Correlation Between Processing Conditions, Microstructure and Mechanical Behavior in Regenerated Silkworm Silk Fibers

Regenerated silkworm fibers spun through a wet-spinning process followed by an immersion postspinning drawing step show a work to fracture comparable with that of natural silkworm silk fibers in a wide range of spinning conditions. The mechanical behavior and microstructure of these high performance fibers have been characterized, and compared with those fibers produced through conventional spinning conditions. The comparison reveals that both sets of fibers share a common semicrystalline microstructure, but significant differences are apparent in the amorphous region. Besides, high performance fibers show a ground state and the possibility of tuning their tensile behavior. These properties are characteristic of spider silk and not of natural silkworm silk, despite both regenerated and natural silkworm silk share a common composition different from that of spider silk.

Arquitectura óptima: Cuatro medios prácticos para optimizar proyectos de arquitectura

La investigación trata de mostrar cuatro acciones habitualmente empleadas al proyectar arquitectura. La tesis narra el discurso que construyen cuatro acciones como mecanismos optimizadores, fundamentales, activos y necesarios cuando creamos nuevos proyectos. En este trabajo se estudian en profundidad cuatro acciones optimizadoras a través de numerosos casos de estudio. Se estudia también la presencia de estas acciones en otros campos creativos, como la biología, el arte, la literatura, la filosofía, la matemática o la psicología de la creatividad. Se busca qué tienen en común estas cuatro acciones y se indaga sobre la posible narración que construyen entre ellas. La mayor parte de los textos que constituyen este trabajo se escriben en un formato próximo al del ensayo, empleando tiempos verbales presentes evitando los tiempos verbales pretéritos o imperfectos para potenciar la acción a través el estilo narrativo. La investigación se ha realizado a partir de fuentes bibliográficas existentes en numerosas bibliotecas. Se han llevado a cabo estudios de campo realizados a través de entrevistas personales a interlocutores expertos, no sólo de teoría arquitectónica sino también de prácticas constructivas, así como visitas a lugares íntimamente relacionados con el tema de investigación. Se ha completado el estudio de casos con ejercicios prácticos realizados por el autor de esta tesis, para profundizar con la propia investigación por empatía con los autores estudiados. La investigación bibliográfica principal se ha desarrollado en las bibliotecas de la Universidad Politécnica de Madrid, de la Universidad de Alicante, de la Universidad Autónoma de Madrid, de la Universidad Europea de Madrid, de la Universidad Camilo José Cela, de la Universidad Complutense de Madrid, de la Columbia University, de la Harvard University, de la Delft University, de Heidelberg University, de la Biblioteca Central de Madrid y de la Regional de Murcia, así como de la del COAMU. También se ha utilizado recursos bibliográficos propios. La metodología utilizada muestra desde diferentes perspectivas el problema de las acciones optimizadoras, desde obras artísticas, pasando por ejemplos de arquitectura construida hasta ejercicios puramente intelectuales. La acumulación ha sido el método de obtención de conocimiento de esta tesis. Se han acumulado conocimientos y posteriormente se ha profundizado, reflexionando sobre los datos que se han ido obteniendo. Al profundizar se enlazan unas pruebas con otras, hilando y ensamblándolas en un discurso que hace continuo y coherente la aparición de cada caso estudiado. Estas entidades probatorias son acciones que han sido aplicadas frecuentemente por distintas generaciones de autores que proyectan utilizando alguna de estas cuatro acciones. Partimos de una extensa bibliografía general y de otra específica. A través de citas e imágenes se muestra el repertorio de objetos y textos estudiados. Los casos de estudio seleccionados exponen los efectos que produce cada acción en el ejercicio del proyectar. Se ha estudiado la necesidad de cada acción en todas y cada una de las partes del ciclo creativo del proyecto, tanto en prácticas imaginadas como en construidas, de los autores que proyectan. Se citan y se interpretan las descripciones de biólogos, sociólogos, antropólogos, psicólogos, escritores, artistas, arquitectos, matemáticos, ingenieros, físicos, médicos y filósofos en los cuales estas acciones se encuentran conscientemente incorporadas en su procedimiento de proyectar y de pensar. Por último, hemos obtenido unos resultados adecuados a la metodología empleada y a los objetivos planteados gracias a la acumulación y clasificación de pruebas. Los resultados se exponen a modo de discursos conclusivos con un intencionado carácter abierto que despliega nuevas posibles nuevas vías de investigación entorno a los temas estudiados. ABSTRACT. The research seeks to show four commonly used actions in designing architecture. Thesis recounts the speech that built four actions like optimizer, fundamental, active and necessary mechanisms when we create new projects. In this work it studies in depth four optimizer actions through numerous case studies. Also, it considers the presence of these actions in other creative fields, such as biology, art, literature, philosophy, mathematics or psychology of creativity. It is intended what these four actions have in common and it explores the possible narrative constructed among them. Most of the texts that constitute this work are written in a format close to the essay, using present tenses avoiding past or imperfect tenses of enhancing the action through the narrative style. Research has been done from literature sources available in numerous libraries. Field studies have been carried out through personal interviews with expert speakers, not just of architectonic theory but also from constructive practices, as well as visits to sites closely related to the research topic. case studies with practical exercises conducted by the author of this thesis has been completed, to deepen with the own research by empathy with the studied authors. Main bibliographical investigation has been developed in the libraries of UPM, UA, UAM, UEM, the CJC, the UCM, Columbia University, Harvard University Delft University, Heidelberg University, Madrid Central Library, Regional Murcia Library and COAMU Library. Also it has been used own bibliographical resources. Methodology shows from different perspectives the problem of optimizers actions, from art, passing through examples of architecture built up to puré intellectual exercise. Accumulation has been the method of obtaining knowledge of this thesis. it has been accumulated knowledge and later it has been deepened, reflecting on the data that have been obtained. By deepening tests are linked with other, spinning and locking into a discourse that makes continuous and consistent the development of each case study. These evidentiary entities are actions that have been frequently applied by different generations of authors who project using some of these four stocks. We leave from an extensive general bibliography and another specific one. Through quotes and pictures it shows the repertoire of objects and texts studied. The selected study cases set out the effects that each action produces in the exercise of projecting. It has studied the need of each action in every parts of creative cycle of the project, both imagined as constructed practices, by the authors who project. It is quoted and interpreted the descriptions of biologists, sociologists, anthropologists, psychologists, writers, artists, architects, mathematicians, engineers, physicists, physicians and philosophers in which these actions are consciously incorporated into his projecting and thinking procedure. Finally, we have obtained adequate results to the used methodology and to the stated objectives through the accumulation and classification of evidence. The results are presented as conclusive speeches with an intentional open character that unfolds new possible research routes around the studied topics.

