Laser Shock Processing influence on local properties and overall tensile behavior of friction stir welded joints

Based on laser beam intensities above 109 W/cm2 with pulse energy of several Joules and duration of nanoseconds, Laser Shock Processing (LSP) is capable of inducing a surface compressive residual stress field. The paper presents experimental results showing the ability of LSP to improve the mechanical strength and cracking resistance of AA2024-T351 friction stir welded (FSW) joints. After introducing the FSW and LSP procedures, the results of microstructural analysis and micro-hardness are discussed. Video Image Correlation was used to measure the displacement and strain fields produced during tensile testing of flat specimens; the local and overall tensile behavior of native FSW joints vs. LSP treated were analyzed. Further, results of slow strain rate tensile testing of the FSW joints, native and LSP treated, performed in 3.5% NaCl solution are presented. The ability of LSP to improve the structural behavior of the FSW joints is underscored.

Shake-table tests of a reinforced concrete frame designed following modern codes: seismic performance and damage evaluation

This paper presents shake-table tests conducted on a two-fifths-scale reinforced concrete frame representing a conventional construction design under current building code provisions in the Mediterranean area. The structure was subjected to a sequence of dynamic tests including free vibrations and four seismic simulations in which a historical ground motion record was scaled to levels of increasing intensity until collapse. Each seismic simulation was associated with a different level of seismic hazard, representing very frequent, frequent, rare and very rare earthquakes. The structure remained basically undamaged and within the inter-story drift limits of the "immediate occupancy" performance level for the very frequent and frequent earthquakes. For the rare earthquake, the specimen sustained significant damage with chord rotations of up to 28% of its ultimate capacity and approached the upper bound limit of inter-story drift associated with "life safety". The specimen collapsed at the beginning of the "very rare" seismic simulation. Besides summarizing the experimental program, this paper evaluates the damage quantitatively at the global and local levels in terms of chord rotation and other damage indexes, together with the energy dissipation demands for each level of seismic hazard. Further, the ratios of column-to-beam moment capacity recommended by Eurocode 8 and ACI-318 to guarantee the formation of a strong column-weak beam mechanism are examined.

Nuevo concepto de elementos estructurales horizontales de vidrio : placa autoportante y pretensada en forma de pi

En los últimos años, podemos darnos cuenta de la importancia que tienen las nuevas aplicaciones de vidrio especialmente en edificios turísticos donde el vértigo juega un papel importante en la visita. Sin embargo los sistemas constructivos no tienen un especial interés porque el vidrio laminado está siempre soportado por otro elemento de acero o incluso vidrio en forma de retícula. En la presente tesis voy a desarrollar una nueva solución de elemento autoportante de vidrio de gran tamaño haciendo seguro el uso del elemento para andar en el aire. El sueño de muchos arquitectos ha sido diseñar un edificio completamente transparente y a mí me gustaría contribuir a este sueño empezando a estudiar un forjado de vidrio como elemento estructural horizontal y para ello debemos cumplir requerimientos de seguridad. Uno de los objetivos es lograr un elemento lo más transparente y esbelto posible para el uso de pasarelas en vestíbulos de edificios. Las referencias construidas son bien conocidas, pero por otro lado Universidades europeas estudian continua estudiando el comportamiento del vidrio con diferentes láminas, adhesivos, apilados, insertos, sistemas de laminado, pretensado, pandeo lateral, seguridad post-rotura y muchos más aspectos necesarios. La metodología llevada a cabo en esta tesis ha sido primeramente diseñar un elemento industrial prefabricado horizontal de vidrio teniendo en cuenta todos los conceptos aprendidos en el estado del arte y la investigación para poder predimensionar el elemento. El siguiente paso será verificar el modelo por medio de cálculo analítico, simulación de elementos finitos y ensayos físicos. Para realizar los ensayos hay un paso intermedio teniendo que cambiar la hipótesis de carga uniforme a carga puntal para realizar el ensayo de flexión a 4 puntos normalizado y además cambiar a escala 1:2 para adaptarse al espacio de ensayo y ser viable económicamente. Finalmente compararé los resultados de tensión y deformación obtenidos por los tres métodos para extraer conclusiones. Sin embargo el problema de la seguridad no ha concluido, tendré que demostrar que el sistema es seguro después de que se produzca la rotura y para ello sólo dispongo de los ensayos como medio de demostración. El diseño es el resultado de la evolución de una viga tipo “I”; cuando es pretensada para obtener más resistencia, aparece el problema de pandeo lateral y éste es solucionado con una viga con sección en “T” cuya unión es resuelta con un cajeado longitudinal en la parte inferior del elemento horizontal. Las alas de éste crecen para recoger las cargas superficiales creando a su vez un punto débil en la unión que a su vez se soluciona duplicando la sección “TT” y haciendo trabajar dicho tablero de forma tan óptima como una viga continua. Dicha sección en vidrio como un único elemento pretensado es algo inédito. Además he diseñado unas escuadras metálicas en los extremos de los nervios como apoyo y placa de pretensión, así como una hendidura curva en el centro de los nervios para alojar los tirantes de acero de modo que al pretensar el tirante la placa corrija al menos la deformación por peso propio. Realizados los cambios geométricos de escala y las simplificaciones en el laminado y el adhesivo se programan la extracción de resultados desde 3 estadios diferentes: Sin pretensión y con pretensión de 750 Kg y de 1000Kg en cada nervio. Por cada estadio y por cada uno de los métodos, cálculo, simulación y ensayos, se extraen los datos de deformación y tensión en el punto medio de un nervio con el objetivo de hacer una comparación de resultados para obtener unas conclusiones, siempre en el campo de la elasticidad. Posteriormente incrementaré la carga hasta el momento de la rotura de la placa y después hasta el colapso teniendo en cuenta el tiempo y demostrando una rotura segura. El vidrio no tendrá un comportamiento plástico pero habrá sido controlado su comportamiento frágil manteniendo una carga y una deformación aceptable. ABSTRACT Over the past few years we have realized the importance of the new technologies regarding the application of glass in new buildings, especially those touristic places were the views and the heights are the reason of the visit. However, the construction systems of these glass platforms are not usually as interesting, because the laminated glass is always held by another steel substructure or even a grid-formed glass element. Throughout this thesis I am going to develop a new solution of a self-bearing element with big dimensions made out of glass, ensuring a safe solution to use as an element to walk on the air. The dream of many architects has been to create a building completely transparent, and I would like to contribute to this idea by making a glass slab as a horizontal structural element, for which we have to meet the security requirements. One of the goals is to achieve an element as transparent and slim as possible for the use in walkways of building lobbies. The glass buildings references are well known, but on the other hand the European Universities study the behaviour of the glass with different interlayers, adhesives, laminating systems, stacking, prestressed, buckling, safety, breakage and post-breakage capacity; and many other necessary aspects. The methodology followed in this thesis has been to first create a horizontal industrial prefabricated horizontal element of glass, taking into account all the concepts learned in the state of art and the investigation to be able to predimension this element. The next step will be to verify this model with an analytic calculus, a finite element modelling simulation and physical tests. To fulfil these tests there is an intermediate step, having to change the load hypothesis from a punctual one to make the test with a four points normalized deflexion, and also the scale of the sample was changed to 1:2 to adapt to the space of the test and make it economically possible. Finally, the results of tension and deformation obtained from the three methods have been compared to make the conclusions. However, the problem with safety has not concluded yet, for I will have to demonstrate that this system is safe even after its breakage, for which I can only use physical tests as a way of demonstration. The design is the result of the evolution of a typical “I” beam, which when it is prestressed to achieve more resistance, the effect of buckling overcomes, and this is solved with a “T” shaped beam, where the union is solved with a longitudinal groove on the inferior part of the horizontal element. The boards of this beam grow to cover the superficial loads, creating at the same time a weak point, which is solved by duplicating the section “TT” and therefore making this board work as optimal as a continuous beam. This glass section as a single prestressed element is unique. After the final design of the “π” glass plate was obtained and the composition of the laminated glass and interlayers has been predimensioned, the last connection elements must be contemplated. I have also designed a square steel shoe at the end of the beams, which will be the base and the prestressed board, as well as a curved slot in the centre of the nerves to accommodate the steel braces so that when this brace prestresses the board, at least the deformation due to its self-weight will be amended. Once I made the geometric changes of the scale and the simplifications on the laminating and the adhesive, the extraction on results overcomes from three different stages: without any pretension, with a pretension of 750 kg and with a pretension of 1000 kg on each rib. For each stage and for each one of the methods, calculus, simulation and tests, the deformation datum were extracted to obtain the conclusions, always in the field of the elasticity. Afterwards, I will increase the load until the moment of breakage of this board, and then until the collapse of the element, taking into account the time spent and demonstrating a safe breakage. The glass will not have a plastic behaviour, but its brittle behaviour has been controlled, keeping an acceptable load and deflection.

