Modulation instability-induced fading in phase-sensitive optical time-domain reflectometry

Phase-sensitive optical time-domain reflectometry (?OTDR) is a simple and effective tool allowing the distributed monitoring of vibrations along single-mode fibers. We show in this Letter that modulation instability (MI) can induce a position-dependent signal fading in long-range ?OTDR over conventional optical fibers. This fading leads to a complete masking of the interference signal recorded at certain positions and therefore to a sensitivity loss at these positions. We illustrate this effect both theoretically and experimentally. While this effect is detrimental in the context of distributed vibration analysis using ?OTDR, we also believe that the technique provides a clear and insightful way to evidence the Fermi?Pasta?Ulam recurrence associated with the MI process.

Periodic time-domain modulation for the electrically tunable control of optical pulse train envelope and repetition rate multiplication

An electrically tunable system for the control of optical pulse sequences is proposed and demonstrated. It is based on the use of an electrooptic modulator for periodic phase modulation followed by a dispersive device to obtain the temporal Talbot effect. The proposed configuration allows for repetition rate multiplication with different multiplication factors and with the simultaneous control of the pulse train envelope by simply changing the electrical signal driving the modulator. Simulated and experimental results for an input optical pulse train of 10 GHz are shown for different multiplication factors and envelope shapes.

Models for Internal Quality Fruit Sorting, Based on Time- Domain Laser Reflectance Spectroscopy (TDRS)

Time domain laser reflectance spectroscopy (TDRS) was applied for the first time to evaluate internal fruit quality. This technique, known in medicine-related knowledge areas, has not been used before in agricultural or food research. It allows the simultaneous non-destructive measuring of two optical characteristics of the tissues: light scattering and absorption. Models to measure firmness, sugar & acid contents in kiwifruit, tomato, apple, peach, nectarine and other fruits were built using sequential statistical techniques: principal component analysis, multiple stepwise linear regression, clustering and discriminant analysis. Consistent correlations were established between the two parameters measured with TDRS, i.e. absorption & transport scattering coefficients, with chemical constituents (sugars and acids) and firmness, respectively. Classification models were built to sort fruits into three quality grades, according to their firmness, soluble solids and acidity.

Models for internal quality sorting of fruit, based on time-domain laser reflectance spectroscopy (TDRS).

Non-destructive measurement of fruit quality has been an important objective through recent years (Abbott, 1999). Near infrared spectroscopy (NIR) is applicable to the cuantification of chemicals in foods and NIK "laser spectroscopy" can be used to estimate the firmness of fruits. However, die main limitation of current optical techniques that measure light transmission is that they do not account for the coupling between absorption and scattering inside the tissue, when quantifying the intensity o f reemitted light. The solution o f this l i m i t a t i o n was the goal o f the present work.

Modeling the evolution of item rating networks using time-domain preferential attachment

The understanding of the structure and dynamics of the intricate network of connections among people that consumes products through Internet appears as an extremely useful asset in order to study emergent properties related to social behavior. This knowledge could be useful, for example, to improve the performance of personal recommendation algorithms. In this contribution, we analyzed five-year records of movie-rating transactions provided by Netflix, a movie rental platform where users rate movies from an online catalog. This dataset can be studied as a bipartite user-item network whose structure evolves in time. Even though several topological properties from subsets of this bipartite network have been reported with a model that combines random and preferential attachment mechanisms [Beguerisse Díaz et al., 2010], there are still many aspects worth to be explored, as they are connected to relevant phenomena underlying the evolution of the network. In this work, we test the hypothesis that bursty human behavior is essential in order to describe how a bipartite user-item network evolves in time. To that end, we propose a novel model that combines, for user nodes, a network growth prescription based on a preferential attachment mechanism acting not only in the topological domain (i.e. based on node degrees) but also in time domain. In the case of items, the model mixes degree preferential attachment and random selection. With these ingredients, the model is not only able to reproduce the asymptotic degree distribution, but also shows an excellent agreement with the Netflix data in several time-dependent topological properties.

