A proposed parameterization of interface discontinuity factors depending on neighborhood for pin-by-pin diffusion computations for LWR

There exists an interest in performing full core pin-by-pin computations for present nuclear reactors. In such type of problems the use of a transport approximation like the diffusion equation requires the introduction of correction parameters. Interface discontinuity factors can improve the diffusion solution to nearly reproduce a transport solution. Nevertheless, calculating accurate pin-by-pin IDF requires the knowledge of the heterogeneous neutron flux distribution, which depends on the boundary conditions of the pin-cell as well as the local variables along the nuclear reactor operation. As a consequence, it is impractical to compute them for each possible configuration. An alternative to generate accurate pin-by-pin interface discontinuity factors is to calculate reference values using zero-net-current boundary conditions and to synthesize afterwards their dependencies on the main neighborhood variables. In such way the factors can be accurately computed during fine-mesh diffusion calculations by correcting the reference values as a function of the actual environment of the pin-cell in the core. In this paper we propose a parameterization of the pin-by-pin interface discontinuity factors allowing the implementation of a cross sections library able to treat the neighborhood effect. First results are presented for typical PWR configurations.

Gasoducto Yela-El Villar de Arnedo

Se realiza el diseño de un gasoducto requerido para la conexión del nuevo almacenamiento subterráneo de Yela con la red de gasoductos existentes. Se plantea un trazado alternativo al original, debido a circunstancias legales y administrativas que han provocado su variación. En el proyecto se muestran los datos básicos de diseño, criterios de cálculo, planos y pliegos de condiciones y el correspondiente presupuesto de las instalaciones. ABSTRACT This project analyzes the design of a pipeline required to connect the new underground storage Yela with existing pipeline network. An alternative route is proposed to the original, due to legal and administrative circumstances . The project shows the basic design data, calculation criteria, plans and specifications and the corresponding budget installations.

La barrera del análisis estructural y la representación gráfica en el desarrollo de los proyectos arquitectónicos: el caso de la Ópera de Sidney