PV self-consumption optimization with storage and Active DSM for the residential sector

With the rising prices of the retail electricity and the decreasing cost of the PV technology, grid parity with commercial electricity will soon become a reality in Europe. This fact, together with less attractive PV feed-in-tariffs in the near future and incentives to promote self-consumption suggest, that new operation modes for the PV Distributed Generation should be explored; differently from the traditional approach which is only based on maximizing the exported electricity to the grid. The smart metering is experiencing a growth in Europe and the United States but the possibilities of its use are still uncertain, in our system we propose their use to manage the storage and to allow the user to know their electrical power and energy balances. The ADSM has many benefits studied previously but also it has important challenges, in this paper we can observe and ADSM implementation example where we propose a solution to these challenges. In this paper we study the effects of the Active Demand-Side Management (ADSM) and storage systems in the amount of consumed local electrical energy. It has been developed on a prototype of a self-sufficient solar house called “MagicBox” equipped with grid connection, PV generation, lead–acid batteries, controllable appliances and smart metering. We carried out simulations for long-time experiments (yearly studies) and real measures for short and mid-time experiments (daily and weekly studies). Results show the relationship between the electricity flows and the storage capacity, which is not linear and becomes an important design criterion.

Integration of socioeconomic and genetic aspects involved in the conservation of animal genetic resources = Integración de aspectos socioeconómicos y genéticos involucrados en la conservación de recursos genéticos animales

