subjective criteria are introduced trying to approach the market, including the structurally regulated cadastral value through valuation rules aimed at financial or fiscal institutions. This separation of criteria has led to a confrontation to which the recent ruling of the Supreme Court of May 30, 2014 responds. The aforementioned judgement imposes the urban core criteria for basic land use situations against those fiscally regulated in relation to cadastral regulations regarding the consideration of undeveloped building land, which is considered to be in a rural situation, making it subject to the same rules that cadastral valuation norms established for this category of land use (rustic) which do not consider, even with the subsequent amendment of June 2015, introduced to fit that judgment, use expectations. But as noted, the exclusive use of valuation planning regulations is not considered sufficient to avoid the effects on the land value produced by the allocation of said uses, so that according to the current land use legislation, actions aimed at sustainable development as well as citizen participation, transparency and control, shall be enhanced in order to achieve greater rigor in the use of land which should be translated in their valuation.

Arsenic, antimony and selenium in urban soils: potential risks for human health in urban gardening

The benefits of urban agriculture are many and well documented, ranging from health improvement to community betterment, more sustainable urban development and environment protection. On the negative side, urban soils are commonly enriched in toxic trace elements that have accumulated over time through the deposition of atmospheric particles (generated by automotive traffic, heating systems, historical industrial activities and resuspended street dust), and the uncontrolled disposal of domestic, commercial and industrial wastes. This in turn has given rise to concerns about the level of exposure of urban farmers to these elements and the potential health hazards associated with this exposure. Research efforts in this field have started relatively recently and have almost systematically omitted the influence of Sb and Se, and to a lesser extent of As, although all three have proven toxic effects.

PPP in light rail transit systems in Spain

Light rail systems have proliferated in Spain in the last decade, following a tendency that is common not only in other European countries but also in other parts of the world. This paper reviews the benefits of light rail systems, both related to environmental issues and mobility issues. It analyses the evolution of light rail projects in Spain and shows that light rail systems in this country have evolved towards an extensive use of public-private partnerships. The analysis of the Spanish projects, however, does not contribute any conclusive evidence about whether public-private partnerships have been more efficient than publicly owned enterprises in building and operating light rail systems.

Alteración del comportamiento hidráulico natural de la vertiente noreste de la marisma de El Rocío por efectos antrópicos