En numerosas ocasiones a lo largo de la historia la imaginación de los creadores ha ido por delante de las posibilidades técnicas de cada momento. Así, muchas de estas nuevas ideas han requerido largos periodos de tiempo para materializarse como realidad construida, hasta que el desarrollo tecnológico e industrial hubo alcanzado un grado de madurez suficiente. En el campo de la arquitectura, estas limitaciones técnicas se han ido acotando paulatinamente hasta desembocar en la situación actual en la que cualquier planteamiento formal puede ser representado gráficamente y analizado desde un punto de vista estructural, superádose de este modo la barrera existente históricamente en el tratamiento de las formas. A lo largo del presente tesis doctoral se analiza cómo la formulación del Método de los Elementos Finitos en la década de los cincuenta y las curvas de Bézier en la década de los sesenta del siglo pasado y la posterior generalización de los ordenadores personales y de los programas informáticos asociados (C.A.D. y F.E.M. principalmente) en los estudios de arquitectura e ingeniería a partir de la década de los noventa, posibilitó el desarrollo de cualquier propuesta arquitectónica, por compleja que ésta fuese, provocando una verdadera revolución a nivel formal en el mundo de la arquitectura, especialmente en el campo de la edificación singular o icónica. Se estudia este proceso a través de ocho edificios; cuatro anteriores y otros tantos posteriores a la desaparición de la barrera anteriormente referida, establecida de forma simbólica en la década de los años ochenta del siglo XX: Frontón de Recoletos en Madrid, Edificio Seagram en Nueva York, Habitat ’67 en Montreal, Ópera de Sídney, museo Guggenheim de Bilbao, ampliación del Victoria & Albert Museum en Londres, tanatorio “Meiso no Mori” en Gifu y nueva sede de la CCTV en Pekín. De entre ellos, la Ópera de Sídney, obra del arquitecto danés Jørn Utzon, condensa gran parte de los aspectos relevantes investigados en relación a la influencia que los métodos de representación y análisis estructural ejercen en la concepción y construcción de las obras de arquitectura. Por este motivo y por considerarse un hito de la arquitectura a nivel global se toma como caso de estudio. La idea general del edificio, que data de 1956, se enmarca en una época inmediatamente anterior a la del desarrollo científico y tecnológico anteriormente referido. Esta ausencia de herramientas de diseño disponibles acordes a la complejidad formal de la propuesta planteada condicionó enormente la marcha del proyecto, dilatándose dramáticamente en el tiempo y disparándose su coste hasta el punto de que el propio arquitecto danés fue separado de las obras antes de su conclusión. Además, la solución estructural finalmente construida de las cubiertas dista mucho de la prevista por Utzon inicialmente. Donde él había imaginado unas finas láminas de hormigón flotando sobre el paisaje se materializó una estructura más pesada, formada por costillas pretensadas de hormigón con unas secciones notablemente mayores. La forma también debió ser modificada de modo ostensible respecto a la propuesta inicial. Si este edificio se pretendiese construir en la actualidad, con toda seguridad el curso de los acontecimientos se desarrollaría por senderos muy diferentes. Ante este supuesto, se plantean las siguientes cuestiones: ¿sería posible realizar un análisis estructural de la cubierta laminar planteada por Utzon inicialmente en el concurso con las herramientas disponibles en la actualidad?; ¿sería dicha propuesta viable estructuralmente?. A lo largo de las siguientes páginas se pretende dar respuesta a estas cuestiones, poniendo de relieve el impacto que los ordenadores personales y los programas informáticos asociados han tenido en la manera de concebir y construir edificios. También se han analizado variantes a la solución laminar planteada en la fase de concurso, a través de las cuales, tratando en la medida de lo posible de ajustarse a las sugerencias que Ove Arup y su equipo realizaron a Jørn Utzon a lo largo del dilatado proceso de proyecto, mejorar el comportamiento general de la estructura del edificio. Por último, se ha pretendido partir de cero y plantear, desde una perspectiva contemporánea, posibles enfoques metodológicos aplicables a la búsqueda de soluciones estructurales compatibles con la forma propuesta originalmente por Utzon para las cubiertas de la Ópera de Sídney y que nunca llegó a ser construida (ni analizada), considerando para ello los medios tecnológicos, científicos e industriales disponibles en la actualidad. Abstract On numerous occasions throughout history the imagination of creators has gone well beyond of the technical possibilities of their time. Many new ideas have required a long period to materialize, until the technological and industrial development had time to catch up. In the architecture field, these technical limitations have gradually tightened leading to the current situation in which any formal approach can be represented and analyzed from a structural point of view, thus concluding that the structural analysis and the graphical representation’s barrier in the development of architectural projects has dissappeared. Throughout the following pages it is examined how the development of the Finite Element Method in the fifties and the Bezier curves in the sixties of the last century and the subsequent spread of personal computers and specialized software in the architectural and engineering offices from the nineties, enabled the development of any architectural proposal independently of its complexity. This has caused a revolution at a formal level in architecture, especially in the field of iconic building. This process is analyzed through eight buildings, four of them before and another four after the disappearance of the above mentioned barrier, roughly established in the eighties of the last century: Fronton Recoletos in Madrid, Seagram Building in New York Habitat '67 in Montreal, Sydney Opera House, Guggenheim Museum Bilbao, Victoria & Albert Museum extension in London, Crematorium “Meiso no Mori” in Gifu and the new CCTV headquarters in Beijing. Among them, the Sydney Opera House, designed by Danish architect Jørn Utzon, condenses many of the main aspects previously investigated regarding the impact of representation methods and structural analysis on the design and construction of architectural projects. For this reason and also because it is considered a global architecture milestone, it is selected as a case study. The building’s general idea, which dates from 1956, is framed at a time immediately preceding the above mentioned scientific and technological development. This lack of available design tools in accordance with the proposal’s formal complexity conditioned enormously the project’s progress, leading to a dramatic delay and multiplying the final budget disproportionately to the point that the Danish architect himself was separated from the works before completion. Furthermore, the built structure differs dramatically from the architect’s initial vision. Where Utzon saw a thin concrete shell floating over the landscape a heavier structure was built, consisting of prestressed concrete ribs with a significantly greater size. The geometry also had to be modified. If this building were to built today, the course of events surely would walk very different paths. Given this assumption, a number of questions could then be formulated: Would it be possible to perform a structural analysis of Utzon’s initially proposed competition-free-ways roof’s geometry with the tools available nowadays?; Would this proposal be structurally feasable?. Throughout the following pages it is intended to clarify this issues, highlighting personal computers and associated software’s impact in building design and construction procedures, especially in the field of iconic building. Variants have also been analyzed for the laminar solution proposed in the competition phase, through which, trying as far as possible to comply with the suggestions that Ove Arup and his team did to Jørn Utzon along the lengthy process project, improving the overall performance of the building structure. Finally, we have started from scratch and analyzed, from a contemporary perspective, possible structural solutions compatible with Utzon’s Opera House’s original geometry and vision –proposal that was never built (nor even analyzed)-, taking into consideration the technological, scientific and industrial means currently available.