El sector ganadero está siendo gradualmente dominado por sistemas intensivos y especializados en los que los factores de producción están controlados y en los que los caracteres productivos son los criterios principales para la selección de especies y razas. Entretanto, muchos de los bienes y servicios que tradicionalmente suministraba el ganado, tales como los fertilizantes, la tracción animal o materias primas para la elaboración vestimenta y calzado están siendo reemplazados por productos industriales. Como consecuencia de ambos cambios, las razas seleccionadas intensivamente, las cuales están estrechamente ligadas a sistemas agrícolas de alta producción y altos insumos, han desplazado a muchas razas autóctonas, en las que la selección prácticamente ha cesado o es muy poco intensa. Actualmente existe una mayor conciencia social sobre la situación de las razas autóctonas y muchas funciones del ganado que previamente habían sido ignoradas están siendo reconocidas. Desde hace algunas décadas, se ha aceptado internacionalmente que las razas de ganado cumplen funciones económicas, socio-culturales, medioambientales y de seguridad alimentaria. Por ello, diferentes organismos internacionales han reconocido que la disminución de los recursos genéticos de animales domésticos (RGADs) es un problema grave y han recomendado su conservación. Aun así, la conservación de RGADs es un tema controvertido por la dificultad de valorar las funciones del ganado. Esta valoración es compleja debido que los RGADs tiene una doble naturaleza privada - pública. Como algunos economistas han subrayado, el ganado es un bien privado, sin embargo debido a algunas de sus funciones, también es un bien público. De esta forma, el aumento del conocimiento sobre valor de cada una de sus funciones facilitaría la toma de decisiones en relación a su conservación y desarrollo. Sin embargo, esta valoración es controvertida puesto que la importancia relativa de las funciones del ganado varía en función del momento, del lugar, de las especies y de las razas. El sector ganadero, debido a sus múltiples funciones, está influenciado por factores técnicos, medioambientales, sociales, culturales y políticos que están interrelacionados y que engloban a una enorme variedad de actores y procesos. Al igual que las funciones del ganado, los factores que afectan a su conservación y desarrollo están fuertemente condicionados por localización geográfica. Asimismo, estos factores pueden ser muy heterogéneos incluso dentro de una misma raza. Por otro lado, es razonable pensar que el ganadero es el actor principal de la conservación de razas locales. Actualmente, las razas locales están siendo Integration of socioeconomic and genetic aspects involved in the conservation of animal genetic resources 5 explotadas por ganaderos muy diversos bajo sistemas de producción también muy diferentes. Por todo ello, es de vital importancia comprender y evaluar el impacto que tienen las motivaciones, y el proceso de toma de decisiones de los ganaderos en la estructura genética de las razas. En esta tesis doctoral exploramos diferentes aspectos sociales, económicos y genéticos involucrados en la conservación de razas locales de ganado vacuno en Europa, como ejemplo de RGADs, esperando contribuir al entendimiento científico de este complejo tema. Nuestro objetivo es conseguir una visión global de los procesos subyacentes en la conservación y desarrollo de estas razas. Pretendemos ilustrar como se pueden utilizar métodos cuantitativos en el diseño y establecimiento de estrategias de conservación y desarrollo de RGADs objetivas y adecuadas. En primer lugar, exploramos el valor económico total (VET) del ganado analizando sus componentes públicos fuera de mercado usando como caso de estudio la raza vacuna Alistana-Sanabresa (AS). El VET de cualquier bien está formado por componentes de uso y de no-uso. Estos últimos incluyen el valor de opción, el valor de herencia y el valor de existencia. En el caso del ganado local, el valor de uso directo proviene de sus productos. Los valores de uso indirecto están relacionados con el papel que cumple las razas en el mantenimiento de los paisajes y cultura rural. El valor de opción se refiere a su futuro uso potencial y el valor de herencia al uso potencial de las generaciones venideras. Finalmente, el valor de existencia está relacionado con el bienestar que produce a la gente saber que existe un recurso específico. Nuestro objetivo fue determinar la importancia relativa que tienen los componentes fuera de mercado sobre el VET de la raza AS. Para ello evaluamos la voluntad de la gente a pagar por la conservación de la AS mediante experimentos de elección (EEs) a través de encuestas. Estos experimentos permiten valorar individualmente los distintos componentes del VET de cualquier bien. Los resultados los analizamos mediante de uso de modelos aleatorios logit. Encontramos que las funciones públicas de la raza AS tienen un valor significativo. Sus valores más importantes son el valor de uso indirecto como elemento cultural Zamorano y el valor de existencia (ambos representaron el 80% de VET). Además observamos que el valor que gente da a las funciones públicas de la razas de ganado dependen de sus características socioeconómicas. Los factores que condicionaron la voluntad a pagar para la conservación de la raza AS fueron el lugar de residencia (ciudad o pueblo), el haber visto animales de la raza o haber consumido sus productos y la actitud de los encuestados ante los conflictos entre el desarrollo económico y el medioambiente. Por otro lado, encontramos que no todo el mundo tiene una visión completa e integrada de todas las funciones públicas de la raza AS. Por este motivo, los programas o actividades de concienciación sobre su estado deberían hacer hincapié en este aspecto. La existencia de valores públicos de la raza AS implica que los ganaderos deberían recibir compensaciones económicas como pago por las funciones públicas que cumple su raza local. Las compensaciones asegurarían un tamaño de población que permitiría que la raza AS siga realizando estas funciones. Un mecanismo para ello podría ser el desarrollo del turismo rural relacionado con la raza. Esto aumentaría el valor de uso privado mientras que supondría un elemento añadido a las estrategias de conservación y desarrollo. No obstante, los ganaderos deben analizar cómo aprovechar los nichos de mercado existentes, así como mejorar la calidad de los productos de la raza prestando especial atención al etiquetado de los mismos. Una vez evaluada la importancia de las funciones públicas de las razas locales de ganado, analizamos la diversidad de factores técnicos, económicos y sociales de la producción de razas locales de ganado vacuno existente en Europa. Con este fin analizamos el caso de quince razas locales de ocho países en el contexto de un proyecto de colaboración internacional. Investigamos las diferencias entre los países para determinar los factores comunes clave que afectan a la viabilidad de las razas locales. Para ello entrevistamos mediante cuestionarios a un total de 355 ganaderos en las quince razas. Como indicador de viabilidad usamos los planes de los ganaderos de variación del tamaño de las ganaderías. Los cuestionarios incluían diferentes aspectos económicos, técnicos y sociales con potencial influencia en las dinámicas demográficas de las razas locales. Los datos recogidos los analizamos mediante distintas técnicas estadísticas multivariantes como el análisis discriminante y la regresión logística. Encontramos que los factores que afectan a la viabilidad de las razas locales en Europa son muy heterogéneos. Un resultado reseñable fue que los ganaderos de algunos países no consideran que la explotación de su raza tenga un alto valor social. Este hecho vuelve a poner de manifiesto la importancia de desarrollar programas Europeos de concienciación sobre la importancia de las funciones que cumplen las razas locales. Además los países analizados presentaron una alta variabilidad en cuanto a la importancia de los mercados locales en la distribución de los productos y en cuanto al porcentaje en propiedad del total de los pastos usados en las explotaciones. Este estudio reflejó la variabilidad de los sistemas y medios de producción (en el sentido socioeconómico, técnico y ecológico) que existe en Europa. Por ello hay que ser cautos en la implementación de las políticas comunes en los diferentes países. También encontramos que la variabilidad dentro de los países puede ser elevada debido a las diferencias entre razas, lo que implica que las políticas nacionales deber ser suficientemente flexibles para adaptarse a las peculiaridades de cada una de las razas. Por otro lado, encontramos una serie de factores comunes a la viabilidad de las razas en los distintos países; la edad de los ganaderos, la colaboración entre ellos y la apreciación social de las funciones culturales, medioambientales y sociales del ganado local. El envejecimiento de los ganaderos de razas locales no es solo un problema de falta de transferencia generacional, sino que también puede suponer una actitud más negativa hacia la inversión en las actividades ganaderas y en una menor capacidad de adaptación a los cambios del sector. La capacidad de adaptación de los ganaderos es un factor crucial en la viabilidad de las razas locales. Las estrategias y políticas de conservación comunes deben incluir las variables comunes a la viabilidad de las razas manteniendo flexibilidad suficiente para adaptarse a las especificidades nacionales. Estas estrategias y políticas deberían ir más allá de compensación económica a los ganaderos de razas locales por la menor productividad de sus razas. Las herramientas para la toma de decisiones ayudan a generar una visión amplia de la conservación y desarrollo de las razas locales. Estas herramientas abordan el diseño de estrategias de conservación y desarrollo de forma sistemática y estructurada. En la tercera parte de la tesis usamos una de estas herramientas, el análisis DAFO (Debilidades, Amenazas, Fortalezas y Oportunidades), con este propósito, reconociendo que la conservación de RGADs depende de los ganaderos. Desarrollamos un análisis DAFO cuantitativo y lo aplicamos a trece razas locales de ganado vacuno de seis países europeos en el contexto del proyecto de colaboración mencionado anteriormente. El método tiene cuatro pasos: 1) la definición del sistema; 2) la identificación y agrupación de los factores influyentes; 3) la cuantificación de la importancia de dichos factores y 4) la identificación y priorización de estrategias. Identificamos los factores utilizando multitud de agentes (multi-stakeholder appproach). Una vez determinados los factores se agruparon en una estructura de tres niveles. La importancia relativa de los cada uno de los factores para cada raza fue determinada por grupos de expertos en RGADs de los países integrados en el citado proyecto. Finalmente, desarrollamos un proceso de cuantificación para identificar y priorizar estrategias. La estructura de agrupación de factores permitió analizar el problema de la conservación desde el nivel general hasta el concreto. La unión de análisis específicos de cada una de las razas en un análisis DAFO común permitió evaluar la adecuación de las estrategias a cada caso concreto. Identificamos un total de 99 factores. El análisis reveló que mientras los factores menos importantes son muy consistentes entre razas, los factores y estrategias más relevantes son muy heterogéneos. La idoneidad de las estrategias fue mayor a medida que estas se hacían más generales. A pesar de dicha heterogeneidad, los factores influyentes y estrategias más importantes estaban ligados a aspectos positivos (fortalezas y oportunidades) lo que implica que el futuro de estas razas es prometedor. Los resultados de nuestro análisis