Sequential origin in the high performance properties of spider dragline silk

Major ampullate (MA) dragline silk supports spider orb webs, combining strength and extensibility in the toughest biomaterial. MA silk evolved ~376 MYA and identifying how evolutionary changes in proteins influenced silk mechanics is crucial for biomimetics, but is hindered by high spinning plasticity. We use supercontraction to remove that variation and characterize MA silk across the spider phylogeny. We show that mechanical performance is conserved within, but divergent among, major lineages, evolving in correlation with discrete changes in proteins. Early MA silk tensile strength improved rapidly with the origin of GGX amino acid motifs and increased repetitiveness. Tensile strength then maximized in basal entelegyne spiders, ~230 MYA. Toughness subsequently improved through increased extensibility within orb spiders, coupled with the origin of a novel protein (MaSp2). Key changes in MA silk proteins therefore correlate with the sequential evolution high performance orb spider silk and could aid design of biomimetic fibers.

Minor ampullate silks from Nephila and Argiope spiders: tensile properties and microstructural characterization

The mechanical behavior and microstructure of minor ampullate gland silk (miS) of two orb-web spinning species, Argiope trifasciata and Nephila inaurata, were extensively characterized, enabling detailed comparison with other silks. The similarities and differences exhibited by miS when compared with the intensively studied major ampullate gland silk (MAS) and silkworm (Bombyx mori) silk offer a genuine opportunity for testing some of the hypotheses proposed to correlate microstructure and tensile properties in silk. In this work, we show that miSs of different species show similar properties, even when fibers spun by spiders that diverged over 100 million years are compared. The tensile properties of miS are comparable to those of MAS when tested in air, significantly in terms of work to fracture, but differ considerably when tested in water. In particular, miS does not show a supercontraction effect and an associated ground state. In this regard, the behavior of miS in water is similar to that of B. mori silk, and it is shown that the initial elastic modulus of both fibers can be explained using a common model. Intriguingly, the microstructural parameters measured in miS are comparable to those of MAS and considerably different from those found in B. mori. This fact suggests that some critical microstructural information is still missing in our description of silks, and our results suggest that the hydrophilicity of the lateral groups or the large scale organization of the sequences might be routes worth exploring.