Time domain passivity control for delayed teleoperation

La telepesencia combina diferentes modalidades sensoriales, incluyendo, entre otras, la visual y la del tacto, para producir una sensación de presencia remota en el operador. Un elemento clave en la implementación de sistemas de telepresencia para permitir una telemanipulación del entorno remoto es el retorno de fuerza. Durante una telemanipulación, la energía mecánica es transferida entre el operador humano y el entorno remoto. En general, la energía es una propiedad de los objetos físicos, fundamental en su mutual interacción. En esta interacción, la energía se puede transmitir entre los objetos, puede cambiar de forma pero no puede crearse ni destruirse. En esta tesis, se aplica este principio fundamental para derivar un nuevo método de control bilateral que permite el diseño de sistemas de teleoperación estables para cualquier arquitectura concebible. El razonamiento parte del hecho de que la energía mecánica insertada por el operador humano en el sistema debe transferirse hacia el entorno remoto y viceversa. Tal como se verá, el uso de la energía como variable de control permite un tratamiento más general del sistema que el control convencional basado en variables específicas del sistema. Mediante el concepto de Red de Potencia de Retardo Temporal (RPRT), el problema de definir los flujos de energía en un sistema de teleoperación es solucionado con independencia de la arquitectura de comunicación. Como se verá, los retardos temporales son la principal causa de generación de energía virtual. Este hecho se observa con retardos a partir de 1 milisegundo. Esta energía virtual es añadida al sistema de forma intrínseca y representa la causa principal de inestabilidad. Se demuestra que las RPRTs son transportadoras de la energía deseada intercambiada entre maestro y esclavo pero a la vez generadoras de energía virtual debido al retardo temporal. Una vez estas redes son identificadas, el método de Control de Pasividad en el Dominio Temporal para RPRTs se propone como mecanismo de control para asegurar la pasividad del sistema, y as__ la estabilidad. El método se basa en el simple hecho de que esta energía virtual debido al retardo debe transformarse en disipación. As__ el sistema se aproxima al sistema deseado, donde solo la energía insertada desde un extremo es transferida hacia el otro. El sistema resultante presenta dos cualidades: por un lado la estabilidad del sistema queda garantizada con independencia de la arquitectura del sistema y del canal de comunicación; por el otro, el rendimiento es maximizado en términos de fidelidad de transmisión energética. Los métodos propuestos se sustentan con sistemas experimentales con diferentes arquitecturas de control y retardos entre 2 y 900 ms. La tesis concluye con un experimento que incluye una comunicación espacial basada en el satélite geoestacionario ASTRA. ABSTRACT Telepresence combines different sensorial modalities, including vision and touch, to produce a feeling of being present in a remote location. The key element to successfully implement a telepresence system and thus to allow telemanipulation of a remote environment is force feedback. In a telemanipulation, mechanical energy must convey from the human operator to the manipulated object found in the remote environment. In general, energy is a property of all physical objects, fundamental to their mutual interactions in which the energy can be transferred among the objects and can change form but cannot be created or destroyed. In this thesis, we exploit this fundamental principle to derive a novel bilateral control mechanism that allows designing stable teleoperation systems with any conceivable communication architecture. The rationale starts from the fact that the mechanical energy injected by a human operator into the system must be conveyed to the remote environment and Vice Versa. As will be seen, setting energy as the control variable allows a more general treatment of the controlled system in contrast to the more conventional control of specific systems variables. Through the Time Delay Power Network (TDPN) concept, the issue of defining the energy flows involved in a teleoperation system is solved with independence of the communication architecture. In particular, communication time delays are found to be a source of virtual energy. This fact is observed with delays starting from 1 millisecond. Since this energy is added, the resulting teleoperation system can be non-passive and thus become unstable. The Time Delay Power Networks are found to be carriers of the desired exchanged energy but also generators of virtual energy due to the time delay. Once these networks are identified, the Time Domain Passivity Control approach for TDPNs is proposed as a control mechanism to ensure system passivity and therefore, system stability. The proposed method is based on the simple fact that this intrinsically added energy due to the communication must be transformed into dissipation. Then the system becomes closer to the ambitioned one, where only the energy injected from one end of the system is conveyed to the other one. The resulting system presents two benefits: On one hand, system stability is guaranteed through passivity independently from the chosen control architecture and communication channel; on the other, performance is maximized in terms of energy transfer faithfulness. The proposed methods are sustained with a set of experimental implementations using different control architectures and communication delays ranging from 2 to 900 milliseconds. An experiment that includes a communication Space link based on the geostationary satellite ASTRA concludes this thesis.

