Discussion of "Simplified Model of Low Cycle Fatigue for RC Frames"

To model strength degradation due to low cycle fatigue, at least three different approaches can be considered. One possibility is based on the formulation of a new free energy function and damage energy release rate, as was proposed by Ju(1989). The second approach uses the notion of bounding surface introduced in cyclic plasticity by Dafalias and Popov (1975). From this concept, some models have been proposed to quantify damage in concrete or RC (Suaris et al. 1990). The model proposed by the author to include fatigue effects is based essentially in Marigo (1985) and can be included in this approach.

Modelization of low cycle fatigue damage in frames

Damage models based on the Continuum Damage Mechanics (CDM) include explicitly the coupling between damage and mechanical behavior and, therefore, are consistent with the definition of damage as a phenomenon with mechanical consequences. However, this kind of models is characterized by their complexity. Using the concept of lumped models, possible simplifications of the coupled models have been proposed in the literature to adapt them to the study of beams and frames. On the other hand, in most of these coupled models damage is associated only with the damage energy release rate which is shown to be the elastic strain energy. According to this, damage is a function of the maximum amplitude of cyclic deformation but does not depend on the number of cycles. Therefore, low cycle effects are not taking into account. From the simplified model proposed by Flórez-López, it is the purpose of this paper to present a formulation that allows to take into account the degradation produced not only by the peak values but also by the cumulative effects such as the low cycle fatigue. For it, the classical damage dissipative potential based on the concept of damage energy release rate is modified using a fatigue function in order to include cumulative effects. The fatigue function is determined through parameters such as the cumulative rotation and the total rotation and the number of cycles to failure. Those parameters can be measured or identified physically through the haracteristics of the RC. So the main advantage of the proposed model is the possibility of simulating the low cycle fatigue behavior without introducing parameters with no suitable physical meaning. The good performance of the proposed model is shown through a comparison between numerical and test results under cycling loading.

Thermal and mechanical effects of different excitation modes based on low frequency laser modulation in optical hyperthermia

The low frequency modulation of the laser source (menor que30KHz) allows the generation of a pulsed signal that intermittently excites the gold nanorods. The temperature curves obtained for different frequencies and duty cycles of modulation but with equal average power and identical laser parameters, show that the thermal behavior in continuous wave and modulation modes is the same. However, the cell death experiments suggest that the percentage of death is higher in the cases of modulation. This observation allows us to conclude that there are other effects in addition to temperature that contribute to the cellular death. The mechanical effects like sound or pressure waves are expected to be generated from thermal expansion of gold nanorods. In order to study the behavior and magnitude of these processes we have developed a measure device based on ultrasound piezoelectric receivers (25KHz) and a lock-in amplifier that is able to detect the sound waves generated in samples of gold nanorods during laser irradiation providing us a voltage result proportional to the pressure signal. The first results show that the pressure measurements are directly proportional to the concentration of gold nanorods and the laser power, therefore, our present work is focused on determine the real influence of these effects in the cell death process.

Photoacoustic effect measurement in aqueous suspensions of gold nanorods caused by low-frequency and low-power near-infrared pulsing laser irradiation

When aqueous suspensions of gold nanorods are irradiated with a pulsing laser (808 nm), pressure waves appear even at low frequencies (pulse repetition rate of 25 kHz). We found that the pressure wave amplitude depends on the dynamics of the phenomenon. For fixed concentration and average laser current intensity, the amplitude of the pressure waves shows a trend of increasing with the pulse slope and the pulse maximum amplitude.We postulate that the detected ultrasonic pressure waves are a sort of shock waves that would be generated at the beginning of each pulse, because the pressure wave amplitude would be the result of the positive interference of all the individual shock waves.

