Potential to attract drivers out of their cars in dense urban areas.

Purpose Sustainable mobility urban policies intend reducing car use and increasing walking, cycling and public transport. However, this transfer from private car to these more sustainable modes is only a real alternative where distances are small and the public transport supply competitive enough. This paper proposes a methodology to calculate the number of trips that can be transferred from private car to other modes in city centres. Method The method starts analyzing which kind of trips cannot change its mode (purposes, conditions, safety , etc.), and then setting a process to determine under which conditions trips made by car between given O-D pairs can be transferable. Then, the application of demand models allow to determine which trips fulfil the transferability conditions. The process test the possibility of transfer in a sequential way: firs to walking, then cycling and finally to public transport. Results The methodology is tested through its application to the city of Madrid (Spain), with the result of only some 18% of the trips currently made by car could be made by other modes, under the same conditions of trip time, and without affecting their characteristics. Out of these trips, 75% could be made by public transport, 15% cycling and 10% on foot. The possible mode to be transferred depends on the location: city centre areas are more favourable for walking and cycling while city skirts could attract more PT trips. Conclusions The proposed method has demonstrated its validity to determine the potential of transferring trips out of cars to more sustainable modes. Al the same time it is clear that, even in areas with favourable conditions for walking, cycling and PT trips, the potential of transfer is limited because cars fulfil more properly special requirements of some trips and tours.

Low-speed longitudinal controllers for mass-produced cars: A comparative study

Four longitudinal control techniques are compared: a classical Proportional-Integral (PI) control; an advanced technique-called the i-PI-that adds an intelligent component to the PI; a fuzzy controller based on human experience; and an adaptive-network-based fuzzy inference system. The controllers were designed to tackle one of the challenging topics as yet unsolved by the automotive sector: managing autonomously a gasoline-propelled vehicle at very low speeds. The dynamics involved are highly nonlinear and constitute an excellent test-bed for newly designed controllers. A Citroën C3 Pluriel car was modified to permit autonomous action on the accelerator and the brake pedals-i.e., longitudinal control. The controllers were tested in two stages. First, the vehicle was modeled to check the controllers' feasibility. Second, the controllers were then implemented in the Citroën, and their behavior under the same conditions on an identical real circuit was compared.

Using array based techniques for noise source identification in cars

Una de las principales causas del ruido en nuestras ciudades es el tráfico rodado. El ruido generado por los vehículos no es sólo debido al motor, sino que existen diversas fuentes de ruido en los mismos, entre las que se puede destacar el ruido de rodadura. Para localizar las causas del ruido e identificar las principales fuentes del mismo se han utilizado en diversos estudios las técnicas de coherencia y las técnicas basadas en arrays. Sin embargo, en la bibliografía existente, no es habitual encontrar el uso de estas técnicas en el sector automovilístico. En esta tesis se parte de la premisa de la posibilidad de usar estas técnicas de medida en coches, para demostrar a la largo de la misma su factibilidad y su bondad para evaluar las fuentes de ruido en dos condiciones distintas: cuando el coche está parado y cuando está en movimiento. Como técnica de coherencia se elige la de Intensidad Selectiva, utilizándose la misma para evaluar la coherencia existente entre el ruido que llega a los oídos del conductor y la intensidad radiada por distintos puntos del motor. Para la localización de fuentes de ruido, las técnicas basadas en array son las que mejores resultados ofrecen. Statistically Optimized Near-field Acoustical Holography (SONAH) es la técnica elegida para la localización y caracterización de las fuentes de ruido en el motor a baja frecuencia. En cambio, Beamforming es la técnica seleccionada para el caso de media-alta frecuencia y para la evaluación de las fuentes de ruido cuando el coche se encuentra en movimiento. Las técnicas propuestas no sólo pueden utilizarse en medidas reales, sino que además proporcionan abundante información y frecen una gran versatilidad a la hora de caracterizar fuentes de ruido. ABSTRACT One of the most important noise causes in our cities is the traffic. The noise generated by the vehicles is not only due to the engine, but there are some other noise sources. Among them the tyre/road noise can be highlighted. Coherence and array based techniques have been used in some research to locate the noise causes and identify the main noise sources. Nevertheless, it is not usual in the literature to find the application of this kind of techniques in the car sector. This Thesis starts taking into account the possibility of using this kind of measurement techniques in cars, to demonstrate their feasability and their quality to evaluate the noise sources under two different conditions: when the car is stopped and when it is in movement. Selective Intensity was chosen as coherence technique, evaluating the coherence between the noise in the driver’s ears and the intensity radiated in different points of the engine. Array based techniques carry out the best results to noise source location. Statistically Optimized Near-field Acoustical Holography (SONAH) is the measurement technique chosen for noise source location and characterization in the engine at low frequency. On the other hand, Beamforming is the technique chosen in the case of medium-high frequency and to characterize the noise sources when the car is in movement. The proposed techniques not only can be used in actual measurements, but also provide a lot of information and are very versatile to noise source characterization.