A time-domain finite element method for seakeeping and wave resistance problems

El objetivo de la tesis es la investigación de algoritmos numéricos para el desarrollo de herramientas numéricas para la simulación de problemas tanto de comportamiento en la mar como de resistencia al avance de buques y estructuras flotantes. La primera herramienta desarrollada resuelve el problema de difracción y radiación de olas. Se basan en el método de los elementos finitos (MEF) para la resolución de la ecuación de Laplace, así como en esquemas basados en MEF, integración a lo largo de líneas de corriente, y en diferencias finitas desarrollados para la condición de superficie libre. Se han desarrollado herramientas numéricas para la resolución de la dinámica de sólido rígido en sistemas multicuerpos con ligaduras. Estas herramientas han sido integradas junto con la herramienta de resolución de olas difractadas y radiadas para la resolución de problemas de interacción de cuerpos con olas. También se han diseñado algoritmos de acoplamientos con otras herramientas numéricas para la resolución de problemas multifísica. En particular, se han realizado acoplamientos con una herramienta numérica basada de cálculo de estructuras con MEF para problemas de interacción fluido-estructura, otra de cálculo de líneas de fondeo, y con una herramienta numérica de cálculo de flujos en tanques internos para problemas acoplados de comportamiento en la mar con “sloshing”. Se han realizado simulaciones numéricas para la validación y verificación de los algoritmos desarrollados, así como para el análisis de diferentes casos de estudio con aplicaciones diversas en los campos de la ingeniería naval, oceánica, y energías renovables marinas. ABSTRACT The objective of this thesis is the research on numerical algorithms to develop numerical tools to simulate seakeeping problems as well as wave resistance problems of ships and floating structures. The first tool developed is a wave diffraction-radiation solver. It is based on the finite element method (FEM) in order to solve the Laplace equation, as well as numerical schemes based on FEM, streamline integration, and finite difference method tailored for solving the free surface boundary condition. It has been developed numerical tools to solve solid body dynamics of multibody systems with body links across them. This tool has been integrated with the wave diffraction-radiation solver to solve wave-body interaction problems. Also it has been tailored coupling algorithms with other numerical tools in order to solve multi-physics problems. In particular, it has been performed coupling with a MEF structural solver to solve fluid-structure interaction problems, with a mooring solver, and with a solver capable of simulating internal flows in tanks to solve couple seakeeping-sloshing problems. Numerical simulations have been carried out to validate and verify the developed algorithms, as well as to analyze case studies in the areas of marine engineering, offshore engineering, and offshore renewable energy.

Estudio teórico y simulación de un OTDR para sistemas de comunicaciones por fibra óptica

El reflectómetro óptico en el dominio del tiempo, conocido por sus siglas en inglés como OTDR, es un dispositivo muy utilizado en sistemas de comunicaciones por fibra óptica para conocer de una manera rápida y sencilla como varía la potencia óptica a lo largo de la fibra óptica, siendo otro de sus usos frecuentes la localización de fallos y roturas en un enlace. Este proyecto fin de carrera, consiste en la realización mediante Matlab de una interfaz gráfica que permite simular un OTDR para distintos tipos de fibras, conectores y empalmes visualizándose por pantalla la variación de la potencia óptica en función de la distancia, pudiendo ampliar cualquier tramo del enlace que se desee visualizar con mayor detalle. Los objetivos del proyecto podemos establecerlos en dos partes. Primero, realizar una interfaz que nos permita diseñar un enlace de fibra óptica de forma sencilla, permitiendo además medir desde la atenuación de la fibra a la de un empalme. En segundo lugar, emplear la interfaz desarrollada para comprobar conceptos teóricos, haciendo hincapié en los principales errores de un enlace de fibra óptica real. Para una mejor visualización y concepción de lo implementado, es necesario revisar los principios básicos de funcionamiento de la fibra óptica y las principales características de un enlace, así como, los distintos dispositivos que lo componen, para después explicar el funcionamiento del OTDR y sus usos; por ello, en los capítulos segundo y tercero, se explican estas nociones básicas, necesarias para un mejor entendimiento del proyecto. Para poder utilizar la interfaz gráfica de usuario, el capítulo cuarto muestra la descripción de las funciones con parámetros, así como el manual de usuario de la interfaz gráfica. En el capítulo quinto se hace una recopilación y estudios de resultados para distintas simulaciones comprobando desde casos sencillos a casos extremos en los que se debe prestar una especial atención a los elementos que componen el enlace, siendo finalmente, en el sexto capítulo donde se presentan distintas conclusiones así como posibles trabajos futuros, a partir de lo realizado. ABSTRACT. The optical time domain reflectometer, known as OTDR, is a widely used device in systems for fiber optic communications used to know quick and simply how the optical power its varying along the fiber, with particular emphasis to another of its frequent uses in troubleshooting on a link. This final project consists in carrying through a graphical interface in Matlab to simulate an OTDR for different types of fibers, connectors and splices, visualizing the variation of optical power as a function of the distance. It is possible to zoom in specific sections to view them with greater detail. The project objectives can be set in two parts: - Make an interface that allows us to design a fiber optic link easily and measuring from the fiber attenuation to a splice one. - Use the interface developed to test theoretical concepts, emphasizing the most important mistakes of a real optical fiber link. For better visualization and understanding of what it’s been implemented, it is necessary to review the basic operating principles of fiber optics and the main characteristics of a fiber link, and also the different types of devices that comprise it, and then explaining also how the OTDR works and its uses, therefore, in second and third chapters, explains these basics needed for a better understanding of the project. To use the GUI, the fourth chapter shows the description of the functions with parameters and the user manual of the GUI. The fifth chapter is a compilation and study of some simulation results for simple cases to check from simply to extreme cases putting special attention to the elements that make up the link. To sum up, in the sixth chapter will appear different conclusions and possible future works for improving the graphical interface or making a new one.

