Lifetime improvement after phosphorous diffusion gettering on upgraded metallurgical grade silicon

Wide experimental evidence of the phosphorus diffusion gettering beneficial effect on solar grade silicon is found by measuring electron effective lifetime and interstitial iron concentration in as-grown and post processed samples from two ingots of upgraded metallurgical grade silicon produced by Ferrosolar. Results after two different P-diffusion processes are compared: P emitter diffusion at 850ºC followed by fast cool-down (called “standard process”) or followed by slow cool-down (called “extended process”). It is shown that final lifetimes of this low cost material are in the range of those obtained with conventional material. The extended process can be beneficial for wafers with specific initial distribution and concentration of iron, e.g. materials with high concentration of big Fe precipitates, while for other cases the standard process is enough efficient. An analysis based on the comparison of measured lifetime and dissolved iron concentration with theoretical calculations helps to infer the initial iron distribution and concentration, and according to that, choose the more effective type of gettering.

Si(100) versus Ge(100): Watching the interface formation for the growth of III-V-based solar cells on abundant substrates

We investigated the atomic surface properties of differently prepared silicon and germanium (100) surfaces during metal-organic vapour phase epitaxy/chemical vapour deposition (MOVPE/MOCVD), in particular the impact of the MOVPE ambient, and applied reflectance anisotropy/difference spectroscopy (RAS/RDS) in our MOVPE reactor to in-situ watch and control the preparation on the atomic length scale for subsequent III-V-nucleation. The technological interest in the predominant opto-electronic properties of III-V-compounds drives the research for their heteroepitaxial integration on more abundant and cheaper standard substrates such as Si(100) or Ge(100). In these cases, a general task must be accomplished successfully, i.e. the growth of polar materials on non-polar substrates and, beyond that, very specific variations such as the individual interface formation and the atomic step structure, have to be controlled. Above all, the method of choice to grow industrial relevant high-performance device structures is MOVPE, not normally compatible with surface and interface sensitive characterization tools, which are commonly based on ultrahigh vacuum (UHV) ambients. A dedicated sample transfer system from MOVPE environment to UHV enabled us to benchmark the optical in-situ spectra with results from various surfaces science instruments without considering disruptive contaminants. X-ray photoelectron spectroscopy (XPS) provided direct observation of different terminations such as arsenic and phosphorous and verified oxide removal under various specific process parameters. Absorption lines in Fourier-transform infrared (FTIR) spectra were used to identify specific stretch modes of coupled hydrides and the polarization dependence of the anti-symmetric stretch modes distinguished different dimer orientations. Scanning tunnelling microscopy (STM) studied the atomic arrangement of dimers and steps and tip-induced H-desorption proved the saturation of dangling bonds after preparati- n. In-situ RAS was employed to display details transiently such as the presence of H on the surface at lower temperatures (T <; 800°C) and the absence of Si-H bonds at elevated annealing temperature and also surface terminations. Ge buffer growth by the use of GeH4 enables the preparation of smooth surfaces and leads to a more pronounced amplitude of the features in the spectra which indicates improvements of the surface quality.

ARXPS analysis of a GaAs/GaInP heterointerface with application in III-V multijunction solar cells

In this contribution, angle-resolved X-ray photoelectron spectroscopy is used to explore the extension and nature of a GaAs/GaInP heterointerface. This bilayer structure constitutes a very common interface in a multilayered III-V solar cell. Our results show a wide indium penetration into the GaAs layer, while phosphorous diffusion is much less important. The physico-chemical nature of such interface and its depth could deleteriously impact the solar cell performance. Our results probe the formation of spurious phases which may profoundly affect the interface behavior.