Dual Active Bridge based Battery Charger for Plug-in Hybrid Electric Vehicle with Charging Current Containing Low Frequency Ripple

High power density is strongly preferable for the on-board battery charger of Plug-in Hybrid Electric Vehicle (PHEV). Wide band gap devices, such as Gallium Nitride HEMTs are being explored to push to higher switching frequency and reduce passive component size. In this case, the bulk DC link capacitor of AC-DC Power Factor Correction (PFC) stage, which is usually necessary to store ripple power of two times the line frequency in a DC current charging system, becomes a major barrier on power density. If low frequency ripple is allowed in the battery, the DC link capacitance can be significantly reduced. This paper focuses on the operation of a battery charging system, which is comprised of one Full Bridge (FB) AC-DC stage and one Dual Active Bridge (DAB) DC-DC stage, with charging current containing low frequency ripple at two times line frequency, designated as sinusoidal charging. DAB operation under sinusoidal charging is investigated. Two types of control schemes are proposed and implemented in an experimental prototype. It is proved that closed loop current control is the better. Full system test including both FB AC-DC stage and DAB DC-DC stage verified the concept of sinusoidal charging, which may lead to potentially very high power density battery charger for PHEV.

Processing of ultra-wideband low-frequency signals, for application in Foliage Penetration (FOPEN) Synthetic Aperture Radar (SAR) systems

Foliage Penetration (FOPEN) radar systems were introduced in 1960, and have been constantly improved by several organizations since that time. The use of Synthetic Aperture Radar (SAR) approaches for this application has important advantages, due to the need for high resolution in two dimensions. The design of this type of systems, however, includes some complications that are not present in standard SAR systems. FOPEN SAR systems need to operate with a low central frequency (VHF or UHF bands) in order to be able to penetrate the foliage. High bandwidth is also required to obtain high resolution. Due to the low central frequency, large integration angles are required during SAR image formation, and therefore the Range Migration Algorithm (RMA) is used. This project thesis identifies the three main complications that arise due to these requirements. First, a high fractional bandwidth makes narrowband propagation models no longer valid. Second, the VHF and UHF bands are used by many communications systems. The transmitted signal spectrum needs to be notched to avoid interfering them. Third, those communications systems cause Radio Frequency Interference (RFI) on the received signal. The thesis carries out a thorough analysis of the three problems, their degrading effects and possible solutions to compensate them. The UWB model is applied to the SAR signal, and the degradation induced by it is derived. The result is tested through simulation of both a single pulse stretch processor and the complete RMA image formation. Both methods show that the degradation is negligible, and therefore the UWB propagation effect does not need compensation. A technique is derived to design a notched transmitted signal. Then, its effect on the SAR image formation is evaluated analytically. It is shown that the stretch processor introduces a processing gain that reduces the degrading effects of the notches. The remaining degrading effect after processing gain is assessed through simulation, and an experimental graph of degradation as a function of percentage of nulled frequencies is obtained. The RFI is characterized and its effect on the SAR processor is derived. Once again, a processing gain is found to be introduced by the receiver. As the RFI power can be much higher than that of the desired signal, an algorithm is proposed to remove the RFI from the received signal before RMA processing. This algorithm is a modification of the Chirp Least Squares Algorithm (CLSA) explained in [4], which adapts it to deramped signals. The algorithm is derived analytically and then its performance is evaluated through simulation, showing that it is effective in removing the RFI and reducing the degradation caused by both RFI and notching. Finally, conclusions are drawn as to the importance of each one of the problems in SAR system design.

Different approaches to grounding resistance. Calculation for thin wire structures at low frequency energization

The present paper deals with the calculation of grounding resistance of an electrode composed of thin wires, that we consider here as perfect electric conductors (PEC) e.g. with null internal resistance, when buried in a soil of uniform resistivity. The potential profile at the ground surface is also calculated when the electrode is energized with low frequency current. The classic treatment by using leakage currents, called Charge Simulated Method (CSM), is compared with that using a set of steady currents along the axis of the wires, here called the Longitudinal Currents Method (LCM), to solve the Maxwell equations. The method of moments is applied to obtain a numerical approximation of the solution by using rectangular basis functions. Both methods are applied to two types of electrodes and the results are also compared with those obtained using a thirth approach, the Average Potential Method (APM), later described in the text. From the analysis performed, we can estimate a value of the error in the determination of grounding resistance as a function of the number of segments in which the electrodes are divided.

