Estudio de la rotura en barras de acero : aspectos experimentales y numéricos

El acero es, junto con el hormigón, el material más ampliamente empleado en la construcción de obra civil y de edificación. Además de su elevada resistencia, su carácter dúctil resulta un aspecto de particular interés desde el punto de vista de la seguridad estructural, ya que permite redistribuir esfuerzos a elementos adyacentes y, por tanto, almacenar una mayor energía antes del colapso final de la estructura. No obstante, a pesar de su extendida utilización, todavía existen aspectos relacionados con su comportamiento en rotura que necesitan una mayor clarificación y que permitirían un mejor aprovechamiento de sus propiedades. Cuando un elemento de acero es ensayado a tracción y alcanza la carga máxima, sufre la aparición de un cuello de estricción que plantea dificultades para conocer el comportamiento del material desde dicho instante hasta la rotura. La norma ISO 6892-1, que define el método a emplear en un ensayo de tracción con materiales metálicos, establece procedimientos para determinar los parámetros relacionados con este tramo último de la curva F − E. No obstante, la definición de dichos parámetros resulta controvertida, ya que éstos presentan una baja reproducibilidad y una baja repetibilidad que resultan difíciles de explicar. En esta Tesis se busca profundizar en el conocimiento del último tramo de la curva F − E de los aceros de construcción. Para ello se ha realizado una amplia campaña experimental sobre dos aceros representativos en el campo de la construcción civil: el alambrón de partida empleado en la fabricación de alambres de pretensado y un acero empleado como refuerzo en hormigón armado. Los dos materiales analizados presentan formas de rotura diferentes: mientras el primero de ellos presenta una superficie de rotura plana con una región oscura claramente apreciable en su interior, el segundo rompe según la clásica superficie en forma de copa y cono. La rotura en forma de copa y cono ha sido ampliamente estudiada en el pasado y existen modelos de rotura que han logrado reproducirla con éxito, en especial el modelo de Gurson- Tvergaard-Needleman (GTN). En cuanto a la rotura exhibida por el primer material, en principio nada impide abordar su reproducción numérica con un modelo GTN, sin embargo, las diferencias observadas entre ambos materiales en los ensayos experimentales permiten pensar en otro criterio de rotura. En la presente Tesis se realiza una amplia campaña experimental con probetas cilíndricas fabricadas con dos aceros representativos de los empleados en construcción con comportamientos en rotura diferentes. Por un lado se analiza el alambrón de partida empleado en la fabricación de alambres de pretensado, cuyo frente de rotura es plano y perpendicular a la dirección de aplicación de la carga con una región oscura en su interior. Por otro lado, se estudian barras de acero empleadas como armadura pasiva tipo B 500 SD, cuyo frente de rotura presenta la clásica superficie en forma de copa y cono. Estos trabajos experimentales han permitido distinguir dos comportamientos en rotura claramente diferenciados entre ambos materiales y, en el caso del primer material, se ha identificado un comportamiento asemejable al exhibido por materiales frágiles. En este trabajo se plantea la hipótesis de que el primer material, cuya rotura provoca un frente de rotura plano y perpendicular a la dirección de aplicación de la carga, rompe de manera cuasifrágil como consecuencia de un proceso de decohesión, de manera que la región oscura que se observa en el centro del frente de rotura se asemeja a una entalla circular perpendicular a la dirección de aplicación de la carga. Para la reproducción numérica de la rotura exhibida por el primer material, se plantea un criterio de rotura basado en un modelo cohesivo que, como aspecto novedoso, se hace depender de la triaxialidad de tensiones, parámetro determinante en el fallo de este tipo de materiales. Este tipo de modelos presenta varias ventajas respecto a los modelos GTN habitualmente empleados. Mientras los modelos GTN precisan de numerosos parámetros para su calibración, los modelos cohesivos precisan fundamentalmente de dos parámetros para definir su curva de ablandamiento: la tensión de decohesión ft y la energía de fractura GF . Además, los parámetros de los modelos GTN no son medibles de manera experimental, mientras que GF sí lo es. En cuanto a ft, aunque no existe un método para su determinación experimental, sí resulta un parámetro más fácilmente interpretable que los empleados por los modelos GTN, que utilizan valores como el porcentaje de huecos presentes en el material para iniciar el fenómeno de coalescencia o el porcentaje de poros que provoca una pérdida total de la capacidad resistente. Para implementar este criterio de rotura se ha desarrollado un elemento de intercara cohesivo dependiente de la triaxialidad de tensiones. Se han reproducido con éxito los ensayos de tracción llevados a cabo en la campaña experimental empleando dicho elemento de intercara. Además, en estos modelos la rotura se produce fenomenológicamente de la misma manera observada en los ensayos experimentales: produciéndose una decohesión circular en torno al eje de la probeta. En definitiva, los trabajos desarrollados en esta Tesis, tanto experimentales como numéricos, contribuyen a clarificar el comportamiento