también confirmaron la gran relevancia del valor cultural de estas razas. Las factores internos (fortalezas y debilidades) más importantes estaban relacionadas con los sistemas de producción y los ganaderos. Las oportunidades más relevantes estaban relacionadas con el desarrollo y marketing de nuevos productos mientras que las amenazas más importantes se encontraron a la hora de vender los productos actuales. Este resultado implica que sería fructífero trabajar en la motivación y colaboración entre ganaderos así como, en la mejora de sus capacidades. Concluimos que las políticas comunes europeas deberían centrarse en aspectos generales y ser los suficientemente flexibles para adaptarse a las singularidades de los países y las razas. Como ya se ha mencionado, los ganaderos juegan un papel esencial en la conservación y desarrollo de las razas autóctonas. Por ello es relevante entender que implicación puede tener la heterogeneidad de los mismos en la viabilidad de una raza. En la cuarta parte de la tesis hemos identificado tipos de ganaderos con el fin de entender cómo la relación entre la variabilidad de sus características socioeconómicas, los perfiles de las ganaderías y las dinámicas de las mismas. El análisis se ha realizado en un contexto sociológico, aplicando los conceptos de capital cultural y económico. Las tipologías se han determinado en función de factores socioeconómicos y culturales indicadores del capital cultural y capital económico de un individuo. Nuestro objetivo era estudiar si la tipología socioeconómica de los ganaderos afecta al perfil de su ganadería y a las decisiones que toman. Entrevistamos a 85 ganaderos de la raza Avileña-Negra Ibérica (ANI) y utilizamos los resultados de dichas entrevistas para ilustrar y testar el proceso. Definimos los tipos de ganaderos utilizando un análisis de clúster jerarquizado con un grupo de variables canónicas que se obtuvieron en función de cinco factores socioeconómicos: el nivel de educación del ganadero, el año en que empezó a ser ganadero de ANI, el porcentaje de los ingresos familiares que aporta la ganadería, el porcentaje de propiedad de la tierra de la explotación y la edad del ganadero. La tipología de los ganaderos de ANI resultó ser más compleja que en el pasado. Los resultados indicaron que los tipos de ganaderos variaban en muchos aspectos socioeconómicos y en los perfiles de sus Integration of socioeconomic and genetic aspects involved in the conservation of animal genetic resources 9 ganaderías. Los tipos de ganaderos determinados toman diferentes decisiones en relación a la modificación del tamaño de su ganadería y a sus objetivos de selección. Por otro lado, reaccionaron de forma diferente ante un hipotético escenario de reducción de las compensaciones económicas que les planteamos. En este estudio hemos visto que el capital cultural y el económico interactúan y hemos explicado como lo hacen en los distintos tipos de ganaderos. Por ejemplo, los ganaderos que poseían un mayor capital económico, capital cultural formal y capital cultural adquirido sobre la raza, eran los ganaderos cuyos animales tenían una mayor demanda por parte de otros ganaderos, lo cual podría responder a su mayor prestigio social dentro de la raza. Uno de los elementos claves para el futuro de la raza es si este prestigio responde a una superioridad genética de las animales. Esto ocurriría si los ganaderos utilizaran las herramientas que tienen a su disposición a la hora de seleccionar animales. Los tipos de ganaderos identificados mostraron también claras diferencias en sus formas de colaboración y en su reacción a una hipotética variación de las compensaciones económicas. Aunque algunos tipos de ganaderos mostraron un bajo nivel de dependencia a estas compensaciones, la mayoría se manifestaron altamente dependientes. Por ello cualquier cambio drástico en la política de ayudas puede comprometer el desarrollo de las razas autóctonas. La adaptación las políticas de compensaciones económicas a la heterogeneidad de los ganaderos podría aumentar la eficacia de las mismas por lo que sería interesante explorar posibilidades a este respecto. Concluimos destacando la necesidad de desarrollar políticas que tengan en cuenta la heterogeneidad de los ganaderos. Finalmente abordamos el estudio de la estructura genética de poblaciones ganaderas. Las decisiones de los ganaderos en relación a la selección de sementales y su número de descendientes configuran la estructura demográfica y genética de las razas. En la actualidad existe un interés renovado por estudiar las estructuras poblacionales debido a la influencia potencial de su estratificación sobre la predicción de valores genómicos y/o los análisis de asociación a genoma completo. Utilizamos dos métodos distintos, un algoritmo de clústeres basados en teoría de grafos (GCA) y un algoritmo de clustering bayesiano (STRUCTURE) para estudiar la estructura genética de la raza ANI. Prestamos especial atención al efecto de la presencia de parientes cercanos en la población y de la diferenciación genética entre subpoblaciones sobre el análisis de la estructura de la población. En primer lugar evaluamos el comportamiento de los dos algoritmos en poblaciones simuladas para posteriormente analizar los genotipos para 17 microsatélites de 13343 animales de 57 ganaderías distintas de raza ANI. La ANI es un ejemplo de raza con relaciones complejas. Por otro lado, utilizamos el archivo de pedigrí de la raza para estudiar el flujo de genes, calculando, entre otras cosas, la contribución de cada ganadería a la constitución genética de la raza. En el caso de las poblaciones simuladas, cuando el FST entre subpoblaciones fue suficientemente alto, ambos algoritmos, GCA y STRUCTURE, identificaron la misma estructura genética independientemente de que existieran o no relaciones familiares. Por el contrario, cuando el grado de diferenciación entre poblaciones fue bajo, el STRUCTURE identificó la estructura familiar mientras que GCA no permitió obtener ningún resultado concluyente. El GCA resultó ser un algoritmo más rápido y eficiente para de inferir la estructura genética en poblaciones con relaciones complejas. Este algoritmo también puede ser usado para reducir el número de clústeres a testar con el STRUTURE. En cuanto al análisis de la población de ANI, ambos algoritmos describieron la misma estructura, lo cual sugiere que los resultados son robustos. Se identificaron tres subpoblaciones diferenciadas que pudieran corresponderse con tres linajes distintos. Estos linajes estarían directamente relacionados con las ganaderías que han tenido una mayor contribución a la constitución genética de la raza. Por otro lado, hay un conjunto muy numeroso de individuos con una mezcla de orígenes. La información molecular describe una estructura estratificada de la población que se corresponde con la evolución demográfica de la raza. Es esencial analizar en mayor profundidad la composición de este último grupo de animales para determinar cómo afecta a la variabilidad genética de la población de ANI. SUMMARY Summary Livestock sector is gradually dominated by intensive and specialized systems where the production environment is controlled and the production traits are the main criteria for the selection of species and breeds. In the meantime, the traditional use of domestic animals for draught work, clothes and manure has been replaced by industrial products. As a consequence of both these changes, the intensively selected breeds closely linked with high-input highoutput production systems have displaced many native breeds where the selection has practically ceased or been very mild. People are now more aware of the state of endangerment among the native breeds and the previously ignored values of livestock are gaining recognition. For some decades now, the economic, socio-cultural, environmental and food security function of livestock breeds have been accepted worldwide and their loss has been recognized as a major problem. Therefore, the conservation of farm animal genetic resources (FAnGR) has been recommended. The conservation of FAnGR is controversial due to the complexity of the evaluation of its functions. This evaluation is difficult due to the nature of FAnGR both as private and public good. As some economists have highlighted, livestock animals are private goods, however, they are also public goods by their functions. Therefore, there is a need to increase the knowledge about the value of all livestock functions since to support the decision-making for the sustainable conservation and breeding of livestock. This is not straightforward since the relative importance of livestock functions depends on time, place, species and breed. Since livestock play a variety of roles, their production is driven by interrelated and everchanging economic, technical, environmental, social, cultural and political elements involving an enormous range of stakeholders. Not only FAnGR functions but also the importance of factors affecting the development and conservation of FAnGR can be very different across geographical areas. Furthermore, heterogeneity can be found even within breeds. Local breeds are nowadays raised by highly diverse farmers in equally diverse farms. It is quite reasonable to think that farmer is the major actor in the in situ conservation of livestock breeds. Thus, there is a need to understand the farmers’ motivations, decision making processes and the impact of their decisions on the genetic structure of breeds. In this PhD thesis we explore different social, economic and genetic aspects involved in the conservation of local cattle breeds, i.e. FAnGR, in Europe seeking to contribute to the scientific understanding of this complex issue. We aim to achieve a comprehensive view of the processes involved in the conservation and development of local cattle breeds and have made special efforts in discussing the implications of the research results in this respect. The final outcome of the thesis is to illustrate how quantitative methods can be exploited in designing and establishing sound strategies and programmes for the conservation and development of local livestock breeds. Firstly we explored the public non-market attributes of the total economic value (TEV) of livestock, using the Spanish Alistana-Sanabresa (AS) cattle breed as a case study. Total economic value of any good comprises both use and non-use components, where the latter include option, bequest and existence values. For livestock, the direct use values are mainly stemming from production outputs. Indirect use values relate to the role of livestock as a maintainer of rural culture and landscape. The option value is related to the potential use of livestock, the bequest values relate to the value associated with the inheritance of the resources to future generation and the existence values relate to the utility perceived by people from knowing that specific resources exist. We aimed to determine the relative importance of the non-market components of the TEV of the AS breed, the socio-economic variables that influence how people value the different components of TEV and to assess the implications of the Spanish national conservation strategy for the AS breed. To do so, we used a choice experiment (CE) approach and applied the technique to assess people’s willingness to pay (WTP) for the conservation of AS breed. The use of CE allows the valuation of the individual components of TEV for a given good. We analysed the choice data using a random parameter logit (RPL) model. AS breed was found to have a significant public good value. Its most important values were related to the indirect use value due to the maintenance of Zamorian culture and the existence value (both represent over 80% of its TEV). There were several socioeconomic variables influencing people’s valuation