El geo-dinamismo torrencial es resultado de la incidencia de precipitaciones torrenciales en la cuenca hidrográfica, y se manifiesta por una intensificación del ciclo del agua (con la presencia de mayores volúmenes de escorrentía y la consiguiente aparición de repentinos y elevados caudales de avenida) e intensificación del ciclo de los sedimentos (mayor erosión del suelo, incremento del transporte de sedimentos en los cauces de drenaje y la formación de grades depósitos de sedimentos en el área dominada de la cuenca). Estos procesos naturales se pueden agravar si se realizan en la cuenca actuaciones que alteren sustancialmente su morfología; es el caso del arroyo del Partido, tributario a la marisma de El Rocío en el Parque Nacional de Doñana, cuyo encauzamiento del tramo final sobre su antiguo cono de sedimentación fue el causante de la formación de un nuevo cono de sedimentación sobre la marisma. Pero las intervenciones antrópicas también pueden dirigir el sistema hacia la estabilidad sedimentaria y el tramo final del arroyo del Partido ha experimentado asimismo actuaciones de carácter restaurador. El antiguo cono de sedimentación del arroyo del Partido es un lugar complejo en el que drenan también otros tres cursos que intercambian sus flujos con dicho arroyo durante las avenidas. Esta Memoria analiza cuatro situaciones del paraje objeto de estudio: la primera responde al estado original del lugar en cuestión (situación A); la segunda a la creada tras el encauzamiento del arroyo del Partido en 1981 (situación B); la tercera a la formada pasado un tiempo desde el encauzamiento, cuando el geo-dinamismo del lugar hizo sus efectos sobre el paraje en cuestión (situación C); y la cuarta la generada tras la restauración en el verano de 2006 del régimen hidráulico-sedimentario del arroyo del Partido con la Actuación núm. 3 del Proyecto Doñana 2005. Se han investigado los efectos que la alteración de la morfología del sistema de drenaje del antiguo cono de sedimentación del arroyo del Partido causa en los parámetros hidráulicos que desencadenan el geo-dinamismo torrencial. Para ello se han reproducido las condiciones morfológicas de las cuatro situaciones más representativas ya comentadas que ha experimentado el paraje en los últimos 30 años y que han condicionado el comportamiento de las avenidas torrenciales ocurridas en dicho periodo. En este contexto se ha elaborado un modelo hidrológico con el programa HECHMS a partir de la información disponible y un modelo hidrodinámico en 2D con el programa IBER; con este último se han comparado ocho escenarios característicos derivados de la incidencia de dos avenidas representativas de los eventos torrenciales de la zona sobre las morfologías contempladas. También se ha estudiado la tensión de arrastre de las avenidas dada su incidencia en el terreno sobre el que transitan, analizando de manera separada los efectos en los cuatro cauces de drenaje del antiguo cono de sedimentación y del resto de la superficie del mismo. La investigación realizada ha permitido describir minuciosamente el comportamiento de los drenajes locales del antiguo y complejo cono de sedimentación que bordea el noroeste de la marisma del Parque Nacional de Doñana, desde la marisma de El Rocío hasta la marisma gallega, lo que redundará en beneficio de la gestión del Parque Nacional de Doñana y de su entorno, y especialmente en la seguridad del perímetro oriental de la aldea de El Rocío. ABSTRACT The torrential geo-dynamism results from the effect of torrential precipitations on the hydrological watershed, and it shows ups with the intensification of the water cycle (with presence of higher volumes of run-off and the consequent appearance of sudden and high food flows) and intensification of the sediment cycle (higher soil erosion, increase of sediment transport in the drainage courses and the formation of big sediment deposits in the area downstream the watershed). These natural processes can worsen if actions that change the morphology of the watershed are carried out. It is the case of the Partido stream, tributary of the marsh of El Rocío in the Doñana National Park, whose channelization of the final stretch over its old alluvial fan was the cause of the formation of a new alluvial fan over the marsh. But human actions can also go toward the sediment stabilization, and the final stretch of the Partido stream has experienced restoration actions as well. The old alluvial fan of the Partido stream is a complex terrain where also other three courses exchange their flows during floods. This document analyses four situations of the area studied: the first corresponds to the original state of the place (situation A); the second is the state created after the channel of the Partido stream was built in 1981 (situation B); the third is the state formed after some time passed and the geo-dynamism caused effect in the channelization (situation C); and the forth situation is the one created after the restoration in summer of 2006 of the hydraulic-sedimentary regime of the Partido stream with de Action number 3 of the Doñana 2005 Project. It has been researched the effects that the alteration of the morphology of the drainage system of the old alluvial fan of the Partido stream causes to the hydraulic parameters that trigger the torrential geo-dynamism. For that, the morphologic conditions of the four more representative situations were reproduced. Those situations experienced in the area in the last 30 years have conditioned the behaviour of torrential floods in that period. In this context, a hydrologic model with HEC-HMS and a 2D hydro-dynamic model with IBER have been set up. With IBER, eight scenes have been compared resulting from the impact of two representative floods from torrential events in the region against the morphologies considered. Also, the shear stress of the floods on the terrain has been studied, analysing separately the effect in the four drainage courses of the old alluvial fan and in the rest of its surfaces. The research carried out has allowed describing in minute detail the behavior of the local drainages of the old and complex alluvial fan that border the northwest part of the marsh of Doñana National Park, from the marsh of El Rocío to the gallega marsh. This will result in benefit for the management of Doñana National Park and its surroundings, and especially for the safety of the eastern limit of El Rocío village.

Repair works at Saint Claire Convent in Chinchón (Madrid, Spain)

The Chinchón Saint Claire Convent is a Count Foundation of 1653. Some repair works were made around 1965, but some important cracks were remained. This paper describes the soil study made to know, its properties, the reason of these movements and its consequences to the convent and the repair works done. A high swelling phenomenon has been detected. The convent is on a high plasticity clayey soil with soil sandy insertions. The soil water has a high content of sulphates. In addition, some sewer system piping was broken around the convent and frequently flooded the convent crypt. A micropiles underpinning was made and the water leaked has lead to the sewer system to avoid the crypt flooding, also a drainage system has been made and the ground around the church has been paved.