Aplicación de distintas metodologías a la monitorización de la humedad del suelo y al cálculo del balance hídrico diario

Dada la importancia de conocer la humedad del suelo de forma precisa y en tiempo real, se ha realizado este trabajo de investigación cuyo objetivo principal ha sido seleccionar un Balance Hídrico del Suelo (BHS) diario y validar sus estimaciones de humedad del suelo frente a medidas obtenidas “in situ”, aplicándolo a tres emplazamientos seleccionados en la zona centro con características edáficas y climáticas diferentes, y de este modo estimar con cierta precisión la humedad del suelo como Agua Disponible (AD) para las plantas y a su vez permitir la realización de estudios climáticos. Los observatorios meteorológicos seleccionados fueron: Guadalajara/El Serranillo en la zona aluvial del río Henares; Colmenar Viejo/Base Famet en la rampa sur del Guadarrama sobre rocas metamórficas; y Radiosondeo/Madrid(Barajas) en arenas arcósicas de grano grueso. Se realizó una caracterización morfológica y un estudio de las propiedades físicas, químicas e hidrofísicas de los suelos en cada emplazamiento. El suelo de Guadalajara, Xerorthent Típico presenta una secuencia genética de horizontes (Ap-AC-C1-C2) siendo su clase textural entre franco-arenosa a franca, con menos del 2% de elementos gruesos, presencia de caliza a lo largo de todo el perfil, destacando la homogeneidad en vertical y horizontal de sus propiedades. El suelo de Colmenar, Xerorthent Dystrico, presenta una secuencia genética de horizontes (A-C-C/R) apareciendo el horizonte C/R entre 20-30 cm; y la roca aproximadamente a unos 30 cm; destacando en este perfil su acidez y el alto contenido de elementos gruesos. El suelo de Radiosondeo, Haploxeralf Típico, presenta la secuencia normal de horizontes de los alfisoles (A-Bt1-Bt2-C/Bt); destacando su heterogeneidad principalmente en el plano horizontal, con presencia del Bt a diferentes profundidades en un corto espacio longitudinal. En una primera fase de experimentación (2007-2008) se seleccionaron BHS diarios que sólo utilizaban como datos de entrada la información de variables meteorológicas y el valor del Agua Disponible Total (ADT) para cada tipo de suelo y profundidad. Se probaron BHS diarios con agotamiento exponencial y directo de la reserva, utilizando la evapotranspiración de referencia de Penman-Monteith recomendada por FAO. Al mismo tiempo que se disponía de los datos estimados de humedad de suelo mediante diferentes BHS diarios en los tres emplazamientos, también se realizó una monitorización de la humedad del suelo “in situ” mediante el método gravimétrico, con adaptación de dicha metodología a la problemática de cada suelo, para determinar en cada fecha tanto la humedad del suelo como su contenido de AD para una profundidad de 0 a 30 cm. Se tomaron en cada fecha de muestreo 5 muestras para la profundidad 0- 10 cm, otras cinco para 10-20 cm y otras cinco para 20-30 cm, realizándose el correspondiente tratamiento estadístico de los datos. El ADT se calculó a partir de los datos de capacidad de campo y punto de marchitez obtenidos en laboratorio con membrana de Richards. Los resultados de esta primera fase permitieron conocer que el BHS exponencial diario era el que mejor estimaba el AD en Guadalajara considerando la capacidad de campo a una presión de 33 kPa, mientras que en Colmenar se debían considerar para un mejor ajuste, 10 kPa en lugar de 33 kPa. En el observatorio de Radiosondeo debido a que en cada fecha de muestreo la profundidad en la que aparecía el horizonte Bt era diferente, no se pudo demostrar si el BHS exponencial diario tenía un buen comportamiento. En una segunda fase de experimentación (2009-2012) y con el objeto de aminorar los problemas encontrados en Radiosondeo para la medida de humedad del suelo por el método gravimétrico, se procedió a la instalación y utilización de diferentes sensores de medida de humedad de suelo en el mismo observatorio: TDR (time domain reflectometry - TRIME T3 de IMKO); FDR capacitivo (frecuency domain reflectometry - ECH2O EC-20 de DECAGON) y otros. Esta segunda fase de experimentación tuvo una duración de 4 años y se compararon las medidas de humedad de suelo obtenidas a partir de los sensores con las estimadas del BHS exponencial hasta una profundidad de 0 a 85 cm. En laboratorio se realizaron calibraciones específicas de los sensores TDR y FDR para cada uno de los horizontes más diferenciados del Haploxeralf Típico, utilizando diferentes tipos de regresión. Los valores de humedad de suelo con el equipo TDR, corregidos mediante la calibración específica de laboratorio, fueron los que más se ajustaron a las medidas realizadas por método gravimétrico “in situ”, por lo que se utilizó el TDR para las comparaciones con los valores obtenidos del BHS exponencial diario durante los cuatro años de esta segunda fase experimental. Se realizaron diferentes estimaciones del ADT, partiendo de datos de laboratorio y/o de datos procedentes de humedad de los sensores en campo. Los resultados mostraron de nuevo la conveniencia de utilizar el BHS exponencial diario, pero en este caso, con la estimación del ADT realizada a partir de las gráficas de los sensores. Mediante la utilización de los datos de humedad del BHS exponencial diario se han realizado comparaciones con el mismo tipo de balance pero utilizando un periodo semanal o mensual en lugar de diario, para conocer las diferencias. Los valores