A fatigue damage model for seismic response of RC structures

Numerous damage models have been developed in order to analyze seismic behavior. Among the different possibilities existing in the literature, it is very clear that models developed along the lines of continuum damage mechanics are more consistent with the definition of damage as a phenomenon with mechanical consequences because they include explicitly the coupling between damage and mechanical behavior. On the other hand, for seismic processes, phenomena such as low cycle fatigue may have a pronounced effect on the overall behavior of the frames and, therefore, its consideration turns out to be very important. However, most of existing models evaluate the damage only as a function of the maximum amplitude of cyclic deformation without considering the number of cycles. In this paper, a generalization of the simplified model proposed by Cipollina et al. [Cipollina A, López-Hinojosa A, Flórez-López J. Comput Struct 1995;54:1113–26] is made in order to include the low cycle fatigue. Such a model employs in its formulation irreversible thermodynamics and internal state variable theory.

Fatigue damage modelling of steel structures

In the present work a constitutive model is developed which permits the simulation of the low cycle fatigue behaviour in steel framed structures. In the elaboration of this model, the concepts of the mechanics of continuum medium are applied on lumped dissipative models. In this type of formulation an explicit coupling between the damage and the structural mechanical behaviour is employed, allowing the possibility of considering as a whole different coupled phenomena. A damage index is defined in order to model elastoplasticity coupled with damage and fatigue damage.

Local variability of serotinous cones in a Canary Island pine (Pinus canariensis) stand

The endemic Canary Island pine (Pinus canariensis) has an effective strategy to counteract fire disturbance in the short term. It has a mixed strategy that combines the presence of serotinous cones and thick barks with the ability to re-sprout from the trunk after a fire, a rare trait in pine species. High frequency of fires in the Canary Islands is related to human action, as natural fires by lightning or vulcan activity have very low frequency; hence, the how and whys of the presence of serotinous cones in the species is still a topic of debate. Previous studies showed that the frequency of serotinous cones varies from stand to stand. Here, we analyzed the presence of serotinous cones at a local scale. We selected a Canary Island pine stand in the transition zone between dry and humid forests in the south of Tenerife. Branches were pruned from 20 trees in order to evaluate the presence of serotinous vs. non-serotinous cones by direct verticile counting on the branches. The opening temperature of serotinous cones was assessed in the laboratory. Percentages of serotinous vs. non-serotinous cones varied from 0 to 93 %, showing high variability between trees. Opening temperatures were very high (above 65 ºC) as compared to other Mediterranean pine species with serotinous cones

Evidence of charge carrier number fluctuations in InN thin films?

Due to its small band-gap and its high mobility, InN is a promising material for a large number of key applications like band-gap engineering for high efficiency solar cells, light emitting diodes, and high speed devices. Unfortunately, it has been reported that this material exhibits strong surface charge accumulation which may depend on the type of surface. Current investigations are conducted in order to explain the mechanisms which govern such a behavior and to look for ways of avoiding it and/or finding applications that may use such an effect. In this framework, low frequency noise measurements have been performed at different temperatures on patterned MBE grown InN layers. The evolution of the 1/f noise level with temperature in the 77 K-300 K range is consistent with carrier number fluctuations thus indicating surface mechanisms: the surface charge accumulation is confirmed by the noise measurements.