de los aceros de construcción en el último tramo de la curva F − E y los mecanismos desencadenantes de la rotura final del material, aspecto que puede contribuir a un mejor aprovechamiento de las propiedades de estos aceros en el futuro y a mejorar la seguridad de las estructuras construidas con ellos. Steel is, together with concrete, the most widely used material in civil engineering works. Not only its high strength, but also its ductility is of special interest from the point of view of the structural safety, since it enables stress distribution with adjacent elements and, therefore, more energy can be stored before reaching the structural failure. However, despite of being extensively used, there are still some aspects related to its fracture behaviour that need to be clarified and that will allow for a better use of its properties. When a steel item is tested under tension and reaches the maximum load point, necking process begins, which makes difficult to define the material behaviour from that moment onward. The ISO standard 6892-1, which defines the tensile testing method for metallic materials, describes the procedures to obtain some parameters related to this last section of the F − E curve. Nevertheless, these parameters have proved to be controversial, since they have low reproducibility and repeatibility rates that are difficult to explain. This Thesis tries to deepen the knowledge of the last section of the F − E curve for construction steels. An extensive experimental campaign has been carried out with two representative steels used in civil engineering works: a steel rod used for manufacturing prestressing steel wires, before the cold-drawing process is applied, and steel bars used in reinforced concrete structures. Both materials have different fracture surfaces: while the first of them shows a flat fracture surface, perpendicular to the loading direction with a dark region in the centre of it, the second one shows the classical cup-cone fracture surface. The cup-cone fracture surface has been deeply studied in the past and different numerical models have been able to reproduce it with success, with a special mention to the Gurson-Tvergaard-Needleman model (GTN). Regarding the failure surface shown by the first material, in principle it can be numerically reproduced by a GTN model, but the differences observed between both materials in the experimental campaign suggest thinking of a different failure criterium. In the present Thesis, an extensive experimental campaign has been carried out using cylindrical specimens made of two representative construction steels with different fracture behaviours. On one hand, the initial eutectoid steel rod used for manufacturing prestressing steel wires is analysed, which presents a flat fracture surface, perpendicular to the loading direction, and with a dark region in the centre of it. On the other hand, B 500 SD steel bars, typically used in reinforced concrete structures and with the typical cup-cone fracture surface, are studied. These experimental works have allowed distinguishing two clearly different fracture behaviours between both materials and, in the case of the first one, a fragile-like behaviour has been identified. For the first material, which shows a flat fracture surface perpendicular to the loading direction, the following hypothesis is proposed in this study: a quasi-brittle fracture is developed as a consequence of a decohesion process, with the dark region acting as a circular crack perpendicular to the loading direction. To reproduce numerically the fracture behaviour shown by the first material, a failure criterium based on a cohesive model is proposed in this Thesis. As an innovative contribution, this failure criterium depends on the stress triaxiality state of the material, which is a key parameter when studying fracture in this kind of materials. This type of models have some advantages when compared to the widely used GTN models. While GTN models need a high number of parameters to be defined, cohesive models need basically two parameters to define the softening curve: the decohesion stress ft and the fracture energy GF . In addition to this, GTN models parameters cannot be measured experimentally, while GF is indeed. Regarding ft, although no experimental procedure is defined for its obtention, it has an easier interpretation than the parameters used by the GTN models like, for instance, the void volume needed for the coalescence process to start or the void volume that leads to a total loss of the bearing capacity. In order to implement this failure criterium, a triaxiality-dependent cohesive interface element has been developed. The experimental results obtained in the experimental campaign have been successfully reproduced by using this interface element. Furthermore, in these models the failure mechanism is developed in the same way as observed experimentally: with a circular decohesive process taking place around the longitudinal axis of the specimen. In summary, the works developed in this Thesis, both experimental and numerical, contribute to clarify the behaviour of construction steels in the last section of the F − E curve and the mechanisms responsible for the eventual material failure, an aspect that can lead to a better use of the properties of these steels in the future and a safety improvement in the structures built with them.

