Wedges and plate-bandes: mechanical theories after De la Hire

Plate-bandes are straight masonry arches (they are called, also, flat arches or lintel arches). Ideally they have the surfaces of extrados and intrados plane and horizontal. The stones or bricks have radial joints converging usually in one centre. The voussoirs have the form of wedges and in French they are called "claveaux". A plate-bande is, in fact, a lintel made of several stones and the proportions of lintels and plate-bandes are similar. Proportions of plate-bandes, that is the relationship between the thickness t and the span s (t/s)varies, typically between 1/4–1/3 in thick plate-bandes, and is less than 1/20 in the most slender ones. A ratio of circa 1/8 was usual in the 18th Century and follows a simple geometrical rule: the centre form with the intrados an equilateral triangle and the plate-bande should contain an arc of circle. The joints are usually plane, but in some cases present a «rebated» or «stepped» form. Plate-bandes exert an inclined thrust as any masonry arch. This thrust is usually very high and it requires either massive buttresses, or to be built in the middle of thick walls. Master builders and architects have tried since antiquity to calculate the abutment necessary for any arch. A modern architect or engineer will measure the arch thrust in units of force, kN or tons. Traditionally, the thrust has been measured as the size of the buttresses to resist it safely. Old structural rules, then, addressed the design problem establishing a relationship between the span and the depth of the buttress. These were empirical rules, particular for every type of arch or structure in every epoch. Thus, the typical gothic buttress is 1/4 of the vault span, but a Renaissance or baroque barrel vault will need more than 1/3 of the span. A plate-bande would require more than one half of the span; this is precisely the rule cited by the French engineer Gautier, who tried unsuccessfully to justify it by static reasons. They were used, typically, to form the lintels of windows or doors (1-2 m, typically); in Antiquity they were used, also, though rarely, at the gates of city walls or in niches (ca. 2 m, reaching 5.2 m). Plate-bandes may show particular problems: it is not unusual that some sliding of the voussoirs can be observed, particularly in thick plate-bandes. The stepped joints on Fig. 1, left, were used to avoid this problem. There are other «hidden» methods, like iron cramps or the use of stone wedges, etc. In seismic zones these devices were usual. Another problem relates to the deformation; a slight yielding of the abutments, or even the compression of the mortar joints, may lead to some cracking and the descent of the central keystone. Even a tiny descent will convert the original straight line of the intrados in a broken line with a visible «kink» or angle in the middle. Of course, both problems should be avoided. Finally, the wedge form of the voussoirs lead to acute angles in the stones and this can produce partial fractures; this occurs usually at the inferior border of the springers at the abutments. It follows, that to build a successful plate-bande is not an easy matter. Also, the structural study of plate-bandes is far from simple, and mechanics and geometry are related in a particular way. In the present paper we will concentrate on the structural aspects and their constructive consequences, with a historical approach. We will outline the development of structural analysis of plate-bandes from ca. 1700 until today. This brief history has a more than purely academic interest. Different approaches and theories pointed to particular problem, and though the solution given may have been incorrect, the question posed was often pertinent. The paper ends with the application of modern Limit Analysis of Masonry Structures, developed mainly by professor Heyman in the last fifty years. The work aims, also, to give some clues for the actual architect and engineer involved in the analysis or restoration of masonry buildings.

A Semantic Scraping Model for Web Resources - Applying Linked Data to Web Page Screen Scraping

In spite of the increasing presence of Semantic Web Facilities, only a limited amount of the available resources in the Internet provide a semantic access. Recent initiatives such as the emerging Linked Data Web are providing semantic access to available data by porting existing resources to the semantic web using different technologies, such as database-semantic mapping and scraping. Nevertheless, existing scraping solutions are based on ad-hoc solutions complemented with graphical interfaces for speeding up the scraper development. This article proposes a generic framework for web scraping based on semantic technologies. This framework is structured in three levels: scraping services, semantic scraping model and syntactic scraping. The first level provides an interface to generic applications or intelligent agents for gathering information from the web at a high level. The second level defines a semantic RDF model of the scraping process, in order to provide a declarative approach to the scraping task. Finally, the third level provides an implementation of the RDF scraping model for specific technologies. The work has been validated in a scenario that illustrates its application to mashup technologies

