Homography-based ground plane detection using a single on-board camera

This study presents a robust method for ground plane detection in vision-based systems with a non-stationary camera. The proposed method is based on the reliable estimation of the homography between ground planes in successive images. This homography is computed using a feature matching approach, which in contrast to classical approaches to on-board motion estimation does not require explicit ego-motion calculation. As opposed to it, a novel homography calculation method based on a linear estimation framework is presented. This framework provides predictions of the ground plane transformation matrix that are dynamically updated with new measurements. The method is specially suited for challenging environments, in particular traffic scenarios, in which the information is scarce and the homography computed from the images is usually inaccurate or erroneous. The proposed estimation framework is able to remove erroneous measurements and to correct those that are inaccurate, hence producing a reliable homography estimate at each instant. It is based on the evaluation of the difference between the predicted and the observed transformations, measured according to the spectral norm of the associated matrix of differences. Moreover, an example is provided on how to use the information extracted from ground plane estimation to achieve object detection and tracking. The method has been successfully demonstrated for the detection of moving vehicles in traffic environments.

Analysis of frame-compatible subsampling structures for efficient 3DTV broadcast

The evolution of the television market is led by 3DTV technology, and this tendency can accelerate during the next years according to expert forecasts. However, 3DTV delivery by broadcast networks is not currently developed enough, and acts as a bottleneck for the complete deployment of the technology. Thus, increasing interest is dedicated to ste-reo 3DTV formats compatible with current HDTV video equipment and infrastructure, as they may greatly encourage 3D acceptance. In this paper, different subsampling schemes for HDTV compatible transmission of both progressive and interlaced stereo 3DTV are studied and compared. The frequency characteristics and preserved frequency content of each scheme are analyzed, and a simple interpolation filter is specially designed. Finally, the advantages and disadvantages of the different schemes and filters are evaluated through quality testing on several progressive and interlaced video sequences.

Selective area growth of a- and c-plane GaN nanocolumns by molecular beam epitaxy using colloidal nanolithography

Selective area growth of a-plane GaN nanocolumns by molecular beam epitaxy was performed for the first time on a-plane GaN templates. Ti masks with 150 nm diameter nanoholes were fabricated by colloidal lithography, an easy, fast and cheap process capable to handle large areas. Even though colloidal lithography does not provide a perfect geometrical arrangement like e-beam lithography, it produces a very homogeneous mask in terms of nanohole diameter and density, and is used here for the first time for the selective area growth of GaN. Selective area growth of a-plane GaN nanocolumns is compared, in terms of anisotropic lateral and vertical growth rates, with GaN nanocolumns grown selectively on the c-plane

Single phase a-plane MgZnO epilayers for UV optoelectronics: substitutional behaviour of Mg at large contents

High quality 1 μm thick a-plane MgxZn1−xO layers were produced by molecular beam epitaxy with Mg contents higher than 50%. Resonant Rutherford backscattering spectrometry combined with ion channeling revealed a uniform growth in both composition and atomic order. The lattice-site location of Mg, Zn and O elements was determined independently, proving the substitutional behaviour of Mg in Zn-sites of the wurtzite lattice. X-Ray diffraction pole figure analysis also confirms the absence of phase separation. Optical properties at such high Mg contents were studied in Schottky photodiodes.

Portal Observatorio: El nuevo punto de encuentro de la comunidad IDE

El Portal Observatorio IDE es una plataforma colaborativa online en desarrollo que aspira a convertirse en un destacado punto de encuentro para toda la comunidad IDE. Nace con el fin de conseguir atraer las diversas iniciativas relacionadas con las IDE que se están gestando en la actualidad, contribuyendo así a la concentración, coordinación y monitorización de esfuerzos. Para conseguirlo, se propone una plataforma con una estructura adaptable y dinámica, en la que se invite a los propios usuarios a colaborar en la gestión de su estructura, funcionamiento y alojamiento de contenidos. En el presente artículo se realiza una declaración de los fundamentos e ideas que han llevado a las instituciones implicadas a la creación del Portal Observatorio IDE, se detallan las herramientas tecnológicas empleadas para su programación, las características y utilidades implementadas y los resultados esperados con su puesta en marcha.