Seguridad estructural para construcciones en zonas inundables : criterio de diseño : soluciones de minoración del riesgo de fallo

La gestión de riesgos debe ser entendida como una determinación de vínculos entre lo que se asume como vulnerabilidad, y la forma en la que se determinarían o estimarían la probabilidad en la concurrencia de un determinado hecho, partiendo de la idea de la concurrencia de un fenómeno y las acciones necesarias que deberán llevarse a cabo. El tema de vulnerabilidad y riesgo, cada día toma más importancia a nivel mundial, a medida que pasa el tiempo es más notoria la vulnerabilidad de ciertas poblaciones ante la presencia de determinados peligros naturales como son: inundaciones, desbordes de ríos, deslizamientos de tierra y movimientos sísmicos. La vulnerabilidad aumenta, a medida que crece la deforestación. La construcción en lugares de alto riesgo, como por ejemplo, viviendas a orillas de los ríos, está condicionada por la localización y las condiciones de uso del suelo, infraestructura, construcciones, viviendas, distribución y densidad de población, capacidad de organización, etc. Es ahora donde la gestión de riesgos, juega un papel muy importante en la sociedad moderna, siendo esta cada vez más exigente con los resultados y calidad de productos y servicios, además de cumplir también, con la responsabilidad jurídica que trae la concepción, diseño y construcción de proyectos en zonas inundables. El presente trabajo de investigación, se centra en identificar los riesgos, aplicando soluciones estructurales y recomendaciones resilientes para edificaciones que se encuentren emplazadas en zonas inundables. Disminuyendo así el riesgo de fallo estructural y el número de víctimas considerablemente. Concluyendo con un Catálogo de Riesgos y Soluciones para edificaciones en zonas inundables. Risk management should be understood as a determination of links between what is assumed to be vulnerable , and how that would be determined or would estimate the probability in the occurrence of a certain event, based on the idea of the occurrence of a phenomenon and necessary actions to be carried out . The issue of vulnerability and risk, every day takes more importance globally, as time passes is more notorious vulnerability of certain populations in the presence of certain natural hazards such as floods, swollen rivers, landslides and earthquakes. Vulnerability increases as it grows deforestation. The construction in high-risk locations, such as homes on the banks of rivers, is conditioned by the location and conditions of land use, infrastructure, construction, housing, distribution and population density, organizational skills, etc. Now where risk management plays a very important role in modern society, is being increasingly demanding with the results and quality of products and services, and also comply with the legal responsibility that brings the conception, design and construction projects in flood zones. This research focuses on identifying risks, implementing structural solutions and resilients’ recommendations for buildings that are emplaced in flood zones. Thus decreasing the risk of structural failure and the number of victims significantly. Concluding with a Catalogue of Risks and Solutions for buildings in flood zones.