Electrodynamic tether at Jupiter II:Fast moon tour after capture

An electrodynamic bare-tether mission to Jupiter,following the capture of a spacecraft (SC) into an equatorial highly elliptical orbit with perijove at about 1.3 times the Jovian radius, is discussed. Repeated applications of the propellantless Lorentz drag on a spinning tether, at the perijove vicinity, can progressively lower the apojove at constant perijove, for a tour of Galilean moons. Electrical energy is generated and stored as the SC moves from an orbit at 1 : 1 resonance with a moon, down to resonance with the next moon; switching tether current off, stored power is then used as the SC makes a number of flybys of each moon. Radiation dose is calculated throughout the mission,during capture, flybys and moves between moons. The tour mission is limited by both power needs and accumulated dose. The three-stage apojove lowering down to Ganymede, Io, and Europa resonances would total less than 14 weeks, while 4 Ganymede, 20 Europa, and 16 Io flybys would add up to 18 weeks, with the entire mission taking just over seven months and the accumulated radiation dose keeping under 3 Mrad (Si) at 10-mm Al shield thickness.

A proposed two-stage two-tether scientific mission at Jupiter

A two-stage mission to place a spacecraft (SC) below the Jovian radiation belts, using a spinning bare tether with plasma contactors at both ends to provide propulsion and power,is proposed. Capture by Lorentz drag on the tether, at the periapsis of a barely hyperbolic equatorial orbit, is followed by a sequence of orbits at near-constant periapsis, drag finally bringing the SC down to a circular orbit below the halo ring. Although increasing both tether heating and bowing, retrograde motion can substantially reduce accumulated dose as compared with prograde motion, at equal tether-to-SC mass ratio. In the second stage,the tether is cut to a segment one order of magnitude smaller, with a single plasma contactor, making the SC to slowly spiral inward over severalmonths while generating large onboard power, which would allow multiple scientific applications, including in situ study of Jovian grains, auroral sounding of upper atmosphere, and space- and time-resolved observations of surface and subsurface.

Electrodynamic tether at Jupiter 2. Tour missions after capture

Three separate scenarios of an electrodynamic tether mission at Jupiter following capture of a spacecraft (SC) into an equatorial, highly elliptical orbit around the planet, with perijove at about 1.5 times the Jovian radius, are discussed. Repeated application of Lorentz drag on the spinning tether, at the perijove vicinity, can progressively lower the apojove. One mission involves the tethered-SC rapidly and frequently visiting Galilean moons; elliptical orbits with apojove down at the Ganymede, Europa, and Io orbits are in 2:5, 4:9, and 1:2 resonances with the respective moons. About 20 slow flybys of Io would take place before the accumulated radiation dose exceeds 3 Mrad (Si) at 10 mm Al shield thickness, with a total duration of 5 months after capture (4 months for lowering the apojove to Io and one month for the flybys). The respective number of flybys for Ganymede would be 10 with a total duration of about 9 months. An alternative mission would have the SC acquire a low circular orbit around Jupiter, below the radiation belts, and manoeuvre to get an optimal altitude, with no major radiation effects, in less than 5 months after capture. In a third mission, repeated thrusting at the apojove vicinity, once down at the Io torus, would raise the perijove itself to the torus to acquire a low circular orbit around Io in about 4 months, for a total of 8 months after capture; this corresponds, however, to over 100 apojove passes with an accumulated dose, of about 8.5 Mrad (Si), that poses a critical issue.