In situ control of the GE(100)surface domain structure for III-V multijunction solar cells

Vicinal Ge(100) is the common substrate for state of the art multi-junction solar cells grown by metal-organic vapor phase epitaxy (MOVPE). While triple junction solar cells based on Ge(100) present efficiencies mayor que 40%, little is known about the microscopic III-V/Ge(100) nucleation and its interface formation. A suitable Ge(100) surface preparation prior to heteroepitaxy is crucial to achieve low defect densities in the III-V epilayers. Formation of single domain surfaces with double layer steps is required to avoid anti-phase domains in the III-V films. The step formation processes in MOVPE environment strongly depends on the major process parameters such as substrate temperature, H2 partial pressure, group V precursors [1], and reactor conditions. Detailed investigation of these processes on the Ge(100) surface by ultrahigh vacuum (UHV) based standard surface science tools are complicated due to the presence of H2 process gas. However, in situ surface characterization by reflection anisotropy spectroscopy (RAS) allowed us to study the MOVPE preparation of Ge(100) surfaces directly in dependence on the relevant process parameters [2, 3, 4]. A contamination free MOVPE to UHV transfer system [5] enabled correlation of the RA spectra to results from UHV-based surface science tools. In this paper, we established the characteristic RA spectra of vicinal Ge(100) surfaces terminated with monohydrides, arsenic and phosphorous. RAS enabled in situ control of oxide removal, H2 interaction and domain formation during MOVPE preparation.

Optimización de la aplicación de lodos de depuración de aguas residuales al abonado o mejora de suelos