Comments and remarks over classic linear loop-gain method for oscillator design and analysis. New proposed method based on NDF/RRT

Abstract. This paper describes a new and original method for designing oscillators based on the Normalized Determinant Function (NDF) and Return Relations (RRT)- Firstly, a review of the loop-gain method will be performed. The loop-gain method pros, cons and some examples for exploring wrong solutions provided by this method will be shown. This method produces in some cases wrong solutions because some necessary conditions have not been fulfilled. The required necessary conditions to assure a right solution will be described. The necessity of using the NDF or the Transpose Return Relations (RRT), which are related with the True Loop-Gain, to test the additional conditions will be demonstrated. To conclude this paper, the steps for oscillator design and analysis, using the proposed NDF/RRj method, will be presented. The loop-gain wrong solutions will be compared with the NDF/RRj and the accuracy of this method to estimate the oscillation frequency and QL will be demonstrated. Some additional examples of plane reference oscillators (Z/Y/T), will be added and they will be analyzed with the new NDF/RRj proposed method, even these oscillators cannot be analyzed using the classic loop gain method.

A proposed two-stage two-tether scientific mission at Jupiter

A two-stage mission to place a spacecraft (SC) below the Jovian radiation belts, using a spinning bare tether with plasma contactors at both ends to provide propulsion and power,is proposed. Capture by Lorentz drag on the tether, at the periapsis of a barely hyperbolic equatorial orbit, is followed by a sequence of orbits at near-constant periapsis, drag finally bringing the SC down to a circular orbit below the halo ring. Although increasing both tether heating and bowing, retrograde motion can substantially reduce accumulated dose as compared with prograde motion, at equal tether-to-SC mass ratio. In the second stage,the tether is cut to a segment one order of magnitude smaller, with a single plasma contactor, making the SC to slowly spiral inward over severalmonths while generating large onboard power, which would allow multiple scientific applications, including in situ study of Jovian grains, auroral sounding of upper atmosphere, and space- and time-resolved observations of surface and subsurface.

Transductor óptico-sonoro basado en procesado de imagen

En este proyecto se aborda la transducción óptico-sonora utilizando métodos de tratamiento digital de imagen. Para llevar a cabo el proyecto se consideran únicamente métodos de bajo presupuesto, por lo que para realizar todo el proceso de conversión óptico-sonora se utilizan un ordenador y un escáner doméstico. Como el principal objetivo del proyecto es comprobar si es viable utilizar el tratamiento digital de imagen como conversor no se ha contemplado la utilización de equipamiento profesional. La utilidad de este proyecto está en la restauración del sonido de material fílmico con importantes degradaciones, tales que no sea posible su reproducción en un proyector. Con el prototipo que se propone, realizado con el software de programación Matlab, se consigue digitalizar el audio analógico de las películas en malas condiciones ya que la captura de audio se efectúa de manera óptica sobre las bandas sonoras. Lo conseguido en este proyecto cobra especial importancia si se tiene en cuenta la cantidad de material cinematográfico que hay en películas de celulosa. La conservación de dicho material requiere unas condiciones de almacenamiento muy específicas para que el soporte no se vea afectado, pero con el paso del tiempo es habitual que las bobinas de película presenten deformaciones o incluso ruptura. Aplicando métodos de tratamiento digital de imagen es posible restaurar el audio de fragmentos de película que no puedan ser expuestos a la tensión producida por los rodillos de los proyectores, incluso es posible recuperar el audio de fotogramas concretos ya que la digitalización del audio se realiza capturando la imagen de la forma de onda. Por ello, el procedimiento seguido para digitalizar la película debe ser poco intrusivo para garantizar la conservación del soporte fílmico. Cabe destacar que en este proyecto se ha realizado la conversión óptico-sonora sobre las bandas de sonido analógicas de área variable presentes en la película, pero el procedimiento es aplicable también a las bandas de área variable realizando modificaciones en el prototipo. Esto último queda fuera del objetivo de este proyecto, pero puede ser un trabajo futuro. ABSTRACT This project addresses optical to sound conversion using digital image processing methods. To carry out the project are considered only low-budget methods , so for all optical to sound conversion process using a computer and a home scanner . As the main application of this project is to test the feasibility of using the digital image processing as a converter does not contemplate the use of professional equipment. The main objective of this project is the restoration of sound film material with significant impairments , such is not possible playback on a projector. With the proposed prototype , made with Matlab programming software , you get digitize analog audio bad movies because the audio capture is performed optically on the soundtracks. The achievements in this project is especially important if you consider the amount of film material is in cellulose films . The preservation of such material requires a very specific storage conditions to which the support is not affected , but over time it is common for film reels presenting deformations or even rupture. Applying methods of digital image processing is possible to restore the audio from movie clips that can not be exposed to the tension produced by the rollers of the projectors , it is even possible to retrieve specific frames audio and audio that digitization is done by capturing the image of the waveform. Therefore, the procedure used to digitize the film should be bit intrusive to ensure the conservation of the film medium. Note that in this project was carried out optical to sound conversion on analog variable area soundtracks present in the film, but the procedure is applicable to variable-area bands making changes to the prototype. The latter is beyond the scope of this project, but can be a future work.