Failure locus of polypropylene nonwoven fabrics under in-plane biaxial deformation

The failure locus, the characteristics of the stress–strain curve and the damage localization patterns were analyzed in a polypropylene nonwoven fabric under in-plane biaxial deformation. The analysis was carried out by means of a homogenization model developed within the context of the finite element method. It provides the constitutive response for a mesodomain of the fabric corresponding to the area associated to a finite element and takes into account the main deformation and damage mechanisms experimentally observed. It was found that the failure locus in the stress space was accurately predicted by the Von Mises criterion and failure took place by the localization of damage into a crack perpendicular to the main loading axis.

A constitutive model for the in-plane mechanical behavior of nonwoven fabrics

A constitutive model is presented for the in-plane mechanical behavior of nonwoven fabrics. The model is developed within the context of the finite element method and provides the constitutive response for a mesodomain of the fabric corresponding to the area associated to a finite element. The model is built upon the ensemble of three blocks, namely fabric, fibers and damage. The continuum tensorial formulation of the fabric response rigorously takes into account the effect of fiber rotation for large strains and includes the nonlinear fiber behavior. In addition, the various damage mechanisms experimentally observed (bond and fiber fracture, interfiber friction and fiber pull-out) are included in a phenomenological way and the random nature of these materials is also taken into account by means of a Monte Carlo lottery to determine the damage thresholds. The model results are validated with recent experimental results on the tensile response of smooth and notched specimens of a polypropylene nonwoven fabric.

Deep levels in a-plane, high Mg-content MgxZn1-xO epitaxial layers grown by molecular beam epitaxy

Deep level defects in n-type unintentionally doped a-plane MgxZn1−xO, grown by molecular beam epitaxy on r-plane sapphire were fully characterized using deep level optical spectroscopy (DLOS) and related methods. Four compositions of MgxZn1−xO were examined with x = 0.31, 0.44, 0.52, and 0.56 together with a control ZnO sample. DLOS measurements revealed the presence of five deep levels in each Mg-containing sample, having energy levels of Ec − 1.4 eV, 2.1 eV, 2.6 V, and Ev + 0.3 eV and 0.6 eV. For all Mg compositions, the activation energies of the first three states were constant with respect to the conduction band edge, whereas the latter two revealed constant activation energies with respect to the valence band edge. In contrast to the ternary materials, only three levels, at Ec − 2.1 eV, Ev + 0.3 eV, and 0.6 eV, were observed for the ZnO control sample in this systematically grown series of samples. Substantially higher concentrations of the deep levels at Ev + 0.3 eV and Ec − 2.1 eV were observed in ZnO compared to the Mg alloyed samples. Moreover, there is a general invariance of trap concentration of the Ev + 0.3 eV and 0.6 eV levels on Mg content, while at least and order of magnitude dependency of the Ec − 1.4 eV and Ec − 2.6 eV levels in Mg alloyed samples.

A canonical UTD solution for electromagnetic scattering by an electrically large impedance circular cylinder illuminated by an obliquely incident plane wave

A uniform geometrical theory of diffraction (UTD) solution is developed for the canonical problem of the electromagnetic (EM) scattering by an electrically large circular cylinder with a uniform impedance boundary condition (IBC), when it is illuminated by an obliquely incident high frequency plane wave. A solution to this canonical problem is first constructed in terms of an exact formulation involving a radially propagating eigenfunction expansion. The latter is converted into a circumferentially propagating eigenfunction expansion suited for large cylinders, via the Watson transform, which is expressed as an integral that is subsequently evaluated asymptotically, for high frequencies, in a uniform manner. The resulting solution is then expressed in the desired UTD ray form. This solution is uniform in the sense that it has the important property that it remains continuous across the transition region on either side of the surface shadow boundary. Outside the shadow boundary transition region it recovers the purely ray optical incident and reflected ray fields on the deep lit side of the shadow boundary and to the modal surface diffracted ray fields on the deep shadow side. The scattered field is seen to have a cross-polarized component due to the coupling between the TEz and TMz waves (where z is the cylinder axis) resulting from the IBC. Such cross-polarization vanishes for normal incidence on the cylinder, and also in the deep lit region for oblique incidence where it properly reduces to the geometrical optics (GO) or ray optical solution. This UTD solution is shown to be very accurate by a numerical comparison with an exact reference solution.