Thermal effects in Ni/Au and Mo/Au gate metallization AlGaN/GaN HEMT's reliability

AlGaN/GaN high electron mobility transistors (HEMT) are key devices for the next generation of high-power, high-frequency and high-temperature electronics applications. Although significant progress has been recently achieved [1], stability and reliability are still some of the main issues under investigation, particularly at high temperatures [2-3]. Taking into account that the gate contact metallization is one of the weakest points in AlGaN/GaN HEMTs, the reliability of Ni, Mo, Pt and refractory metal gates is crucial [4-6]. This work has been focused on the thermal stress and reliability assessment of AlGaN/GaN HEMTs. After an unbiased storage at 350 o C for 2000 hours, devices with Ni/Au gates exhibited detrimental IDS-VDS degradation in pulsed mode. In contrast, devices with Mo/Au gates showed no degradation after similar storage conditions. Further capacitance-voltage characterization as a function of temperature and frequency revealed two distinct trap-related effects in both kinds of devices. At low frequency (< 1MHz), increased capacitance near the threshold voltage was present at high temperatures and more pronounced for the Ni/Au gate HEMT and as the frequency is lower. Such an anomalous “bump” has been previously related to H-related surface polar charges [7]. This anomalous behavior in the C-V characteristics was also observed in Mo/Au gate HEMTs after 1000 h at a calculated channel temperatures of around from 250 o C (T2) up to 320 ºC (T4), under a DC bias (VDS= 25 V, IDS= 420 mA/mm) (DC-life test). The devices showed a higher “bump” as the channel temperature is higher (Fig. 1). At 1 MHz, the higher C-V curve slope of the Ni/Au gated HEMTs indicated higher trap density than Mo/Au metallization (Fig. 2). These results highlight that temperature is an acceleration factor in the device degradation, in good agreement with [3]. Interface state density analysis is being performed in order to estimate the trap density and activation energy.

Wave-like Disturbances on the Downstream Wall of an Open Cavity

This contribution presents results of an incompressible two-dimensional flow over an open cavity of fixed aspect ratio (length/depth) L/D = 2 and the coupling between the three dimensional low frequency oscillation mode confined in the cavity and the wave-like disturbances evolving on the downstream wall of the cavity in the form of Tollmien-Schlichting waves. BiGlobal instability analysis is conducted to search the global disturbances superimposed upon a two-dimensional steady basic flow. The base solution is computed by the integration of the laminar Navier-Stokes equations in primitive variable formulation, while the eigenvalue problem (EVP) derived from the discretization of the linearized equations of motion in the BiGlobal framework is solved using an iterative procedure. The formulation of the BiGlobal EVP for the unbounded flow in the open cavity problem introduces additional difficulties regarding the flow-through boundaries. Local analysis has been utilized for the determination of the proper boundary conditions in the upper limit of the downstream region

Bases moleculares de la resistencia a insecticidas en la mosca mediterránea de la fruta Ceratitis Capitata (Wiedemann)