of the public service of the breed. In the case of AS breed, the place of living (city or rural area), having seen animals of the breed, having eaten breed products and the respondents’ attitude towards economic development – environment conflicts do influence people’s WTP for AS conservation. We also found that people do not have a complete picture of all the functions and roles that AS breed as AnGR. Therefore, the actions for increasing awareness of AS should go to that direction. The farmers will need incentives to exploit some of the public goods values and maintain the breed population size at socially desirable levels. One such mechanism could be related to the development of agritourism, which would enhance the private good value and provide an important addition to the conservation and utilisation strategy. However, the farmers need a serious evaluation on how to invest in niche product development or how to improve product quality and brand recognition. Using the understanding on the importance of the public function of local cattle we tried to depict the current diversity regarding technical, economic and social factors found in local cattle farming across Europe. To do so we focused in an international collaborative project on the case of fifteen local cattle breeds in eight European countries. We investigated the variation among the countries to detect the common key elements, which affect the viability of local breeds. We surveyed with interviews a total of 355 farms across the fifteen breeds. We used the planned herd size changes by the farmer as an indicator of breed viability. The questionnaire included several economic, technical and social aspects with potential influence on breeds’ demographic trends. We analysed the data using multivariate statistical techniques, such as discriminat analysis and logistic regression. The factors affecting a local breed’s viability were highly heterogeneous across Europe. In some countries, farmers did not recognise any high social value attached to keeping a local cattle breed. Hence there is a need to develop communication programmes across EU countries making people aware about the diversity and importance of values associated to raising local breeds. The countries were also very variable regarding the importance of local markets and the percentage of farm land owned by the farmers. Despite the country specificities, there were also common factors affecting the breed viability across Europe. The factors were from different grounds, from social, such as the age of the farmer and the social appreciation of their work, to technicalorganizational, such as the farmers’ attitude to collaborating with each other. The heterogeneity found reflects the variation in breeding systems and production environment (in the socioeconomic, technical and ecological sense) present in Europe. Therefore, caution should be taken in implementing common policies at the country level. Variability could also be rather high within countries due to breed specificities. Therefore, the national policies should be flexible to adapt to the specificities. The variables significantly associated with breed viability should be positively incorporated in the conservation strategies, and considered in developing common and/or national policies. The strategy preparation and policy planning should go beyond the provision of a general economic support to compensate farmers for the lower profitability of local breeds. Of particular interest is the observation that the opportunity for farmer collaboration and the appreciation by the society of the cultural, environmental and social role of local cattle farming were positively associated with the breed survival. In addition, farmer's high age is not only a problem of poor generation transfer but it is also a problem because it might lead to a lower attitude to investing in farming activities and to a lower ability to adapt to environment changes. The farmers’ adaptation capability may be a key point for the viability of local breeds. Decision making tools can help to get a comprehensive view on the conservation and development of local breeds. It allows us to use a systematic and structured approach for identifying and prioritizing conservation and development strategies. We used SWOT (Strengths, Weaknesses Opportunities and Threats) analysis for this purpose and recognized that many conservation and development projects rely on farmers. We developed a quantified SWOT method and applied it in the aforementioned collaborative research to a set of thirteen cattle breeds in six European countries. The method has four steps: definition of the system, identification and grouping of the driving factors, quantification of the importance of driving factors and identification and prioritization of the strategies. The factors were determined following a multi-stakeholder approach and grouped with a three level structure. FAnGR expert groups ranked the factors and a quantification process was implemented to identify and prioritize strategies. The structure of the SWOT analysis allowed analyzing the conservation problem from general down to specific perspectives. Joining breed specific analyses into a common SWOT analysis permitted comparison of breed cases across countries. We identified 99 driving factors across breeds. The across breed analysis revealed that irrelevant factors were consistent. There was high heterogeneity among the most relevant factors and strategies. The strategies increased eligibility as they lost specificity. Although the situation was very heterogeneous, the most promising factors and strategies were linked to the positive aspects (Strengths and Opportunities). Therefore, the future of the studied local breed is promising. The results of our analysis also confirmed the high relevance of the cultural value of the breeds. The most important internal factors (strengths and weaknesses) were related farmers and production systems. The most important opportunities were found in developing and marketing new products, while the most relevant threats were found in selling the current conventional products. In this regard, it should be fruitful to work on farmers’ motivation, collaboration, and capacity building. We conclude that European policies should focus on general aspects and be flexible enough to be adapted to the country and breed specificities. As mentioned, farmers have a key role in the conservation and development of a local cattle breed. Therefore, it is very relevant to understand the implications of farmer heterogeneity within a breed for its viability. In the fourth part of the thesis, we developed a general farmer typology to help analyzing the relations between farmer features and farm profiles, herd dynamics and farmers’ decision making. In the analysis we applied and used the sociological framework of economic and cultural capital and studied how the determined farmer types were linked to farm profiles and breeding decisions, among others. The typology was based on measurable socioeconomic factors indicating the economic and cultural capital of farmers. A group of 85 farmers raising the Spanish Avileña-Negra Ibérica (ANI) local cattle breed was used to illustrate and test the procedure. The farmer types were defined by a hierarchical cluster analysis with a set of canonical variables derived from the following five the socioeconomic factors: the formal educational level of the farmer, the year the farmer started keeping the ANI breed, the percentage of the total family income covered by the farm, the percentage of the total farm land owned by the farmer and the farmer’s age. The present ANI farmer types were much more complex than what they were in the past. We found that the farmer types differed in many socioeconomic aspects and in the farms profile. Furthermore, the types also differentiate farmers with respect to decisions about changing the farm size, breeding aims and stated reactions towards hypothetical subsidy variation. We have verified that economic and cultural capitals are not independent and further showed how they are interacting in the different farmer types. The farmers related to the types with high economic, institutionalized and embodied cultural capitals had a higher demand of breeding animals from others farmers of the breed, which may be related to the higher social prestige within the breed. One of the key implications of this finding for the future of the breed is whether or not the prestige of farmers is related to genetic superiority of their animals, what is to say, that it is related with a sound use of tools that farmers have available to make selection decisions. The farmer types differed in the form of collaboration and in the reactions to the hypothetical variation in subsidies. There were farmers with low dependency on subsidies, while most of them are highly dependent on subsidies. Therefore, any drastic change in the subsidy programme might have influence on the development of local breeds. The adaptation of these programme to the farmers’ heterogeneity might increase its efficacy, thus it would be interesting to explore ways of doing it. We conclude highlighting the need to have a variety of policies, which take into account the heterogeneity among the farmers. To finish we dealt with the genetic structure of livestock populations. Farmers’ decisions on the breeding animals and their progeny numbers shape the demographic and genetic structure of the breeds. Nowadays there is a renovated interest in studying the population structure since it can bias the prediction of genomic breeding values and genome wide association studies. We determined the genetic structure of ANI breed using two different methods, a graphical clustering algorithm (GCA) and a Bayesian clustering algorithm (STRUCTURE) were used. We paid particular attention to the influence that the presence of closely related individuals and the genetic differentiation of subpopulations may have on the inferences about the population structure. We first evaluated the performance of the algorithms in simulated populations. Then we inferred the genetic structure of the Spanish cattle breed ANI analysing a data set of 13343 animals (genotyped for 17 microsatellites) from 57 herds. ANI breed is an example of a population with complex relationships. We used the herdbook to study the gene flow, estimation among other things, the contribution of different herds to the genetic composition of the ANI breed. For the simulated scenarios, when FST among subpopulations was sufficiently high, both algorithms consistently inferred the correct structure regardless of the presence of related individuals. However, when the genetic differentiation among subpopulations was low, STRUCTURE identified the family based structure while GCA did not provide any consistent picture. The GCA was a fast and efficient method to infer genetic structure to determine the hidden core structure of a population with complex history and relationships. GCA could also be used to narrow down the number of clusters to be tested by STRUCTURE. Both, STRUCTURE and GCA describe a similar structure for the ANI breed suggesting that the results are robust. ANI population was found to have three genetically differentiated clusters that could correspond to three genetic lineages. These are directly related to the herds with a major contribution to the breed. In addition, ANI breed has also a large pool made of individuals with an admixture of origins. The genetic structure of ANI, assessed by molecular information, shows a stratification that corresponds to the demographic evolution of the breed. It will be of great importance to learn more about the composition of the pool and study how it is related to the existing genetic variability of the breed.