Jupiter power generation with electrodynamic tethers at constant orbital energy

An electrodynamic tether system for power generation at Jupiter is presented that allows extracting energy from Jupiter's corotating plasmasphere while leaving the system orbital energy unaltered to first order. The spacecraft is placed in a polar orbit with the tether spinning in the orbital plane so that the resulting Lorentz force, neglecting Jupiter's magnetic dipole tilt, is orthogonal to the instantaneous velocity vector and orbital radius, hence affecting orbital inclination rather than orbital energy. In addition, the electrodynamic tether subsystem, which consists of two radial tether arms deployed from the main central spacecraft, is designed in such a way as to extract maximum power while keeping the resulting Lorentz torque constantly null. The power-generation performance of the system and the effect on the orbit inclination is evaluated analytically for different orbital conditions and verified numerically. Finally, a thruster-based inclination-compensation maneuver at apoapsis is added, resulting in an efficient scheme to extract energy from the plasmasphere of the planet with minimum propellant consumption and no inclination change. A tradeoff analysis is conducted showing that, depending on tether size and orbit characteristics, the system performance can be considerably higher than conventional power-generation methods.

A water footprint assessment of a pair of jeans: the influence of agricultural policies on the sustainability of consumer products.

This study reports the results of a water footprint (WF) assessment of five types of textiles commonly used for the production of jeans, including two different fibres (cotton and Lyocell fibre) and five corresponding production methods for spinning, dyeing and weaving. The results show that the fibre production is the stage with the highest water consumption, being cotton production particularly relevant. Therefore, the study pays particular attention to the water footprint of cotton production and analyses the effects of external factors influencing the water footprint of a product, in this case, the incentives provided by the EU Common Agricultural Policy (CAP), and the relevance of agricultural practices to the water footprint of a product is emphasised. An extensification of the crop production led to higher WF per unit, but a lower overall pressure on the basins water resources. This study performs a sustainability assessment of the estimated cotton WFs with the water scarcity index, as proposed by Hoekstra et al. (2011), and shows their variations in different years as a result of different water consumption by crops in the rest of the river basin. In our case, we applied the assessment to the Guadalquivir, Guadalete and Barbate river basins, three semi-arid rivers in South Spain. Because they are found to be relevant, the available water stored in dams and the outflow are also incorporated as reference points for the sustainability assessment. The study concludes that, in the case of Spanish cotton production, the situation of the basin and the policy impact are more relevant for the status of the basin s water resources than the actual WF of cotton production. Therefore, strategies aimed at reducing the impact of the water footprint of a product need to analyse both the WF along the value chain and within the local context.

Improving the management of water and nitrogen resources in cropping systems by using simulation models

