Vehicular traffic surveillance and road lane detection using radar interferometry

Speed enforcement on public roadways is an important issue in order to guarantee road security and to reduce the number and seriousness of traffic accidents. Traditionally, this task has been partially solved using radar and/or laser technologies and, more recently, using video-camera based systems. All these systems have significant shortcomings that have yet to be overcome. The main drawback of classical Doppler radar technology is that the velocity measurement fails when several vehicles are in the radars beam. Modern radar systems are able to measure speed and range between vehicle and radar. However, this is not enough to discriminate the lane where the vehicle is driving on. The limitation of several vehicles in the beam is overcome using laser technology. However, laser systems have another important limitation: They cannot measure the speed of several vehicles simultaneously. Novel video-camera systems, based on license plate identification, solve the previous drawbacks, but they have the problem that they can only measure average speed but never top-speed. This paper studies the feasibility of using an interferometric linear frequency modulated continuous wave radar to improve top-speed enforcement on roadways. Two different systems based on down-the-road and across-the-road radar configurations are presented. The main advantage of the proposed solutions is they can simultaneously measure speed, range, and lane of several vehicles, allowing the univocal identification of the offenders. A detailed analysis about the operation and accuracy of these solutions is reported. In addition, the feasibility of the proposed techniques has been demonstrated with simulations and real experiments using a Ka-band interferometric radar developed by our research group.

Tunable mechanical resonator with aluminum nitride piezoelectric

The electromechanical response of piezoelectrically-actuated AlN micromachined bridge resonators has been characterized using laser interferometry and electrical admittance measurements. We compare the response of microbridges with different dimensions and buckling (induced by the initial residual stress of the layers). The resonance frequencies are in good agreement with numerical simulations of the electromechanical behavior of the structures. We show that it is possible to perform a rough tuning of the resonance frequencies by allowing a determined amount of builtin stress in the microbridge during its fabrication. Once the resonator is made, a DC bias added to the AC excitation signal allows to fine-tune the frequency. Our microbridges yield a tuning factor of around 88 Hz/V for a 500 ?m-long microbridge.

Development of Efficient FPGA-Based Multi-Channel Phase Meters for IR-Interferometers

Infrared (IR) interferometry is a method for measuring the line-electron density of fusion plasmas. The significant performance achieved by FPGAs in solving digital signal processing tasks advocates the use of this type of technology in two-color IR interferometers of modern stellarators, such as the TJ-II (Madrid, Spain) and the future W7-X (Greifswald, Germany). In this work the implementation of a line-average electron density measuring system in an FPGA device is described. Several optimizations for multichannel systems are detailed and test results from the TJ-II as well as from a W7-X prototype are presented.

Desarrollo de Técnicas Interferométricas para Radares de Alta Resolución en Milimétricas

En esta tesis doctoral se aborda el desarrollo de técnicas interferométricas para radares de alta resolución en milimétricas. Específicamente, se centra en el desarrollo de técnicas para radares terrestres y en concreto aquellas relacionadas con el seguimiento, clasificación y generación de imágenes de blancos móviles. Aparte del desarrollo teórico y simulación de las diferentes técnicas, uno de los grandes retos de esta tesis es la verificación experimental de las mismas. Para este propósito, se empleará un prototipo de sensor radar interferométrico de muy alta resolución y de ondas milimétricas. El primer capítulo de la tesis realiza una pequeña introducción a las técnicas interferométricas y presenta los objetivos, motivación y organización del presente trabajo. El segundo capítulo hace una pequeña introducción a los radares interferométricos de alta resolución en milimétricas y presenta el sensor radar experimental con el que se llevarán a cabo la validación de las distintas técnicas presentadas. El tercer capítulo recoge las distintas técnicas interferométricas desarrolladas para el seguimiento y cálculo de la altura de blancos móviles en radares de alta resolución. Entre ellas se encuentran: el seguimiento de blancos móviles en sucesión de imágenes ISAR, el cálculo de altura de blancos en imágenes radar bidimensionales distancia-tiempo y su equivalente en imágenes distancia-Doppler. El cuarto capítulo presenta una aplicación de las técnicas interferométricas para la vigilancia de tráfico en carreteras. Se describirán dos configuraciones radar que permiten calcular la velocidad de todos los blancos iluminados por el radar identificando de manera unívoca a los blancos en función del carril por el que circulen. El quinto capítulo presenta técnicas interferométricas aplicadas a la vigilancia en entornos marítimos basadas en la generación de imágenes interferométricas. Para demostrar la viabilidad del uso de estas imágenes se ha desarrollado un simulador de blancos móviles extensos realistas. Abstract This Ph. D thesis deals with the development of radar interferometry techniques for high-resolution millimeter wave sensors. It focuses on the development of techniques for ground-based radars and specifically those related to monitoring, classification and imaging of moving targets. Apart from the theoretical development and simulation, another major technical challenge of this thesis is the experimental verification of the different techniques. For that purpuse, a very high resolution interferometric millimeter wave radar sensor is used. The first chapter of the thesis makes a brief introduction to the interferometric techniques and shows the goals, motivation and organization of this work. The second chapter provides a brief introduction to high resolution interferometric radars in millimeter waves and presents the experimental radar sensor which will be used for the validation of the various techniques presented. The third chapter presents the different interferometric techniques developed for monitoring and obtaining the height of moving targets in high resolution radars. Among them are: tracking of moving targets in a succession of ISAR images, targets height calculation using bidimensional range-time radar images and the equivalente technique using range-Doppler images. The fourth chapter presents the application of interferometric techniques for road traffic monitoring. Two radar configurations are described. Both of them are able to obtain the speed for simultaneuslly illuminated targets, and univocally identify each target based on the detected road lane. The fifth chapter presents the application of interferometric techniques to maritime surveillance based on interferometric imaging. To demonstrate the feasibility of the presented techniques a realistic simulator of extended moving targets has been developed.

