Behaviour of dolomite, olivine and alumina as primary catalysts in air-steam gasification of sewage sludge

Sewage sludge gasification assays were performed in an atmospheric fluidised bed reactor using air and air–steam mixtures as the gasifying agents. Dolomite, olivine and alumina are three well known tar removal catalysts used in biomass gasification processing. However, little information is available regarding their performance in sewage sludge gasification. The aim of the current study was to learn about the influence of these three catalysts in the product distribution and tar production during sewage sludge gasification. To this end, a set of assays was performed in which the temperature (750–850 °C), the in-bed catalyst content (0, 10 and 15 wt.%) and the steam–biomass ratio (SB) in the range of 0–1 were varied with a constant equivalence ratio (ER) of 0.3. The results were compared to the results from gasification without a catalyst. We show that dolomite has the highest activity in tar elimination, followed by alumina and olivine. In addition to improving tar removal, the presence of water vapour and the catalysts increased the content of H2 in the gases by nearly 60%.

Air-steam gasification of sewage sludge in a bubbling bed reactor: Effect of alumina as a primary catalyst

Numerous references can be found in scientific literature regarding biomass gasification. However, there are few works related to sludge gasification. A study of sewage sludge gasification process in a bubbling fluidised bed gasifier on a laboratory scale is here reported. The aim was to find the optimum conditions for reducing the production of tars and gain more information on the influx of different operating variables in the products resulting from the gasification of this waste. The variables studied were the equivalence ratio (ER), the steam-biomass ratio (SB) and temperature. Specifically, the ER was varied from 0.2 to 0.4, the SB from 0 to 1 and the temperature from 750 °C (1023 K) to 850 °C (1123 K). Although it was observed that tar production could be considerably reduced (up to 72%) by optimising the gasification conditions, the effect of using alumina (aluminium oxide, of proven efficacy in destroying the tar produced in biomass gasification) as primary catalyst in air and air-steam mixture tests was also verified. The results show that by adding small quantities of alumina to the bed (10% by weight of fed sludge) considerable reductions in tar production can be obtained (up to 42%) improving, at the same time, the lower heating value (LHV) of the gas and carbon conversion.

A simplified Probabilistic Safety Assesment of a Steam-Methane Reforming Hydrogen Production Plant coupled to a High-Temperature Gas Cooled Nuclear Reactor

A Probabilistic Safety Assessment (PSA) is being developed for a steam-methane reforming hydrogen production plant linked to a High-Temperature Gas Cooled Nuclear Reactor (HTGR). This work is based on the Japan Atomic Energy Research Institute’s (JAERI) High Temperature Test Reactor (HTTR) prototype in Japan. This study has two major objectives: calculate the risk to onsite and offsite individuals, and calculate the frequency of different types of damage to the complex. A simplified HAZOP study was performed to identify initiating events, based on existing studies. The initiating events presented here are methane pipe break, helium pipe break, and PPWC heat exchanger pipe break. Generic data was used for the fault tree analysis and the initiating event frequency. Saphire was used for the PSA analysis. The results show that the average frequency of an accident at this complex is 2.5E-06, which is divided into the various end states. The dominant sequences result in graphite oxidation which does not pose a health risk to the population. The dominant sequences that could affect the population are those that result in a methane explosion and occur 6.6E-8/year, while the other sequences are much less frequent. The health risk presents itself if there are people in the vicinity who could be affected by the explosion. This analysis also demonstrates that an accident in one of the plants has little effect on the other. This is true given the design base distance between the plants, the fact that the reactor is underground, as well as other safety characteristics of the HTGR. Sensitivity studies are being performed in order to determine where additional and improved data is needed.

Application of a dynamic event tree methodolgy to steam generator tube rupture sequences

The Integrated Safety Assessment (ISA) methodology, developed by the Spanish Nuclear Safety Council (CSN), has been applied to a thermo-hydraulical analysis of a Westinghouse 3-loop PWR plant by means of the dynamic event trees (DET) for Steam Generator Tube Rupture (SGTR) sequences. The ISA methodology allows obtaining the SGTR Dynamic Event Tree taking into account the operator actuation times. Simulations are performed with SCAIS (Simulation Code system for Integrated Safety Assessment), which includes a dynamic coupling with MAAP thermal hydraulic code. The results show the capability of the ISA methodology and SCAIS platform to obtain the DET of complex sequences.