obtenidos con periodicidad mensual han dado valores de AD inferiores a los balances calculados semanalmente o diariamente. Por último se ha comprobado que los resultados de un BHS exponencial diario pueden complementar la información que se obtiene del Índice de Precipitación Estandarizado (SPI) y pueden mejorar el estudio de la sequía agrícola. ABSTRACT Due to the importance of a better knowledge of soil water at real time and in a more precisely way, this research work has being carried out with the main objective of selecting a daily Soil Water Balance (SWB) to estimate soil water content, and validate it in comparison to “in situ” measurements. Three locations, differing in soil and climate characteristics, were selected in central Spain in order to estimate with certain acuity soil water as plant-Available Water (AW) and to serve as a tool for the climatic studies. The selected places near meteorology stations were: Guadalajara/El Serranillo an alluvium of the Henares watershed; Colmenar Viejo/Base Famet, in the south raised area of the Guadarrama river basin, over metamorphic rocks; and Radiosondeo/Madrid (Barajas) in coarse arkosic sandstone. Morphology characterization, physical, chemical and hydrologic soil properties were studied in each area. In Guadalajara the soil is a Typic Xerorthent with a (Ap-AC-C1- C2) genetic horizon sequence, loam-sandy to loam textural class, less than 2% of rock fragments, presence of equivalent CaCO3 through the whole profile, outstanding the vertical and horizontal homogeneity of the properties. In Colmenar the soil is represented by a Dystric Xerorthent with a (A-C-C/R) genetic horizon sequence, the C/R is 20-30 cm deep where rock outcrops are approximately at 30 cm; a characteristic feature of this profile is its high acidity and high rock fragments content. In Radiosondeo the soil is represented by a Typic Haploxeralf, with the usual alfisol genetic horizon sequence (A-Bt1-Bt2-C/Bt); outstanding its horizontal heterogeneity, “the variability of the Bt (clay enriched horizon) depth in short distances”. In a first experimental stage (2007-2008), the daily SWB chosen was that which only uses as input data the information from the meteorology variables and plant-Total Available Water (TAW) for each soil type and depth. Different daily SWB (with exponential or direct plant-Available Water depletion) were applied, using the Penman- Monteith reference evapotranspiration (ETo) recommended by FAO. At the same time as soil water content was estimated from the different daily SWB at the three locations, also soil water content was being monitored by “in situ” gravimetric methodology, adapting it to each soil characteristic, to determine every time soil water content and AW to a depth of 0 to 30 cm. In each sampling date, 5 samples for each depth were taken: 0-10 cm; 10-20 cm and 20-30 cm and the data were submitted to the corresponding statistical analysis. The TAW was calculated based on field capacity (FC) and permanent wilting point (PWP) data obtained from laboratory by the Richards pressure plate. Results from this first experimental stage show that the daily exponential SWB was the one which better estimated the AW in Guadalajara considering field capacity at -33 kPa, though in Colmenar, field capacity at -10 kPa must be considered instead of -33 kPa for a better estimation. In Radiosondeo due to the fact that the Bt horizon depth varied in different sampling dates, it could not be established if the daily exponential SWB had a good performance. In a second experimental stage (20019-2012) and with the objective of minimizing the problems encountered in Radiosondeo for measuring “in situ” soil water content by the gravimetric method, the installation of different sensors for measuring soil water content were established and used in the same field location: TDR (time domain reflectometry - TRIME T3 from IMKO), capacitance FDR (frecuency domain reflectometry - ECH2O EC-20 from DECAGON) and others. This second experimental stage lasted 4 years in order to compare the soil water measures from the sensors with the estimations by the exponential SWB form 0 to 85 cm soil depths. At laboratory, specific calibrations for TDR and FDR sensors of the Typic Haploxeralf more differentiated horizons were done using different types of regressions. The results showed that soil water data obtained by the TDR equipment, corrected by the specific laboratory calibration, best fitted to “in situ” gravimetric soil water measures. In this way TDR was used for comparing to the daily exponential SWB during the four years of this second experimentation stage. Various estimations for obtaining TAW were tested; based on laboratory data – and/or on the data obtained of the soil water content field sensors. Results confirmed again, the convenience of using the daily exponential SWB, though in this case, with the TAW obtained from the field sensors graphics. Soil water estimated by exponential SWB on daily basis was compared to weekly and monthly periods, in order to know their reliability. The results obtained for a monthly period gave less AW than the ones obtained in a weekly or daily period. Finally it has been proved that the results obtained from the exponential SWB in a daily bases can be used as a useful tool in order to give complementary information to the SPI (Precipitation Standardized Index) and to help in agricultural drought studies.

