Energy Storage Systems for Electric Vehicles: Performance Comparison based on a Simple Equivalent Circuit and Experimental Tests

The decision to select the most suitable type of energy storage system for an electric vehicle is always difficult, since many conditionings must be taken into account. Sometimes, this study can be made by means of complex mathematical models which represent the behavior of a battery, ultracapacitor or some other devices. However, these models are usually too dependent on parameters that are not easily available, which usually results in nonrealistic results. Besides, the more accurate the model, the more specific it needs to be, which becomes an issue when comparing systems of different nature. This paper proposes a practical methodology to compare different energy storage technologies. This is done by means of a linear approach of an equivalent circuit based on laboratory tests. Via these tests, the internal resistance and the self-discharge rate are evaluated, making it possible to compare different energy storage systems regardless their technology. Rather simple testing equipment is sufficient to give a comparative idea of the differences between each system, concerning issues such as efficiency, heating and self-discharge, when operating under a certain scenario. The proposed methodology is applied to four energy storage systems of different nature for the sake of illustration.

PV self-consumption optimization with storage and Active DSM for the residential sector

With the rising prices of the retail electricity and the decreasing cost of the PV technology, grid parity with commercial electricity will soon become a reality in Europe. This fact, together with less attractive PV feed-in-tariffs in the near future and incentives to promote self-consumption suggest, that new operation modes for the PV Distributed Generation should be explored; differently from the traditional approach which is only based on maximizing the exported electricity to the grid. The smart metering is experiencing a growth in Europe and the United States but the possibilities of its use are still uncertain, in our system we propose their use to manage the storage and to allow the user to know their electrical power and energy balances. The ADSM has many benefits studied previously but also it has important challenges, in this paper we can observe and ADSM implementation example where we propose a solution to these challenges. In this paper we study the effects of the Active Demand-Side Management (ADSM) and storage systems in the amount of consumed local electrical energy. It has been developed on a prototype of a self-sufficient solar house called “MagicBox” equipped with grid connection, PV generation, lead–acid batteries, controllable appliances and smart metering. We carried out simulations for long-time experiments (yearly studies) and real measures for short and mid-time experiments (daily and weekly studies). Results show the relationship between the electricity flows and the storage capacity, which is not linear and becomes an important design criterion.

Effect of hen age, egg weight and storage system on physical properties of egg from white-egg laying hens

A total of 72 eggs from a group of 100 white laying hens housed in standard cages were analyzed. Thirty-six eggs were retired when the hens had 44 week of age and the other 36 eggs were retired eight weeks afterwards. Each group of 36 eggs was radomly divided in three groups of 12 eggs. First group was analyzed at once (storage system C); second one was kept during one week in the refrigerator (5ºC) (storage system R), and third group were kept also one week but on ambient temperature (25ºC) (storage system ET). The hen age, egg weight and storage system had not significant (P>0.05) effect on shell thickness. The specific gravity (SG) has a positive relation with shell quality. The egg class and storage system significantly (P<0,05) affected to SG, while no influence of bird age on this variable was observed. The yolk color increased with hen age but storage system had not effect on this variable. The increase of the hen age and the R and AT storage systems significantly (P<0.05) reduced albumen height (H) and the interaction hen age x storage system was significant (P<0.025) for this variable. The reduction of the H due to R and ET storage systems was higher in the eggs from hens with 52 weeks of age than in those from hens with 44 weeks of age. The Haugh units (HU) was significantly (P<0.05) affected by hen age, egg class and storage system. The hen age increase reduced HU and the R and ET eggs had lower HU than C eggs. It is concluded that the bird age and storage system with high temperatures reduced the egg quality.

An open-source simulation tool of grid-connected PV systems.

This paper will present an open-source simulation tool, which is being developed in the frame of an European research project1. The tool, whose final version will be freely available through a website, allows the modelling and the design of different types of grid-connected PV systems, such as large grid-connected plants and building-integrated installations. The tool is based on previous software developed by the IES-UPM2, whose models and energy losses scenarios have been validated in the commissioning of PV projects3 carried out in Spain, Portugal, France and Italy, whose aggregated capacity is nearly 300MW. This link between design and commissioning is one of the key points of tool presented here, which is not usually addressed by present commercial software. The tool provides, among other simulation results, the energy yield, the analysis and breakdown of energy losses, and the estimations of financial returns adapted to the legal and financial frameworks of each European country. Besides, educational facilities will be developed and integrated in the tool, not only devoted to learn how to use this software, but also to train the users on the best design PV systems practices. The tool will also include the recommendation of several PV community experts, which have been invited to identify present necessities in the field of PV systems simulation. For example, the possibility of using meteorological forecasts as input data, or modelling the integration of large energy storage systems, such as vanadium redox or lithium-ion batteries. Finally, it is worth mentioning that during the verification and testing stages of this software development, it will be also open to the suggestions received from the different actors of the PV community, such as promoters, installers, consultants, etc.

Graphene for energy storage

Due to its excellent mechanical, termal, optical and electrical properties, graphene has recently attracted increasing attention. It provides a huge surface area (2630m2 g-1) and high electrical conductivity, making it an attractive material for applications in energy-storage systems.