Los modelos de simulación de cultivos permiten analizar varias combinaciones de laboreo-rotación y explorar escenarios de manejo. El modelo DSSAT fue evaluado bajo condiciones de secano en un experimento de campo de 16 años en la semiárida España central. Se evaluó el efecto del sistema de laboreo y las rotaciones basadas en cereales de invierno, en el rendimiento del cultivo y la calidad del suelo. Los modelos CERES y CROPGRO se utilizaron para simular el crecimiento y rendimiento del cultivo, mientras que el modelo DSSAT CENTURY se utilizó en las simulaciones de SOC y SN. Tanto las observaciones de campo como las simulaciones con CERES-Barley, mostraron que el rendimiento en grano de la cebada era mas bajo para el cereal continuo (BB) que para las rotaciones de veza (VB) y barbecho (FB) en ambos sistemas de laboreo. El modelo predijo más nitrógeno disponible en el laboreo convencional (CT) que en el no laboreo (NT) conduciendo a un mayor rendimiento en el CT. El SOC y el SN en la capa superficial del suelo, fueron mayores en NT que en CT, y disminuyeron con la profundidad en los valores tanto observados como simulados. Las mejores combinaciones para las condiciones de secano estudiadas fueron CT-VB y CT-FB, pero CT presentó menor contenido en SN y SOC que NT. El efecto beneficioso del NT en SOC y SN bajo condiciones Mediterráneas semiáridas puede ser identificado por observaciones de campo y por simulaciones de modelos de cultivos. La simulación del balance de agua en sistemas de cultivo es una herramienta útil para estudiar como el agua puede ser utilizado eficientemente. La comparación del balance de agua de DSSAT , con una simple aproximación “tipping bucket”, con el modelo WAVE más mecanicista, el cual integra la ecuación de Richard , es un potente método para valorar el funcionamiento del modelo. Los parámetros de suelo fueron calibrados usando el método de optimización global Simulated Annealing (SA). Un lisímetro continuo de pesada en suelo desnudo suministró los valores observados de drenaje y evapotranspiración (ET) mientras que el contenido de agua en el suelo (SW) fue suministrado por sensores de capacitancia. Ambos modelos funcionaron bien después de la optimización de los parámetros de suelo con SA, simulando el balance de agua en el suelo para el período de calibración. Para el período de validación, los modelos optimizados predijeron bien el contenido de agua en el suelo y la evaporación del suelo a lo largo del tiempo. Sin embargo, el drenaje fue predicho mejor con WAVE que con DSSAT, el cual presentó mayores errores en los valores acumulados. Esto podría ser debido a la naturaleza mecanicista de WAVE frente a la naturaleza más funcional de DSSAT. Los buenos resultados de WAVE indican que, después de la calibración, este puede ser utilizado como "benchmark" para otros modelos para periodos en los que no haya medidas de campo del drenaje. El funcionamiento de DSSAT-CENTURY en la simulación de SOC y N depende fuertemente del proceso de inicialización. Se propuso como método alternativo (Met.2) la inicialización de las fracciones de SOC a partir de medidas de mineralización aparente del suelo (Napmin). El Met.2 se comparó con el método de inicialización de Basso et al. (2011) (Met.1), aplicando ambos métodos a un experimento de campo de 4 años en un área en regadío de España central. Nmin y Napmin fueron sobreestimados con el Met.1, ya que la fracción estable obtenida (SOC3) en las capas superficiales del suelo fue más baja que con Met.2. El N lixiviado simulado fue similar en los dos métodos, con buenos resultados en los tratamientos de barbecho y cebada. El Met.1 subestimó el SOC en la capa superficial del suelo cuando se comparó con una serie observada de 12 años. El crecimiento y rendimiento del cultivo fueron adecuadamente simulados con ambos métodos, pero el N en la parte aérea de la planta y en el grano fueron sobreestimados con el Met.1. Los resultados variaron significativamente con las fracciones iniciales de SOC, resaltando la importancia del método de inicialización. El Met.2 ofrece una alternativa para la inicialización del modelo CENTURY, mejorando la simulación de procesos de N en el suelo. La continua emergencia de nuevas variedades de híbridos modernos de maíz limita la aplicación de modelos de simulación de cultivos, ya que estos nuevos híbridos necesitan ser calibrados en el campo para ser adecuados para su uso en los modelos. El desarrollo de relaciones basadas en la duración del ciclo, simplificaría los requerimientos de calibración facilitando la rápida incorporación de nuevos cultivares en DSSAT. Seis híbridos de maiz (FAO 300 hasta FAO 700) fueron cultivados en un experimento de campo de dos años en un área semiárida de regadío en España central. Los coeficientes genéticos fueron obtenidos secuencialmente, comenzando con los parámetros de desarrollo fenológico (P1, P2, P5 and PHINT), seguido de los parámetros de crecimiento del cultivo (G2 and G3). Se continuó el procedimiento hasta que la salida de las simulaciones estuvo en concordancia con las observaciones fenológicas de campo. Después de la calibración, los parámetros simulados se ajustaron bien a los parámetros observados, con bajos RMSE en todos los casos. Los P1 y P5 calibrados, incrementaron con la duración del ciclo. P1 fue una función lineal del tiempo térmico (TT) desde emergencia hasta floración y P5 estuvo