Investigación sobre las causas que pudieron originar el hundimiento de la cubierta del tercer depósito del Canal de Isabel II en 1905

En la presente investigación se analiza la causa del hundimiento del cuarto compartimento del Tercer Depósito del Canal de Isabel II el 8 de abril de 1905, uno de los más graves de la historia de la construcción en España: fallecieron 30 personas y quedaron heridas otras 60. El Proyecto y Construcción de esta estructura era de D. José Eugenio Ribera, una de las grandes figuras de la ingeniería civil en nuestro país, cuya carrera pudo haber quedado truncada como consecuencia del siniestro. Dado el tiempo transcurrido desde la ocurrencia de este accidente, la investigación ha partido de la recopilación de la información relativa al Proyecto y a la propia construcción de la estructura, para revisar a continuación la información disponible sobre el hundimiento. De la construcción de la cubierta es interesante destacar la atrevida configuración estructural, cubriéndose una inmensa superficie de 74.000 m2 mediante una sucesión de bóvedas de hormigón armado de tan sólo 5 cm de espesor y un rebajamiento de 1/10 para salvar una luz de 6 m, que apoyaban en pórticos del mismo material, con pilares también muy esbeltos: 0,25 m de lado para 8 m de altura. Y todo ello en una época en la que la tecnología y conocimiento de las estructuras con este "nuevo" material se basaban en buena medida en el desarrollo de patentes. En cuanto a la información sobre el hundimiento, llama la atención en primer lugar la relevancia de los técnicos, peritos y letrados que intervinieron en el juicio y en el procedimiento administrativo posterior, poniéndose de manifiesto la trascendencia que el accidente tuvo en su momento y que, sin embargo, no ha trascendido hasta nuestros días. Ejemplo de ello es el papel de Echegaray -primera figura intelectual de la época- como perito en la defensa de Ribera, de D. Melquiades Álvarez -futuro presidente del Congreso- como abogado defensor, el General Marvá -uno de los máximos exponentes del papel de los ingenieros militares en la introducción del hormigón armado en nuestro país-, que presidiría la Comisión encargada del peritaje por parte del juzgado, o las opiniones de reconocidas personalidades internacionales del "nuevo" material como el Dr. von Emperger o Hennebique. Pero lo más relevante de dicha información es la falta de uniformidad sobre lo que pudo ocasionar el hundimiento: fallos en los materiales, durante la construcción, defectos en el diseño de la estructura, la realización de unas pruebas de carga cuando se concluyó ésta, etc. Pero la que durante el juicio y en los Informes posteriores se impuso como causa del fallo de la estructura fue su dilatación como consecuencia de las altas temperaturas que se produjeron aquella primavera. Y ello a pesar de que el hundimiento ocurrió a las 7 de la mañana... Con base en esta información se ha analizado el comportamiento estructural de la cubierta, permitiendo evaluar el papel que diversos factores pudieron tener en el inicio del hundimiento y en su extensión a toda la superficie construida, concluyéndose así cuáles fueron las causas del siniestro. De los resultados obtenidos se presta especial atención a las enseñanzas que se desprenden de la ocurrencia del hundimiento, enfatizándose en la relevancia de la historia -y en particular de los casos históricos de error- para la formación continua que debe existir en la Ingeniería. En el caso del hundimiento del Tercer Depósito algunas de estas "enseñanzas" son de plena actualidad, tales como la importancia de los detalles constructivos en la "robustez" de la estructuras, el diseño de estructuras "integrales" o la vigilancia del proceso constructivo. Por último, la investigación ha servido para recuperar, una vez más, la figura de D. José Eugenio Ribera, cuyo papel en la introducción del hormigón armado en España fue decisivo. En la obra del Tercer Depósito se arriesgó demasiado, y provocó un desastre que aceleró la transición hacia una nueva etapa en el hormigón estructural al abrigo de un mayor conocimiento científico y de las primeras normativas. También en esta etapa sería protagonista. This dissertation analyses the cause of the collapse of the 4th compartment of the 3th Reservoir of Canal de Isabel II in Madrid. It happened in 1905, on April 8th, being one of the most disastrous accidents occurred in the history of Spanish construction: 30 people died and 60 were injured. The design and construction supervision were carried out by D. José Eugenio Ribera, one of the main figures in Civil Engineering of our country, whose career could have been destroyed as a result of this accident. Since it occurred more than 100 years ago, the investigation started by compiling information about the structure`s design and construction, followed by reviewing the available information about the accident. With regard to the construction, it is interesting to point out its daring structural configuration. It covered a huge area of 74.000 m2 with a series of reinforced concrete vaults with a thickness of not more than 5 cm, a 6 m span and a rise of 1/10th. In turn, these vaults were supported by frames composed of very slender 0,25 m x 0,25 m columns with a height of 8 m. It is noteworthy that this took place in a time when the technology and knowledge about this "new" material was largely based on patents. In relation to the information about the collapse, its significance is shown by the important experts and lawyers that were involved in the trial and the subsequent administrative procedure. For example, Echegaray -the most important intellectual of that time- defended Ribera, Melquiades Álvarez –the future president of the Congress- was his lawyer, and General Marvá -who represented the important role of the military engineers in the introduction of reinforced concrete in our country-, led the Commission that was put in charge by the judge of the root cause analysis. In addition, the matter caught the interest of renowned foreigners like Dr. von Emperger or Hennebique and their opinions had a great influence. Nonetheless, this structural failure is unknown to most of today’s engineers. However, what is most surprising are the different causes that were claimed to lie at the root of the disaster: material defects, construction flaws, errors in the design, load tests performed after the structure was finished, etc. The final cause that was put forth during the trial and in the following reports was attributed to the dilatation of the roof due to the high temperatures that spring, albeit the collapse occurred at 7 AM... Based on this information the structural behaviour of the roof has been analysed, which allowed identifying the causes that could have provoked the initial failure and those that could have led to the global collapse. Lessons have been learned from these results, which points out the relevance of history -and in particular, of examples gone wrong- for the continuous education that should exist in engineering. In the case of the 3th Reservoir some of these lessons are still relevant during the present time, like the importance of detailing in "robustness", the design of "integral" structures or the due consideration of construction methods. Finally, the investigation has revived, once again, the figure of D. José Eugenio Ribera, whose role in the introduction of reinforced concrete in Spain was crucial. With the construction of the 3th Reservoir he took too much risk and caused a disaster that accelerated the transition to a new era in structural concrete based on greater scientific knowledge and the first codes. In this new period he would also play a major role.

