Understanding the selective area growth of GaN nanocolumns by MBE using Ti nanomasks

The influence of the substrate temperature, III/V flux ratio, and mask geometry on the selective area growth of GaN nanocolumns is investigated. For a given set of growth conditions, the mask design (diameter and pitch of the nanoholes) is found to be crucial to achieve selective growth within the nanoholes. The local III/V flux ratio within these nanoholes is a key factor that can be tuned, either by modifying the growth conditions or the mask geometry. On the other hand, some specific growth conditions may lead to selective growth but not be suitable for subsequent vertical growth. With optimized conditions, ordered GaN nanocolumns can be grown with a wide variety of diameters. In this work, ordered GaN nanocolumns with diameter as small as 50 nm are shown.

Materials Research for HiPER Laser Fusion Facilities: Chamber Wall, Structural Material and Final Optics

The European HiPER project aims to demonstrate commercial viability of inertial fusion energy within the following two decades. This goal requires an extensive Research &Development program on materials for different applications (e.g., first wall, structural components and final optics). In this paper we will discuss our activities in the framework of HiPER to develop materials studies for the different areas of interest. The chamber first wall will have to withstand explosions of at least 100 MJ at a repetition rate of 5-10 Hz. If direct drive targets are used, a dry wall chamber operated in vacuum is preferable. In this situation the major threat for the wall stems from ions. For reasonably low chamber radius (5-10 m) new materials based on W and C are being investigated, e.g., engineered surfaces and nanostructured materials. Structural materials will be subject to high fluxes of neutrons leading to deleterious effects, such as, swelling. Low activation advanced steels as well as new nanostructured materials are being investigated. The final optics lenses will not survive the extreme ion irradiation pulses originated in the explosions. Therefore, mitigation strategies are being investigated. In addition, efforts are being carried out in understanding optimized conditions to minimize the loss of optical properties by neutron and gamma irradiation