Optical detection of mealiness in apples using laser TDRS

Mealiness is a textural attribute related to an internal fruit disorder that involves quality loss. It is characterised by the combination of abnormal softness of the fruit and absence of free juiciness in the mouth when eaten by the consumer. Recent research concluded with the development of precise instrumental procedure to measure a scale of mealiness based on the combination of several rheological properties and empirical magnitudes. In this line, time-domain laser reflectance spectroscopy (TDRS) is a medical technology, new in agrofood research, which is capable of obtaining physical and chemical information independently and simultaneously, and this can be of interest to characterise mealiness. Using VIS & NIR lasers as light sources, TDRS was applied in this work to Golden Delicious and Cox apples (n=90), conforming several batches of untreated samples and storage-treated (20°C & 95%RH) to promote the development of mealiness. The collected database was clustered into different groups according to their instrumental test values (Barreiro et al, 1998). The optical coefficients were used as explanatory variables when building discriminant analysis functions for mealiness, achieving a classification score above 80% of correctly identified mealy versus fresh apples.

Optical detection of mealiness in apples using laser TDRS.

Mealiness is a textural attribute related to an internal fruit disorder that involves quality loss. It is characterised by the combination of abnormal softness of the fruit and absence of free juiciness in the mouth when eaten by the consumer. Recent research concluded with the development of precise instrumental procedure to measure a scale of mealiness based on the combination of several rheological properties and empirical magnitudes. In this line, time-domain laser reflectance spectroscopy (TDRS) is a new medical technology, used to characterise the optical properties of tissues, and to locate affected areas like tumours. Among its advantages compared to more traditional spectroscopic techniques, there is the feasibility to asses simultaneously and independently two optical parameters: the absorption of the light inside the irradiated body, and the scattering of the photons across the tissues, at each wavelength, generating two coefficients (µa, absorption coeff.; and µ's, transport scattering coeff.). If it is assumed that they are related respectively to chemical components and to physical properties of the sample, TDRS can be applied to the quantification of chemicals and the measurement of the rheological properties (i.e. mealiness estimation) at the same time. Using VIS & NIR lasers as light sources, TDRS was applied in this work to Golden Delicious and Cox apples (n=90), conforming several batches of untreated samples and storage-treated (20°C & 95%RH) to promote the development of mealiness. The collected database was clustered into different groups according to their instrumental test values (Barreiro et al, 1998). The optical coefficients were used as explanatory variables when building discriminant analysis functions for mealiness, achieving a classification score above 80% of correctly identified mealy versus fresh apples.

Efficient design and optimization of bio-photonic sensing cells (BICELLs) for label free biosensing

In previous works we demonstrated the benefits of using micro–nano patterning materials to be used as bio-photonic sensing cells (BICELLs), referred as micro–nano photonic structures having immobilized bioreceptors on its surface with the capability of recognizing the molecular binding by optical transduction. Gestrinone/anti-gestrinone and BSA/anti-BSA pairs were proven under different optical configurations to experimentally validate the biosensing capability of these bio-sensitive photonic architectures. Moreover, Three-Dimensional Finite Difference Time Domain (FDTD) models were employed for simulating the optical response of these structures. For this article, we have developed an effective analytical simulation methodology capable of simulating complex biophotonic sensing architectures. This simulation method has been tested and compared with previous experimental results and FDTD models. Moreover, this effective simulation methodology can be used for efficiently design and optimize any structure as BICELL. In particular for this article, six different BICELL's types have been optimized. To carry out this optimization we have considered three figures of merit: optical sensitivity, Q-factor and signal amplitude. The final objective of this paper is not only validating a suitable and efficient optical simulation methodology but also demonstrating the capability of this method for analyzing the performance of a given number of BICELLs for label-free biosensing.