Stop cars: “Recuperación de un derecho ciudadano”

Durante el siglo XX, hemos pasado de ser una sociedad activa que disfrutaba de la ciudad a medida que recorría sus calles, a ser una sociedad motorizada cuyo interés principal es transportarse de un punto A a un punto B en el menor tiempo posible. En este siglo XXI, la concepción del espacio urbano y de la vida cotidiana se encuentra en un movimiento de rechazo de esta ideología anterior. Ya no nos interesan esas ciudades funcionales diseñadas solamente para los vehículos y un movimiento de recuperación del espacio urbano se ha iniciado sobre una trama de ciudad todavía anclada en el pasado. Este ensayo pretende analizar los retos provenientes de este cambio ideológico y dar una serie de soluciones a la conversión de espacios públicos de tránsito en espacios de estar al aire libre que den pie a una sinergia comunicativa de sus gentes. Hoy en día nos encontramos con los inicios de este movimiento de cambio que busca una mejora en la salud y la vida cotidiana de los ciudadanos, previamente relegados a espacios libres públicos muy acotados. Ahora, todo el espacio libre se convierte en espacio para sus ciudadanos buscando crear de esta forma una “sala de estar” al aire libre.

Numerical and experimental study of appendages in racing yachts and their influence on the free surface

Las prestaciones de un velero de regatas se estiman por medio de los Programas de Predicción de Velocidad (VPP) que incluyen las características de estabilidad y modelos aero e hidrodinámico del barco. Por esta razón, es importante tener una evaluación adecuada de las fuerzas en apéndices y de su variación en diferentes condiciones de navegación, escora y deriva. Además, para el cálculo de las fuerzas en los apéndices es importante conocer sus características hidrodinámicas cuando trabajan conjuntamente en un campo fluido fuertemente modificado por la carena. Por esta razón, se han utilizado una serie de ensayos realizados en el Canal de Ensayos de la ETSIN con el objetivo de validar códigos numéricos que permiten una evaluación más rápida y focalizada en los distintos fenómenos que se producen. Dichos ensayos se han realizado de forma que pudiera medirse independientemente las fuerzas hidrodinámicas en cada apéndice, lo que permitirá evaluar el reparto de fuerzas en diferentes condiciones de navegación para poder profundizar en las interacciones entre carena, quilla y timón. Las técnicas numéricas permiten capturar detalles que difícilmente se pueden visualizar en ensayos experimentales. En este sentido, se han probado las últimas técnicas utilizadas en los últimos workshops y se ha enfocado el estudio a un nuevo método con el objetivo de mostrar una metodologia más rápida que pueda servir a la industria para este tipo de aproximación al problema. ABSTRACT The performances of a racing sailboat are estimated by means of the speed prediction programs (VPP), which include the ship stability characteristics and the aero and hydrodynamic models. For this reason, it is important to have an adequate evaluation of the forces in appendices and its variation in different sailing conditions, heel and leeway Moreover, for the analysis of the forces in the appendices, it is important to know their hydrodynamic characteristics when they work together in a fluid field strongly modified by the canoe body. For this reason, several tests have been done in the ETSIN towing tank with the aim to validate numeric codes that allowing faster analysis and they permit to focus on the different phenomena that occur there. Such tests have been done in a way that the hydrodynamic forces in each appendage could be measured independently allowing assessing the distribution of forces in different sailing conditions to be able to deepen the interactions between the canoe body, the keel and the rudder. Numerical techniques allow capturing details that can hardly be displayed in experimental tests. In this sense, the latest techniques used in the recent workshops have been reviewed and the study has been focused to propose a new model with the aim to show a new faster methodology which serves the industry for this type of approach to the problem.