Facing the climate change challenges in the mining and mineral industry as providers of a sustainable manufacturing process

A sustainable manufacturing process must rely on an also sustainable raw materials and energy supply. This paper is intended to show the results of the studies developed on sustainable business models for the minerals industry as a fundamental previous part of a sustainable manufacturing process. As it has happened in other economic activities, the mining and minerals industry has come under tremendous pressure to improve its social, developmental, and environmental performance. Mining, refining, and the use and disposal of minerals have in some instances led to significant local environmental and social damage. Nowadays, like in other parts of the corporate world, companies are more routinely expected to perform to ever higher standards of behavior, going well beyond achieving the best rate of return for shareholders. They are also increasingly being asked to be more transparent and subject to third-party audit or review, especially in environmental aspects. In terms of environment, there are three inter-related areas where innovation and new business models can make the biggest difference: carbon, water and biodiversity. The focus in these three areas is for two reasons. First, the industrial and energetic minerals industry has significant footprints in each of these areas. Second, these three areas are where the potential environmental impacts go beyond local stakeholders and communities, and can even have global impacts, like in the case of carbon. So prioritizing efforts in these areas will ultimately be a strategic differentiator as the industry businesses continues to grow. Over the next forty years, world?s population is predicted to rise from 6.300 million to 9.500 million people. This will mean a huge demand of natural resources. Indeed, consumption rates are such that current demand for raw materials will probably soon exceed the planet?s capacity. As awareness of the actual situation grows, the public is demanding goods and services that are even more environmentally sustainable. This means that massive efforts are required to reduce the amount of materials we use, including freshwater, minerals and oil, biodiversity, and marine resources. It?s clear that business as usual is no longer possible. Today, companies face not only the economic fallout of the financial crisis; they face the substantial challenge of transitioning to a low-carbon economy that is constrained by dwindling natural resources easily accessible. Innovative business models offer pioneering companies an early start toward the future. They can signal to consumers how to make sustainable choices and provide reward for both the consumer and the shareholder. Climate change and carbon remain major risk discontinuities that we need to better understand and deal with. In the absence of a global carbon solution, the principal objective of any individual country should be to reduce its global carbon emissions by encouraging conservation. The mineral industry internal response is to continue to focus on reducing the energy intensity of our existing operations through energy efficiency and the progressive introduction of new technology. Planning of the new projects must ensure that their energy footprint is minimal from the start. These actions will increase the long term resilience of the business to uncertain energy and carbon markets. This focus, combined with a strong demand for skills in this strategic area for the future requires an appropriate change in initial and continuing training of engineers and technicians and their awareness of the issue of eco-design. It will also need the development of measurement tools for consistent comparisons between companies and the assessments integration of the carbon footprint of mining equipments and services in a comprehensive impact study on the sustainable development of the Economy.