Failure mechanism of reinforced concrete structural walls with and without confinement

This paper presents the results of cyclic loading tests on two large-scale reinforced concrete structural walls that were conducted at Purdue University. One of the walls had confinement reinforcement meeting ACI-318-11 requirements while the other wall did not have any confinement reinforcement. The walls were tested as part of a larger study aimed at indentifying parameters affecting failure modes observed to limit the drift capacity of structural walls in Chile during the Maule Earthquake of 2010. These failure modes include out-of-plane buckling (of the wall rather tan individual reinforcing bars), compression failure, and bond failure. This paper discusses the effects of confinement on failure mode. Distributions of unit strain and curvature obtained with a dense array of non-contact coordinate-tracking targets are also presented.

Degradation in seawater of structural adhesives for hybrid fibre-metal laminated materials

The adhesives used for applications in marine environments are subject to particular chemical conditions, which are mainly characterised by an elevated chlorine ion content and intermittent wetting/drying cycles, among others.These conditions can limit the use of adhesives due to the degradation processes that they experience. In this work, the chemical degradation of two different polymers, polyurethane and vinylester, was studied in natural seawater under immersion for different periods of time.The diffusion coefficients and concentration profiles of water throughout the thickness of the adhesiveswere obtained.Microstructural changes in the polymer due to the action of water were observed by SEM, and the chemical degradation of the polymer was monitored with the Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). The degradation of the mechanical properties of the adhesive was determined by creep tests withMixed Cantilever Beam (MCB) specimens at different temperatures. After 180 days of immersion of the specimens, it was concluded that the J-integral value (depending on the strain) implies a loss of stiffness of 51% and a decrease in the failure load of 59% for the adhesive tested.