Estudio y desarrollo de sensores de fibra óptica para detección de vibraciones en ductos ascendentes submarinos

En esta tesis doctoral se describe el trabajo de investigación enfocado al estudio y desarrollo de sensores de fibra óptica para la detección de presión, flujo y vibraciones en ductos ascendentes submarinos utilizados en la extracción y transporte de hidrocarburos, con el objetivo de aplicarlos en los campos de explotación de aguas profundas en el Golfo de México pertenecientes a la Industria Petrolera Mexicana. El trabajo se ha enfocado al estudio y desarrollo de sensores ópticos cuasi distribuidos y distribuidos. En especial se ha profundizado en el uso y aplicación de las redes de Bragg (FBG) y de reflectómetros ópticos en el dominio del tiempo sensible a la fase (φ-OTDR). Los sensores de fibra óptica son especialmente interesantes para estas aplicaciones por sus ventajosas características como su inmunidad a interferencias electromagnéticas, capacidad de multiplexado, fiabilidad para trabajar en ambientes hostiles, altas temperaturas, altas presiones, ambientes salino-corrosivos, etc. Además, la fibra óptica no solo es un medio sensor sino que puede usarse como medio de transmisión. Se ha realizado un estudio del estado del arte y las ventajas que presentan los sensores ópticos puntuales, cuasi-distribuidos y distribuidos con respecto a los sensores convencionales. Se han estudiado y descrito los interrogadores de redes de Bragg y se ha desarrollado un método de calibración útil para los interrogadores existentes en el mercado, consiguiendo incertidumbres en la medida de la longitud de onda menores de ± 88 nm e incertidumbres relativas (la mas interesante en el campo de los sensores) menores de ±3 pm. Centrándose en la aplicación de las redes de Bragg en la industria del petróleo, se ha realizado un estudio en detalle del comportamiento que presentan las FBGs en un amplio rango de temperaturas de -40 ºC a 500 oC. Como resultado de este estudio se han evaluado las diferencias en los coeficientes de temperatura en diversos tramos de mas mismas, así como para diferentes recubrimientos protectores. En especial se ha encontrado y evaluado las diferencias de los diferentes recubrimientos en el intervalo de temperaturas entre -40 ºC y 60 ºC. En el caso del intervalo de altas temperaturas, entre 100 ºC y 500 ºC, se ha medido y comprobado el cambio uniforme del coeficiente de temperatura en 1pm/ºC por cada 100 ºC de aumento de temperatura, en redes independientemente del fabricante de las mismas. Se ha aplicado las FBG a la medición de manera no intrusiva de la presión interna en una tubería y a la medición del caudal de un fluido en una tubería, por la medida de diferencia de presión entre dos puntos de la misma. Además se ha realizado un estudio de detección de vibraciones en tuberías con fluidos. Finalmente, se ha implementado un sistema de detección distribuida de vibraciones aplicable a la detección de intrusos en las proximidades de los ductos, mediante un φ-OTDR. En este sistema se ha estudiado el efecto negativo de la inestabilidad de modulación que limita la detección de vibraciones distribuidas, su sensibilidad y su alcance. ABSTRACT This thesis describes the research work focused for the study and development of on optical fiber sensors for detecting pressure, flow and vibration in subsea pipes used in the extraction and transportation of hydrocarbons, in order to apply them in deepwater fields in the Gulf of Mexico belonging to the Mexican oil industry. The work has focused on the study and development of optical sensors distributed and quasi distributed. Especially was done on the use and application of fiber Bragg grating (FBG) and optical reflectometers time domain phase sensitive (φ-OTDR). The optical fiber sensors especially are interesting for these applications for their advantageous characteristics such as immunity to electromagnetic interference, multiplexing capability, reliability to work in harsh environments, high temperatures, high pressures, corrosive saline environments, etc. Furthermore, the optical fiber is not only a sensor means it can be used as transmission medium. We have performed a study of the state of the art and the advantages offered by optical sensors point, quasi-distributed and distributed over conventional sensors. Have studied and described interrogators Bragg grating and has developed a calibration method for interrogators useful for the existing interrogators in the market, resulting uncertainty in the measurement of the wavelength of less than ± 0.17 nm and uncertainties (the more interesting in the field of sensors) less than ± 3 pm. Focusing on the application of the Bragg gratings in the oil industry, has been studied in detail the behavior of the FBGs in a wide range of temperatures from -40 °C to 500 oC. As a result of this study we have evaluated the difference in temperature coefficients over various sections of the same, as well as different protective coatings. In particular evaluated and found the differences coatings in the range of temperatures between -40 º C and 60 º C. For the high temperature range between 20 ° C and 500 ° C, has been measured and verified the uniform change of the temperature coefficient at 1pm / ° C for each 100 ° C increase in temperature, in networks regardless of manufacturer thereof. FBG is applied to the non-intrusive measurement of internal pressure in a pipeline and measuring flow of a fluid in a pipe, by measuring the pressure difference between two points thereof. Therefore, has also made a study of detecting vibrations in pipes with fluids. Finally, we have implemented a distributed sensing system vibration applied to intrusion detection in the vicinity of the pipelines, by φ-OTDR. In this system we have studied the negative effect of modulation instability limits the distributed vibration detection, sensitivity and scope.