linealmente relacionada con el TT desde floración a madurez. No hubo diferencias significativas en PHINT entre híbridos de FAO-500 a 700 , ya que tuvieron un número de hojas similar. Como los coeficientes fenológicos estuvieron directamente relacionados con la duración del ciclo, sería posible desarrollar rangos y correlaciones que permitan estimar dichos coeficientes a partir de la clasificación del ciclo. ABSTRACT Crop simulation models allow analyzing various tillage-rotation combinations and exploring management scenarios. DSSAT model was tested under rainfed conditions in a 16-year field experiment in semiarid central Spain. The effect of tillage system and winter cereal-based rotations on the crop yield and soil quality was evaluated. The CERES and CROPGRO models were used to simulate crop growth and yield, while the DSSAT CENTURY was used in the SOC and SN simulations. Both field observations and CERES-Barley simulations, showed that barley grain yield was lower for continuous cereal (BB) than for vetch (VB) and fallow (FB) rotations for both tillage systems. The model predicted higher nitrogen availability in the conventional tillage (CT) than in the no tillage (NT) leading to a higher yield in the CT. The SOC and SN in the top layer, were higher in NT than in CT, and decreased with depth in both simulated and observed values. The best combinations for the dry land conditions studied were CT-VB and CT-FB, but CT presented lower SN and SOC content than NT. The beneficial effect of NT on SOC and SN under semiarid Mediterranean conditions can be identified by field observations and by crop model simulations. The simulation of the water balance in cropping systems is a useful tool to study how water can be used efficiently. The comparison of DSSAT soil water balance, with a simpler “tipping bucket” approach, with the more mechanistic WAVE model, which integrates Richard’s equation, is a powerful method to assess model performance. The soil parameters were calibrated by using the Simulated Annealing (SA) global optimizing method. A continuous weighing lysimeter in a bare fallow provided the observed values of drainage and evapotranspiration (ET) while soil water content (SW) was supplied by capacitance sensors. Both models performed well after optimizing soil parameters with SA, simulating the soil water balance components for the calibrated period. For the validation period, the optimized models predicted well soil water content and soil evaporation over time. However, drainage was predicted better by WAVE than by DSSAT, which presented larger errors in the cumulative values. That could be due to the mechanistic nature of WAVE against the more functional nature of DSSAT. The good results from WAVE indicate that, after calibration, it could be used as benchmark for other models for periods when no drainage field measurements are available. The performance of DSSAT-CENTURY when simulating SOC and N strongly depends on the initialization process. Initialization of the SOC pools from apparent soil N mineralization (Napmin) measurements was proposed as alternative method (Met.2). Method 2 was compared to the Basso et al. (2011) initialization method (Met.1), by applying both methods to a 4-year field experiment in a irrigated area of central Spain. Nmin and Napmin were overestimated by Met.1, since the obtained stable pool (SOC3) in the upper layers was lower than from Met.2. Simulated N leaching was similar for both methods, with good results in fallow and barley treatments. Method 1 underestimated topsoil SOC when compared with a 12-year observed serial. Crop growth and yield were properly simulated by both methods, but N in shoots and grain were overestimated by Met.1. Results varied significantly with the initial SOC pools, highlighting the importance of the initialization procedure. Method 2 offers an alternative to initialize the CENTURY model, enhancing the simulation of soil N processes. The continuous emergence of new varieties of modern maize hybrids limits the application of crop simulation models, since these new hybrids should be calibrated in the field to be suitable for model use. The development of relationships based on the cycle duration, would simplify the calibration requirements facilitating the rapid incorporation of new cultivars into DSSAT. Six maize hybrids (FAO 300 through FAO 700) were grown in a 2-year field experiment in a semiarid irrigated area of central Spain. Genetic coefficients were obtained sequentially, starting with the phenological development parameters (P1, P2, P5 and PHINT), followed by the crop growth parameters (G2 and G3). The procedure was continued until the simulated outputs were in good agreement with the field phenological observations. After calibration, simulated parameters matched observed parameters well, with low RMSE in most cases. The calibrated P1 and P5 increased with the duration of the cycle. P1 was a linear function of the thermal time (TT) from emergence to silking and P5 was linearly related with the TT from silking to maturity . There were no significant differences in PHINT between hybrids from FAO-500 to 700 , as they had similar leaf number. Since phenological coefficients were directly related with the cycle duration, it would be possible to develop ranges and correlations which allow to estimate such coefficients from the cycle classification.