SolarPaces 2013: Innovations on direct steam generation in linear fresnel collectors

Direct Steam Generation (DSG) in Linear Fresnel (LF) solar collectors is being consolidated as a feasible technology for Concentrating Solar Power (CSP) plants. The competitiveness of this technology relies on the following main features: water as heat transfer fluid (HTF) in Solar Field (SF), obtaining high superheated steam temperatures and pressures at turbine inlet (500ºC and 90 bar), no heat tracing required to avoid HTF freezing, no HTF degradation, no environmental impacts, any heat exchanger between SF and Balance Of Plant (BOP), and low cost installation and maintenance. Regarding to LF solar collectors, were recently developed as an alternative to Parabolic Trough Collector (PTC) technology. The main advantages of LF are: the reduced collector manufacturing cost and maintenance, linear mirrors shapes versus parabolic mirror, fixed receiver pipes (no ball joints reducing leaking for high pressures), lower susceptibility to wind damages, and light supporting structures allowing reduced driving devices. Companies as Novatec, Areva, Solar Euromed, etc., are investing in LF DSG technology and constructing different pilot plants to demonstrate the benefits and feasibility of this solution for defined locations and conditions (Puerto Errado 1 and 2 in Murcia Spain, Lidellin Newcastle Australia, Kogran Creek in South West Queensland Australia, Kimberlina in Bakersfield California USA, Llo Solar in Pyrénées France,Dhursar in India,etc). There are several critical decisions that must be taken in order to obtain a compromise and optimization between plant performance, cost, and durability. Some of these decisions go through the SF design: proper thermodynamic operational parameters, receiver material selection for high pressures, phase separators and recirculation pumps number and location, pipes distribution to reduce the amount of tubes (reducing possible leaks points and transient time, etc.), etc. Attending to these aspects, the correct design parameters selection and its correct assessment are the main target for designing DSG LF power plants. For this purpose in the recent few years some commercial software tools were developed to simulatesolar thermal power plants, the most focused on LF DSG design are Thermoflex and System Advisor Model (SAM). Once the simulation tool is selected,it is made the study of the proposed SFconfiguration that constitutes the main innovation of this work, and also a comparison with one of the most typical state-of-the-art configuration. The transient analysis must be simulated with high detail level, mainly in the BOP during start up, shut down, stand by, and partial loads are crucial, to obtain the annual plant performance. An innovative SF configurationwas proposed and analyzed to improve plant performance. Finally it was demonstrated thermal inertia and BOP regulation mode are critical points in low sun irradiation day plant behavior, impacting in annual performance depending on power plant location.

The Spanish water ?pressure cooker?: Threading the interplay between resource resilient water governance outcomes by strengthening the robustness of water governance processes.

This paper uses the metaphor of a pressure cooker to highlight how water problems in Spain are highly geographical and sectorial in nature, with some specific hotspots which raise the temperature of the whole water complex system, turning many potentially solvable water problems into ?wicked problems?. The paper discusses the tendency for water governance to be hydrocentric, when often the drivers and in turn the ?solutions? to Spanish water problems lie outside the water sphere. The paper analyzes of the current water governance system by looking at water governance as both a process, and its key attributes like participation, trans- parency, equity and rule of law, as well as an analysis of water governance as an outcome by looking at efficiency and sustainability of water use in Spain. It concludes on the need to have a deeper knowledge on the interactions of water governance as a process and as an outcome and potential synergies and arguing that water governance is an inherently political process which calls for strengthening the capacity of the system by looking at the interactions of these different governance attributes.