Sistema de información geográfica Campus Sur UPM

El proyecto que he realizado ha consistido en la creación de un sistema de información geográfica para el Campus Sur UPM, que puede servir de referencia para su implantación en cualquier otro campus universitario. Esta idea surge de la necesidad por parte de los usuarios de un campus de disponer de una herramienta que les permita consultar la información de los distintos lugares y servicios del campus, haciendo especial hincapié en su localización geográfica. Para ello ha sido necesario estudiar las tecnologías actuales que permiten implementar un sistema de información geográfica, dando lugar al sistema propuesto, que consiste en un conjunto de medios informáticos (hardware y software), que van a permitir al personal del campus obtener la información y localización de los elementos del campus desde su móvil. Tras realizar un análisis de los requisitos y funcionalidades que debía tener el sistema, el proyecto ha consistido en el diseño e implementación de dicho sistema. La información a consultar estará almacenada y disponible para su consulta en un equipo servidor accesible para el personal del campus. Para ello, durante la realización del proyecto, ha sido necesario crear un modelo de datos basado en el campus y cargar los datos geográficos de utilidad en una base de datos. Todo esto ha sido realizado mediante el producto software Smallword Core 4.2. Además, ha sido también necesario desplegar un software servidor que permita a los usuarios consultar dichos datos desde sus móviles vía WIFI o Internet, el producto utilizado para este fin ha sido Smallworld Geospatial Server 4.2. Para la realización de las consultas se han utilizado los servicios WMS(Web Map Service) y WFS(Web Feature Service) definidos por el OGC(Open Geospatial Consortium). Estos servicios están adaptados para la consulta de información geográfica. El sistema también está compuesto por una aplicación para dispositivos móviles con sistema operativo Android, que permite a los usuarios del sistema consultar y visualizar la información geográfica del campus. Dicha aplicación ha sido diseñada y programada a lo largo de la realización del proyecto. Para la realización de este proyecto también ha sido necesario un estudio del presupuesto que supondría una implantación real del sistema y el mantenimiento que implicaría tener el sistema actualizado. Por último, el proyecto incluye una breve descripción de las tecnologías futuras que podrían mejorar las funcionalidades del sistema: la realidad aumentada y el posicionamiento en el interior de edificios. ABSTRACT. The project I've done has been to create a geographic information system for the Campus Sur UPM, which can serve as a reference for implementation in any other college campus. This idea arises from the need for the campus users to have a tool that allows them to view information from different places and services, with particular emphasis on their geographical location. It has been necessary to study the current technologies that allow implementing a geographic information system, leading to the proposed system, which consists of a set of computer resources (hardware and software) that will allow campus users to obtain information and location of campus components from their mobile phones. Following an analysis of the requirements and functionalities that the system should have, the project involved the design and implementation of the system . The information will be stored and available on a computer server accessible to campus users. Accordingly, during the project, it was necessary to create a data model based on campus data and load this data in a database. All this has been done by Smallword Core 4.2 software product. In addition, it has also been necessary to deploy a server software that allows users to query the data from their phones via WIFI or Internet, the product used for this purpose has been Smallworld Geospatial Server 4.2 . To carry out the consultations have used the services WMS (Web Map Service) and WFS (Web Feature Service) defined by the OGC (Open Geospatial Consortium). These services are tailored to the geographic information retrieval. The system also consists of an application for mobile devices with Android operating system, which allows users to query and display geographic information related to the campus. This application has been designed and programmed over the project. For the realization of this project has also been necessary to study the budget that would be a real system implementation and the maintenance that would have the system updated. Finally, the project includes a brief description of future technologies that could improve the system's functionality: augmented reality and positioning inside the buildings.