Telemetría de vehículos FSAE con microcontrolador PIC32 y transceptor de radio CC1101

Quizás el campo de las telecomunicaciones sea uno de los campos en el que más se ha progresado en este último siglo y medio, con la ayuda de otros campos de la ciencia y la técnica tales como la computación, la física electrónica, y un gran número de disciplinas, que se han utilizado estos últimos 150 años en conjunción para mejorarse unas con la ayuda de otras. Por ejemplo, la química ayuda a comprender y mejorar campos como la medicina, que también a su vez se ve mejorada por los progresos en la electrónica creados por los físicos y químicos, que poseen herramientas más potentes para calcular y simular debido a los progresos computacionales. Otro de los campos que ha sufrido un gran avance en este último siglo es el de la automoción, aunque estancados en el motor de combustión, los vehículos han sufrido enormes cambios debido a la irrupción de los avances en la electrónica del automóvil con multitud de sistemas ya ampliamente integrados en los vehículos actuales. La Formula SAE® o Formula Student es una competición de diseño, organizada por la SAE International (Society of Automotive Engineers) para estudiantes de universidades de todo el mundo que promueve la ingeniería a través de una competición donde los miembros del equipo diseñan, construyen, desarrollan y compiten en un pequeño y potente monoplaza. En el ámbito educativo, evitando el sistema tradicional de clases magistrales, se introducen cambios en las metodologías de enseñanza y surge el proyecto de la Fórmula Student para lograr una mejora en las acciones formativas, que permitan ir incorporando nuevos objetivos y diseñar nuevas situaciones de aprendizaje que supongan una oportunidad para el desarrollo de competencias de los alumnos, mejorar su formación como ingenieros y contrastar sus progresos compitiendo con las mejores universidades del mundo. En este proyecto se pretende dotar a los alumnos de las escuelas de ingeniería de la UPM que desarrollan el vehículo de FSAE de una herramienta de telemetría con la que evaluar y probar comportamiento del vehículo de FSAE junto con sus subsistemas que ellos mismos diseñan, con el objetivo de evaluar el comportamiento, introducir mejoras, analizar resultados de una manera más rápida y cómoda, con el objetivo de poder progresar más rápidamente en su desarrollo, recibiendo y almacenando una realimentación directa e instantánea del funcionamiento mediante la lectura de los datos que circulan por el bus CAN del vehículo. También ofrece la posibilidad de inyectar datos a los sistemas conectados al bus CAN de manera remota. Se engloba en el conjunto de proyectos de la FSAE, más concretamente en los basados en la plataforma PIC32 y propone una solución conjunta con otros proyectos o también por sí sola. Para la ejecución del proyecto se fabricó una placa compuesta de dos placas de circuito impreso, la de la estación base que envía comandos, instrucciones y datos para inyectar en el bus CAN del vehículo mediante radiofrecuencia y la placa que incorpora el vehículo que envía las tramas que circulan por el bus CAN del vehículo con los identificadores deseados, ejecuta los comandos recibidos por radiofrecuencia y salva las tramas CAN en una memoria USB o SD Card. Las dos PCBs constituyen el hardware del proyecto. El software se compone de dos programas. Un programa para la PCB del vehículo que emite los datos a la estación base, codificado en lenguaje C con ayuda del entorno de desarrollo MPLAB de Microchip. El otro programa hecho con LabView para la PCB de la estación base que recibe los datos provenientes del vehículo y los interpreta. Se propone un hardware y una capa o funciones de software para los microcontroladores PIC32 (similar al de otros proyectos del FSAE) para la transmisión de las tramas del bus CAN del vehículo de manera inalámbrica a una estación base, capaz de insertar tramas en el bus CAN del vehículo enviadas desde la estación base. También almacena estas tramas CAN en un dispositivo USB o SD Card situado en el vehículo. Para la transmisión de los datos se hizo un estudio de las frecuencias de transmisión, la legislación aplicable y los tipos de transceptores. Se optó por utilizar la banda de radiofrecuencia de uso común ISM de 433MHz mediante el transceptor integrado CC110L de Texas Instruments altamente configurable y con interfaz SPI. Se adquirieron dos parejas de módulos compatibles, con amplificador de potencia o sin él. LabView controla la estación que recoge las tramas CAN vía RF y está dotada del mismo transceptor de radio junto con un puente de comunicaciones SPI-USB, al que se puede acceder de dos diferentes maneras, mediante librerías dll, o mediante NI-VISA con transferencias RAW-USB. La aplicación desarrollada posee una interfaz configurable por el usuario para la muestra de los futuros sensores o actuadores que se incorporen en el vehículo y es capaz de interpretar las tramas CAN, mostrarlas, gráfica, numéricamente y almacenar esta información, como si fuera el cuadro de instrumentos del vehículo. Existe una limitación de la velocidad global del sistema en forma de cuello de botella que se crea debido a las limitaciones del transceptor CC110L por lo que si no se desea filtrar los datos que se crean necesarios, sería necesario aumentar el número de canales de radio para altas ocupaciones del bus CAN. Debido a la pérdida de relaciones con el INSIA, no se pudo probar de manera real en el propio vehículo, pero se hicieron pruebas satisfactorias (hasta 1,6 km) con una configuración de tramas CAN estándar a una velocidad de transmisión de 1 Mbit/s y un tiempo de bit de 1 microsegundo. El periférico CAN del PIC32 se programará para cumplir con estas especificaciones de la ECU del vehículo, que se presupone que es la MS3 Sport de Bosch, de la que LabView interpretará las tramas CAN recibidas de manera inalámbrica. Para poder probar el sistema, ha sido necesario reutilizar el hardware y adaptar el software del primer prototipo creado, que emite tramas CAN preprogramadas con una latencia también programable y que simulará al bus CAN proporcionando los datos a transmitir por el sistema que incorpora el vehículo. Durante el desarrollo de este proyecto, en las etapas finales, el fabricante del puente de comunicaciones SPI-USB MCP2210 liberó una librería (dll) compatible y sin errores, por lo que se nos ofrecía una oportunidad interesante para la