Digital signage application : developing a public venue multimedia touch-screen

La señalización digital o digital signage es una tecnología de comunicaciones digital que se está usando en los últimos años para reemplazar a la antigua publicidad impresa. Esta tecnología mejora la presentación y promoción de los productos anunciados, así como facilita el intercambio de información gracias a su colocación en lugares públicos o al aire libre. Las aplicaciones con las que cuenta este nuevo método de publicidad son muy variadas, ya que pueden variar desde ambientes privados en empresas, hasta lugares públicos como centros comerciales. Aunque la primera y principal utilidad de la señalización digital es la publicidad para que el usuario sienta una necesidad de adquirir productos, también la posibilidad de ofrecer más información sobre determinados artículos a través de las nuevas tecnologías es muy importante en este campo. La aplicación realizada en este proyecto es el desarrollo de un programa en Adobe Flash a través de lenguaje de programación XML. A través de una pantalla táctil, el usuario de un museo puede interactivamente acceder a un menú en el que aparecen los diferentes estilos de arte en un determinado tiempo de la historia. A través de una línea de tiempo se puede acceder a información sobre cada objeto que esté expuesto en la exhibición. Además se pueden observar imágenes de los detalles más importantes del objeto que no pueden ser vistos a simple vista, ya que no está permitido manipularlos. El empleo de la pantalla interactiva sirve para el usuario de la exhibición como una herramienta extra para recabar información sobre lo que está viendo, a través de una tecnología nueva y fácil de usar para todo el mundo, ya que solo se necesita usar las propias manos. La facilidad de manejo en aplicaciones como estas es muy importante, ya que el usuario final puede no tener conocimientos tecnológicos por lo que la información debe darse claramente. Como conclusión, se puede decir que digital signage es un mercado que está en expansión y que las empresas deben invertir en el desarrollo de contenidos, ya que las tecnologías avanzan aunque el digital signage no lo haga, y este sector podría ser muy útil en un futuro no muy lejano, ya que la información que es capaz de transmitir al espectador en todos los lugares es mucho más válida y útil que la proporcionada por un simple póster impreso en una valla publicitaria. Abstract The Digital signage is a digital communications technology being used in recent years to replace the old advertising printed. This technology improves the presentation and promotion of the advertised products, and makes easy the exchange of information with its placement in public places or outdoors. The applications that account this new method of advertising are several; they can range from private rooms in companies, to public places like malls. Although the first major utility of Digital signage is the advertising that makes the user feel and need of purchasing products. In addition, the chance of providing more information about certain items through new technologies is very important in this field. The application made in this project is the development of a program in Adobe Flash via XML programming language. Through a touch-screen, a museum user can interactively access a menu in which different styles of art in a particular time in history appears. Through a timeline you can access to information about each object that is exposed on display. Also you can see pictures of the most important details of the object that can not be seen with the naked eye, since it is not allowed to manipulate it. The use of the interactive screen serves to the user exhibition as an extra tool to gather information about what is seeing through a new technology and easy to use for everyone, since only need to use one’s own hands. The ease of handling in applications such as this is very important as the end user may not have expertise technology so the information should be clearly. As conclusion, one can say digital signage is an expansion market and companies must invest in content development, as although digital technologies advance digital signage does not, and this sector could be very useful in a near future, because information that is able of transmitting the everywhere viewer is much more valid and useful than that provided by a simple printed poster on a billboard.