Movimiento de paredes de dominio magnético en nanohilos con defectos controlados

La investigación realizada en este trabajo de tesis se ha centrado en el estudio de la generación, anclaje y desenganche de paredes de dominio magnético en nanohilos de permalloy con defectos controlados. Las últimas tecnologías de nanofabricación han abierto importantes líneas de investigación centradas en el estudio del movimiento de paredes de dominio magnético, gracias a su potencial aplicación en memorias magnéticas del futuro. En el 2004, Stuart Parkin de IBM introdujo un concepto innovador, el dispositivo “Racetrack”, basado en un nanohilo ferromagnético donde los dominios de imanación representan los "bits" de información. La frontera entre dominios, ie pared magnética, se moverían en una situación ideal por medio de transferencia de espín de una corriente polarizada. Se anclan en determinadas posiciones gracias a pequeños defectos o constricciones de tamaño nanométrico fabricados por litografía electrónica. El éxito de esta idea se basa en la generación, anclaje y desenganche de las paredes de dominio de forma controlada y repetitiva, tanto para la lectura como para la escritura de los bits de información. Slonczewski en 1994 muestra que la corriente polarizada de espín puede transferir momento magnético a la imanación local y así mover paredes por transferencia de espín y no por el campo creado por la corriente. Desde entonces muchos grupos de investigación de todo el mundo trabajan en optimizar las condiciones de transferencia de espín para mover paredes de dominio. La fracción de electrones polarizados que viaja en un hilo ferromagnético es considerablemente pequeña, así hoy por hoy la corriente necesaria para mover una pared magnética por transferencia de espín es superior a 1 107 A/cm2. Una densidad de corriente tan elevada no sólo tiene como consecuencia una importante degradación del dispositivo sino también se observan importantes efectos relacionados con el calentamiento por efecto Joule inducido por la corriente. Otro de los problemas científico - tecnológicos a resolver es la diversidad de paredes de dominio magnético ancladas en el defecto. Los diferentes tipos de pared anclados en el defecto, su quiralidad o el campo o corriente necesarios para desenganchar la pared pueden variar dependiendo si el defecto posee dimensiones ligeramente diferentes o si la pared se ancla con un método distinto. Además, existe una componente estocástica presente tanto en la nucleación como en el proceso de anclaje y desenganche que por un lado puede ser debido a la naturaleza de la pared que viaja por el hilo a una determinada temperatura distinta de cero, así como a defectos inevitables en el proceso de fabricación. Esto constituye un gran inconveniente dado que según el tipo de pared es necesario aplicar distintos valores de corriente y/o campo para desenganchar la pared del defecto. Como se menciona anteriormente, para realizar de forma eficaz la lectura y escritura de los bits de información, es necesaria la inyección, anclaje y desenganche forma controlada y repetitiva. Esto implica generar, anclar y desenganchar las paredes de dominio siempre en las mismas condiciones, ie siempre a la misma corriente o campo aplicado. Por ello, en el primer capítulo de resultados de esta tesis estudiamos el anclaje y desenganche de paredes de dominio en defectos de seis formas distintas, cada uno, de dos profundidades diferentes. Hemos realizado un análisis estadístico en diferentes hilos, donde hemos estudiado la probabilidad de anclaje cada tipo de defecto y la dispersión en el valor de campo magnético aplicado necesario para desenganchar la pared. Luego, continuamos con el estudio de la nucleación de las paredes de dominio magnético con pulsos de corriente a través una linea adyacente al nanohilo. Estudiamos defectos de tres formas distintas e identificamos, en función del valor de campo magnético aplicado, los distintos tipos de paredes de dominio anclados en cada uno de ellos. Además, con la ayuda de este método de inyección que es rápido y eficaz, hemos sido capaces de generar y anclar un único tipo de pared minimizando el comportamiento estocástico de la pared mencionado anteriormente. En estas condiciones óptimas, hemos estudiado el desenganche de las paredes de dominio por medio de corriente polarizada en espín, donde hemos conseguido desenganchar la pared de forma controlada y repetitiva siempre para los mismos valores de corriente y campo magnético aplicados. Además, aplicando pulsos de corriente en distintas direcciones, estudiamos en base a su diferencia, la contribución térmica debido al efecto Joule. Los resultados obtenidos representan un importante avance hacia la explotación práctica de este tipo de dispositivos. ABSTRACT The research activity of this thesis was focused on the nucleation, pinning and depinning of magnetic domain walls (DWs) in notched permalloy nanowires. The access to nanofabrication techniques has boosted the number of applications based on magnetic domain walls (DWs) like memory devices. In 2004, Stuart Parkin at IBM, conceived an innovative concept, the “racetrack memory” based on a ferromagnetic nanowire were the magnetic domains constitute the “bits” of information. The frontier between those magnetic domains, ie magnetic domain wall, will move ideally assisted by a spin polarized current. DWs will pin at certain positions due to artificially created pinning sites or “notches” fabricated with ebeam lithography. The success of this idea relies on the careful and predictable control on DW nucleation and a defined pinning-depinning process in order to read and write the bits of information. Sloncsewski in 1994 shows that a spin polarized current can transfer magnetic moment to the local magnetization to move the DWs instead of the magnetic field created by the current. Since then many research groups worldwide have been working on optimizing the conditions for the current induced DW motion due to the spin transfer effect. The fraction of spin polarized electrons traveling through a ferromagnetic nanowire is considerably small, so nowadays the current density required to move a DW by STT exceeds 1 107 A/cm2. A high current density not only can produce a significant degradation of the device but also important effects related to Joule heating were also observed . There are other scientific and technological issues to solve regarding the diversity of DWs states pinned at the notch. The types of DWs pinned, their chirality or their characteristic depinning current or field, may change if the notch has slightly different dimensions, the stripe has different thickness or even if the DW is pinned by a different procedure. Additionally, there is a stochastic component in both the injection of the DW and in its pinning-depinning process, which may be partly intrinsic to the nature of the travelling DW at a non-zero temperature and partly due to the unavoidable defects introduced during the nano-fabrication process. This constitutes an important inconvenient because depending on the DW type different values of current of magnetic field need to be applied in order to depin a DW from the notch. As mentioned earlier, in order to write and read the bits of information accurately, a controlled reproducible and predictable pinning- depinning process is required. This implies to nucleate, pin and depin always at the same applied magnetic field or current. Therefore, in the first chapter of this thesis we studied the pinning and depinning of DW in six different notch shapes and two depths. An statistical analysis was conducted in order to determine which notch type performed best in terms of pinning probability and the dispersion measured in the magnetic field necessary to depin the magnetic DWs. Then, we continued studying the nucleation of DWs with nanosecond current pulses by an adjacent conductive stripe. We studied the conditions for DW injection that allow a selective pinning of the different types of DWs in Permalloy nanostripes with 3 different notch shapes. Furthermore, with this injection method, which has proven to be fast and reliable, we manage to nucleate only one type of DW avoiding its stochastic behavior mentioned earlier. Having achieved this optimized conditions we studied current induced depinning where we also achieved a controlled and reproducible depinning process at always the same applied current and magnetic field. Additionally, changing the pulse polarity we studied the joule heating contribution in a current induced depinning process. The results obtained represent an important step towards the practical exploitation of these devices.