Improving simulation of soil water balance using lysimeter observations in a semiarid climate.

Water balance simulation in cropping systems is a very useful tool to study how water can be used efficiently. However this requires that models simulate an accurate water balance. Comparing model results with field observations will provide information on the performance of the models. The objective of this study was to test the performance of DSSAT model in simulating the water balance by comparing the simulations with observed measurements. The soil water balance in DSSAT uses a one dimensional ?tipping bucket? soil water balance approach where available soil water is determined by the drained upper limit (DUL), lower limit (LL) and saturated water content (SAT). A continuous weighing lysimeter was used to get the observed values of drainage and evapotranspiration (ET). An automated agrometeorological weather station close to the lisymeter was also used to record the climatic data. The model simulated accurately the soil water content after the optimization of the soil parameters. However it was found the inability of the model to capture small changes in daily drainage and ET. For that reason simulated cumulative values had larger errors as the time passed by. These results suggested the need to compare outputs of DSSAT and some hydrological model that simulates soil water movement with a more mechanistic approach. The comparison of the two models will allow us to find which mechanism can be modified or incorporated in DSSAT model to improve the simulations.

Saturn power generation with electrodynamic tethers in polar orbit

A power generation scheme based on bare electrodynamic tethers (EDT), working in passive mode is investigated for the purpose of supplying power to scientific missions at Saturn. The system employs a spinning EDT on a lowaltitude polar orbit which permits to efficiently convert plasmasphere energy into useful power. After optimizing the tether design for power generation we compute the supplied power along the orbit and the impact of the Lorentz force on the orbital elements as function of the tether and orbit characteristics. Although uncertainties in the current ionosphere density modeling strongly affect the performance of the system the peak power density of the EDT appears be greater than conventional power systems.

A review of electrodynamic tethers for science applications

A bare electrodynamic tether (EDT) is a conductive thin wire or tape tens of kilometres long, which is kept taut in space by gravity gradient or spinning, and is left bare of insulation to collect (and carry) current as a cylindrical Langmuir probe in an ambient magnetized plasma. An EDT is a probe in mesothermal flow at highly positive (or negative) bias, with a large or extremely large 2D sheath, which may show effects from the magnetic self-field of its current and have electrons adiabatically trapped in its ram front. Beyond technical applications ranging from propellantless propulsion to power generation in orbit, EDTs allow broad scientific uses such as generating electron beams and artificial auroras; exciting Alfven waves and whistlers; odifying the radiation belts; and exploring interplanetary space and the Jovian magnetosphere. Asymptotic analysis, numerical simulations, laboratory tests, and planned missions on EDTs are reviewed

Equity Carve Out : desde la óptica del PMO

Un Equity Carve Out, también conocido como escisión IPO o escisión parcial de empresas, constituye un tipo de reorganización corporativa, en la que una empresa crea una nueva filial a partir de la separación de una de sus actividades, negocios o servicios. Estas operaciones empresariales actualmente constituyen unas de las prácticas más comunes usadas por las compañías para conseguir financiación. El capital entrante por la venta de parte o la totalidad de la filial, justificará por un lado el esfuerzo invertido en el proceso y por otro abrirá nuevos caminos para la empresa recién constituida. Pero la mayor parte de estos procesos son de una complejidad elevada, tanto si se ven desde la óptica externa a la empresa, como interna. Por un lado las valoraciones bursátiles, dadas las actuales circunstancias económicas, no son las mejores. Y por otro, los proyectos de escisión tienen demasiados puntos críticos para considerarlos sencillos o mecánicos de ejecución. Este documento se centrará en dar solución a la problemática interna que afrontan las empresas una vez tomada la decisión de escindir una actividad: ¿cómo gestionar el proceso? Desde la experiencia y el conocimiento empresarial, se propone como solución: un proyecto completo, coherente y estructurado de escisión; y un PMO o responsable de proyecto, para dirigirlo. Durante todo el documento se repasarán todos y cada uno de los pasos que debe tener en consideración y llevar bajo control el PMO, para acabar el equity carve out en 5 meses. Se definirá un proyecto completo describiendo los pasos necesarios para: • Construir nueva empresa y las relaciones con su ecosistema. • Definir todas las operaciones de negocio necesarias para garantizar su operatividad. • Crear las estructuras necesarias que soporten todas las operaciones y procesos. Para ello y dentro de una planificación global, se propone el trabajo diario con todos los departamentos que tengan algún tipo de involucración en el proceso: operaciones, legal, recursos humanos, financiero, fiscal, TI, marketing y comunicación y compras. Todos estos departamentos o líneas de trabajo tendrán tareas y objetivos particulares. El documento servirá de manual, para que el PMO tenga una visión cuasi-completa de lo que hay que hacer en cada momento, con qué profesionales trabajar y con qué propósito. ---ABSTRACT---An Equity Carve Out, also named as excision or partial IPO excision of companies, is a type of corporate reorganization in which a company creates a new one from the separation of one of its activities, business or services. Currently these business operations constitute one of the most common practices used by companies to get funding. The capital that comes from the sale of part or the totality of the subsidiary, justifies the effort invested in the process on one hand, and on the other opens new perspectives for the newly formed company. But most of these processes are highly complex, whether viewed from outside the company, or from inside. On one side, stock valuations, taking into account the current economic circumstances, are not the best. And on the other side, excision projects have too many critical points to consider the projects simple or mechanical. This document is focused on resolving the internal problems faced by enterprises, once the decision of spinning off the activity is taken: how to manage the process? From the experience and business knowledge, we propose as solution: a complete, coherent and structured excision project; and a PMO or Project Officer leading it. Throughout the document, each and every step that the PMO must take into consideration will be reviewed, in order to finish the equity carve-out in 5 months. A complete project will be defined by describing the steps necessary to: • Build new business and relationships with its ecosystem. • Define all business operations necessary to ensure their operability. • Create the necessary structures that support all operations and processes. Within the Global Planning, we will propose daily work with all the departments that have some sort of involvement in the process: operations, legal, human resources, financial, taxes, IT, marketing communication and purchases. All these departments or working lines have their own tasks and goals. The document could be used as a manual for the PMO in order to have a near-complete picture of what to do anytime, with what professionals he/she would work and for what purpose.