Shaking table tests of a RC frame structure equipped with hysteretic dampers

This paper provides partial results of an on-going research aimed at investigating the seismic response of reinforced concrete (RC) frames equipped with hysteretic-type energy dissipating devices (EDD). From a prototype RC frame structure designed only for gravity loads, a test model scaled in geometry to 2/5 was defined and built in the Laboratory of Structures of the University of Granada. Four EDDs were installed in the test model to provide the same seismic resistance than a conventional RC bare frame designed for sustain gravity and seismic loads following current codes. The test model with EDDs was subjected to several seismic simulations with the shaking table of Laboratory of structures of the University of Granada. The test results provide empirical evidences on the efficiency of the EDDs to prevent damage on the main frame and concentrating the inelastic deformations on the EDDs.

Optimización y propuesta de sistema opaco de cerramiento multicapa ligero con estructura de light steel frame como alternativa competitiva a los sistemas de cerramientos tradicionales

En la actualidad, el crecimiento de la población y el desarrollo tecnológico de nuestros tiempos han originado novedosas formas de confort para los habitantes, lo cual a su vez se traduce en una demanda creciente de energía. No obstante, el concepto energético está llegando a la conciencia y es necesario adaptarse a la nueva situación, por lo tanto, es imprescindible el estudio y el aprovechamiento de nuevos sistemas constructivos de cerramientos, como pueden ser los cerramientos multicapas ligeros, que presentan características favorables para el ahorro en el consumo energético, y a su vez pueden ser industrializados, obteniendo beneficios, como la mejora de la calidad, el acortamiento de plazos constructivos, mayor seguridad, altas prestaciones, mayor ligereza, más espacio habitable, entre otros. El desarrollo de esta tesis doctoral esta centrado en definir tres propuestas de Cerramientos Multicapas Ligeros (CML) con estructura de light steel frame, analizando el comportamiento térmico y acústico, así como también el coste económico de las mismas, con el objetivo de demostrar que este tipo de sistema constructivo es una alternativa competitiva a los sistemas de Cerramientos Tradicionales y, que a su vez se puedan implementar en cualquier sistema constructivo y se puedan adaptar a los distintos ambientes climáticos que existen en España. Por otro lado, se han seleccionado tres Cerramientos Tradicionales, para llevar a cabo las distintas comparativas propuestas. La investigación se desarrolla en cinco grandes partes: La primera parte está formada por la justificación de la investigación y el planteamiento de los objetivos, así como también la hipótesis de partida y la metodología empleada. En la segunda parte se definen los antecedentes teóricos, divididos en tres temas: el cerramiento ? la fachada, la transmisión del calor y la transmisión del sonido en los cerramientos. También se realiza una síntesis del trabajo de investigación previo que he realizado ?Caracterización del comportamiento térmico de fachadas multicapas ligeras?, el cual sirve de base de partida para el desarrollo de esta tesis. Y por último, se desarrollan distintos temas relacionados con el Light Steel Frame (LSF), en donde se lleva a cabo una búsqueda de la documentación disponible sobre las investigaciones científico-tecnológicas, desde distintos puntos de vista: térmico, acústico, económico, estructural, en caso de incendio, industrialización y medioambiental ? sostenibilidad. Una vez realizados todos los puntos anteriores y para sintetizar la información, se lleva a cabo una clasificación de los sistemas de cerramientos que tienen como estructura el light steel frame, se analizan las ventajas e inconvenientes de cada uno de estos sistemas de la clasificación, llegando a unas conclusiones que sirven de base para definir las propuestas de Cerramientos Multicapas Ligeros. En la tercera parte, se definen los tres cerramientos tradicionales que se utilizan para realizar las comparativas con los cerramientos multicapas ligeros, definiendo las características de cada uno de los materiales y, también se desarrollan los criterios de diseño que deben cumplir los cerramientos multicapas ligeros, definiendo cada una de las tres muestras de ensayo de cerramientos multicapas ligeros. En la cuarta parte se lleva a cabo el análisis teórico ? experimental de las seis muestras de estudio, en donde, se realiza una investigación térmica basada en simulaciones y experimentaciones en células de ensayo e implementación de la termografía infrarroja. Por otro lado, se realiza también una investigación acústica desarrollando ensayos en laboratorio de aislamiento a ruido aéreo e intensimetría sonora. Y por último, se hace un análisis económico, tomando en cuenta las variables del coste de construcción, el consumo energético, el ahorro que supone la masa a la estructura y el espacio adicional que aporta este tipo de sistema constructivo a la superficie útil, para ello se plantean distintos escenarios de estudio. Una vez obtenidos los resultados de las diferentes investigaciones (térmica, acústica y económica), se llevan a cabo una serie de comparativas entre los cerramientos multicapas ligeros y los cerramientos tradicionales, y los cerramientos multicapas ligeros entre sí. En la quinta parte, se exponen las conclusiones derivadas de las distintas investigaciones y se realiza la comprobación de los objetivos propuestos y de la hipótesis de partida, destacando los hallazgos principales para cada situación y se presentan las líneas futuras de investigación que han ido surgiendo en el desarrollo de la tesis doctoral.