Optimal polygonal L1 linearization and fast interpolation of nonlinear systems

The analysis of complex nonlinear systems is often carried out using simpler piecewise linear representations of them. A principled and practical technique is proposed to linearize and evaluate arbitrary continuous nonlinear functions using polygonal (continuous piecewise linear) models under the L1 norm. A thorough error analysis is developed to guide an optimal design of two kinds of polygonal approximations in the asymptotic case of a large budget of evaluation subintervals N. The method allows the user to obtain the level of linearization (N) for a target approximation error and vice versa. It is suitable for, but not limited to, an efficient implementation in modern Graphics Processing Units (GPUs), allowing real-time performance of computationally demanding applications. The quality and efficiency of the technique has been measured in detail on two nonlinear functions that are widely used in many areas of scientific computing and are expensive to evaluate.

Neutronic analysis of the bi-spectral moderator such as that proposed for ESS

This paper reports on design studies concerning a moderator concept which aims to maximize the time averaged flux. The idea is to provide neutron spectra showing two clear maxima, with peaks at View the MathML source and View the MathML source arising from leakage from both cryogenic and thermal moderators. Such a concept known as a bi-spectral moderator (Mezei, 2006 [1]) while proven on a reactor source has only been examined for the ESS 2003 proposal. Filges et al. (2003 [2]), which featured a different design than the current ESS. This paper thus reports on a baseline design for such a moderator concept and shows that it can provide substantial gains in count rates for those applications not requiring high resolution in time-of-flight.

A proposed bare tether experiment on board a sounding rocket

A sounding rocket experiment is proposed to carry out two experiments by the conductive bare-tether; 1) the test of the OML (Orbital-Motion-Limited) theory to collect electron, and II) the test of techniques to determine (neutral) density profile in critical E-layer. The main driver of the mission is provide a space tether technology experiment in low-Earth-Orbit (LEO) deploying a long tape tether in space and verify the performance of the bare electrodynamic tape tether. The sounding rocket experiment will show no danger to other satellites as the tether missions YES1, SEDSAT, and ProCEDS, which is cancelled just for afraid of collision with the ISS orbit. Also, the sounding rocket mission is possible to demonstrate the bare tether technology in low cost, simple mission concept, fast realization for space structures. The present sounding rocket experiment is expected to be the first conductive bare tether experiment.

A proposed bare-tether experiment on board a sounding rocket

A mission on board a sounding rocket to carry out two bare-tether experiments is proposed: a test of orbital-motion-limited (OML) collection and the proof-of-flight of a technique to determine the (neutral) density vertical profile in the critical E-layer. Since full bias from the motional field will be small (~ 20V), corresponding to a tape 1 km long and V rocket <8 km/s, a power source with a range of supply voltages of few kV would be used. First, the negative terminal of the supply would be connected to the tape, and the positive terminal to a round, conductive boom of length 10 - 20 m; electrons collected by the boom cross the supply into the tape, where they leak out at the rate of ion impact plus secondary emission. Determination of the density profile from measurements of auroral emissions observed from the rocket, as secondaries racing down the magnetic field reach an E-layer footprint, are discussed. Next the positive terminal of the voltage supply is connected to the tape, and the negative terminal to a Hollow Cathode (HC); electrons now collected by the tape cross the supply, and are ejected at the HC. The opposite connections, with current collection operated by tape and boom, and operating on electrons and ions, and through partial switching in the supply, allow testing OML collection in almost all respects it depends on.

Planeamiento y políticas de vivienda en el área metropolitana de Madrid durante la democracia (1975-2007)