Nueva estrategia de mercado en el sector de la moda: "Caso Blanco"

Este proyecto está realizado bajo el punto de vista del director de estrategia de la compañía, y tomando como punto de partida la situación de la marca a fecha de la adquisición por parte del grupo Alhokair, Enero del 2014. El objetivo es presentar al nuevo propietario de Blanco la estrategia a seguir, para no perder la esencia de la marca y a su vez generar valor, tanto económico como corporativo. Para su desarrollo es necesario disponer de información del sector veraz y contrastable. Por ello el estudio se realizará en base a la documentación obtenida de entidades fiables (cifras de negocio, situación de los mercados correspondientes al sector de la moda, entre otros datos mostrados); como son ACOTEX (Asociación Empresarial del Comercio Textil y Complementos, representativa de los empresarios y autónomos del sector y fundada en 1977), el ICEX (entidad pública empresarial de ámbito nacional encargada de promover la internacionalización de las empresas españolas), el INE (Instituto Nacional de Estadística) y el BORME (Boletín Oficial del Registro Mercantil). También en base a potenciales publicaciones web del sector como Modaes.es2, y prensa económica; Expansión3, Cinco días4 y el Economista5. Además de estas publicaciones y organismos, existen una gran cantidad de especialistas del sector que escriben artículos en prensa y en blogs, y que realizan charlas en importantes escuelas de moda y eventos, que han sido de gran ayuda para poder posicionarme con ‘comodidad’ en el rol que he asumido. Toda esta información; cuantitativa y cualitativa, basada en cifras, datos, estadísticas, conocimientos, experiencia y opiniones, junto con los conocimientos adquiridos en el Máster de Consultoría de Gestión de Empresas, principalmente en el módulo de estrategia, pero apoyándome e hilando con en el resto de módulos, he realizado este análisis y plan de acción con el fin de hacer renacer a Blanco. ---ABSTRACT---This project is conducted by the view of the director of company strategy, and taking as starting point the status of the brand as of the acquisition by the Alhokair group in January 2014. Aims to present the new owner Blanco's strategy to continue to keep the essence of the brand and in turn create economic and corporate value. For its development is necessary to have accurate and verifiable information of the sector. Therefore, the study will be based on documentation obtained from reliable entities. All quantitative and qualitative information based on facts, figures, statistics, knowledge, experience and views, along with the knowledge acquired in the Máster de Consultoría de Gestión de Empresas, mainly in the form of strategy, but leaning and spinning with the other modules, I have performed this analysis and action plan in order to be reborn Blanco.