Packaging and testing of fiber Bragg gratings for use as strain sensor for rock specimens

This paper reports a packaging and calibration procedure for surface mounting of fiber Bragg grating (FBG) sensors to measure strain in rocks. The packaging of FBG sensors is performed with glass fiber and polyester resin, and then subjected to tensile loads in order to obtain strength and deformability parameters, necessaries to assess the mechanical performance of the sensor packaging. For a specific package, an optimal curing condition has been found, showing good repeatability and adaptability for non-planar surfaces, such as occurs in rock engineering. The successfully packaged sensors and electrical strain gages were attached to standard rock specimens of gabbro. Longitudinal and transversal strains under compression loads were measured with both techniques, showing that response of FBG sensors is linear and reliable. An analytical model is used to characterize the influences of rock substrate and FBG packaging in strain transmission. As a result, we obtained a sensor packaging for non-planar and complex natural material under acceptable sensitivity suitable for very small strains as occurs in hard rocks.

La estabilidad del frente de excavación de un túnel en terrenos heterogéneos o con un criterio de rotura no-lineal

El frente de un túnel puede colapsar si la presión aplicada sobre el es inferior a un valor limite denominado presión “critica” o “de colapso”. En este trabajo se desarrolla y presenta un mecanismo de rotura rotacional generado punto a punto para el cálculo de la presión de colapso del frente de túneles excavados en terrenos estratificados o en materiales que siguen un criterio de rotura nolineal. La solución propuesta es una solución de contorno superior en el marco del Análisis Límite y supone una generalización del mecanismo de rotura mas reciente existente en la bibliografía. La presencia de un terreno estratificado o con un criterio de rotura no-lineal implica una variabilidad espacial de las propiedades resistentes. Debido a esto, se generaliza el mecanismo desarrollado por Mollon et al. (2011b) para suelos, de tal forma que se puedan considerar valores locales del ángulo de rozamiento y de la cohesión. Además, la estratificación del terreno permite una rotura parcial del frente, por lo que se implementa esta posibilidad en el mecanismo, siendo la primera solución que emplea un mecanismo de rotura que se ajusta a la estratigrafía del terreno. Por otro lado, la presencia de un material con un criterio de rotura no-lineal exige introducir en el modelo, como variable de estudio, el estado tensional en el frente, el cual se somete al mismo proceso de optimización que las variables geométricas del mecanismo. Se emplea un modelo numérico 3D para validar las predicciones del mecanismo de Análisis Limite, demostrando que proporciona, con un esfuerzo computacional significativamente reducido, buenas predicciones de la presión critica, del tipo de rotura (global o parcial) en terrenos estratificados y de la geometría de fallo. El mecanismo validado se utiliza para realizar diferentes estudios paramétricos sobre la influencia de la estratigrafía en la presión de colapso. Igualmente, se emplea para elaborar cuadros de diseño de la presión de colapso para túneles ejecutados con tuneladora en macizos rocosos de mala calidad y para analizar la influencia en la estabilidad del frente del método constructivo. Asimismo, se lleva a cabo un estudio de fiabilidad de la estabilidad del frente de un túnel excavado en un macizo rocoso altamente fracturado. A partir de el se analiza como afectan las diferentes hipótesis acerca de los tipos de distribución y de las estructuras de correlación a los resultados de fiabilidad. Se investiga también la sensibilidad de los índices de fiabilidad a los cambios en las variables aleatorias, identificando las mas relevantes para el diseño. Por ultimo, se lleva a cabo un estudio experimental mediante un modelo de laboratorio a escala reducida. El modelo representa medio túnel, lo cual permite registrar el movimiento del material mediante una técnica de correlación de imágenes fotográficas. El ensayo se realiza con una arena seca y se controla por deformaciones mediante un pistón que simula el frente. Los resultados obtenidos se comparan con las estimaciones de la solución de Análisis Límite, obteniéndose un ajuste razonable, de acuerdo a la literatura, tanto en la geometría de rotura como en la presión de colapso. A tunnel face may collapse if the applied support pressure is lower than a limit value called the ‘critical’ or ‘collapse’ pressure. In this work, an advanced rotational failure mechanism generated ‘‘point-by-point” is developed to compute the collapse pressure for tunnel faces in layered (or stratified) grounds or in materials that follow a non-linear failure criterion. The proposed solution is an upper bound solution in the framework of limit analysis which extends the most advanced face failure mechanism in the literature. The excavation of the tunnel in a layered ground or in materials with a non-linear failure criterion may lead to a spatial variability of the strength properties. Because of this, the rotational mechanism recently proposed by Mollon et al. (2011b) for Mohr-Coulomb soils is generalized so that it can consider local values of the friction angle and of the cohesion. For layered soils, the mechanism needs to be extended to consider the possibility for partial collapse. The proposed methodology is the first solution with a partial collapse mechanism that can fit to the stratification. Similarly, the use of a nonlinear failure criterion introduces the need to introduce new parameters in the optimization problem to consider the distribution of normal stresses along the failure surface. A 3D numerical model is employed to validate the predictions of the limit analysis mechanism, demonstrating that it provides, with a significantly reduced computational effort, good predictions of critical pressure, of the type of collapse (global or partial) in layered soils, and of its geometry. The mechanism is then employed to conduct parametric studies of the influence of several geometrical and mechanical parameters on face stability of tunnels in layered soils. Similarly, the methodology has been further employed to develop simple design charts that provide the face collapse pressure of tunnels driven by TBM in low quality rock masses and to study the influence of the construction method. Finally, a reliability analysis of the stability of a tunnel face driven in a highly fractured rock mass is performed. The objective is to analyze how different assumptions about distributions types and correlation structures affect the reliability results. In addition, the sensitivity of the reliability index to changes in the random variables is studied, identifying the most relevant variables for engineering design. Finally, an experimental study is carried out using a small-scale laboratory model. The problem is modeled in half, cutting through the tunnel axis vertically, so that displacements of soil particles can be recorded by a digital image correlation technique. The tests were performed with dry sand and displacements are controlled by a piston that supports the soil. The results of the model are compared with the predictions of the Limit Analysis mechanism. A reasonable agreement, according to literature, is obtained between the shapes of the failure surfaces and between the collapse pressures observed in the model tests and computed with the analytical solution.