La mosca mediterránea de la fruta Ceratitis capitata (Wiedemann, 1824) está considerada una de las plagas clave para la fruticultura. El malatión es un insecticida organofosforado que fue empleado mayoritariamente en España para el control de C. capitata hasta 2009, año en el que dejó de utilizarse por no estar incluido en el anexo I de la Directiva Europea 91/414/ECC. El incremento del uso del malatión, debido a las graves pérdidas económicas causadas por C. capitata, provocó la aparición de poblaciones de campo resistentes. El estudio de una población resistente a malatión, recogida en Castelló en 2004, permitió la identificación de dos mecanismos de resistencia: una mutación puntual (G328A) en la acetilcolinesterasa (AChE) y un mecanismo de resistencia metabólica, probablemente mediado por carboxilesterasas. Teniendo en cuenta estos antecedentes, nos propusimos estudiar los mecanismos implicados en la resistencia a malatión en C. capitata. Además, durante el desarrollo de esta Tesis, el malatión fue sustituido por otros insecticidas como el espinosad y la lambda-cialotrina para el control de la plaga. En este nuevo contexto, es extremadamente importante analizar la susceptibilidad de poblaciones de campo frente a espinosad y estudiar la posible existencia de resistencia cruzada a estos insecticidas, así como sentar las bases para el estudio de futuros mecanismos de resistencia. En primer lugar, analizamos mediante bioensayos con dosis discriminante la susceptibilidad a malatión y espinosad en doce poblaciones de C. capitata de Andalucía, Aragón, Cataluña, Comunidad Valenciana e Islas Baleares; y nuestros resultados sugirieron la presencia de individuos resistentes a malatión en la mayoría de las poblaciones analizadas. En el caso del espinosad, observamos que la susceptibilidad a este insecticida de origen biológico fue elevada en la mayoría de las poblaciones, sin embargo, la población recogida en Xàbia (Alicante) mostró un nivel de susceptibilidad unas dos veces menor al resto de poblaciones. Mediante la selección en laboratorio, obtuvimos dos líneas resistentes a malatión, W-4Km y W-10Km, con unos niveles de resistencia con respeto a la línea susceptible C de 178 y 400 veces, respectivamente. Además, se seleccionó por primera vez en C. capitata una línea altamente resistente a espinosad (Xàbia-W-100s), que actualmente es unas 500 veces más resistente que la línea de laboratorio C. Con el objetivo de escoger la estrategia más adecuada para el manejo de la plaga, estudiamos la susceptibilidad a diferentes tipos de insecticidas en la línea resistente a malatión W- 4Km. En esta línea detectamos resistencia cruzada moderada a los organofosforados fentión, diazinón, fosmet, triclorfón y metil-clorpirifos (de 7 a 16 veces) y frente al carbamato carbaril, al piretroide lambda-cialotrina y al quimioesterilizante lufenurón (de 4 a 6 veces). Por otra parte, la resistencia cruzada frente a espinosad fue baja (1,5 veces). Es importante destacar que los niveles de resistencia estimados frente a todos los insecticidas fueron de uno o dos órdenes de magnitud inferiores al observado en la línea W-4Km frente a malatión (178 veces), hecho que podría deberse, al menos, a dos posibles hipótesis: que la mutación AChE G328A confiera mayor insensibilidad al malaoxón (forma activa del malatión) que a otros insecticidas que tienen como diana la AChE y/o, en segundo lugar, que el mecanismo de resistencia mediado por carboxilesterasas hidrolice el malatión de manera más eficiente que los otros insecticidas analizados. En el estudio de nuevos mecanismos de resistencia en C. capitata, por un lado, analizamos la diversidad de enzimas citocromo P450, asociadas con resistencia metabólica en otras especies, y por otro lado, desarrollamos un sistema para la detección de nuevas mutaciones puntuales que pudiesen aparecer en los genes que codifican la AChE (Ccace2) y la aliesterasa (Ccae7). Mediante el empleo de cebadores degenerados obtuvimos 37 genes CYP, que codifican enzimas P450, pertenecientes a cinco familias. Posteriormente, en un estudio de inducción con fenobarbital, observamos que la expresión de cuatro de los seis genes analizados era susceptible de ser inducida. Por otro lado, se puso a punto un sistema que permite amplificar y secuenciar, a partir de DNA genómico, los exones de los genes Ccace2 y Ccae7 en los que se han encontrado mutaciones relacionadas con resistencia a insecticidas en otras especies. Los resultados obtenidos facilitarán el estudio de nuevos mecanismos de resistencia mediados por estas enzimas en C. capitata. Se diseñó un método PCR-RFLP para identificar los individuos portadores de la mutación AChE G328A (alelo de resistencia Ccace2R) sin la necesidad