Resilience analysis of networked systems-of-systems based on structural and dynamic interdependencies

Critical infrastructures support everyday activities in modern societies, facilitating the exchange of services and quantities of various nature. Their functioning is the result of the integration of diverse technologies, systems and organizations into a complex network of interconnections. Benefits from networking are accompanied by new threats and risks. In particular, because of the increased interdependency, disturbances and failures may propagate and render unstable the whole infrastructure network. This paper presents a methodology of resilience analysis of networked systems of systems. Resilience generalizes the concept of stability of a system around a state of equilibrium, with respect to a disturbance and its ability of preventing, resisting and recovery. The methodology provides a tool for the analysis of off-equilibrium conditions that may occur in a single system and propagate through the network of dependencies. The analysis is conducted in two stages. The first stage of the analysis is qualitative. It identifies the resilience scenarios, i.e. the sequence of events, triggered by an initial disturbance, which include failures and the system response. The second stage is quantitative. The most critical scenarios can be simulated, for the desired parameter settings, in order to check if they are successfully handled, i.e recovered to nominal conditions, or they end into the network failure. The proposed methodology aims at providing an effective support to resilience-informed design.

Effect of fire on the microstructure and mechanical response of structural steels for building construction

The research is an exhaustive study of the microstructure and of the stress-strain curves of structural steel S460N at temperatures typical of a fire. It includes a fractographic study of the fracture suifaces of cylindrical specimens, tensile tested at different fire scenarios, explaining the relationship between the failure micromechanisms and temperature. The paper ends with the comparison between the experimentally found strain-stress curves with that one's proposed by the EUROCODE EC3, resulting that in the case of steel S460N these are on the side ofsafety.

Fracture of concrete structural members subjected to blast

If reinforced concrete structures are to be safe under extreme impulsive loadings such as explosions, a broad understanding of the fracture mechanics of concrete under such events is needed. Most buildings and infrastructures which are likely to be subjected to terrorist attacks are borne by a reinforced concrete (RC) structure. Up to some years ago, the traditional method used to study the ability of RC structures to withstand explosions consisted on a choice between handmade calculations, affordable but inaccurate and unreliable, and full scale experimental tests involving explosions, expensive and not available for many civil institutions. In this context, during the last years numerical simulations have arisen as the most effective method to analyze structures under such events. However, for accurate numerical simulations, reliable constitutive models are needed. Assuming that failure of concrete elements subjected to blast is primarily governed by the tensile behavior, a constitutive model has been built that accounts only for failure under tension while it behaves as elastic without failure under compression. Failure under tension is based on the Cohesive Crack Model. Moreover, the constitutive model has been used to simulate the experimental structural response of reinforced concrete slabs subjected to blast. The results of the numerical simulations with the aforementioned constitutive model show its ability of representing accurately the structural response of the RC elements under study. The simplicity of the model, which does not account for failure under compression, as already mentioned, confirms that the ability of reinforced concrete structures to withstand blast loads is primarily governed by tensile strength.

Effect of fire on the microstructure and mechanical response of structural steels for building construction

The research is an exhaustive study of the microstructure and of the stress-strain curves of structural steel S460N at temperatures typical of a fire. It includes a fractographic study of the fracture suifaces of cylindrical specimens, tensile tested at different fire scenarios, explaining the relationship between the failure micromechanisms and temperature. The paper ends with the comparison between the experimentally found strain-stress curves with that one's proposed by the EUROCODE EC3, resulting that in the case of steel S460N these are on the side ofsafety.