La tesis analiza la realidad residencial construida en los municipios del Área Metropolitana de Madrid durante la democracia, en términos de localización, cantidad y calidad/cualidad, y su relación con el desarrollo de las políticas de planeamiento y de vivienda. La pregunta central que ha guiado la investigación es la siguiente: ¿cómo han incidido los instrumentos de política de vivienda y de planeamiento urbanístico en el crecimiento residencial de los municipios del Área Metropolitana de Madrid? Se trata de poner en relación dos políticas públicas orientadas por la Administración en sus distintos niveles de actuación: una de carácter territorial, el planeamiento urbanístico -cuya ejecución es de competencia municipal-, y otra de carácter sectorial, las políticas de vivienda -definidas por la Administración Central y Autonómica-. Al considerar la política de vivienda como el resultado de la política financiera, la política fiscal y la política de suelo, se ha observado cómo en España las dos primeras suponen más del 70% de la intervención presupuestaria en vivienda. Esta investigación se ha centrado particularmente en la tercera, la política de suelo, por su vinculación directa con el planeamiento urbanístico, pero sin dejar de tener en cuenta las dos primeras, no sólo por su implicación en el gasto público, sino porque han tenido tanto efecto, o más, en la conformación de la ciudad como ha podido tenerlo el planeamiento. La primera parte de la tesis se centra en el estudio de las políticas, sus objetivos e instrumentos (normativos y de planificación), mientras que en la segunda parte se analiza la realidad construida, por medio de una serie de variables e indicadores relacionados con la producción residencial (suelo y viviendas); en la tercera se presenta la parte de análisis y las conclusiones generales. Al cruzar los objetivos y los instrumentos de ambas políticas se ha podido concluir con una propuesta de periodización evidenciando las ontinuidades, cambios o transformaciones: después de una etapa de transición –de 1975 a 1978, coincide con los años de la transición democrática, en el que se definen las bases de las nuevas políticas-, se han podido diferenciar tres períodos: 1979-1989, 1990-1997 y 1998-2007. El primer período corresponde a los años en los que se fue construyendo todo el aparato institucional regulador con las nuevas administraciones que surgieron de la democracia. El segundo período, aunque comenzó con la aprobación de la Ley del Suelo de 1990 como instrumento clave del planeamiento regulador, se caracterizó por el cuestionamiento del modelo intervencionista y por los primeros planteamientos de liberalización. Finalmente, en el tercer período se pusieron las bases normativas de la liberalización del suelo en España, con la reforma de la Ley del Suelo de 1998 y otras medidas “remediales”. Finalmente, se presenta el análisis de los resultados sobre la realidad construida, teniendo como clave de interpretación la periodización propuesta a partir de las políticas, con el propósito de conocer cómo han podido incidir en el crecimiento residencial del AMM. Por tanto, la tesis aborda la inquietud de cuándo, cómo y dónde las políticas públicas han construido ciudad y han generado barrios, pues también trata de analizar los espacios urbanos que han sido el resultado físico de dichas políticas (aspectos de los conjuntos residenciales, el entorno inmediato y su relación con el tejido urbano existente), y no sólo de mostrar cantidades de viviendas construidas. Posteriormente, el estudio se centra en el análisis de las actuaciones públicas sobre suelos destinados a uno de los llamados “usos débiles”, las viviendas protegidas. Éstas se han beneficiado, de una u otra manera, de las ayudas económicas que se incluyen en los planes de vivienda y, por ello, están sujetas a unos parámetros definidos por la normativa vigente en cada caso. Ha interesado realizar una valoración de las mismas a partir de criterios de integración social y funcional, y de equilibrio territorial. ABSTRACT The PhD thesis analyses the residential areas built in the Metropolitan Area of Madrid, in terms of location, quality and quantity, and the relationship to the resulting built environment planning and housing policies. Its cover a period of tree decades since the onset of democracy in Spain in 1975 up to the beginning of the great recession starting 2007. The central question that has guided the research is the following: how the instruments of housing policy and urban planning have influenced the residential growth of the municipalities of the Metropolitan Area of Madrid? It is about putting together two different public policies that are also carried out at different levels of government: spacial and urban planning –whose execution is under municipal jurisdiction under principles and guidelines defined at a regional scale; and the sectorial housing policies which are mostly defined by the Nacional and Regional governments and are very interlinked with the wider economic policies of the country. When considering housing policy as the result of financial, fiscal and land policy, it has been noted in Spain that instruments under the first two types of measures (financial and fiscal) account for over 70% of the housing budget intervention. This research has particularly focused on the third, Land Policy, because of its direct link to urban planning. Nevertheless, the research also considers f inancial and f iscal pol icies, not only because of thei r signi f icant level of publ ic spending, but al so because of thei r great impacto n shaping the way the ci ty is bui l t . The first part of the thesis focuses on the study of the policies, objectives and instruments (housing and planning), while the second part analyses the built reality by means of a number of variables and indicators related to the housing production (land and housing). In the third part the analysis and general conclusions are presented. After relating the objectives and instruments of both policies, the thesis concludes with a proposal for periodization showing continuities, changes and transformations: after a transition period – from 1975 to 1978 coinciding with the years of the democratic transition, in which the basis of the new policies were defined- tree periods (1979-1989, 1990- 1997 and 1998-2007) have been d i s t i n g u i s h e d . The first period covers the years in which a new institutional apparatus wa s b u i l t wi t h t h e n e w a r r a n g eme n t s t h a t eme r g e d from democracy. The second period, even though it began with the approval of the Land Act 1990 as key element of the regulatory planning, was characterized by the questioning of public intervention and early approaches to liberalization. Finally, in the third period, the normative basis of liberalization was set up in Spain, with the reform of the Land Act 1998 and other “corrective” measures. At a final point, the analisys of the results on the reality constructed is presented having as a key of interpretation the periodization proposed. This provides tools for interpreting how policies did affect residential growth in the Metropolitan Area of Madrid. Therefore, the thesis addresses the issues of when, how and where public policies have inf luenced and guided the development of resident ial áreas in the región dur ing this t ime f rame. I t is also concerned with analysing those urban spaces that have been the physical result of such policies (aspects of residential complexes, the immediate environment and its relationship with the existing urban infraestructure), going beyond the analisys of statistical data. Subsequently, the study focuses on the analysis of public actions on land for the so-called "weak uses" particularly social housing. These have benefited in one way or another, of financial assistance included in housing plans and, therefore, are subject to some parameters defined by the regulations in force in each case.