Detección óptica de harinosidad en manzana mediante una nueva técnica láser.

Mealiness, a textural disorder that produces quality loss, combines softness and absence of juiciness. The only one (destructive) test to measure it, combines information from a mechanical test on fruit probes to classify the samples according to instrumental mealiness. Time-domain laser reflectance spectroscopy (TDRS) is able to assess simultaneously and independently the absorption of the light inside the irradiated body (µa coefficient) and the scattering of the photons across the tissues (µS, transport scattering coeff.) measured at each wavelength. Using VIS&NIR lasers as light sources, TDRS was applied to Golden Delicious and Cox apples (n=90), conforming batches of untreated samples and storage-treated (20°C&95%RH) to induce mealiness development. The collected database was clustered into different groups according to their instrumental mealiness. Optical variables were used to build discriminant functions, achieving classification scores 75-89% of correctly identified mealy apples.

Calculation Methodology and Fabrication Procedures for Particle Accelerator Strip-Line Kickers: Application to the CTF3 Combiner Ring Extraction Kicker and TL2 Tail Clippers

A particle accelerator is any device that, using electromagnetic fields, is able to communicate energy to charged particles (typically electrons or ionized atoms), accelerating and/or energizing them up to the required level for its purpose. The applications of particle accelerators are countless, beginning in a common TV CRT, passing through medical X-ray devices, and ending in large ion colliders utilized to find the smallest details of the matter. Among the other engineering applications, the ion implantation devices to obtain better semiconductors and materials of amazing properties are included. Materials supporting irradiation for future nuclear fusion plants are also benefited from particle accelerators. There are many devices in a particle accelerator required for its correct operation. The most important are the particle sources, the guiding, focalizing and correcting magnets, the radiofrequency accelerating cavities, the fast deflection devices, the beam diagnostic mechanisms and the particle detectors. Most of the fast particle deflection devices have been built historically by using copper coils and ferrite cores which could effectuate a relatively fast magnetic deflection, but needed large voltages and currents to counteract the high coil inductance in a response in the microseconds range. Various beam stability considerations and the new range of energies and sizes of present time accelerators and their rings require new devices featuring an improved wakefield behaviour and faster response (in the nanoseconds range). This can only be achieved by an electromagnetic deflection device based on a transmission line. The electromagnetic deflection device (strip-line kicker) produces a transverse displacement on the particle beam travelling close to the speed of light, in order to extract the particles to another experiment or to inject them into a different accelerator. The deflection is carried out by the means of two short, opposite phase pulses. The diversion of the particles is exerted by the integrated Lorentz force of the electromagnetic field travelling along the kicker. This Thesis deals with a detailed calculation, manufacturing and test methodology for strip-line kicker devices. The methodology is then applied to two real cases which are fully designed, built, tested and finally installed in the CTF3 accelerator facility at CERN (Geneva). Analytical and numerical calculations, both in 2D and 3D, are detailed starting from the basic specifications in order to obtain a conceptual design. Time domain and frequency domain calculations are developed in the process using different FDM and FEM codes. The following concepts among others are analyzed: scattering parameters, resonating high order modes, the wakefields, etc. Several contributions are presented in the calculation process dealing specifically with strip-line kicker devices fed by electromagnetic pulses. Materials and components typically used for the fabrication of these devices are analyzed in the manufacturing section. Mechanical supports and connexions of electrodes are also detailed, presenting some interesting contributions on these concepts. The electromagnetic and vacuum tests are then analyzed. These tests are required to ensure that the manufactured devices fulfil the specifications. Finally, and only from the analytical point of view, the strip-line kickers are studied together with a pulsed power supply based on solid state power switches (MOSFETs). The solid state technology applied to pulsed power supplies is introduced and several circuit topologies are modelled and simulated to obtain fast and good flat-top pulses.