Estudio de un sistema de almacenamiento de energía eólica por medio de baterias

El objetivo de este trabajo consiste en evaluar los beneficios de la utilización de sistemas de almacenamiento de energía para incrementar el valor de un parque eólico. Debido a la naturaleza aleatoria inherente a la producción eléctrica de origen eólico, su integración en red plantea importantes problemas que suponen un reto tecnológico cada vez mayor a medida que la penetración de la energía eólica en el mix de generación aumenta. A su vez, las aplicaciones de los sistemas de almacenamiento de energía representan la oportunidad de mitigar los efectos indeseables de la producción eléctrica eólica. Los conocimientos adquiridos a lo largo de este proyecto se aplicarán para determinar qué sistema de almacenamiento de energía es óptimo para implantar en el parque eólico objeto del estudio, así como para cuantificar los beneficios derivados de la hibridación. ABSTRACT The aim of this work consist of assess the benefits of the use of energy storage systems for wind farm value enhacement. Due to the random nature inherent to wind electric generation, its grid integration carry important issues that represent a technology challenge that increases as wind generation penetration within energy mix increases as well. At the same time, energy storage systems applications represent an opportunity to mitigate the undesirable effects of wind generation. The knowledge gained throughout this project will be applied to determine which energy storage system is ideally suited for implementation within the wind farm under study, as well as quantify the benefits of hybridization.

Enhanced Failure Detection Mechanism in MapReduce

The popularity of MapReduce programming model has increased interest in the research community for its improvement. Among the other directions, the point of fault tolerance, concretely the failure detection issue seems to be a crucial one, but that until now has not reached its satisfying level. Motivated by this, I decided to devote my main research during this period into having a prototype system architecture of MapReduce framework with a new failure detection service, containing both analytical (theoretical) and implementation part. I am confident that this work should lead the way for further contributions in detecting failures to any NoSQL App frameworks, and cloud storage systems in general.

Flexible low-cost system to test batteries and ultracapacitors for electric and hybrid vehicles in real working conditions

Batteries and ultracapacitors for hybrid and electric vehicles must satisfy very demanding working conditions that are not usual in other applications. In this sense, specific tests must be performed in order to draw accurate conclusions about their behaviour. To do so, new advanced test benches are needed. These platforms must allow the study of a wide variety of energy storage systems under conditions similar to the real ones. In this paper, a flexible, low-cost and highly customizable system is presented. This system allows batteries and ultracapacitors to be tested in many and varied ways, effectively emulating the working conditions that they face in an electric vehicle. The platform was specifically designed to study energy storage systems for electric and hybrid vehicles, meaning that it is suitable to test different systems in many different working conditions, including real driving cycles. This flexibility is achieved keeping the cost of the platform low, which makes the proposed test bench a feasible alternative for the industry. As an example of the functionality of the platform, a test consisting of a 17-minute ARTEMIS urban cycle with a NiMH battery pack is presented.

Passive design strategies and performance of Net Energy Plus Houses

The first step in order to comply with the European Union goals of Near to Zero Energy Buildings is to reduce the energy consumption in buildings. Most of the building consumption is related to the use of active systems to maintain the interior comfort. Passive design strategies contribute to improve the interior comfort conditions, increasing the energy efficiency in buildings and reducing their energy consumption. In this work, an analysis of the passive strategies used in Net Energy Plus Houses has been made. The participating houses of the Solar Decathlon Europe 2012 competition were used as case studies. The passive design strategies of these houses were compared with the annual simulations, and the competition monitored data, especially during the Passive Monitored Period. The analysis included the thermal properties of the building envelope, geometric parameters, ratios and others passive solutions such as Thermal Energy Storage systems, evaporative cooling, night ventilation, solar gains and night sky radiation cooling. The results reflect the impact of passive design strategies on the houses' comfort and efficiency, as well as their influence in helping to achieve the Zero Energy Buildings category.

Improving photovoltaics grid integration through short time forecasting and self-consumption

The uncertainty associated to the forecast of photovoltaic generation is a major drawback for the widespread introduction of this technology into electricity grids. This uncertainty is a challenge in the design and operation of electrical systems that include photovoltaic generation. Demand-Side Management (DSM) techniques are widely used to modify energy consumption. If local photovoltaic generation is available, DSM techniques can use generation forecast to schedule the local consumption. On the other hand, local storage systems can be used to separate electricity availability from instantaneous generation; therefore, the effects of forecast error in the electrical system are reduced. The effects of uncertainty associated to the forecast of photovoltaic generation in a residential electrical system equipped with DSM techniques and a local storage system are analyzed in this paper. The study has been performed in a solar house that is able to displace a residential user?s load pattern, manage local storage and estimate forecasts of electricity generation. A series of real experiments and simulations have carried out on the house. The results of this experiments show that the use of Demand Side Management (DSM) and local storage reduces to 2% the uncertainty on the energy exchanged with the grid. In the case that the photovoltaic system would operate as a pure electricity generator feeding all generated electricity into grid, the uncertainty would raise to around 40%.