Supercritical Steam power cycle for Line-Focus Solar Power Plants

The supercritical Rankine power cycle offers a net improvement in plant efficiency compared with a subcritical Rankine cycle. For fossil power plants the minimum supercritical steam turbine size is about 450MW. A recent study between Sandia National Laboratories and Siemens Energy, Inc., published on March 2013, confirmed the feasibility of adapting the Siemens turbine SST-900 for supercritical steam in concentrated solar power plants, with a live steam conditions 230-260 bar and output range between 140-200 MWe. In this context, this analysis is focused on integrating a line-focus solar field with a supercritical Rankine power cycle. For this purpose two heat transfer fluids were assessed: direct steam generation and molten salt Hitec XL. To isolate solar field from high pressure supercritical water power cycle, an intermediate heat exchanger was installed between linear solar collectors and balance of plant. Due to receiver selective coating temperature limitations, turbine inlet temperature was fixed 550ºC. The design-point conditions were 550ºC and 260 bar at turbine inlet, and 165 MWe Gross power output. Plant performance was assessed at design-point in the supercritical power plant (between 43-45% net plant efficiency depending on balance of plantconfiguration), and in the subcritical plant configuration (~40% net plant efficiency). Regarding the balance of plant configuration, direct reheating was adopted as the optimum solution to avoid any intermediate heat exchanger. One direct reheating stage between high pressure turbine and intermediate pressure turbine is the common practice; however, General Electric ultrasupercritical(350 bar) fossil power plants also considered doubled-reheat applications. In this study were analyzed heat balances with single-reheat, double-reheat and even three reheating stages. In all cases were adopted the proper reheating solar field configurations to limit solar collectors pressure drops. As main conclusion, it was confirmed net plant efficiency improvements in supercritical Rankine line-focus (parabolic or linear Fresnel) solar plant configurations are mainly due to the following two reasons: higher number of feed-water preheaters (up to seven)delivering hotter water at solar field inlet, and two or even three direct reheating stages (550ºC reheating temperature) in high or intermediate pressure turbines. However, the turbine manufacturer should confirm the equipment constrains regarding reheating stages and number of steam extractions to feed-water heaters.

Energetic performance of landfill and digester biogas in a domestic cooker

The energetic performance of landfill biogas (LB) and biodigester biogas (BB) from municipal waste was examined in consumption tests. These tests were performed in situ at a gas generation plant associated with a landfill facility in Madrid (Spain) and following the standard UNE-EN 30-2-1 (1999). The jets of a domestic cooker commonly used for natural gas (NG) or liquefied petroleum gas (LPG) were modified to operate with the biogases produced at the facility. The working pressures best suited to the tested gases, i.e., to avoid flashback and flame lift, and to ensure the stability and correct functioning of the flame during combustion, were determined by trial and error. Both biogases returned optimum energetic performance for the transfer of heat to water in a metallic recipient (as required by the above standard) at a supply pressure of 10 mbar. Domestic cookers are normally supplied with NG at a pressure of 20 mbar, at which pressure the energetic performance of G20 reference gas was higher than that of both biogases (52.84% compared to 38.06% and 49.77% respectively). Data concerning these issues involving also unexplored feedstock are required for the correct conversions of domestic cookers in order to avoid risks of serious personal injuries or property damages.

Optimización del Abonado Nitrogenado en el Melón (Cucumis Melo L.) Tipo Piel de Sapo