comparación de las velocidades de acceso al transceptor de radio, que se presuponía y se comprobó más eficiente que la solución ya hecha mediante NI-VISA. ABSTRACT. The Formula SAE competition is an international university applied to technological innovation in vehicles racing type formula, in which each team, made up of students, should design, construct and test a prototype each year within certain rules. The challenge of FSAE is that it is an educational project farther away than a master class. The goal of the present project is to make a tool for other students to use it in his projects related to FSAE to test and improve the vehicle, and, the improvements that can be provided by the electronics could be materialized in a victory and win the competition with this competitive advantage. A telemetry system was developed. It sends the data provided by the car’s CAN bus through a radio frequency transceiver and receive commands to execute on the system, it provides by a base station on the ground. Moreover, constant verification in real time of the status of the car or data parameters like the revolutions per minute, pressure from collectors, water temperature, and so on, can be accessed from the base station on the ground, so that, it could be possible to study the behaviour of the vehicle in early phases of the car development. A printed circuit board, composed of two boards, and two software programs in two different languages, have been developed, and built for the project implementation. The software utilized to design the PCB is Orcad10.5/Layout. The base station PCB on a PC receives data from the PCB connected to the vehicle’s CAN bus and sends commands like set CAN filters or masks, activate data logger or inject CAN frames. This PCB is connected to a PC via USB and contains a bridge USB-SPI to communicate with a similar transceiver on the vehicle PCB. LabView controls this part of the system. A special virtual Instrument (VI) had been created in order to add future new elements to the vehicle, is a dashboard, which reads the data passed from the main VI and represents them graphically to studying the behaviour of the car on track. In this special VI other alums can make modifications to accommodate the data provided from the vehicle CAN’s bus to new elements on the vehicle, show or save the CAN frames in the form or format they want. Two methods to access to SPI bus of CC110l RF transceiver over LabView have been developed with minimum changes between them. Access through NI-VISA (Virtual Instrument Software Architecture) which is a standard for configuring, programming, USB interfaces or other devices in National Instruments LabView. And access through DLL (dynamic link library) supplied by the manufacturer of the bridge USB-SPI, Microchip. Then the work is done in two forms, but the dll solution developed shows better behaviour, and increase the speed of the system because has less overload of the USB bus due to a better efficiency of the dll solution versus VISA solution. The PCB connected to the vehicle’s CAN bus receives commands from the base station PCB on a PC, and, acts in function of the command or execute actions like to inject packets into CAN bus or activate data logger. Also sends over RF the CAN frames present on the bus, which can be filtered, to avoid unnecessary radio emissions or overflowing the RF transceiver. This PCB consists of two basic pieces: A microcontroller with 32 bit architecture PIC32MX795F512L from Microchip and the radio transceiver integrated circuit CC110l from Texas Instruments. The PIC32MX795F512L has an integrated CAN and several peripherals like SPI controllers that are utilized to communicate with RF transceiver and SD Card. The USB controller on the PIC32 is utilized to store CAN data on a USB memory, and change notification peripheral is utilized like an external interrupt. Hardware for other peripherals is accessible. The software part of this PCB is coded in C with MPLAB from Microchip, and programming over PICkit 3 Programmer, also from Microchip. Some of his libraries have been modified to work properly with this project and other was created specifically for this project. In the phase for RF selection and design is made a study to clarify the general aspects of regulations for the this project in order to understand it and select the proper band, frequency, and radio transceiver for the activities developed in the project. From the different options available it selects a common use band ICM, with less regulation and free to emit with restrictions and disadvantages like high occupation. The transceiver utilized to transmit and receive the data CC110l is an integrated circuit which needs fewer components from Texas Instruments and it can be accessed through SPI bus. Basically is a state machine which changes his state whit commands received over an SPI bus or internal events. The transceiver has several programmable general purpose Inputs and outputs. These GPIOs are connected to PIC32 change notification input to generate an interrupt or connected to GPIO to MCP2210 USB-SPI bridge to inform to the base station for a packet received. A two pair of modules of CC110l radio module kit from different output power has been purchased which includes an antenna. This is to keep away from fabrication mistakes in RF hardware part or designs, although reference design and gerbers files are available on the webpage of the chip manufacturer. A neck bottle is present on the complete system, because the maximum data rate of CC110l transceiver is a half than CAN bus data rate, hence for high occupation of CAN bus is recommendable to filter the data or add more radio channels, because the buffers can’t sustain this load along the time. Unfortunately, during the development of the project, the relations with the INSIA, who develops the vehicle, was lost, for this reason, will be made impossible to test the final phases of the project like integration on the car, final test of integration, place of the antenna, enclosure of the electronics, connectors selection, etc. To test or evaluate the system, it was necessary to simulate the CAN bus with a hardware to feed the system with entry data. An early hardware prototype was adapted his software to send programed CAN frames at a fixed data rate and certain timing who simulate several levels of occupation of the CAN Bus. This CAN frames emulates the Bosch ECU MS3 Sport.