Energy Management and Optimization for Video Decoders based on Functional-oriented Reconfiguration

In recent years, the increasing sophistication of embedded multimedia systems and wireless communication technologies has promoted a widespread utilization of video streaming applications. It has been reported in 2013 that youngsters, aged between 13 and 24, spend around 16.7 hours a week watching online video through social media, business websites, and video streaming sites. Video applications have already been blended into people daily life. Traditionally, video streaming research has focused on performance improvement, namely throughput increase and response time reduction. However, most mobile devices are battery-powered, a technology that grows at a much slower pace than either multimedia or hardware developments. Since battery developments cannot satisfy expanding power demand of mobile devices, research interests on video applications technology has attracted more attention to achieve energy-efficient designs. How to efficiently use the limited battery energy budget becomes a major research challenge. In addition, next generation video standards impel to diversification and personalization. Therefore, it is desirable to have mechanisms to implement energy optimizations with greater flexibility and scalability. In this context, the main goal of this dissertation is to find an energy management and optimization mechanism to reduce the energy consumption of video decoders based on the idea of functional-oriented reconfiguration. System battery life is prolonged as the result of a trade-off between energy consumption and video quality. Functional-oriented reconfiguration takes advantage of the similarities among standards to build video decoders reconnecting existing functional units. If a feedback channel from the decoder to the encoder is available, the former can signal the latter changes in either the encoding parameters or the encoding algorithms for energy-saving adaption. The proposed energy optimization and management mechanism is carried out at the decoder end. This mechanism consists of an energy-aware manager, implemented as an additional block of the reconfiguration engine, an energy estimator, integrated into the decoder, and, if available, a feedback channel connected to the encoder end. The energy-aware manager checks the battery level, selects the new decoder description and signals to build a new decoder to the reconfiguration engine. It is worth noting that the analysis of the energy consumption is fundamental for the success of the energy management and optimization mechanism. In this thesis, an energy estimation method driven by platform event monitoring is proposed. In addition, an event filter is suggested to automate the selection of the most appropriate events that affect the energy consumption. At last, a detailed study on the influence of the training data on the model accuracy is presented. The modeling methodology of the energy estimator has been evaluated on different underlying platforms, single-core and multi-core, with different characteristics of workload. All the results show a good accuracy and low on-line computation overhead. The required modifications on the reconfiguration engine to implement the energy-aware manager have been assessed under different scenarios. The results indicate a possibility to lengthen the battery lifetime of the system in two different use-cases.

Formulación de incentivos óptimos y viables para la mejora de la seguridad vial en concesiones de carreteras