Spain is the fifth-largest producer of melon (Cucumis melo L.) and the second exporter in the world. To a national level, Castilla-La Mancha emphasize and, specifically, Ciudad Real, where is cultivated 27% of national area dedicated to this crop and 30% of melon national production. Melon crop is cultivating majority in Ciudad Real and it is mainly located in the Alto Guadiana, where the major aquifers of the region are located, the aquifer 23 or Mancha Occidental and the aquifer 24 or Campo de Montiel, both declared overexploited and vulnerable zones to nitrate pollution from agricultural sources. The problem is exacerbated because in this area, groundwater is the basic resource of supply to populations, and even often the only one. Given the importance of melon in the area, recent research has focused on the irrigation of melon crop. Unfortunately, scant information has been forthcoming on the effect of N fertilizer on melon piel de sapo crop, so it is very important to tackle in a serious study that lead to know the N requirements on the melon crop melon by reducing the risks of contamination by nitrate leaching without affecting productivity and crop quality. In fact, the recommended dose is often subjective and practice is a N overdose. In this situation, the taking of urgent measures to optimize the use of N fertilization is required. To do it, the effect of N in a melon crop, fertirrigated and on plastic mulch, was studied. The treatments consisted in different rates of N supply, considering N fertilizer and N content in irrigation water, so the treatment applied were: 30 (N30), 85 (N85), 112 (N112) and 139 (N139) Kg N ha-1 in 2005; 93 (N93), 243 (N243) and 393 (N393) kg ha-1 in 2006; and 11 (N11), 61 (N61), 95 (N95) and 148 (N148) kg ha-1 in 2007. A randomized complete-block design was used and each treatment was replicated four times. The results showed a significant effect of N on dry biomass and two patterns of growth were observed. On the one hand, a gradual increase in vegetative biomass of the plant, leaves and stem, with increasing N, and on the other hand, an increase of fruit biomass also with increasing N up to a maximum of biomass corresponding to the optimal dose determined in 90 kg ha-1 of N applied, corresponding to 160 kg ha-1 of N available for melon crop, since this optimum dose, the fruit biomass suffers a decline. A significant effect was observed in concentration and N uptake in leaf, steam, fruit and whole plant, increasing in all of them with increasing of N doses. Fast N uptake occurred from 30-35 to 70-80 days after transplanting, coinciding with the fruit development. The N had a clear influence on the melon yield, its components, skin thickness and flesh ratio. The melon yield increased, as the mean fruit weight and number of fruits per m2 with increasing N until achieve an above 95% of the maximum yield when the N applied is 90 kg ha-1 or 160 kg ha-1 of N available. When N exceeds the optimal amount, there is a decline in yield, reducing the mean fruit weight and number of fruits per square meter, and was also observed a decrease in fruit quality by increasing the skin thickness and decrease the flesh ratio, which means an increase in fruit hollowed with excessive N doses. There was a trend for all indexes of N use efficiency (NUE) to decline with increasing N rate. We observed two different behaviours in the calculation result of the NUE; on the one hand, all the efficiency indexes calculated with N applied and N available had an exponential trend, and on the other hand, all the efficiency indexes calculated with N uptake has a linear trend. The linear regression cuts the exponential curve, delimiting a range within which lies the optimum quantity of N. The N leaching as nitrates increased exponentially with the amount of N. The increase of N doses was affected on the N mineralization. There was a negative exponential effect of N available on the mineralization of this element that occurs in the soil during the growing season, calculated from the balances of this element. The study of N leaching for each N rate used, allowed to us to establish several environmental indices related to environmental risk that causes the use of such doses, a simple way for them to be included in the code of Best Management Practices.

A design-phase PSA of anuclear-powered hydrogen plant

A probabilistic safety assessment (PSA) is being developed for a steam-methane reforming hydrogenproduction plant linked to a high-temperature gas-cooled nuclear reactor (HTGR). This work is based on the Japan Atomic Energy Research Institute's (JAERI) High Temperature Engineering Test Reactor (HTTR) prototype in Japan. The objective of this paper is to show how the PSA can be used for improving the design of the coupled plants. A simplified HAZOP study was performed to identify initiating events, based on existing studies. The results of the PSA show that the average frequency of an accident at this complex that could affect the population is 7 × 10−8 year−1 which is divided into the various end states. The dominant sequences are those that result in a methane explosion and occur with a frequency of 6.5 × 10−8 year−1, while the other sequences are much less frequent. The health risk presents itself if there are people in the vicinity who could be affected by the explosion. This analysis also demonstrates that an accident in one of the plants has little effect on the other. This is true given the design base distance between the plants, the fact that the reactor is underground, as well as other safety characteristics of the HTGR.