El objetivo de este trabajo de investigación fue evaluar el efecto de la aplicación de lodos residuales procedentes de una planta de tratamiento de aguas residuales acondicionados como biosólido para el abonado de tres cultivos agrícolas. Esto se realizó a través del estudio de las variables de producción (desarrollo vegetal de cada cultivo) y de la comparación de las características de los suelos utilizados antes y después de los ensayos experimentales. A través de la investigación se confirmó la mejora en la calidad del suelo y mejor rendimiento de cultivo debido a los biosólidos procedentes de tratamiento de aguas residuales. Este trabajo de investigación de tipo descriptivo y experimental, utilizó lodos optimizados que fueron aplicados a tres cultivos agrícolas de ciclo corto. Fueron evaluados dos cultivos (sandía y tomate) bajo riego y un cultivo (arroz) en secano. En la primera fase del trabajo se realizó la caracterización de los lodos, para ellos se realizaron pruebas físico químicas y microbiológicas. Fue utilizado el método de determinación de metales por espectrometría de emisión atómica de plasma acoplado inductivamente, (ICP-AES) para conocer las concentraciones de metales. La caracterización microbiológica para coliformes totales y fecales se realizó utilizando la técnica del Número más probable (NMP), y para la identificación de organismos patógenos se utilizó el método microbiológico propuesto por Kornacki & Johnson (2001), que se fundamenta en dos procesos: pruebas presuntivas y prueba confirmativa. Tanto los resultados para la determinación de metales y elementos potencialmente tóxicos; como las pruebas para la determinación de microorganismos potencialmente peligrosos, estuvieron por debajo de los límites considerados peligrosos establecidos por la normativa vigente en Panama (Reglamento Técnico COPANIT 47-2000). Una vez establecido la caracterización de los lodos, se evalúo el potencial de nutrientes (macro y micro) presentes en los biosólidos para su potencial de uso como abono en cultivos agrícolas. El secado de lodos fue realizado a través de una era de secado, donde los lodos fueron deshidratados hasta alcanzar una textura pastosa. “La pasta de lodo” fue transportada al área de los ensayos de campo para continuar el proceso de secado y molida. Tres ensayos experimentales fueron diseñados al azar con cinco tratamientos y cuatro repeticiones para cada uno de los tres cultivos: sandía, tomate, arroz, en parcelas de 10m2 (sandía y tomate) y 20 m2 (arroz) para cada tratamiento. Tres diferentes dosis de biosólidos fueron evaluadas y comparadas con un tratamiento de fertilizante comercial y un tratamiento control. La dosis de fertilizante comercial utilizada en cada cultivo fue la recomendada por el Instituto de Investigación Agropecuaria de Panamá. Los ensayos consideraron la caracterización inicial del suelo, la preparación del suelo, semilla, y arreglo topográfico de los cultivos siguiendo las recomendaciones agronómicas de manejo de cultivo establecida por el Instituto de Investigación Agropecuaria. Para los ensayos de sandía y tomate se instaló el sistema de riego por goteo. Se determinaron los ácidos húmicos presentes en los cultivos, y se estudiaron las variables de desarrollo de cada cultivo (fructificación, cosecha, peso de la cosecha, dimensiones de tamaño y color de las frutas, rendimiento, y la relación costo – rendimiento). También se estudiaron las variaciones de los macro y micro nutrientes y las variaciones de pH, textura de suelo y MO disponible al inicio y al final de cada uno de los ensayos de campo. Todas las variables y covariables fueron analizadas utilizando el programa estadístico INFOSAT (software para análisis estadístico de aplicación general) mediante el análisis de varianza, el método de comparaciones múltiples propuesto por Fisher (LSD Fisher) para comparar las medias de los cultivares y el coeficiente de correlación de Pearson que nos permite analizar si existe una asociación lineal entre dos variables. En la evaluación de los aportes del biosólido a los cultivos se observó que los macronutrientes N y P se encontraban de los límites requeridos en cada uno de los cultivos, pero que los niveles de K estuvieron por debajo de los requerimientos de los cultivos. A nivel de la fertilización tradicional con fertilizante químico se observó que la dosis recomendada para cada uno de los cultivos del estudio estaba sobreestimada en los tres principales macronutrientes: Nitrógeno, Fosforo y Potasio. Contenían concentraciones superiores de N, P y K a las requeridas teóricamente por el cultivo. El nutriente que se aporta en exceso es el Fósforo. Encontramos que para el cultivo de sandía era 18 veces mayor a lo requerido por el cultivo, en tomate fue 12 veces mayor y en el cultivo de arroz, 34 veces mayor. El fertilizante comercial tuvo una influencia en el peso final y rendimiento final en cada uno de los cultivos del estudio. A diferencia, los biosólidos tuvieron una influencia directa en el desarrollo de los cultivos (germinación, coloración, tamaño, longitud, diámetro, floración y resistencia a enfermedades). Para el caso de la sandía la dosis de biosólido más cercana al óptimo para el cultivo es la mayor dosis aplicada en este ensayo (97.2 gramos de biosólido por planta). En el caso de tomate, el fertilizante comercial obtuvo los mejores valores, pero las diferencias son mínimas con relación al tratamiento T1, de menor dosis de biosólido (16.2 gramos de biosólido por planta). Los resultados generales del ensayo de tomate estuvieron por debajo del rendimiento esperado para el cultivo. Los tratamientos de aplicación de biosólidos aportaron al desarrollo del cultivo en las variables tamaño, color y resistencia a las enfermedades dentro del cultivo de tomate. Al igual que el tomate, en el caso del arroz, el tratamiento comercial obtuvo los mejores resultados. Los resultados finales de peso y rendimiento del cultivo indican que el tratamiento (T2), menor dosis de biosólido (32.4 gramos por parcela), no tuvo diferencias significativas con los resultados obtenidos en las parcelas con aplicación de fertilizante comercial (T1). El tratamiento T4 (mayor dosis de biosólido) obtuvo los mejores valores para las variables germinación, ahijamiento y espigamiento del cultivo, pero al momento de la maduración obtuvo los menores resultados. Los biosólidos aportan nutrientes a los cultivos y al final del ensayo se observó que permanecen disponibles en el suelo, aportando a la mejora del suelo final. En los tres ensayos, se pudo comprobar que los aportes de los biosólidos en el desarrollo vegetativo de los cultivos. También se encontró