Induction of through-thickness compressive residual stress fields in thin Al2024-T351 plates by laser shock processing

Laser Shock Processing (LSP) has been demonstrated as an emerging technique for the induction of RS’s fields in subsurface layers of relatively thick specimens. However, the LSP treatment of relatively thin specimens brings, as an additional consequence, the possible bending in a process of laser shock forming. This effect poses a new class of problems regarding the attainment of specified RS’s depth profiles in the mentioned type of sheets, and, what can be more critical, an overall deformation of the treated component. The analysis of the problem of LSP treatment for induction of tentatively through-thickness RS’s fields for fatigue life enhancement in relatively thin sheets in a way compatible with reduced overall workpiece deformation due to spring-back self-equilibration is envisaged in this paper. The coupled theoretical-experimental predictive approach developed by the authors has been applied to the specification of LSP treatments for achievement of RS's fields tentatively able to retard crack propagation on normalized specimens. A convergence between numerical code results and experimental results coming from direct RS's measurement is presented as a first step for the treatment of the normalized specimens under optimized conditions and verification of the crack retardation properties virtually induced.

Optimized algorithms for the incremental analysis of logic programs

Global analysis of logic programs can be performed effectively by the use of one of several existing efficient algorithms. However, the traditional global analysis scheme in which all the program code is known in advance and no previous analysis information is available is unsatisfactory in many situations. Incrementa! analysis of logic programs has been shown to be feasible and much more efficient in certain contexts than traditional (non-incremental) global analysis. However, incremental analysis poses additional requirements on the fixpoint algorithm used. In this work we identify these requirements, present an important class of strategies meeting the requirements, present sufficient a priori conditions for such strategies, and propose, implement, and evalúate experimentally a novel algorithm for incremental analysis based on these ideas. The experimental results show that the proposed algorithm performs very efficiently in the incremental case while being comparable to (and, in some cases, considerably better than) other state-of-the-art analysis algorithms even for the non-incremental case. We argüe that our discussions, results, and experiments also shed light on some of the many tradeoffs involved in the design of algorithms for logic program analysis.

Aerodynamic shape optimization of the nose of a high-speed train subjected to crosswind conditions

When dealing with the design of a high-speed train, a multiobjective shape optimization problem is formulated, as these vehicles are object of many aerodynamic problems which are known to be in conflict. More mobility involves an increase in both the cruise speed and lightness, and these requirements directly influence the stability and the ride comfort of the passengers when the train is subjected to a side wind. Thus, crosswind stability plays a more relevant role among the aerodynamic objectives to be optimized. An extensive research activity is observed on aerodynamic response in crosswind conditions.