Optimización de la densidad de energía en vigas de material compuesto (PRF) sometidas a flexión pura

Las necesidades energéticas actuales requieren el desarrollo de tecnologías eficaces y eficientes en producción, transporte y distribución de energía. Estas necesidades han impulsado nuevos desarrollos en el ámbito energético, entre los cuales se encuentran sistemas de almacenamiento de energía. El avance en ingeniería de materiales permite pensar en la posibilidad de almacenamiento mediante deformación elástica de vigas. Concretamente se parte de un concepto de mecanismo acumulador de energía basado en la deformación elástica de resortes espirales a torsión. Dichos resortes se pueden considerar como elementos vigas sometidos a flexión pura y grandes deflexiones. Esta Tesis de centra en el diseño y optimización de estos elementos con el fin de maximizar la densidad de energía que son capaces de absorber. El proceso de optimización comienza con la identificación del factor crítico del que depende dicho proceso, en este caso de trata de la densidad de energía. Dicho factor depende de la geometría de la sección resistente y del material empleado en su construcción. En los últimos años ha existido un gran desarrollo de los materiales compuestos de tipo polimérico reforzados con fibras (PRF). Estos materiales están sustituyendo gradualmente a otros materiales, como los metales, debido principalmente a su excelente relación entre propiedades mecánicas y peso. Por otro lado, analizando las posibles geometrías para la sección resistente, se observó que la más adecuada es una estructura tipo sándwich. Se implementa así un procedimiento de diseño de vigas sándwich sometidas a flexión pura, con las pieles fabricadas en materiales compuestos tipo PRF y un núcleo que debe garantizar el bajo peso de la estructura. Se desarrolla así un procedimiento sistemático que se puede particularizar dependiendo de los parámetros de entrada de la viga, y que tiene en cuenta y analiza la aparición de todos los posibles modos de fallo posibles. Así mismo se desarrollan una serie de mapas o ábacos de diseño que permiten seleccionar rápidamente las dimensiones preliminares de la viga. Finalmente se llevan a cabo ensayos que permiten, por un lado, validar el concepto del mecanismo acumulador de energía a través del ensayo de un muelle con sección monolítica, y por otro validar los distintos diseños de vigas sándwich propuestos y mostrar el incremento de la densidad de energía con respecto a la alternativa monolítica. Como líneas futuras de investigación se plantean la investigación en nuevos materiales, como la utilización de nanotubos de carbono, y la optimización del mecanismo de absorción de energía; optimizando el mecanismo de absorción a flexión pura e implementando sistemas que permitan acumular energía mediante la deformación elástica debida a esfuerzos de tracción-compresión. ABSTRACT Energy supply requires the development of effective and efficient technologies for the production, transport and distribution of energy. In recent years, many energy storage systems have been developed. Advances in the field of materials engineering has allowed the development of new concepts as the energy storage by elastic deformation of beams. Particularly, in this Thesis an energy storage device based on the elastic deformation of torsional springs has been studied. These springs can be considered as beam elements subjected to pure bending loads and large deflections. This Thesis is focused on the design and optimization of these beam elements in order to maximize its density of stored energy. The optimization process starts with the identification of the critical factors for the elastic energy storage: the density. This factor depends on the geometry of the cross section of the beam and the materials from which it is made. In the last 20 years, major advances in the field of composite materials have been made, particularly in the field of fiber reinforced polymers (FRP). This type of material is substituting gradually metallic materials to their excellent weight-mechanical properties ratio. In the other side, several possible geometries are analyzed for its use in the cross section of the beam; it was concluded that the best option, for maximum energy density, is using a sandwich beam. A design procedure for sandwich beams with skins made up with FRP composites and a light weight core is developed. This procedure can be particularized for different input parameters and it analyzes all the possible failure modes. Abacus and failure mode maps have been developed in order to simplify the design process. Finally several tested was made. Firstly, a prototype of the energy storage system which uses a monolithic composite beam was tested in order to validate the concept of the energy storage by elastic deformation. After that sandwich beam samples are built and tested, validating the design and showing the increase of energy density with respect to the monolithic beam. As futures research lines the following are proposed: research in new materials, as carbon nanotubes; and the optimization of the energy storage mechanism, that means optimizing the pure bending storage mechanism and developing new ones based on traction-compression mechanisms.

Fuel Cells: A Real Option for Unmanned Aerial Vehicles Propulsion

The possibility of implementing fuel cell technology in Unmanned Aerial Vehicle (UAV) propulsion systems is considered. Potential advantages of the Proton Exchange Membrane or Polymer Electrolyte Membrane (PEMFC) and Direct Methanol Fuel Cells (DMFC), their fuels (hydrogen and methanol), and their storage systems are revised from technical and environmental standpoints. Some operating commercial applications are described. Main constraints for these kinds of fuel cells are analyzed in order to elucidate the viability of future developments. Since the low power density is the main problem of fuel cells, hybridization with electric batteries, necessary in most cases, is also explored.