La evolución de los roles de la Administración y empresas en la prestación de servicios públicos, así como las crecientes restricciones presupuestarias para financiarlos, están propiciando una cada vez mayor utilización del sistema concesional para la financiación y gestión de carreteras. Ante esta situación, cabe cuestionarse si la regulación de las prestaciones a obtener se está introduciendo de forma adecuada en los contratos. Uno de los aspectos más relevantes en este sentido es el relacionado con la seguridad de la infraestructura, sobre el cual la empresa concesionaria tiene capacidad de actuación pero, en un sentido económico estricto, pocos incentivos para mejorarla. Todo ello a pesar de los elevados costes sociales derivados de la accidentalidad. Esta tesis analiza la idoneidad de los indicadores e incentivos de seguridad vial que se vienen aplicando en concesiones de carreteras, encontrándose una gran heterogeneidad e incluso incorrecciones técnicas en su formulación. Además se pone de manifiesto la poca vinculación que tienen con la estructura de costes y beneficios de las actuaciones de mejora de seguridad vial, por lo que su introducción en los contratos resulta anodina. Con el objeto de superar esta situación, en esta tesis se analizan en profundidad los aspectos que intervienen en la formulación de indicadores e incentivos de seguridad vial. De este análisis se deduce la ecuación que liga, por tipología de carretera, el beneficio social derivado del nivel de seguridad de la carretera y el coste para alcanzarlo. A través de esta ecuación se determina el nivel de seguridad óptimo desde el punto de vista económico‐social. La investigación continúa extrapolando métodos de la teoría microeconómica de incentivos al campo de las concesiones de carreteras, a fin de determinar la formulación del incentivo de seguridad vial teóricamente óptimo. Asimismo, la tesis toma en consideración la experiencia en la aplicación práctica de incentivos en concesiones vigentes, realizándose una propuesta para superar las controversias que se están produciendo actualmente en España. Además, se ha simulado la aplicación de la formulación propuesta a diversas concesiones con un doble objetivo: verificar la viabilidad económica de su aplicación y corroborar en qué medida se adecua mejor al óptimo económico‐social. Como resultado, se proponen un indicador y un incentivo concretos que inducen a las concesionarias a orientar su gestión hacia la consecución del nivel de seguridad vial óptimo desde el punto de vista económico‐social, todo ello dentro de un marco de viabilidad presupuestaria. Changes in the roles of Government and the Private Sector in the provision of public services along with the budget constraints to finance them are resulting in an increasing use of the concession system for financing and managing roads. Taking this into account, the question is whether the regulation of quality criteria is being properly introduced in the contracts or not. One of the most important aspects at this respect is the road safety. On the one hand, concessionaires are able to manage this aspect up to a point. On the other hand, from an strict economic point of view, they have little incentive to improve it, despite the high social costs of accidents. This thesis has analyzed the suitability of indicators and incentives usually introduced in road concession contracts, finding high heterogeneity, and even technical inaccuracies on their formulation. It has also been found the lack of connection between these incentives and the costs of measures to improve road safety, therefore they are not expected to fulfil their purpose. In order to overcome this situation, this thesis firstly analyzes in depth the issues involved in the development of road safety indicators and incentives. This analysis yields the equation which links the social benefit derived from the level of road safety and the cost to achieve it. In its turn, through this equation it is possible to meet the optimal road safety level from the socio‐economic point of view. Secondly, this thesis extrapolates microeconomic methods to the field of highway concessions, with the aim of determining the formulation of the optimal road safety incentive. Furthermore, the thesis takes into account the experience in the practical application of incentives on existing concessions, performing a proposal to settle the disputes between concessionaires and the Public Administrations. Finally, the thesis simulates the implementation of the proposed indicator and incentive to real concessions with the aim of verifying the economic feasibility of their application and confirming how they match the socio‐economic optimum. As a result, this thesis proposes an indicator and incentive that induce companies to drive the management of the concession towards achieving the optimal road safety level, all within a framework of the budgetary feasibility.

An Ant Colony System adaptation to deal with accessibility issues after a disaster

One of the main problems relief teams face after a natural or man-made disaster is how to plan rural road repair work tasks to take maximum advantage of the limited available financial and human resources. Previous research focused on speeding up repair work or on selecting the location of health centers to minimize transport times for injured citizens. In spite of the good results, this research does not take into account another key factor: survivor accessibility to resources. In this paper we account for the accessibility issue, that is, we maximize the number of survivors that reach the nearest regional center (cities where economic and social activity is concentrated) in a minimum time by planning which rural roads should be repaired given the available financial and human resources. This is a combinatorial problem since the number of connections between cities and regional centers grows exponentially with the problem size, and exact methods are no good for achieving an optimum solution. In order to solve the problem we propose using an Ant Colony System adaptation, which is based on ants? foraging behavior. Ants stochastically build minimal paths to regional centers and decide if damaged roads are repaired on the basis of pheromone levels, accessibility heuristic information and the available budget. The proposed algorithm is illustrated by means of an example regarding the 2010 Haiti earthquake, and its performance is compared with another metaheuristic, GRASP.