Auscultación de presas de hormigón con láser escáner terrestre y modelización de las deformaciones del paramento

Se está produciendo en la geodesia un cambio de paradigma en la concepción de los modelos digitales del terreno, pasando de diseñar el modelo con el menor número de puntos posibles a hacerlo con cientos de miles o millones de puntos. Este cambio ha sido consecuencia de la introducción de nuevas tecnologías como el escáner láser, la interferometría radar y el tratamiento de imágenes. La rápida aceptación de estas nuevas tecnologías se debe principalmente a la gran velocidad en la toma de datos, a la accesibilidad por no precisar de prisma y al alto grado de detalle de los modelos. Los métodos topográficos clásicos se basan en medidas discretas de puntos que considerados en su conjunto forman un modelo; su precisión se deriva de la precisión en la toma singular de estos puntos. La tecnología láser escáner terrestre (TLS) supone una aproximación diferente para la generación del modelo del objeto observado. Las nubes de puntos, producto del escaneo con TLS, pasan a ser tratadas en su conjunto mediante análisis de áreas, de forma que ahora el modelo final no es el resultado de una agregación de puntos sino la de la mejor superficie que se adapta a las nubes de puntos. Al comparar precisiones en la captura de puntos singulares realizados con métodos taquimétricos y equipos TLS la inferioridad de estos últimos es clara; sin embargo es en el tratamiento de las nubes de puntos, con los métodos de análisis basados en áreas, se han obtenido precisiones aceptables y se ha podido considerar plenamente la incorporación de esta tecnología en estudios de deformaciones y movimientos de estructuras. Entre las aplicaciones del TLS destacan las de registro del patrimonio, registro de las fases en la construcción de plantas industriales y estructuras, atestados de accidentes y monitorización de movimientos del terreno y deformaciones de estructuras. En la auscultación de presas, comparado con la monitorización de puntos concretos dentro, en coronación o en el paramento de la presa, disponer de un modelo continuo del paramento aguas abajo de la presa abre la posibilidad de introducir los métodos de análisis de deformaciones de superficies y la creación de modelos de comportamiento que mejoren la comprensión y previsión de sus movimientos. No obstante, la aplicación de la tecnología TLS en la auscultación de presas debe considerarse como un método complementario a los existentes. Mientras que los péndulos y la reciente técnica basada en el sistema de posicionamiento global diferencial (DGPS) dan una información continua de los movimientos de determinados puntos de la presa, el TLS permite ver la evolución estacional y detectar posibles zonas problemáticas en todo el paramento. En este trabajo se analizan las características de la tecnología TLS y los parámetros que intervienen en la precisión final de los escaneos. Se constata la necesidad de utilizar equipos basados en la medida directa del tiempo de vuelo, también llamados pulsados, para distancias entre 100 m y 300 m Se estudia la aplicación del TLS a la modelización de estructuras y paramentos verticales. Se analizan los factores que influyen en la precisión final, como el registro de nubes, tipo de dianas y el efecto conjunto del ángulo y la distancia de escaneo. Finalmente, se hace una comparación de los movimientos dados por los péndulos directos de una presa con los obtenidos del análisis de las nubes de puntos correspondientes a varias campañas de escaneos de la misma presa. Se propone y valida el empleo de gráficos patrón para relacionar las variables precisión o exactitud con los factores distancia y ángulo de escaneo en el diseño de trabajos de campo. Se expone su aplicación en la preparación del trabajo de campo para la realización de una campaña de escaneos dirigida al control de movimientos de una presa y se realizan recomendaciones para la aplicación de la técnica TLS a grandes estructuras. Se ha elaborado el gráfico patrón de un equipo TLS concreto de alcance medio. Para ello se hicieron dos ensayos de campo en condiciones reales de trabajo, realizando escaneos en todo el rango de distancias y ángulos de escaneo del equipo. Se analizan dos métodos para obtener la precisión en la modelización de paramentos y la detección de movimientos de estos: el método del “plano de mejor ajuste” y el método de la “deformación simulada”. Por último, se presentan los resultados de la comparación de los movimientos estacionales de una presa arco-gravedad entre los registrados con los péndulos directos y los obtenidos a partir de los escaneos realizados con un TLS. Los resultados muestran diferencias de milímetros, siendo el mejor de ellos del orden de un milímetro. Se explica la metodología utilizada y se hacen consideraciones respecto a la densidad de puntos de las nubes y al tamaño de las mallas de triángulos. A shift of paradigm in the conception of the survey digital models is taking place in geodesy, moving from designing a model with the fewer possible number of points to models of hundreds of thousand or million