Effects of irrigation and time of application on the yield and quality of cv. Cabernet sauvignon in a warm climate

Mediterranean climate is characterized by hot summer, high evapotranspiration rates, and scarce precipitations (400 mm per year) during grapevine cycle. These extremely dry conditions affect vineyard productivity and sustainability. Supplementary irrigation is a needed practice in order to maintain yield and quality. Almost all Spanish grape growing regions are characterized by these within this context, especially in the center region, where this study was performed. The main objective of this work was to study the influence of irrigation on yield and quality. For this aim, we applied different levels of irrigation (mm of water applied) during different stages of growth and berry maturity. Four experimental treatments were applied considering the amount of water and the moment of the application: T1: Water irrigation (420 mm) applied from bloom to maturity. T2: Corresponded to the traditional irrigation scheduling, from preveraison to maturity (154 mm). T3: Water irrigation from bloom to preveraison, and water deficit from veraison to maturity (312 mm). T4: Irrigation applied from preveraison to maturity (230 mm) Experimental vineyard, cv. Cabernet Sauvignon, was located in a commercial vineyard (Bodegas Licinia S.L.) in the hot region of Morata de Tajuña (Madrid). The trial was performed during 2010 and 2011 seasons. Our results showed that yield increased from 2010 to 2011 in the treatments with a higher amount of water appli ed, T1 and T3 (24 and 10 % of yield increase respectively). This was mainly due to an increase in bud fertility (nº of bunches per shoot). Furthermore, sugar content was higher in T3 (27.3 ºBrix), followed by T2 (27 ºBrix). By contrast, T4 (irrigation from veraison) presented the lowest solid soluble concentration and the highest acidity. These results suggest that grapevine has an intrinsic capacity to adapt to its environment. However, this adaptation capacity should be evaluated considering the sensibility of quality parameters during the maturity period (acidity, pH, aroma, color...) and its impact on yield. Here, we demonstrated that a higher amount of water irrigation applied was no linked to a negative effect on quality.

Analysis of the discharge capacity of radial-gated spillways using CFD and ANN - Oliana Dam case study.

The paper focuses on the analysis of radial-gated spillways, which is carried out by the solution of a numerical model based on the finite element method (FEM). The Oliana Dam is considered as a case study and the discharge capacity is predicted both by the application of a level-set-based free-surface solver and by the use of traditional empirical formulations. The results of the analysis are then used for training an artificial neural network to allow real-time predictions of the discharge in any situation of energy head and gate opening within the operation range of the reservoir. The comparison of the results obtained with the different methods shows that numerical models such as the FEM can be useful as a predictive tool for the analysis of the hydraulic performance of radial-gated spillways.

Implementation of the Heated Pulsed Theory using actively heated fiber optics: measurements of soil volumetric water content and soil volumetric heat capacity