en todos los ensayos que no hubo diferencias significativas (p > 0.05) entre los tratamientos de biosólidos y fertilizante comercial. Para obtener mejores resultados en estos tres ensayos se requeriría que a la composición de biosólidos (utilizada en este ensayo) se le adicione Potasio, Calcio y Magnesio en las cantidades requeridas por cada uno de los cultivos. ABSTRACT The objective of this investigation was to evaluate the effect of residual sewage sludge obtained from the residual water of a treatment plant conditioned as Biosolid used on three reliable agricultural crops. The effect of the added sewage sludge was evaluated through the measurement of production variables such as crop plant development and the comparison of the soil characteristics used before and after the experimental tests. This investigation confirmed that biosolids from wastewater treatment can contribute to the growth of these crops. In this experimental approach, optimized sludge was applied to three short-cycle crops including two low-risk crops (watermelon and tomato) and one high-risk crop (rice) all grown on dry land. In the first phase of work, the characteristics of the sludge were assessed using chemical, physical and microbiological tests. The concentrations of metals were determined by atomic emission spectrometry inductively coupled plasma, (ICP-AES). Microbiological characterization was performed measuring total coliform and fecal count using the most probable number technique (NMP) and microbiological pathogens were identified using Kornacki & Johnson (2001) method based on two processes: presumptive and confirmatory tests. Both the results for the determination of metals and potentially toxic elements, as testing for the determination of potentially dangerous microorganisms were below the limits established by the applicable standard in Panama (Technical Regulate COPANIT 47-2000). After the metal and bacterial characterization of the sludge, the presence of macro or micronutrients in biosolids was measured to evaluate its potential for use as fertilizer in the growth of agricultural crops. The sludge was dehydrated via a drying process into a muddy slurry. The pulp slurry was transported to the field trial area to continue the process of drying and grinding. Three randomized experimental trials were designed to test with five treatment regimens and four replications for each of the crops: watermelon, tomato, rice. The five treatment regimens evaluated were three different doses of bio solid with commercial fertilizer treatment control and no fertilizer treatment control. Treatment areas for the watermelon and tomato were 10m2 plots land and for rice was 20m2. The amount of commercial fertilizer used to treat each crop was based on the amount recommended by Agricultural Research Institute of Panama. The experimental trials considered initial characterization of soil, soil preparation, seed, and crop topographical arrangement following agronomic crop management recommendations. For the tests evaluating the growth of watermelons and tomatoes and drip irrigation system was installed. The amount of humic acids present in the culture were determined and developmental variable of each crop were studied (fruiting crop harvest weight, size dimensions and color of the fruit, performance and cost effectiveness). Changes in macro and micronutrients and changes in pH, soil texture and OM available were measured at the beginning and end of each field trial. All variables and covariates were analyzed using INFOSAT statistical program (software for statistical analysis of general application) by analysis of variance, multiple comparisons method as proposed by Fisher (LSD Fisher) to compare the means of cultivars and the Pearson ratio that allows us to analyze if there is a linear association between two variables. In evaluating the contribution of biosolids to agricultural crops, the study determined that the macronutrients N & P were within the requirements of crops, but K levels were below the requirements of crops. In terms of traditional chemical fertilizer fertilization, we observed that the recommended dose for each study crop was overestimated for the three major nutrients: nitrogen, phosphorus and potassium. Higher concentrations containing N, P and K to the theoretically required by the crop. The recommended dose of commercial fertilizer for crops study contained greater amounts of phosphorus, crops that need. The level of phosphorous was found to be18 times greater than was required for the cultivation of watermelon; 12 times higher than required for tomato, and 34 times higher than required for rice cultivation. Phosphorus inputs of commercial fertilizer were a primary influence on the weight and performance of each crop. Unlike biosolids had a direct influence on crop development (germination, color, size, length, diameter, flowering and disease resistance). In the case of growth of watermelons, the Biosolid dose closest to the optimum for cultivation was applied the highest dose in this assay (97.2 grams of bio solids per plant). In the case of tomatoes, commercial fertilizer had the best values but the differences were minimal when compared to treatment T1, the lower dose of sewage sludge (Biosolid 16.2 grams per plant). The overall results for the tomato crop yield of the trial were lower than expected. Additionally, the application of biosolids treatment contributed to the development of fruit of variable size, color and disease resistance in the tomato crops. Similar to the tomato crop, commercial fertilizer treatment provided the best results for the rice crop. The final results of weight and crop yield for rice indicated that treatment with T2 amount of biosolids (34.2 grams per plot) was not significantly different from the result obtained in the application plot given commercial fertilizer (T1). The T4 (higher dose of bio solid) treatment had the best values for the germination, tillering and bolting variables of the rice crop but for fruit ripening yielded lower results. In all three trials, biosolids demonstrated the ability to contribute in the vegetative growth of crops. It was also found in all test no significant differences (p>0.05) between treatment of bio solid and commercial fertilizer. Biosolids provided nutrients to the crops and even at the end of the trial remained available in the ground soil, contributing to the improvement of the final ground. The best results from these three trials is that the use of bio solids such as those used in this assay would require the addition of potassium, calcium and magnesium in quantities required for each crop.