Discrimination of AE Signals From Friction and Concrete Cracking in a Reinforced Concrete Frame Subjected to Seismic Trainings

This paper shows the preliminary results of the development and application of a procedure to filter the Acoustic Emission (AE) signals to distinguish between AE signals coming from friction and AE signals coming from concrete cracking. These signals were recorded during the trainings of an experiment carried out on a reinforced concrete frame subjected to dynamic loadings with the shaking table of the University of Granada (Spain). Discrimination between friction and cracking AE signals is the base to develop a successful procedure and damage index based on AE testing for health monitoring of RC structures subjected to earthquakes.

AFRICA BUILD Portal: developing a social network of African health researchers and educators

One of the main outputs of the project is a collaborative platform which integrates a myriad of research and learning resources. This article presents the first prototype of this platform: the AFRICA BUILD Portal (ABP 1.0). The ABP is a Web 2.0 platform which facilitates the access, in a collaborative manner, to these resources. Through a usable web interface, the ABP has been designed to avoid, as much as possible, the connectivity problems of African institutions. In this paper, we suggest that the access to complex systems does not imply slow response rates, and that their development model guides the project to a natural technological transfer, adaptation and user acceptance. Finally, this platform aims to motivate research attitudes during the learning process and stimulate user?s collaborations.

A new UTD for the electromagnetic plane wave scattering by a canonical circular cylinder with an impedance boundary condition

A UTD solution is developed for describing the scattering by a circular cylinder with an impedance boundary condition (IBC), when it is illuminated by an obliquely incident electromagnetic (EM) plane wave. The solution to this canonical problem will be crucial for the construction of a more general UTD solution valid for an arbitrary smooth convex surface with an IBC, when it is illuminated by an arbitrary EM ray optical field. The canonical solution is uniformly valid across the surface shadow boundary that is tangent to the surface at grazing incidence. This canonical solution contains cross polarized terms in the scattered fields, which arise from a coupling of the TEz and TMz waves at the impedance boundary on the cylinder. Here, z is the cylinder axis. Numerical results show very good accuracy for the simpler and efficient UTD solution, when compared to exact but very slowly convergent eigenfunction solution.

A formalism and method for representing and reasoning with process models authored by subject matter experts

Enabling Subject Matter Experts (SMEs) to formulate knowledge without the intervention of Knowledge Engineers (KEs) requires providing SMEs with methods and tools that abstract the underlying knowledge representation and allow them to focus on modeling activities. Bridging the gap between SME-authored models and their representation is challenging, especially in the case of complex knowledge types like processes, where aspects like frame management, data, and control flow need to be addressed. In this paper, we describe how SME-authored process models can be provided with an operational semantics and grounded in a knowledge representation language like F-logic in order to support process-related reasoning. The main results of this work include a formalism for process representation and a mechanism for automatically translating process diagrams into executable code following such formalism. From all the process models authored by SMEs during evaluation 82% were well-formed, all of which executed correctly. Additionally, the two optimizations applied to the code generation mechanism produced a performance improvement at reasoning time of 25% and 30% with respect to the base case, respectively.