de realizar bioensayos y que, además, permite detectar resistencia cuando ésta se encuentra a baja frecuencia. Según el análisis realizado, el alelo Ccace2R se observó en 25 de las 27 localidades españolas muestreadas en el territorio español, incluyendo las Islas Baleares y Canarias. Sin embargo, este alelo no se detectó en poblaciones procedentes de once países y de cinco continentes. El análisis de la presencia del alelo Ccace2R en las líneas resistentes a malatión durante el proceso de selección en el laboratorio mostró una rápida disminución de los homocigotos, tanto para el alelo susceptible como para el alelo de resistencia, en favor de los individuos heterocigotos. Así, después de 52 generaciones de selección, se observó que la totalidad de los individuos analizados de la línea W-10Km presentaban un genotipo heterocigoto para la mutación AChE G328A. Este desequilibrio contradice la segregación mendeliana esperada para un gen con dos alelos pero podría ser explicado por la existencia de una duplicación del gen Ccace2. La demostración de la presencia de esta duplicación se realizó mediante: i) el cruzamiento de individuos heterocigotos de la línea W-10Km con homocigotos susceptibles de la línea C, que dio lugar a una descendencia en la que el 100% de los individuos eran heterocigotos; ii) la evaluación del número de copias del gen Ccace2 por PCR cuantitativa en tiempo real (qPCR), que resultó dos veces mayor en individuos de la línea W-10Km en comparación con los de la línea C; iii) el análisis del nivel de expresión de Ccace2, que fue el doble en la línea W-10Km con respecto a la línea C, y iv) el estudio de la actividad AChE, que resultó mayor en los individuos de la línea W-10Km. Según los resultados obtenidos, una duplicación del gen Ccace2 provoca la coexistencia en un mismo cromosoma del alelo silvestre y del alelo mutado y, además, las dos copias del gen Ccace2, al estar ligadas, producen una heterocigosis permanente (Ccace2RS). De esta manera se explica que el hecho de que 100% de los individuos de la línea W-10Km mostrasen un perfil de restricción correspondiente a un individuo heterocigoto ya que, en realidad, eran homocigotos estructurales para la duplicación (genotipo CCace2RS/RS). Se ha detectado un coste biológico asociado a la duplicación que consiste en un incremento en la mortalidad acumulada de los adultos a partir del séptimo día después de la emergencia. La descripción de la duplicación Ccace2RS supone la identificación de un nuevo mecanismo de resistencia a malatión en C. capitata. Finalmente, mediante el diseño de un método de doble PCR-RFLP se determinó la presencia de la duplicación Ccace2RS en la mayoría de las poblaciones españolas. La proporción de individuos portadores de la duplicación osciló entre el 5% y el 35%, observándose los mayores valores de frecuencia en las poblaciones de C. capitata recogidas en la cuenca mediterránea. Podemos por lo tanto concluir que la resistencia a malatión asociada a la mutación AChE G328A y a la duplicación Ccace2RS está ampliamente establecida en las poblaciones españolas de C. capitata. Nuestros resultados desaconsejan la utilización del malatión (si fuera de nuevo autorizado) o de otros organofosforados para el control de esta plaga. Además, una de las líneas resistentes a malatión mostró resistencia cruzada frente a insecticidas con diferentes modos de acción y que se utilizan actualmente para el control de C. capitata, tales como lambda-cialotrina y lufenurón. La alta susceptibilidad a espinosad observada en las poblaciones españolas, así como la reducida resistencia cruzada estimada para este insecticida, sugieren que su utilización es adecuada para el control de la plaga. Sin embargo, la utilización de un sólo insecticida puede entrañar riesgos por favorecer la selección de resistencia, de hecho, mediante selección en laboratorio se obtuvo una población altamente resistente a espinosad. Por tanto, es recomendable implementar programas de control integrado y de manejo de la resistencia en C. capitata utilizando distintos sistemas de control e insecticidas con diferentes mecanismos de acción que permitan su sostenibilidad en el tiempo. Los sistemas de detección de alelos de resistencia desarrollados en este trabajo permitirán la detección precoz de resistencia en campo, facilitando la decisión sobre el sistema de control más adecuado. Además, los conocimientos generados podrán contribuir al desarrollo de nuevos sistemas de detección para otros mecanismos de resistencia. Abstract. The Mediterranean fruit fly, Ceratitis capitata (Wiedemann, 1824), is considered one of the most harmful pests in fruit crops. Until 2009, when malathion use was banned due to its not inclusion