Co-simulation Methodologies for Hybrid and Electric Vehicle Dynamics

In recent decades, full electric and hybrid electric vehicles have emerged as an alternative to conventional cars due to a range of factors, including environmental and economic aspects. These vehicles are the result of considerable efforts to seek ways of reducing the use of fossil fuel for vehicle propulsion. Sophisticated technologies such as hybrid and electric powertrains require careful study and optimization. Mathematical models play a key role at this point. Currently, many advanced mathematical analysis tools, as well as computer applications have been built for vehicle simulation purposes. Given the great interest of hybrid and electric powertrains, along with the increasing importance of reliable computer-based models, the author decided to integrate both aspects in the research purpose of this work. Furthermore, this is one of the first final degree projects held at the ETSII (Higher Technical School of Industrial Engineers) that covers the study of hybrid and electric propulsion systems. The present project is based on MBS3D 2.0, a specialized software for the dynamic simulation of multibody systems developed at the UPM Institute of Automobile Research (INSIA). Automobiles are a clear example of complex multibody systems, which are present in nearly every field of engineering. The work presented here benefits from the availability of MBS3D software. This program has proven to be a very efficient tool, with a highly developed underlying mathematical formulation. On this basis, the focus of this project is the extension of MBS3D features in order to be able to perform dynamic simulations of hybrid and electric vehicle models. This requires the joint simulation of the mechanical model of the vehicle, together with the model of the hybrid or electric powertrain. These sub-models belong to completely different physical domains. In fact the powertrain consists of energy storage systems, electrical machines and power electronics, connected to purely mechanical components (wheels, suspension, transmission, clutch…). The challenge today is to create a global vehicle model that is valid for computer simulation. Therefore, the main goal of this project is to apply co-simulation methodologies to a comprehensive model of an electric vehicle, where sub-models from different areas of engineering are coupled. The created electric vehicle (EV) model consists of a separately excited DC electric motor, a Li-ion battery pack, a DC/DC chopper converter and a multibody vehicle model. Co-simulation techniques allow car designers to simulate complex vehicle architectures and behaviors, which are usually difficult to implement in a real environment due to safety and/or economic reasons. In addition, multi-domain computational models help to detect the effects of different driving patterns and parameters and improve the models in a fast and effective way. Automotive designers can greatly benefit from a multidisciplinary approach of new hybrid and electric vehicles. In this case, the global electric vehicle model includes an electrical subsystem and a mechanical subsystem. The electrical subsystem consists of three basic components: electric motor, battery pack and power converter. A modular representation is used for building the dynamic model of the vehicle drivetrain. This means that every component of the drivetrain (submodule) is modeled separately and has its own general dynamic model, with clearly defined inputs and outputs. Then, all the particular submodules are assembled according to the drivetrain configuration and, in this way, the power flow across the components is completely determined. Dynamic models of electrical components are often based on equivalent circuits, where Kirchhoff’s voltage and current laws are applied to draw the algebraic and differential equations. Here, Randles circuit is used for dynamic modeling of the battery and the electric motor is modeled through the analysis of the equivalent circuit of a separately excited DC motor, where the power converter is included. The mechanical subsystem is defined by MBS3D equations. These equations consider the position, velocity and acceleration of all the bodies comprising the vehicle multibody system. MBS3D 2.0 is entirely written in MATLAB and the structure of the program has been thoroughly studied and understood by the author. MBS3D software is adapted according to the requirements of the applied co-simulation method. Some of the core functions are modified, such as integrator and graphics, and several auxiliary functions are added in order to compute the mathematical model of the electrical components. By coupling and co-simulating both subsystems, it is possible to evaluate the dynamic interaction among all the components of the drivetrain. ‘Tight-coupling’ method is used to cosimulate the sub-models. This approach integrates all subsystems simultaneously and the results of the integration are exchanged by function-call. This means that the integration is done jointly for the mechanical and the electrical subsystem, under a single integrator and then, the speed of integration is determined by the slower subsystem. Simulations are then used to show the performance of the developed EV model. However, this project focuses more on the validation of the computational and mathematical tool for electric and hybrid vehicle simulation. For this purpose, a detailed study and comparison of different integrators within the MATLAB environment is done. Consequently, the main efforts are directed towards the implementation of co-simulation techniques in MBS3D software. In this regard, it is not intended to create an extremely precise EV model in terms of real vehicle performance, although an acceptable level of accuracy is achieved. The gap between the EV model and the real system is filled, in a way, by introducing the gas and brake pedals input, which reflects the actual driver behavior. This input is included directly in the differential equations of the model, and determines the amount of current provided to the electric motor. For a separately excited DC motor, the rotor current is proportional to the traction torque delivered to the car wheels. Therefore, as it occurs in the case of real vehicle models, the propulsion torque in the mathematical model is controlled through acceleration and brake pedal commands. The designed transmission system also includes a reduction gear that adapts the torque coming for the motor drive and transfers it. The main contribution of this project is, therefore, the implementation of a new calculation path for the wheel torques, based on performance characteristics and outputs of the electric powertrain model. Originally, the wheel traction and braking torques were input to MBS3D through a vector directly computed by the user in a MATLAB script. Now, they are calculated as a function of the motor current which, in turn, depends on the current provided by the battery pack across the DC/DC chopper converter. The motor and battery currents and voltages are the solutions of the electrical ODE (Ordinary Differential Equation) system coupled to the multibody system. Simultaneously, the outputs of MBS3D model are the position, velocity and acceleration of the vehicle at all times. The motor shaft speed is computed from the output vehicle speed considering the wheel radius, the gear reduction ratio and the transmission efficiency. This motor shaft speed, somehow available from MBS3D model, is then introduced in the differential equations corresponding to the electrical subsystem. In this way, MBS3D and the electrical powertrain model are interconnected and both subsystems exchange values resulting as expected with tight-coupling approach.When programming mathematical models of complex systems, code optimization is a key step in the process. A way to improve the overall performance of the integration, making use of C/C++ as an alternative programming language, is described and implemented. Although this entails a higher computational burden, it leads to important advantages regarding cosimulation speed and stability. In order to do this, it is necessary to integrate MATLAB with another integrated development environment (IDE), where C/C++ code can be generated and executed. In this project, C/C++ files are programmed in Microsoft Visual Studio and the interface between both IDEs is created by building C/C++ MEX file functions. These programs contain functions or subroutines that can be dynamically linked and executed from MATLAB. This process achieves reductions in simulation time up to two orders of magnitude. The tests performed with different integrators, also reveal the stiff character of the differential equations corresponding to the electrical subsystem, and allow the improvement of the cosimulation process. When varying the parameters of the integration and/or the initial conditions of the problem, the solutions of the system of equations show better dynamic response and stability, depending on the integrator used. Several integrators, with variable and non-variable step-size, and for stiff and non-stiff problems are applied to the coupled ODE system. Then, the results are analyzed, compared and discussed. From all the above, the project can be divided into four main parts: 1. Creation of the equation-based electric vehicle model; 2. Programming, simulation and adjustment of the electric vehicle model; 3. Application of co-simulation methodologies to MBS3D and the electric powertrain subsystem; and 4. Code optimization and study of different integrators. Additionally, in order to deeply understand the context of the project, the first chapters include an introduction to basic vehicle dynamics, current classification of hybrid and electric vehicles and an explanation of the involved technologies such as brake energy regeneration, electric and non-electric propulsion systems for EVs and HEVs (hybrid electric vehicles) and their control strategies. Later, the problem of dynamic modeling of hybrid and electric vehicles is discussed. The integrated development environment and the simulation tool are also briefly described. The core chapters include an explanation of the major co-simulation methodologies and how they have been programmed and applied to the electric powertrain model together with the multibody system dynamic model. Finally, the last chapters summarize the main results and conclusions of the project and propose further research topics. In conclusion, co-simulation methodologies are applicable within the integrated development environments MATLAB and Visual Studio, and the simulation tool MBS3D 2.0, where equation-based models of multidisciplinary subsystems, consisting of mechanical and electrical components, are coupled and integrated in a very efficient way.