Full scale test for explosion water barriers in small cross-section galleries

Underground coal mines explosions generally arise from the inflammation of a methane/air mixture. This explosion can also generate a subsequent coal dust explosion. Traditionally such explosions have being fought eliminating one or several of the factors needed by the explosion to take place. Although several preventive measures are taken to prevent explosions, other measures should be considered to reduce the effects or even to extinguish the flame front. Unlike other protection methods that remove one or two of the explosion triangle elements, namely; the ignition source, the oxidizing agent and the fuel, explosion barriers removes all of them: reduces the quantity of coal in suspension, cools the flame front and the steam generated by vaporization removes the oxygen present in the flame. Passive water barriers are autonomous protection systems against explosions that reduce to a satisfactory safety level the effects of methane and/or flammable dust explosions. The barriers are activated by the pressure wave provoked in the explosion destroying the barrier troughs and producing a uniform dispersion of the extinguishing agent throughout the gallery section in quantity enough to extinguish the explosion flame. Full scale tests have been carried out in Polish Barbara experimental mine at GIG Central Mining Institute in order to determine the requirements and the optimal installation conditions of these devices for small sections galleries which are very frequent in the Spanish coal mines. Full scale tests results have been analyzed to understand the explosion timing and development, in order to assess on the use of water barriers in the typical small crosssection Spanish galleries. Several arrangements of water barriers have been designed and tested to verify the effectiveness of the explosion suppression in each case. The results obtained demonstrate the efficiency of the water barriers in stopping the flame front even with smaller amounts of water than those established by the European standard. According to the tests realized, water barriers activation times are between 0.52 s and 0.78 s and the flame propagation speed are between 75 m/s and 80 m/s. The maximum pressures (Pmax) obtained in the full scale tests have varied between 0.2 bar and 1.8 bar. Passive barriers protect effectively against the spread of the flame but cannot be used as a safeguard of the gallery between the ignition source and the first row of water troughs or bags, or even after them, as the pressure could remain high after them even if the flame front has been extinguished.

Viability study of sailing propulsion combined with a conventional system

For many years now, sails have been used as a propulsion system. At present, they are restricted to recreational/sport crafts since the appearance of the first steam vessels in the beginning of the 19 th century. But in the last years, due to the increase of fuel price and the pollution of the environment, it is being studied the possibility to introduce again the sail as a propulsive method combined with other conventional systems. In this paper, it is studied the viability of using a sail as a propellant with other conventional systems of propulsion. After considering the concept of apparent wind, the range of use of this complementary propulsion is presented. The calculation methodology, the numerical simulations and the wind inputs from a specific route are also included.

Desarrollo de un modelo para la caracterización termoeconómica de ciclos combinados de turbinas de gas y de vapor en condiciones de carga variable

En la actualidad, el interés por las plantas de potencia de ciclo combinado de gas y vapor ha experimentado un notable aumento debido a su alto rendimiento, bajo coste de generación y rápida construcción. El objetivo fundamental de la tesis es profundizar en el conocimiento de esta tecnología, insuficientemente conocida hasta el momento debido al gran número de grados de libertad que existen en el diseño de este tipo de instalaciones. El estudio se realizó en varias fases. La primera consistió en analizar y estudiar las distintas tecnologías que se pueden emplear en este tipo de centrales, algunas muy recientes o en fase de investigación, como las turbinas de gas de geometría variable, las turbinas de gas refrigeradas con agua o vapor del ciclo de vapor o las calderas de paso único que trabajan con agua en condiciones supercríticas. Posteriormente se elaboraron los modelos matemáticos que permiten la simulación termodinámica de cada uno de los componentes que integran las plantas, tanto en el punto de diseño como a cargas parciales. Al mismo tiempo, se desarrolló una metodología novedosa que permite resolver el sistema de ecuaciones que resulta de la simulación de cualquier configuración posible de ciclo combinado. De esa forma se puede conocer el comportamiento de cualquier planta en cualquier punto de funcionamiento. Por último se desarrolló un modelo de atribución de costes para este tipo de centrales. Con dicho modelo, los estudios se pueden realizar no sólo desde un punto de vista termodinámico sino también termoeconómico, con lo que se pueden encontrar soluciones de compromiso entre rendimiento y coste, asignar costes de producción, determinar curvas de oferta, beneficios económicos de la planta y delimitar el rango de potencias donde la planta es rentable. El programa informático, desarrollado en paralelo con los modelos de simulación, se ha empleado para obtener resultados de forma intensiva. El estudio de los resultados permite profundizar ampliamente en el conocimiento de la tecnología y, así, desarrollar una metodología de diseño de este tipo de plantas bajo un criterio termoeconómico. ABSTRACT The growing energy demand and the need of shrinking costs have led to the design of high efficiency and quick installation power plants. The success of combined cycle gas turbine power plants lies on their high efficiency, low cost and short construction lead time. The main objective of the work is to study in detail this technology, which is not thoroughly known owing to the great number of degrees of freedom that exist in the design of this kind of power plants. The study is divided into three parts. Firstly, the different technologies and components that could be used in any configuration of a combined cycle gas turbine power plant are studied. Some of them could be of recent technology, such as the variable inlet guide vane compressors, the H-technology for gas turbine cooling or the once-through heat recovery steam generators, used with water at supercritical conditions. Secondly, a mathematical model has been developed to simulate at full and part load the components of the power plant. At the same time, a new methodology is proposed in order to solve the equation system resulting for any possible power plant configuration. Therefore, any combined cycle gas turbine could be simulated at any part load condition. Finally a themoeconomic model is proposed. This model allows studying the power plant not only from a thermodynamic point of view but also from a thermoeconomic one. Likewise, it allows determining the generating costs or the cash flow, thus achieving a trade off between efficiency and cost. Likewise, the model calculates the part load range where the power plant is profitable. Once the thermodynamic and thermoeconomic models are developed, they are intensively used in order to gain knowledge in the combined cycle gas turbine technology and, in this way, to propose a methodology aimed at the design of this kind of power plants from a thermoeconomic point of view.