Velero de competición capacitado para la regata alrededor del mundo “Volvo Ocean Race.”

TIPO DE BUQUE: Velero de competición capacitado para la regata alrededor del mundo “Volvo Ocean Race.” REGLAMENTOS: Reglas de la clase: Volvo Ocean 60 rule 2000 + changes CLASIFICACIÓN: ABS Guide for Building and Classing Offshore Racing Yachts 1994 incorporating Notice #1 DESPLAZAMIENTO MÁXIMO: 15000 KG CALADO MÁXIMO: 3.75 m ESLORA MÁXIMA: 23.5 m CONSTRUCCIÓN: Casco: Materiales compuestos. Mástil: materiales compuestos sin núcleo o aluminio. INSTALACIÓN ELÉCTRICA: 24V DC con un motor auxiliar y al menos dos alternadores independientes. SISTEMA DE PROPULSIÓN: Vela, aparejo tipo Sloop. Motor propulsivo de emergencia con hélice plegable de dos palas capaz de dar 7 nudos en condiciones de mar en calma ALOJAMIENTO: para 12 tripulantes REQUERIMIENTOS: Desaladora-potabilizadora, radar, GPS, GMDSS, comunicaciones por satélite Inmarsat B y C, sistema de gobierno de emergencia, calefacción, bombas de lastre, sistema de corrección de escora mediante tanques de lastre liquido.