Entorno sin cinta para producción de televisión en alta definición

En este proyecto se propone un entorno de producción para televisión en alta definición donde las cintas magnéticas para la captura, modificación, gestión y transferencia de los contenidos audiovisuales, quedan sustituidas por servidores informáticos y sistemas de almacenamiento basados en las tecnologías de la información. Dicho entorno sin cintas tiene como misión la realización de la fase de la producción de los contenidos televisivos. Se trata de un centra independiente, en una ubicación remota respecto a las instalaciones centrales de la empresa emisora de televisión. La conexión del entorno sin cinta con los servicios centrales de la cadena se realiza por medio de redes de datos de alta velocidad y por enlace de radiofrecuencia. Por estos medios los sistemas de redacción comunican datos y escaletas, se reciben las señales de contribución que intervienen en los programas, se envía la serial realizada para emisión y se transfieren los materiales grabados al área de Postproducción para su elaboración final. Se plantean dos estudios de televisión dotados de servidores de video y de un almacenamiento compartido para una gestión ágil, unificada y flexible de las demandas de los programas. Además de la eliminación del lento y pesado trabajo de manipulación de las cintas, la producción resulta mucho mas ágil porque se eliminan tiempos de espera por la posibilidad de acceso simultaneo de varios usuarios a un mismo contenido. También se suprimen los tiempos de digitalización y descarga del material grabado, porque los sistemas implementados permiten la ingesta directa de las señales recibidas. Los contenidos de varias jornadas de grabación, en calidad HD, se conservan en el sistema de almacenamiento para la elaboración de materiales en el propio centra y para su transferencia al departamento central correspondiente. Mediante aplicaciones software se busca la integración del trabajo de la redacción de los programas con los procesos de producción de los estudios. El diseño que se propone para los diferentes subsistemas técnicos de los estudios esta orientado a lograr una alta fiabilidad, operatividad y adaptabilidad a las demandas técnicas de la producción audiovisual de los diferentes tipos de programas. Al tratarse de una propuesta conceptual, de manera general no se basa en equipos de marcas o fabricantes concretos sino mas bien en las metodologías concretas de trabajo. Cuando se ejemplifica algún dispositivo en particular es debido a que el concepto tecnológico del mismo es novedoso destaca de manera especial sobre la generalidad de los equipos existentes para esa funcionalidad. ABSTRACT. This project hopes to propose a television production platform that uses computers, servers and storage systems based on information technologies, rather than video tape recorders for ingesting, editing and making TV programs. This tapeless system has as its mission the production of all kind of television contents, employing IT systems, without the use of magnetic tapes. We envision an independent TV production center located in a remote location, in relation to the main broadcaster facilities, where all communications between this broadcasting center and the remote independent tapeless center would occur via high speed internet and a radiofrequency link as a back up. In this way, the Newsroom systems communicate data and rundowns; contribution feeds are received; PGM signal are codified and transmitted; and stored media are transferred to the post production area for final editing, playout and archive. Two TV studios are proposed, equipped with video servers and sharing media storage for agile, unified and flexible management of the production requirements. Apart from completely eliminating the slow and hard work resulting from handling a lot of traditional magnetic tapes, the production ends up being much quicker due to the fact that there is no waiting time between recording and viewing. This also enables several users to access and view the same material at the same time. The digitalization and downloading time is also greatly reduced due to the direct ingestion of contribution feeds to the system. The HD content of various days of recording, are stored for future use for whichever department needs the footage in the future. Through software applications, there will be complete integration between the Newsroom work and the production process of the studios. The proposed design for the various technical subsystems in the recording studio is directed towards achieving optimum reliability and operational capability: they are easily adaptable to the technical demands of the audiovisual production of the different programs. Because we are dealing with a conceptual proposal, in general terms, we are not defining the brands or manufacturers of the technical equipment, but rather we are specifying the methods which we plan to implement. When some equipment is highlighted, it's only because that specific brand exemplifies a higher performance than any other equipment in the range.