El injerto en pepino corto tipo español (Cucumis sativus L.) recomencaciones para su empleo en la zona central española

El injerto en hortalizas es uno de los temas de más actualidad en el panorama hortícola, no solo español, sino occidental, y recalcamos occidental, pues en muchos países que no corresponden a ese ámbito, sobre todo asiáticos: Japón, Corea, China, Filipinas, etc., esta es una técnica que cuenta con una gran difusión desde hace décadas, siendo, por ejemplo en Japón, la mayoría de sus cultivos de cucurbitáceas y solanáceas realizados con planta injertada. A finales de los noventa quedó claro que el empleo de bromuro de metilo tenía una fecha de caducidad y que las zonas que tenían una fuerte dependencia de este desinfectante de suelo debían de buscar alternativas a un plazo lo más corto posible, con un punto añadido sobre etapas anteriores, debían ser alternativas lo más respetuosas posible con el medio ambiente y que no incrementaran, de forma importante, los costes de producción. En la zona centro y concretamente en los invernaderos de la Comunidad de Madrid y zonas cercanas de Toledo y Guadalajara el pepino era y es el cultivo predominante, los horticultores empleaban el bromuro de metilo de forma sistemática para desinfectar sus suelos y la desaparición de este producto les planteaba una gran incertidumbre, lo que llevó a que desde diferentes instancias se buscaran diferentes alternativas. Tras analizar las posibilidades que se podían implementar y conocido el buen resultado que había dado el injerto en sandía en Almería, se decidió acometer los trabajos que conforman esta Tesis Doctoral, planteando en la zona, diferentes ensayos con la idea de conocer, si el injerto en pepino, con los cultivares empleados habitualmente, podía ser una alternativa real para los horticultores, tanto de Madrid, como los de las zonas cercanas de Toledo y Guadalajara. Se pretendía conocer sobre todo las repercusiones agronómicas y si esta técnica podría emplearse en solitario o era necesario complementarla con otras alternativas: desinfectantes químicos, solarización, biofumigación e incluso desinfección con vapor de agua. Los ensayos fueron realizados de forma secuencial entre el año 1999 y el 2011, comprobándose en primer lugar que el empleo de portainjertos híbridos de calabaza era posible con los cultivares de pepino corto tipo español, mayoritariamente empleados en los últimos años del siglo XX y primeros del XXI, fundamentalmente: Serena. Tras los primeros ensayos, Shintoza parecía el portainjerto híbrido de calabaza (Cucurbita maxima x C. moschata) con mejores perspectivas de empleo, pues presentaba la ventaja adicional de ser bien conocido por los semilleros que producen planta injertada al ser, en esos momentos, el portainjerto más empleado en sandía, lo que garantizaba por su lado, su empleo en pepino, y que los horticultores pudiesen disponer de planta injertada. Más adelante los trabajos se encaminaron hacia la determinación de la densidad y tipo de poda más adecuado para la planta injertada, realizándose múltiples ensayos en esta dirección, que culminaron con la conclusión de que el extravigor que los portainjertos conferían a las plantas permitía conducir estas a dos o más brazos (se suelen emplear dos, por mejor adaptación a los trabajos de manejo de la planta por parte de los agricultores), con lo que se podría disminuir la densidad de planta y por tanto ahorrar en este capítulo, cosa que preocupaba y preocupa a los agricultores. Se llegó a determinar que es posible reducir la densidad de plantación en alrededor de un 25%, estando la densidad de brazos más adecuada entre 3 y 3.5 br•m-2. Tras las primeras decisiones tomadas sobre el portainjerto y la densidad más adecuada, se continuó con el estudio de adaptación de estas propuestas a los nuevos cultivares que las empresas de semillas iban proponiendo y los agricultores adoptando. Estas acciones se complementaron con la introducción de nuevos portainjertos susceptibles de sustituir a Shintoza o rotar con