Exercise during pregnancy improves maternal glucose screen at 24-28 weeks: a randomised controlled trial

Objective. The influence of an exercise programme performed by healthy pregnant women on maternal glucose tolerance was studied. Study design. A physical activity (PA, land/aquatic activities) programme during the entire pregnancy (three sessions per week) was conducted by a qualified instructor. 83 healthy pregnant women were randomly assigned to either an exercise group (EG, n=40) or a control (CG, n=43) group. 50 g maternal glucose screen (MGS), maternal weight gain and several pregnancy outcomes were recorded. Results. Significant differences were found between study groups on the 50 g MGS. Values corresponding to the EG (103.8±20.4 mg/dl) were better than those of the CG (126.9±29.5 mg/dl), p=0.000. In addition, no differences in maternal weight gain and no cases of gestational diabetes in EG versus 3 in CG (7%) (p>0.05) were found. Conclusion. A moderate PA programme performed during pregnancy improves levels of maternal glucose tolerance.

Wide-angle, high-concentration photovoltaics to compete with flat plate systems

A novel photovoltaic concentrator enables highly uniform irradiance on a small number of efficient solar cells. The maximum electrical power of a photovoltaic (PV) energy installation depends on three factors: the available irradiance, the size of the systems collecting sunlight, and the rate at which the device transforms light into electricity (the conversion efficiency). Developers can maximize the irradiance by carefully selecting the site and orientation of the solar facility. But they can only expand their sunlight collection systems for standard flat plate PV devices by increasing the number of solar cells, at greater cost. Here, we consider the advantages of an alternative PV system that produces more energy without increasing the number of cells used (actually, reducing it), by improving the conversion rates.We also present a new device that may enhance the commercial viability of such technologies.

Moment transfer and influence of transverse beams in interior waffle flat plate-column connections under lateral loading

This paper addresses two aspects of the behavior of interior reinforced concrete waffle flat plate?column connections under lateral loads: the share of the unbalanced moment between flexure and excentric shear, and the effect of the transverse beams. A non-linear finite element model (benchmark model) was developed and calibrated with the results of quasi-static cyclic tests conducted on a 3/5 scale specimen. First, from this numerical model, the portion cv of the unbalanced moment transferred by the excentricity of shear about the centroid of the critical sections defined by Eurocode 2 (EC-2) and by ACI 318-11 was calculated and compared with the share-out prescribed by these codes. It is found that while the critical section of EC-2 is consistent with the cv provided by this code, in the case of ACI 318-11, the value assigned to cv is far below (about 50% smaller) the actual one obtained with the numerical simulations. Second, from the benchmark model, seven additional models were developed by varying the depth D of the transverse beam over the thickness h of the plate. It was found that the ductility of the connection and the effective width of the plate can respectively be increased up to 50% and 10% by raising D/h to 2 and 1.5.

Laminar counterflow parallel-plate heat exchangers: Exact and approximate solutions

Multilayered, counterflow, parallel-plate heat exchangers are analyzed numerically and theoretically. The analysis, carried out for constant property fluids, considers a hydrodynamically developed laminar flow and neglects longitudinal conduction both in the fluid and in the plates. The solution for the temperature field involves eigenfunction expansions that can be solved in terms of Whittaker functions using standard symbolic algebra packages, leading to analytical expressions that provide the eigenvalues numerically. It is seen that the approximate solution obtained by retaining the first two modes in the eigenfunction expansion provides an accurate representation for the temperature away from the entrance regions, specially for long heat exchangers, thereby enabling simplified expressions for the wall and bulk temperatures, local heat-transfer rate, overall heat-transfer coefficient, and outlet bulk temperatures. The agreement between the numerical and theoretical results suggests the possibility of using the analytical solutions presented herein as benchmark problems for computational heat-transfer codes.

Analysis of plate bending by means of high order finite hyperelements

The possibilities and limitations of high order hyperelements in plate bending analysis are discussed. Explicit shape functions for some types of triangular elements are given. These elements are applied to simple cases to assess their computational efficiency.

A C1 finite element for Kirchhoff plate bending

After a short introduction the possibilities and limitations of polynomial simple elements with C1 continuity are discussed with reference to plate bending analysis. A family of this kind of elements is presented.. These elements are applied to simple cases in order to assess their computational efficiency. Finally some conclusions are shown, and future research is also proposed.