Experimental and numerical study of bond response in structural concrete with corroded steel bars

Corrosion can affect the bond between reinforcing bars and concrete and hence the transfer of longitudinal stresses. Although a number of experimental studies on bond failure have been conducted in recent years, the findings have diverged rather widely, due primarily to differing test conditions. The present paper reports on an experimental programme consisting of eccentric pull-out tests run on corroded steel bars in specimens subjected to accelerated or natural corrosion. An axisymmetric bi-dimensional FE model with finite deformations initially developed to study bond mechanics with sound steel bars, has been enhanced to consider bond effects in corroded steel bars. The model simulation is compared to some of the experimental results for corroded and sound bars and the findings are analysed.

Application of PZT and FBG impedance sensors for structural health monitoring of reinforced concrete beams strengthened with FRP composite materials

Esta Tesis tiene como objetivo principal el desarrollo de métodos de identificación del daño que sean robustos y fiables, enfocados a sistemas estructurales experimentales, fundamentalmente a las estructuras de hormigón armado reforzadas externamente con bandas fibras de polímeros reforzados (FRP). El modo de fallo de este tipo de sistema estructural es crítico, pues generalmente es debido a un despegue repentino y frágil de la banda del refuerzo FRP originado en grietas intermedias causadas por la flexión. La detección de este despegue en su fase inicial es fundamental para prevenir fallos futuros, que pueden ser catastróficos. Inicialmente, se lleva a cabo una revisión del método de la Impedancia Electro-Mecánica (EMI), de cara a exponer sus capacidades para la detección de daño. Una vez la tecnología apropiada es seleccionada, lo que incluye un analizador de impedancias así como novedosos sensores PZT para monitorización inteligente, se ha diseñado un procedimiento automático basado en los registros de impedancias de distintas estructuras de laboratorio. Basándonos en el hecho de que las mediciones de impedancias son posibles gracias a una colocación adecuada de una red de sensores PZT, la estimación de la presencia de daño se realiza analizando los resultados de distintos indicadores de daño obtenidos de la literatura. Para que este proceso sea automático y que no sean necesarios conocimientos previos sobre el método EMI para realizar un experimento, se ha diseñado e implementado un Interfaz Gráfico de Usuario, transformando la medición de impedancias en un proceso fácil e intuitivo. Se evalúa entonces el daño a través de los correspondientes índices de daño, intentando estimar no sólo su severidad, sino también su localización aproximada. El desarrollo de estos experimentos en cualquier estructura genera grandes cantidades de datos que han de ser procesados, y algunas veces los índices de daño no son suficientes para una evaluación completa de la integridad de una estructura. En la mayoría de los casos se pueden encontrar patrones de daño en los datos, pero no se tiene información a priori del estado de la estructura. En este punto, se ha hecho una importante investigación en técnicas de reconocimiento de patrones particularmente en aprendizaje no supervisado, encontrando aplicaciones interesantes en el campo de la medicina. De ahí surge una idea creativa e innovadora: detectar y seguir la evolución del daño en distintas estructuras como si se tratase de un cáncer propagándose por el cuerpo humano. En ese sentido, las lecturas de impedancias se emplean como información intrínseca de la salud de la propia estructura, de forma que se pueden aplicar las mismas técnicas que las empleadas en la investigación del cáncer. En este caso, se ha aplicado un algoritmo de clasificación jerárquica dado que ilustra además la clasificación de los datos de forma gráfica, incluyendo información cualitativa y cuantitativa sobre el daño. Se ha investigado la efectividad de este procedimiento a través de tres estructuras de laboratorio, como son una viga de aluminio, una unión atornillada de aluminio y un bloque de hormigón reforzado con FRP. La primera ayuda a mostrar la efectividad del método en sencillos escenarios de daño simple y múltiple, de forma que las conclusiones extraídas se aplican sobre los otros dos, diseñados para simular condiciones de despegue en distintas estructuras. Demostrada la efectividad del método de clasificación jerárquica de lecturas de impedancias, se aplica el procedimiento sobre las estructuras de hormigón armado reforzadas con bandas de FRP objeto de esta tesis, detectando y clasificando cada estado de daño. Finalmente, y como alternativa al anterior procedimiento, se propone un método para la