in the Annex I of Directive 91/414/EEC, the application of this organophosphate (OP) insecticide in Spain increased gradually due to the large economic losses caused by C. capitata. The increase in the frequency of treatments resulted in the development of resistant field populations. The study of a malathion-resistant population, collected in 2004 in Castelló (Comunidad Valenciana), allowed the identification of two resistance mechanisms: a single point mutation (G328A) in the target acetylcholinesterase (AChE), as well as a metabolic resistance mechanism, most likely carboxylesterase-mediated. Taking all the preceding into account, we studied the malathion resistance mechanisms in C. capitata. During the development of this PhD Thesis malathion use was banned by the European Union, being replaced by other insecticides, such as spinosad and lambda-cyhalotrin. Within this new working frame, the need to analyse the possible existence of cross-resistance to these insecticides and the susceptibility to spinosad in field populations was raised. This would define the baseline for future studies on resistance mechanisms. Firstly, through discriminant dose bioassays, we analysed malathion and spinosad susceptibility in twelve C. capitata populations from Andalucia, Aragon, Cataluña, C. Valenciana and the Baleares Islands. Our results suggest the presence of malathion-resistant individuals in most of the populations analysed. Regarding spinosad, we noticed a high susceptibility to this biologically derived insecticide in most of the populations, but in the one collected in Xabia (Alicante), which had a susceptibility level two times lower than the rest of populations. Through laboratory selection, we obtained two malathion-resistant strains, W-4Km and W-10Km, with resistance levels 178- and 400-fold, respectively, compared to the control susceptible C strain. Besides, a strain highly-resistant to spinosad (Xabia-W-100s), 500-times more resistant than control C strain, was selected. In order to decide the most appropriate management strategy for the pest, we studied the susceptibility to different insecticides in the malathion-resistant W-4Km strain. We detected a moderated cross-resistance to the OPs fenthion, diazinon, phosmet, trichlorphon and methylchlorpyrifos (7- to 16-fold), and to the carbamate carbaryl, the pyretroid lambda-cyhalotrin and the chemosterilizer lufenuron (4- to 6-fold). On the other hand, cross-resistance to spinosad was low (1.5-fold). It is important to note that resistance levels to all insecticides were one or two orders of magnitude less than that observed against malathion in W-4Km strain (178-fold), a fact that might be due to, at least, two possible causes: mutation AChE G328A may provide a higher insensitivity to malaoxon (the active form of malathion) than to other insecticides having AChE as target, and/or, secondly, the carboxylesterase-mediated resistance mechanism hydrolyzes malathion more efficiently than all other analysed insecticides. To investigate new resistance mechanisms in C. capitata we analysed the diversity of the cytochrome P450 enzymes, which have been associated to metabolic resistance in insects, and we developed a new method to detect single point mutations in acetylcholinesterase (Ccace2) and aliesterase (Ccae7) genes that could appear. Using degenerate primers we obtained 37 CYP genes, coding P450 enzymes, included in five families. Afterwards, in a phenobarbital-induction study, we observed that the expression of 4 out of the 6 analysed genes could be induced. On the other hand, a system was set up to amplify and to sequence from genomic DNA the exons of genes Ccace2 and Ccae7 where mutations related to insecticide resistance have been found in other species. The results obtained could facilitate the study of new resistance mechanisms in C. capitata mediated by these enzymes. A PCR-RFLP method was designed to detect the presence of the mutation AChE G328A (resistance allele Ccace2R), with no need to perform bioassays and allowing detecting resistance at low frequency. According to the analysis, the resistance allele was found in 25 out of 27 sampled locations in Spain, including the Balearic and the Canary Islands. However, this allele was not detected in other populations collected in 11 countries from 5 continents. The follow-up of the presence of the allele Ccace2R in the malathion-resistant strains during the selection process in the laboratory showed a quick decrease in homozygous individuals, for both the susceptible and the resistant alleles, favouring heterozygous. Thus, after 52 generations of selection, all the individuals analysed from W-10Km strain showed a heterozygous genotype for mutation