A computer formulation for the analysis on continuous non prismatic folded plate structures of arbitrary cross-section

A computer solution to analyze nonprismatic folded plate structures is shown. Arbitrary cross-sections (simple and multiple), continuity over intermediate supports and general loading and longitudinal boundary conditions are dealt with. The folded plates are assumed to be straight and long (beam like structures) and some simplifications are introduced in order to reduce the computational effort. The formulation here presented may be very suitable to be used in the bridge deck analysis.

A survey on folded plate structures

A compact formulation of the linear theory of folded plate structures utilizing matrix methods is given. Different usual approximations and comparison between them are also shown

A plastic analysis of nonprismatic folded plate structures

A computer method for the plastic analysis of folded plate structures is presented. The method considers the specific characteristics of the folded plate structural model using a simplified one-dimensional theory. and it can be applied to the analysis of any type of folded pIates, either prismatic or nonprismatic, with arbitrary cross-section. A simple example is analyzed in order to show the possibilities of the procedure and some results of interest are presented

The folded plate model in structural analysis. Elastic, plastic and dynamic formulations for nonprismatic structures

A specific numerical procedure for the analysis of arbitrary nonprismatic folded plate structures is presented. An elastic model is studied and compared with a harmonic solution for a prismatic structure. An extension to the plastic analysis is developed, and the influence of the structural geometry and loading pattern is analyzed. Nonprismatic practical cases, with arbitrary geometry and loading are shown, as well in the elastic range as in the plastic one. Finally, a dynamic formulation is outlined

Use of thermographic imaging to screen for drought-tolerant genotypes in Brachypodium distachyon

Thermal imaging has been used to evaluate the response to drought and warm temperatures in a collection of Brachypodium distachyon lines adapted to varied environmental conditions. Thermographic records were able to separate lines from contrasting rainfall regimes. Genotypes from dryer environments showed warmer leaves under water deficit, which suggested that decreased evapotranspiration was related to a more intense stomatal closure. When irrigated and under high temperature conditions, drought-adapted lines showed cooler leaves than lines from wetter zones. The consistent, inverse thermographic response of lines to water stress and heat validates the reliability of this method to assess drought tolerance in this model cereal. It additionally supports the hypothesis that stomatal-based mechanisms are involved in natural variation for drought tolerance in Brachypodium. The study further suggests that these mechanisms are not constitutive but likely related to a more efficient closing response to avoid dehydration in adapted genotypes. Higher leaf temperature under water deficit seems a dependable criterion of drought tolerance, not only in B. distachyon but also in the main cereal crops and related grasses where thermography can facilitate high-throughput preliminary screening of tolerant materials.

Application of the dynamic models to the detection of imperfections in plate Structures

This paper is part of a set of publications related with the development of mathematical models aimed to simulate the dynamic input and output of experimental nondestructive tests in order to detect structural imperfections. The structures to be considered are composed by steel plates of thin thickness. The imperfections in these cases are cracks and they can penetrate either a significant part of the plate thickness or be micro cracks or superficial imperfections. The first class of cracks is related with structural safety and the second one is more connected to the structural protection to the environment, particularly if protective paintings can be deteriorated. Two mathematical groups of models have been developed. The first group tries to locate the position and extension of the imperfection of the first class of imperfections, i.e. cracks and it is the object of the present paper. Bending Kirchoff thin plate models belong to this first group and they are used to this respect. The another group of models is dealt with membrane structures under the superficial Rayleigh waves excitation. With this group of models the micro cracks detection is intended. In the application of the first group of models to the detection of cracks, it has been observed that the differences between the natural frequencies of the non cracked and the cracked structures are very small. However, geometry and crack position can be identified quite accurately if this comparison is carried out between first derivatives (mode rotations) of the natural modes are used instead. Finally, in relation with the analysis of the superficial crack existence the use of Rayleigh waves is very promising. The geometry and the penetration of the micro crack can be detected very accurately. The mathematical and numerical treatment of the generation of these Rayleigh waves present and a numerical application has been shown.