Existe una creciente necesidad de hacer el mejor uso del agua para regadío. Una alternativa eficiente consiste en la monitorización del contenido volumétrico de agua (θ), utilizando sensores de humedad. A pesar de existir una gran diversidad de sensores y tecnologías disponibles, actualmente ninguna de ellas permite obtener medidas distribuidas en perfiles verticales de un metro y en escalas laterales de 0.1-1,000 m. En este sentido, es necesario buscar tecnologías alternativas que sirvan de puente entre las medidas puntuales y las escalas intermedias. Esta tesis doctoral se basa en el uso de Fibra Óptica (FO) con sistema de medida de temperatura distribuida (DTS), una tecnología alternativa de reciente creación que ha levantado gran expectación en las últimas dos décadas. Específicamente utilizamos el método de fibra calentada, en inglés Actively Heated Fiber Optic (AHFO), en la cual los cables de Fibra Óptica se utilizan como sondas de calor mediante la aplicación de corriente eléctrica a través de la camisa de acero inoxidable, o de un conductor eléctrico simétricamente posicionado, envuelto, alrededor del haz de fibra óptica. El uso de fibra calentada se basa en la utilización de la teoría de los pulsos de calor, en inglés Heated Pulsed Theory (HPP), por la cual el conductor se aproxima a una fuente de calor lineal e infinitesimal que introduce calor en el suelo. Mediante el análisis del tiempo de ocurrencia y magnitud de la respuesta térmica ante un pulso de calor, es posible estimar algunas propiedades específicas del suelo, tales como el contenido de humedad, calor específico (C) y conductividad térmica. Estos parámetros pueden ser estimados utilizando un sensor de temperatura adyacente a la sonda de calor [método simple, en inglés single heated pulsed probes (SHPP)], ó a una distancia radial r [método doble, en inglés dual heated pulsed probes (DHPP)]. Esta tesis doctoral pretende probar la idoneidad de los sistemas de fibra óptica calentada para la aplicación de la teoría clásica de sondas calentadas. Para ello, se desarrollarán dos sistemas FO-DTS. El primero se sitúa en un campo agrícola de La Nava de Arévalo (Ávila, España), en el cual se aplica la teoría SHPP para estimar θ. El segundo sistema se desarrolla en laboratorio y emplea la teoría DHPP para medir tanto θ como C. La teoría SHPP puede ser implementada con fibra óptica calentada para obtener medidas distribuidas de θ, mediante la utilización de sistemas FO-DTS y el uso de curvas de calibración específicas para cada suelo. Sin embargo, la mayoría de aplicaciones AHFO se han desarrollado exclusivamente en laboratorio utilizando medios porosos homogéneos. En esta tesis se utiliza el programa Hydrus 2D/3D para definir tales curvas de calibración. El modelo propuesto es validado en un segmento de cable enterrado en una instalación de fibra óptica y es capaz de predecir la respuesta térmica del suelo en puntos concretos de la instalación una vez que las propiedades físicas y térmicas de éste son definidas. La exactitud de la metodología para predecir θ frente a medidas puntuales tomadas con sensores de humedad comerciales fue de 0.001 a 0.022 m3 m-3 La implementación de la teoría DHPP con AHFO para medir C y θ suponen una oportunidad sin precedentes para aplicaciones medioambientales. En esta tesis se emplean diferentes combinaciones de cables y fuentes emisoras de calor, que se colocan en paralelo y utilizan un rango variado de espaciamientos, todo ello en el laboratorio. La amplitud de la señal y el tiempo de llegada se han observado como funciones del calor específico del suelo. Medidas de C, utilizando esta metodología y ante un rango variado de contenidos de humedad, sugirieron la idoneidad del método, aunque también se observaron importantes errores en contenidos bajos de humedad de hasta un 22%. La mejora del método requerirá otros modelos más precisos que tengan en cuenta el diámetro del cable, así como la posible influencia térmica del mismo. ABSTRACT There is an increasing need to make the most efficient use of water for irrigation. A good approach to make irrigation as efficient as possible is to monitor soil water content (θ) using soil moisture sensors. Although, there is a broad range of different sensors and technologies, currently, none of them can practically and accurately provide vertical and lateral moisture profiles spanning 0-1 m depth and 0.1-1,000 m lateral scales. In this regard, further research to fulfill the intermediate scale and to bridge single-point measurement with the broaden scales is still needed. This dissertation is based on the use of Fiber Optics with Distributed Temperature Sensing (FO-DTS), a novel approach which has been receiving growing interest in the last two decades. Specifically, we employ the so called Actively Heated Fiber Optic (AHFO) method, in which FO cables are employed as heat probe conductors by applying electricity to the stainless steel armoring jacket or an added conductor symmetrically positioned (wrapped) about the FO cable. AHFO is based on the classic Heated Pulsed Theory (HPP) which usually employs a heat probe conductor that approximates to an infinite line heat source which injects heat into the soil. Observation of the timing and magnitude of the thermal response to the energy input provide enough information to derive certain specific soil thermal characteristics such as the soil heat capacity, soil thermal conductivity or soil water content. These parameters can be estimated by capturing the soil thermal response (using a thermal sensor) adjacent to the heat source (the heating and the thermal sources are mounted together in the so called single heated pulsed probe (SHPP)), or separated at a certain distance, r (dual heated pulsed method (DHPP) This dissertation aims to test the feasibility of heated fiber optics to implement the HPP theory. Specifically, we focus on measuring soil water content (θ) and soil heat capacity (C) by employing two types of FO-DTS systems. The first one is located in an agricultural field in La Nava de Arévalo (Ávila, Spain) and employ the SHPP theory to estimate θ. The second one is developed in the laboratory using the procedures described in the DHPP theory, and focuses on estimating both C and θ. The SHPP theory can be implemented with actively heated fiber optics (AHFO) to obtain distributed measurements of soil water content (θ) by using reported soil thermal responses in Distributed Temperature Sensing (DTS) and with a soil-specific calibration relationship. However, most reported AHFO applications have been calibrated under laboratory homogeneous soil conditions, while inexpensive efficient calibration procedures useful in heterogeneous soils are lacking. In this PhD thesis, we employ the Hydrus 2D/3D code to define these soil-specific calibration curves. The model is then validated at a selected FO transect of the DTS installation. The model was able to predict the soil thermal response at specific locations of the fiber optic cable once the surrounding soil hydraulic and thermal properties were known. Results using electromagnetic moisture sensors at the same specific locations demonstrate the feasibility of the model to detect θ within an accuracy of 0.001 to 0.022 m3 m-3. Implementation of the Dual Heated Pulsed Probe (DPHP) theory for measurement of volumetric heat capacity (C) and water content (θ) with Distributed Temperature Sensing (DTS) heated fiber optic (FO) systems presents an unprecedented opportunity for environmental monitoring. We test the method using different combinations of FO cables and heat sources at a range of spacings in a laboratory setting. The amplitude and phase-shift in the heat signal with distance was found to be a function of the soil volumetric heat capacity (referred, here, to as Cs). Estimations of Cs at a range of θ suggest feasibility via responsiveness to the changes in θ (we observed a linear relationship in all FO combinations), though observed bias with decreasing soil water contents (up to 22%) was also reported. Optimization will require further models to account for the finite radius and thermal influence of the FO cables, employed here as “needle probes”. Also, consideration of the range of soil conditions and cable spacing and jacket configurations, suggested here to be valuable subjects of further study and development.

Slow fashion and sustainability in Spain: How can local manufacturing improve sustainability and how do consumers respond?

"Slow Fashion" attempts to offset the demand for fast fashion and mass production (Fletcher, 2007). Consumers' response to sustainability-based practices is a limited discourse and studies for slow fashion concept are scarce. This study thus aims to enlighten the subject of how slow fashion concept could improve local economies and how Spanish consumers respond to such initiatives. This paper is based on an exploratory qualitative research for which focus group interviews including three group discussions with Spanish consumers were held. The data was examined by constant comparison analysis to present consumer insights. Moreover, a case study was conducted with a Spanish apparel brand. Saint Brissant was chosen since it manufactures in Spain to (i) ensure its products? high quality and (ii) to empower Spanish economy. This paper provides empirical insights. Even though local manufacturing was perceived to have a higher quality, Spanish consumers? behavioural intentions of using local brands were not high.Self-interest, mainly price and design, was recorded as the most influential purchase criteria. Furthermore, Saint Brissant case demonstrated that local manufacturing could boost local economies by creating workforce. However, governmental subsidies should be rearranged and consumers? perceptions should be improved to support local manufacturers in Spain.