Criterios técnicos del proyecto con módulos tridimensionales ligeros: las casas del Solar Decathlon 2005 y 2007

Este trabajo se ocupa de la construcción modular ligera de viviendas unifamiliares, más concretamente aborda el problema de la definición constructiva de las mismas, habida cuenta de lo poco conocido y publicado de este aspecto en particular. Dado que la construcción es fruto de la evolución, resulta de gran importancia el estudio de los antecedentes para comprender la situación actual, por ello para documentar como corresponde el estado de la técnica y de la investigación se estudiaron los antecedentes desde sus primeras manifestaciones a finales del siglo XIX hasta nuestros días. Contrariamente a las profecías de Le Corbusier y otros, la industrialización no ha llegado a la construcción ni en la forma ni en la medida que era de esperar a principios del siglo XX. Sin embargo y a pesar del relativo “fracaso” de la industrialización en convertirse en la forma mayoritaria de producir edificios, lo cierto es que algunos sistemas altamente industrializados, como lo es la construcción modular ligera, han logrado un lugar en el mercado, que en algunos países resulta cuanto menos significativo. Delimitar el estado de la técnica y la situación actual es crucial en este trabajo, toda vez que la construcción industrializada la realizan empresas, y situarse al margen de las mismas y de su producción, nos guste o no, resulta contrario al sentido común. De este modo se han identificado y documentado ejemplos como el de EE.UU. y Japón, entre otros, que resultan muy ilustrativos tanto desde la evolución como del estado actual. Del estado de la técnica y la investigación también resulta la escasez de publicación de detalles constructivos específicos de la construcción modular ligera. Es obvio que los fabricantes intentan blindarse mediante el secreto industrial, logrando que las soluciones constructivas más interesantes queden fuertemente protegidas dentro del conocimiento reservado de la empresa. De este modo un sistema que alcanza grados de prefabricación del 95%, tan atractivo e interesante para el arquitecto queda reservado al conocimiento de unos pocos dentro de las empresas. La búsqueda de mayor información sobre estos sistemas encuentra un filón indiscutible en los proyectos de las casas del concurso Solar Decathlon. En efecto, debido a las condiciones particulares de este concurso, las casas que compiten deben ser instaladas en un plazo corto, por lo que en su mayoría recurren al método de construcción modular ligera, para lograr correctamente este objetivo. Adicionalmente todos los planos de proyecto incluidos los de detalle, así como memorias de especificaciones técnicas, quedan colgadas en la Web, a libre disposición del público. De este modo se ha considerado interesante, conveniente y útil, aprovechar como fuente documental de este trabajo, aparte de lo obtenido en el estado de la técnica y la investigación, los proyectos de las casas de los concursos 2005 y 2007, que fueron las dos últimas ediciones celebradas cuando se inició esta tesis. De modo similar a esta carencia de detalles publicados se observa igualmente una falta de investigación y de metodologías adecuadas a la misma sobre soluciones y detalles constructivos propios de la construcción modular ligera. Por eso y ante la dificultad de manejar adecuadamente una información disponible pero farragosa, este trabajo ha dedicado una parte importante de su esfuerzo a la creación de una metodología adecuada a este tipo de situación. Hay que destacar que cada proyecto puede constar fácilmente de 60 a casi 200 planos, sin contar las memorias técnicas y otros documentos, tales como galerías de imágenes, etc. Por otra parte resulta útil establecer esta metodología, no solo para esta tesis, sino para futuros trabajos de investigación sobre el tema, toda vez que con posterioridad a 2007 se han celebrado nuevas ediciones del concurso con su correspondiente volumen de información disponible. La metodología del análisis de los proyectos se basa en el diseño y creación de siete fichas tipo que resumen los aspectos fundamentales del proyecto desde el punto de vista constructivo, permitiendo de este modo su rápida visualización y comprensión sin pretender exhaustividad, ya que en caso de querer profundizar en el detalle de la información siempre está el proyecto original para ello. Tras estudiar la información obtenida de los proyectos de las casas de concurso, se contrastan y discuten los resultados para obtener conocimientos de interés para el objetivo propuesto en la tesis. Se comparan los resultados procedentes del estado de la técnica y de la investigación y se obtienen las conclusiones correspondientes. De este modo ha sido posible identificar una serie de criterios técnicos de proyecto de viviendas unifamiliares realizadas mediante construcción modular ligera, que además se organizan en varios niveles, por lo que el resultado es un conjunto de criterios como germen de una futura guía o manual. Como conclusiones fundamentales de la tesis hay que destacar las metodológicas, que habilitan la extensión de este estudio a otros trabajos y la aportación original al conocimiento con la definición de una serie de criterios técnicos de proyecto de viviendas realizadas mediante construcción modular ligera, que además de mejorar esta parte del saber constructivo serán de gran ayuda a los arquitectos de cara a la reducción de errores, que a menudo derivan en mayores costes y plazos, cuando no directamente al abandono del sistema constructivo. El trabajo de la tesis se estructura en siete capítulos a saber: Capítulo 1: Introducción, donde se explica el tema de la tesis, el objetivo principal, las limitaciones y se aportan algunas definiciones. Capítulo 2: Estado de la técnica y la investigación, dentro del cual se presentan los antecedentes desde sus inicios pasando por la primera y segunda mitad del siglo XX y finalizando con el estado actual que recorre los sistemas de EE.UU, Japón, Europa, Escandinavia, centro Europa, Francia, España y algunos ejemplos de Latinoamérica. En el estado de la investigación se presentan las publicaciones tanto en revistas científicas indexadas en el JCR, como publicaciones no indexadas en las que se muestran artículos científicos, comunicaciones a