él para cambiar de sistema radicular, lo que es conveniente cuando se emplean, como es el caso, portainjertos que no son resistentes a nematodos, principalmente de la especie Meloidogyne incognita, el mayor problema en la zona, debido al suelo. Cultivares como Trópico, en un primer momento, y Urano y Motril más recientemente, se adaptaron muy bien a esta técnica. Entre los portainjertos que mostraron buena adaptación a la técnica de injerto y suficientemente buena compatibilidad con la mayoría de los cultivares ensayados destacan: RS-841, Strongtosa y Camel. Azman también mostró un comportamiento relevante, pero este portainjerto no podrá ser empleado, al ser recientemente retirado del mercado por la empresa que lo obtuvo y comercializó Aunque no era el objetivo principal de esta Tesis Doctoral, se ha comprobado que puede ser interesante combinar el empleo del injerto con otras técnicas alternativas al bromuro de metilo para superar los problemas debidos a enfermedades del suelo o nematodos, pero debe seguirse trabajando pues este es un tema en continua evolución, tanto si se trata de desinfectantes, a la mayoría de los cuales les está siendo retirado el permiso para su comercialización, como de otros métodos como la biofumigación o el empleo de vapor de agua. Queda muy claro que el injerto puede considerarse entre los métodos respetuosos con el medio ambiente, si no el que más, en lo que alternativas al bromuro de metilo se refiere. También en otro momento, se comprobó que con plantas injertadas es posible reducir el aporte de nutrientes, sobre todo nitrógeno, lo que además de un ahorro supone una mejora más desde el punto de vista medioambiental. En definitiva, queda demostrado que es factible el empleo del injerto en pepino corto tipo español, que las selecciones de los híbridos entre Cucurbita maxima y C. moschata que habitualmente se están empleando en sandía son también de aplicación en estos pepinos y que su empleo puede llevarnos a producciones suficientemente remuneradoras, alargándose en muchos casos el ciclo y no modificando, de forma apreciable, la calidad. Queda también demostrado que aunque los portainjertos no sean resistentes a nematodos, su extravigor les hace desarrollarse, desde el punto de vista productivo, suficientemente, llegando por tanto, a “convivir” con ese problema. Al no ser resistentes los portainjertos, y permanecer e incluso agravarse el problema de nematodos es conveniente poder contar con diferentes portainjertos que nos permitan rotar entre ellos y utilizar diferentes sistemas radiculares que harán menos fácil el parasitismo de los nematodos, como recomiendan los nematólogos que se haga. ABSTRACT Vegetable grafting is one of the most current practices in horticulture, not only in Spain, but also in other Western and Asian countries, such as Japan, South Korea, China, the Philippines, etc. This is a decades-old, widespread technique: In fact, most cucurbit and solanaceous crops in Japan and Korea are grafted. At the end of the 1990s, it was clear that methyl bromide had an expiry date. Consequently, the areas strongly dependant on this soil disinfectant had to look for alternatives as quickly as possible. Besides, these had to be as environmentally friendly as possible and should not increase production costs significantly. The cucumber has been and still is the most important crop in greenhouses of the Comunidad de Madrid and in areas near Toledo and Guadalajara. Cucumber growers used methyl bromide systematically to disinfect the soil. The banning of this chemical product brought about uncertainty, which encouraged the search for different alternatives. After analyzing the different possibilities and taking into account the good results of watermelon grafting in Almería, it was decided to carry out the works that make up this doctoral thesis. Different trials were made in order to know if the cultivars used in cucumber grafting might be a real alternative for farmers, not only in Madrid, but also in the areas near Toledo and