Evaluation of the influence of toll systems on energy consumption and CO2 emissions: A case study of a Spanish highway

This paper studies the energy consumption and subsequent CO2 emissions of road highway transportation under three toll systems in Spain for four categories of vehicles: cars, vans, buses and articulated trucks. The influence of toll systems is tested for a section of AP-41 highway between Toledo and Madrid. One system is free flow, other is traditional stop and go and the last toll system operates with an electronic toll collection (ETC) technology. Energy consumption and CO2 emissions were found to be closely related to vehicle mass, wind exposure, engine efficiency and acceleration rate. These parameters affect, directly or indirectly, the external forces which determine the energy consumption. Reducing the magnitude of these forces through an appropriate toll management is an important way of improving the energy performance of vehicles. The type of toll system used can have a major influence on the energy efficiency of highway transportation and therefore it is necessary to consider free flow.

An Aspect-Oriented Approach for Supporting Autonomic Reconfiguration of Software Architecture

The increasing complexity of current software systems is encouraging the development of self-managed software architectures, i.e. systems capable of reconfiguring their structure at runtime to fulfil a set of goals. Several approaches have covered different aspects of their development, but some issues remain open, such as the maintainability or the scalability of self-management subsystems. Centralized approaches, like self-adaptive architectures, offer good maintenance properties but do not scale well for large systems. On the contrary, decentralized approaches, like self-organising architectures, offer good scalability but are not maintainable: reconfiguration specifications are spread and often tangled with functional specifications. In order to address these issues, this paper presents an aspect-oriented autonomic reconfiguration approach where: (1) each subsystem is provided with self-management properties so it can evolve itself and the components that it is composed of; (2) self-management concerns are isolated and encapsulated into aspects, thus improving its reuse and maintenance. Povzetek: Predstavljen je pristop s samo-preoblikovanjem programske arhitekture.

Dynamic effect of high speed railway traffic loads on the ballast track settlement

The traditional ballast track structures are still being used in high speed railways lines with success, however technical problems or performance features have led to non-ballast track solution in some cases. A considerable maintenance work is needed for ballasted tracks due to the track deterioration. Therefore it is very important to understand the mechanism of track deterioration and to predict the track settlement or track irregularity growth rate in order to reduce track maintenance costs and enable new track structures to be designed. The objective of this work is to develop the most adequate and efficient models for calculation of dynamic traffic load effects on railways track infrastructure, and then evaluate the dynamic effect on the ballast track settlement, using a ballast track settlement prediction model, which consists of the vehicle/track dynamic model previously selected and a track settlement law. The calculations are based on dynamic finite element models with direct time integration, contact between wheel and rail and interaction with railway cars. A initial irregularity profile is used in the prediction model. The track settlement law is considered to be a function of number of loading cycles and the magnitude of the loading, which represents the long-term behavior of ballast settlement. The results obtained include the track irregularity growth and the contact force in the final interaction of numerical simulation

Survey and brain storming studies about machines, constructions, human and environmental risk consideration in the careers of the Universidad Politécnica of Madrid

The Universidad Politécnica of Madrid (UPM) includes schools and faculties that were for engineering degrees, architecture and computer science, that are now in a quick EEES Bolonia Plan metamorphosis getting into degrees, masters and doctorate structures. They are focused towards action in machines, constructions, enterprises, that are subjected to machines, human and environment created risks. These are present in actions such as use loads, wind, snow, waves, flows, earthquakes, forces and effects in machines, vehicles behavior, chemical effects, and other environmental factors including effects of crops, cattle and beasts, forests, and varied essential economic and social disturbances. Emphasis is for authors in this session more about risks of natural origin, such as for hail, winds, snow or waves that are not exactly known a priori, but that are often considered with statistical expected distributions giving extreme values for convenient return periods. These distributions are known from measures in time, statistic of extremes and models about hazard scenarios and about responses of man made constructions or devices. In each engineering field theories were built about hazards scenarios and how to cover for important risks. Engineers must get that the systems they handle, such as vehicles, machines, firms or agro lands or forests, obtain production with enough safety for persons and with decent economic results in spite of risks. For that risks must be considered in planning, in realization and in operation, and safety margins must be taken but at a reasonable cost. That is a small level of risks will often remain, due to limitations in costs or because of due to strange hazards, and maybe they will be covered by insurance in cases such as in transport with cars, ships or aircrafts, in agro for hail, or for fire in houses or in forests. These and other decisions about quality, security for men or about business financial risks are sometimes considered with Decision Theories models, using often tools from Statistics or operational Research. The authors have done and are following field surveys about risk consideration in the careers in UPM, making deep analysis of curricula taking into account the new structures of degrees in the EEES Bolonia Plan, and they have considered the risk structures offered by diverse schools of Decision theories. That gives an aspect of the needs and uses, and recommendations about improving in the teaching about risk, that may include special subjects especially oriented for each career, school or faculty, so as to be recommended to be included into the curricula, including an elaboration and presentation format using a multi-criteria decision model.