congresos, documentación sobre el concurso Solar Decathlon, libros específicos y libros genéricos sobre construcción modular ligera, tesis doctorales tanto generales como específicas sobre el concurso Solar Decathlon, documentos de idoneidad técnica, páginas Web del concurso Solar Decathlon y finalmente páginas Web de empresas de construcción modular ligera y patentes. También se expresan las conclusiones parciales del capítulo así también como la justificación y los objetivos particulares. Capítulo 3: Metodología, se expone en primer lugar el planteamiento del problema, para luego desarrollar los métodos utilizados para el estudio y clasificación del transporte y de la organización modular, la relación entre la organización modular y distribución espacial, el diseño y contenido de las fichas resumen de los 38 proyectos presentados al SD2005 y SD2007, así también como la información consultada para su realización. Se explica asimismo como se realizaron las tablas comparativas partiendo de la información de las fichas. Finalmente se expresa la manera en que se trató el estudio particular de la junta entre módulos. Capítulo 4: Discusión de resultados, dónde en primer lugar se presenta la clasificación y las estrategias del transporte así también como una clasificación de la organización modular, en segundo lugar se estudian las relaciones que existen entre el sistema modular y la organización espacial. A partir de aquí se muestra el estudio de la estructura de todas las casas del SD2005 y SD2007, según el tipo y material de las zapatas, mostrando tanto tablas cuantitativas como tablas gráficas con fotos. De la misma manera se tratan los forjados, los pilares y las vigas y las cubiertas. Se estudia además el cerramiento opaco y acristalado, la cubierta y el forjado según las capas que lo componen. En el caso de las instalaciones se estudian las que son especiales, descartando las normales en este tipo de casas, como son los paneles fotovoltaicos, placas térmicas o tubos de vacío y los sistemas de almacenamiento de energía, como las baterías, presentando tablas numéricas y gráficas con fotos. El transporte se analiza según corresponda al traslado de la vivienda o al transporte de apoyo, según el tipo y la cantidad utilizado. Con respecto al montaje se diferencia en si se usó grúa o no, y en el caso de no utilizarse se muestran los métodos alternativos. Con respecto a la exploración de la organización modular se presentan la cantidad de módulos que utilizó cada casa, así como también la cuantificación de los sistemas híbridos como son elementos lineales 1D, paneles 2D. Por último se muestra el estudio detallado de la junta entre módulos 3D. Finalmente se realiza la propuesta de un conjunto de criterios técnicos de proyecto organizado en cuatro niveles: 1º nivel de criterios generales, 2º nivel sobre sistemas constructivos, 3º nivel de detalles constructivos y el 4º nivel llamado logística obras previas, transporte y montaje. Capítulo 5: Conclusiones y líneas futuras de investigación, se exponen las conclusiones generales, metodológicas, documentales y por último las de construcción modular. Finalmente se realiza una propuesta de líneas futuras de investigación. Capítulo 6: Bibliografía. Capítulo 7: Anexos, en el que se presentan todas las fichas resumen de las casas realizadas por el autor de esta tesis. Además se incluyen los casos concretos de Voisin en Francia y la TVA (Tennessee Valley Authority) en EE.UU., así como referencias de manuales genéricos de construcción ligera, medidas de transporte en España e información sobre estadísticas de viviendas en la Unión Europea. ABSTRACT This paper deals with Light Modular Construction of houses, and specifically addresses the problem of the constructive definition of the same, given how little known and published this subject has been. Since building construction is the result of evolution, it is of great importance to study its background for understanding the current situation, therefore to document the state of the art and research, its history was studied from its origins dating to the end nineteenth century to our days. Contrary to the prophecies of Le Corbusier and others, industrialization has not reached the construction neither in the form nor to the extent that it was expected in the early twentieth century. However, despite the relative "failure" of industrialization to become the major form of production for buildings, the fact is that some highly industrialized systems, such as the so called Lightweight Modular Construction, have achieved a place in the market, which in some countries is at least significant. To outline the state of the art and the current situation is crucial in this work, since industrialized construction is carried out by companies, and to step away from them and their production, whether we like it or not, it is contrary to common sense. So that, several cases have been identified and documented, such as the US and Japan examples, among others, which are very illustrative both from evolution and the current status. The state of the art and research shows also a shortage of publication of specific construction details of light modular construction. Obviously, manufacturers try to shield themselves by trade secret, making the most interesting constructive solutions remain heavily protected within the reserved knowledge of the company, so a system that reaches levels of 95% prefabrication, so attractive and interesting for the architect It is reserved to the knowledge of a few people inside the companies. The search for more information on these systems finds an invaluable reef in the projects of the Solar Decathlon houses. Indeed, due to the particular conditions of this contest, houses competing must be installed in a short time, so mostly turn to modular construction methods for this purpose to achieve properly this goal. Additionally all levels of project, including detailed and technical specifications reports are published on the Web, freely available to the general public. Thus it was considered interesting, convenient and useful to take advantage as a documentary source of this work, apart from what it were obtained in the state of the art and research, the projects of the houses of the 2005 and 2007 contests, which were the last two editions already held