AChE G328A, contradicting mendelian segregation as expected for a gene with two alleles. Afterwards, we were able to demonstrate that this was caused by the presence of a duplication of the gene coding acetylcholinesterase by: i) crossing heterozygous individuals from W-10Km strain with susceptible homozygous from C strain, originating a F1 population in which 100% of individuals were heterozygous; ii) evaluating the number of copies of gen Ccace2 by quantitative PCR in real time (qPCR), that happened to be twice higher in individuals from W-10Km VII strain when compared with C strain; iii) analysing the level of expression of Ccace2, twice in W- 10Km strain when compared to C strain; iv) studying the acetylcholinesterase activity, that was higher in individuals from W-10Km strain. According to these results, duplication of gen Ccace2 originates the coexistence of the susceptible and the resistant allele in the same chromosome. The two linked copies of the gene Ccace2 provoke the existence of permanent heterozygosis (Ccace2RS). This explains why the 100% of individuals from W-10Km strain showed an heterozygous restriction pattern since, in fact, they were structural homozygotes for the duplication (genotype Ccace2RS/RS). A biological cost has been detected associated to this duplication, consisting in a rise in accumulated adult mortality from the seventh day after emergence. The Ccace2RS duplication described in this study represents a new resistance mechanism to malathion in C. capitata. Finally, by the design of a double PCR-RFLP method, the presence of Ccace2RS duplication was confirmed in most of the Spanish populations. We observed that the proportion of individuals carrying the duplication oscillated between 5 and 35%, the frequency being higher in those C. capitata populations collected in the area of the Mediterranean basin. Therefore, we can conclude that malathion resistance associated to mutation AChE G328A and to Ccace2RS duplication are widely distributed in Spanish populations of C. capitata. Our results advice against the use of malathion (if it came to be newly authorized for use) or other OPs for the control of this pest. Besides, one of the malathion-resistant strains showed cross-resistance against insecticides with diverse action modes that are currently used for pest control, such as lambdacyhalotrin and lufenuron. High susceptibility to spinosad in the Spanish populations, as well as the reduced cross-resistance estimated for this insecticide suggests its adequacy for Medfly control. However, the use of a single insecticide is a risky strategy since it favours the selection of resistance. In fact, a population highly resistant to spinosad was obtained through laboratory selection. Therefore, it is advisable to implement integrated pest management (IPM) and resistance management programs for C. capitata control. Using insecticides with different modes of action and diverse control systems would contribute to the sustainability of the pest control. The resistance allele detection systems developed through this work will allow the early detection of resistance in the field, making possible the selection of the most appropriate method for pest control. Besides, the generated knowledge may also contribute to the development of new detection systems for other resistance mechanisms.

Hysteresis phenomena in transverse galloping of triangular cross-section bodies

Transverse galloping is a type of aeroelastic instability characterised by large amplitude, low frequency oscillation of a structure in the direction normal to the mean wind direction. It normally appears in bodies with small stiffness and structural damping, provided the incident flow velocity is high enough. In the simplest approach transverse galloping can be considered as a one-degree-of-freedom oscillator subjected to aerodynamic forces, which in turn can be described by using a quasi-steady description. In this frame it has been demonstrated that hysteresis phenomena in transverse galloping is related to the existence of inflection points in the curve giving the dependence with the angle of attack of the aerodynamic coefficient normal to the incident flow. Aiming at experimentally checking such a relationship between these inflection points and hysteresis, wind tunnel experiments have been conducted. Experiments have been restricted to isosceles triangular cross-section bodies, whose galloping behaviour is well documented. Experimental results show that, according to theoretical predictions, hysteresis takes place at the angles of attack where there are inflection points in the lift coefficient curve, provided that the body is prone to gallop at these angles of attack.