monitorización continua de la interfase FRP-Hormigón, a través de una red de sensores FBG permanentemente instalados en dicha interfase. De esta forma, se obtienen medidas de deformación de la interfase en condiciones de carga continua, para ser implementadas en un modelo de optimización multiobjetivo, cuya solución se haya por medio de una expansión multiobjetivo del método Particle Swarm Optimization (PSO). La fiabilidad de este último método de detección se investiga a través de sendos ejemplos tanto numéricos como experimentales. ABSTRACT This thesis aims to develop robust and reliable damage identification methods focused on experimental structural systems, in particular Reinforced Concrete (RC) structures externally strengthened with Fiber Reinforced Polymers (FRP) strips. The failure mode of this type of structural system is critical, since it is usually due to sudden and brittle debonding of the FRP reinforcement originating from intermediate flexural cracks. Detection of the debonding in its initial stage is essential thus to prevent future failure, which might be catastrophic. Initially, a revision of the Electro-Mechanical Impedance (EMI) method is carried out, in order to expose its capabilities for local damage detection. Once the appropriate technology is selected, which includes impedance analyzer as well as novel PZT sensors for smart monitoring, an automated procedure has been design based on the impedance signatures of several lab-scale structures. On the basis that capturing impedance measurements is possible thanks to an adequately deployed PZT sensor network, the estimation of damage presence is done by analyzing the results of different damage indices obtained from the literature. In order to make this process automatic so that it is not necessary a priori knowledge of the EMI method to carry out an experimental test, a Graphical User Interface has been designed, turning the impedance measurements into an easy and intuitive procedure. Damage is then assessed through the analysis of the corresponding damage indices, trying to estimate not only the damage severity, but also its approximate location. The development of these tests on any kind of structure generates large amounts of data to be processed, and sometimes the information provided by damage indices is not enough to achieve a complete analysis of the structural health condition. In most of the cases, some damage patterns can be found in the data, but none a priori knowledge of the health condition is given for any structure. At this point, an important research on pattern recognition techniques has been carried out, particularly on unsupervised learning techniques, finding interesting applications in the medicine field. From this investigation, a creative and innovative idea arose: to detect and track the evolution of damage in different structures, as if it were a cancer propagating through a human body. In that sense, the impedance signatures are used to give intrinsic information of the health condition of the structure, so that the same clustering algorithms applied in the cancer research can be applied to the problem addressed in this dissertation. Hierarchical clustering is then applied since it also provides a graphical display of the clustered data, including quantitative and qualitative information about damage. The performance of this approach is firstly investigated using three lab-scale structures, such as a simple aluminium beam, a bolt-jointed aluminium beam and an FRP-strengthened concrete specimen. The first one shows the performance of the method on simple single and multiple damage scenarios, so that the first conclusions can be extracted and applied to the other two experimental tests, which are designed to simulate a debonding condition on different structures. Once the performance of the impedance-based hierarchical clustering method is proven to be successful, it is then applied to the structural system studied in this dissertation, the RC structures externally strengthened with FRP strips, where the debonding failure in the interface between the FRP and the concrete is successfully detected and classified, proving thus the feasibility of this method. Finally, as an alternative to the previous approach, a continuous monitoring procedure of the FRP-Concrete interface is proposed, based on an FBGsensors Network permanently deployed within that interface. In this way, strain measurements can be obtained under controlled loading conditions, and then they are used in order to implement a multi-objective model updating method solved by a multi-objective expansion of the Particle Swarm Optimization (PSO) method. The feasibility of this last proposal is investigated and successfully proven on both numerical and experimental RC beams strengthened with FRP.