Guadalajara. The main aim was to assess the agronomic repercussions and whether that technique could be used alone, or if other complementary alternatives, such as chemical disinfectants, solarisation, biofumigation, or even steam disinfection, were necessary. Trials were carried out sequentially from 1999 to 2011. It was observed that the use of pumpkin hybrid rootstocks could be applied to cultivars of Spanish short cucumbers, mainly grown in the late 20th and early 21st centuries eg Serena. After the early trials, Shintoza (Cucurbita maxima x C. moschata), a pumpkin hybrid rootstock, seemed to be the best option, as it had the additional advantage of being well known by nurseries growing grafting plants. Bearing this in mind, Shintoza was then the hybrid rootstock to be used in cucumbers and consequently growers could have grafted plants at their disposal. Later on, research was focused on density and the most adequate type of pruning, by carrying out several trials. These experiments showed that, the extra vigour the rootstocks gave to the plants, allowed them to have two or three stems, (normally nurserymen use two, as it is easier for them to manage the plants). These findings would lead to the lessening the density of the plant and thus reduce costs, something which worried and still worries farmers. It was stated that it would be possible to reduce the density of the plants by about 25%, the optimum density of the stems ranging from 3 to 3.5 stem-m-2. Once decisions were taken both on the rootstock and the appropriate density, we went on to study how to apply these proposals to the new cultivars which the seed companies were proposing and the farmers were applying. These measures were complemented with the introduction of new rootstocks capable of replacing Shintoza, or rotating with it in order to change the root system. This is particularly necessary when rootstocks, non-resistant to nematodes, mainly of the species Meloidogyne incognita, are used. This is the main problem due to the soil of that area. Cultivars such as Trópico, at first, and Urano and Motril, more recently, adapted quite well to this technique. Among the rootstocks which adapted well to grafting and which were compatible with most tested cultivars, were, in particular, RS-841 Strongtosa and Camel. The behaviour of Azman was worth studying, but this rootstock was removed from the market by the company which had bought and commercialized it. Although not the main purpose of the research, it was observed that combining grafting with other alternatives to methyl bromide in order to overcome problems due to soil diseases or nematodes may be worthwhile. However, further research is needed, as this topic is in constant evolution, not only when we come to disinfectants, most of which are being affected by the removal of the permit for commercialization, but also when we refer to other techniques such as biofumigation or the use of steam. Results also showed that grafted plants may reduce the amount of fertilizers, particularly nitrogen, used: This means both saving money and the protection of the environment. We may conclude by saying that grafting Spanish short cucumbers is feasible, that the selections of the hybrids between Cucurbita maxima and C. moschata, habitually used in watermelon grafting, can also be applied to these cucumbers. It can also be concluded that the use of these grafting techniques may lead to profitable yields, by lengthening the growing cycle in many cases and by maintaining the quality to a large extent. Although these rootstocks are not resistant to nematodes, the results showed that their extra vigour enables them to develop in terms of production, and thus they cope with this problem. Since these rootstocks are not resistant to nematodes and the problem with these nematodes may even worsen, it is recommended that different types of rootstocks should be available to enable both the rotation and the use of different root systems, which will encourage the parasitism of nematodes.