Influence of driving style on fuel consumption and Emissions in diesel-powered passenger car

This paper presents the main results of a study on the influence of driving style on fuel consumption and pollutant emissions of diesel passenger car in urban traffic. Driving styles (eco, normal or aggressive) patterns were based on the “eco-driving” criteria. The methodology is based on on-board emission measurements in real urban traffic in the city of Madrid. Five diesel passenger cars, have been tested. Through a statistical analysis, a Dynamic Performance Index was defined for diesel passenger cars. Likewise, the CO, NOX and HC emissions were compared for each driving style for the tested vehicles. Eco-driving reduces by 14% fuel consumption and CO2 emissions, but aggressive driving increase consumption by 40%. Aggressive driving increases NOX emission by more than 40%. CO and HC, show different trends, but being increased in eco-driving style.

Proposal of a dynamic performance index to analyze driving pattern effect on car emissions

The contributions of driver behaviour as well as surrounding infrastructure are decisive on pollutant emissions from vehicles in real traffic situations. This article deals with the preliminary study of the interaction between the dynamic variables recorded in a vehicle (driving pattern) and pollutant emissions produced over a given urban route. It has been established a “dynamic performance index”-DPI, which is calculated from some driving pattern parameters, which in turn depends on traffic congestion level and route characteristics, in order to determine whether the driving has been aggressive, normal or calm. Two passenger cars instrumented with a portable activity measurement system -to record dynamic variables- and on-board emission measurement equipment have been used. This study has shown that smooth driving patterns can reduce up to 80% NOX emissions and up to 20% of fuel in the same route

Autonomous vehicle control systems for safe crossroads

This article presents a cooperative manoeuvre among three dual mode cars – vehicles equipped with sensors and actuators, and that can be driven either manually or autonomously. One vehicle is driven autonomously and the other two are driven manually. The main objective is to test two decision algorithms for priority conflict resolution at intersections so that a vehicle autonomously driven can take their own decision about crossing an intersection mingling with manually driven cars without the need for infrastructure modifications. To do this, the system needs the position, speeds, and turning intentions of the rest of the cars involved in the manoeuvre. This information is acquired via communications, but other methods are also viable, such as artificial vision. The idea of the experiments was to adjust the speed of the manually driven vehicles to force a situation where all three vehicles arrive at an intersection at the same time.

Making Transport Safer: V2V-Based Automated Emergency Braking System

An important goal in the field of intelligent transportation systems (ITS) is to provide driving aids aimed at preventing accidents and reducing the number of traffic victims. The commonest traffic accidents in urban areas are due to sudden braking that demands a very fast response on the part of drivers. Attempts to solve this problem have motivated many ITS advances including the detection of the intention of surrounding cars using lasers, radars or cameras. However, this might not be enough to increase safety when there is a danger of collision. Vehicle to vehicle communications are needed to ensure that the other intentions of cars are also available. The article describes the development of a controller to perform an emergency stop via an electro-hydraulic braking system employed on dry asphalt. An original V2V communication scheme based on WiFi cards has been used for broadcasting positioning information to other vehicles. The reliability of the scheme has been theoretically analyzed to estimate its performance when the number of vehicles involved is much higher. This controller has been incorporated into the AUTOPIA program control for automatic cars. The system has been implemented in Citroën C3 Pluriel, and various tests were performed to evaluate its operation.