before this thesis was started. Similar to this lack of published details it is also observed a lack of research and methodologies adapted to the solutions and construction details of lightweight modular construction. So that, and facing the difficulty of adequately manage the available but bulky information, this work has devoted a significant part of its effort to create an appropriate methodology for this type of situation. It is noteworthy that each project can easily consist of 60 to almost 200 blueprints, not including technical reports and other documents, such as photo galleries, etc. The methodology of the analysis of the projects is based on the design and creation of seven record sheets that summarize key aspects of the project from a construction point of view, thus allowing quick watching and understanding of the project, without claiming completeness, always keeping for further information the blueprints themselves. After studying the information obtained from the projects of the competition houses, the results are compared and discussed to obtain relevant knowledge according to the objective proposed in the thesis. The results from the state of the art and research are also compared and the conclusions so obtained make possible to identify a number of technical design criteria for single family homes made using lightweight modular construction, which also have been organized at various levels, so the result is a set of criteria as a seed for a future guide or manual. Among the main conclusions of the thesis must be noted the methodological ones, that enable the extension of this study to other works and are an original contribution to knowledge with the definition of a number of technical criteria for housing projects made by light modular construction, what in addition to improving this part of the constructive knowledge will be of great help for the architects to reduce errors that often result in higher costs and delays, if not in abandonment of the construction system itself. The work of the thesis is divided into seven chapters as follows: Chapter 1: Introduction, where the topic of the thesis, the main objective, limitations and the provided definitions is explained. Chapter 2: State of the art and research, within which history is presented from the beginning through the first and second half of the twentieth century and ending with the current systems, that spans from the USA to Japan, Europe, Scandinavia, Central Europe, France, Spain and some Latin American examples. In the state of research publications are presented both on scientific journals indexed in the JCR, and non-indexed publications in which scientific articles, conference papers, information about the Solar Decathlon competition, generic and specific books on light modular construction, articles both general and specific on the Solar Decathlon competition, technical approval documents, dissertations, the Solar Decathlon Web pages and finally lightweight modular construction companies Web pages and patents. The partial conclusions of the chapter as well as the rationale and specific objectives are also expressed. Chapter 3: Methodology first of all exposes the problem statement and then develops the methods used for the study and classification of transportation and modular organization, the relationship between the modular organization and spatial distribution, design and content summary records of the 38 projects submitted to the SD2005 and SD2007, as well as information consulted for its realization. It explains equally how the comparative tables based on information from the chips were made. Finally, the way the particular study of the joint between modules is carried out is also treated. Chapter 4: Discussion, first sorting a classification of transport strategies as well as of modular organization, secondly the relationship between the modular system and the spatial organization studied is presented. From then on, the study of the structure of every house Moreover, to establish this methodology is useful not only for this thesis, but for future research on the subject, since after 2007 there have been held new editions of the contest with a corresponding volume of information available. shown in the SD2005 and SD2007 contests, depending on the type and material of the shoe, showing both quantitative tables as graphic boards with pictures is carried out. Similarly slabs, columns and beams and roofs are treated. Furthermore, the opaque and transparent façades, as well as roof and floor enclosure, according to the layers that compose them are studied. In the case of facilities there have been only addressed that which are of a special type, discarding that considered usual in this type of houses such as photovoltaic panels, thermal panels or vacuum tubes and energy storage systems such as batteries, presenting numerical and graphical tables with photos .The transportation is analyzed depending on it is used to move the house or for additional support, depending on the type and quantity of items used. Regarding assembly it has been made a difference if crane is or not used and if not, what the alternative methods are. With respect to the exploration of the modular organization, the amount of modules used in each house is presented, as well as the quantification of hybrid systems such as linear members as well as 1D, 2D panels. Finally, it has been carried out the detailed study of the joint between 3D modules. Finally it is proposed a set of technical criteria organized into four levels, 1st level of general criteria, 2nd level on building systems, 3rd level construction details and 4th level called previous works and logistics, transportation and assembly. Chapter 5: Conclusions and future research, where general, methodological, documentary and finally modular construction findings are presented. A proposal for further research is done. Chapter 6: Bibliography. Chapter 7: Annexes, in which all the record sheets of houses made by the author of this thesis are presented. Besides the specific cases of Voisin in France and TVA (Tennessee Valley Authority) in the USA, as well as general reference manuals on lightweight construction, transportation dimensions in Spain, and information on housing statistics in the European Union are included.