points. This change has happened because of the introduction of new technologies like the laser scanner, the interferometry radar and the processing of images. The fast acceptance of these new technologies has been due mainly to the great speed getting the data, to the accessibility as reflectorless technique, and to the high degree of detail of the models. Classic survey methods are based on discreet measures of points that, considered them as a whole, form a model; the precision of the model is then derived from the precision measuring the single points. The terrestrial laser scanner (TLS) technology supposes a different approach to the model generation of the observed object. Point cloud, the result of a TLS scan, must be treated as a whole, by means of area-based analysis; so, the final model is not an aggregation of points but the one resulting from the best surface that fits with the point cloud. Comparing precisions between the one resulting from the capture of singular points made with tachometric measurement methods and with TLS equipment, the inferiority of this last one is clear; but it is in the treatment of the point clouds, using area-based analysis methods, when acceptable precisions have been obtained and it has been possible to consider the incorporation of this technology for monitoring structures deformations. Among TLS applications it have to be emphasized those of registry of the cultural heritage, stages registry during construction of industrial plants and structures, police statement of accidents and monitorization of land movements and structures deformations. Compared with the classical dam monitoring, approach based on the registry of a set of points, the fact having a continuous model of the downstream face allows the possibility of introducing deformation analysis methods and behavior models that would improve the understanding and forecast of dam movements. However, the application of TLS technology for dam monitoring must be considered like a complementary method with the existing ones. Pendulums and recently the differential global positioning system (DGPS) give a continuous information of the movements of certain points of the dam, whereas TLS allows following its seasonal evolution and to detect damaged zones of the dam. A review of the TLS technology characteristics and the factors affecting the final precision of the scanning data is done. It is stated the need of selecting TLS based on the direct time of flight method, also called pulsed, for scanning distances between 100m and 300m. Modelling of structures and vertical walls is studied. Factors that influence in the final precision, like the registry of point clouds, target types, and the combined effect of scanning distance and angle of incidence are analyzed. Finally, a comparison among the movements given by the direct pendulums of a dam and the ones obtained from the analysis of point clouds is done. A new approach to obtain a complete map-type plot of the precisions of TLS equipment based on the direct measurement of time of flight method at midrange distances is presented. Test were developed in field-like conditions, similar to dam monitoring and other civil engineering works. Taking advantage of graphic semiological techniques, a “distance - angle of incidence” map based was designed and evaluated for field-like conditions. A map-type plot was designed combining isolines with sized and grey scale points, proportional to the precision values they represent. Precisions under different field conditions were compared with specifications. For this purpose, point clouds were evaluated under two approaches: the standar "plane-of-best-fit" and the proposed "simulated deformation”, that showed improved performance. These results lead to a discussion and recommendations about optimal TLS operation in civil engineering works. Finally, results of the comparison of seasonal movements of an arc-gravity dam between the registered by the direct pendulums ant the obtained from the TLS scans, are shown. The results show differences of millimeters, being the best around one millimeter. The used methodology is explained and considerations with respect to the point cloud density and to the size of triangular meshes are done.

Optical sensing of the fatigue damage state of CFRP under realistic aeronautical load sequences

We present an optical sensing methodology to estimate the fatigue damage state of structures made of carbon fiber reinforced polymer (CFRP), by measuring variations on the surface roughness. Variable amplitude loads (VAL), which represent realistic loads during aeronautical missions of fighter aircraft (FALSTAFF) have been applied to coupons until failure. Stiffness degradation and surface roughness variations have been measured during the life of the coupons obtaining a Pearson correlation of 0.75 between both variables. The data were compared with a previous study for Constant Amplitude Load (CAL) obtaining similar results. Conclusions suggest that the surface roughness measured in strategic zones is a useful technique for structural health monitoring of CFRP structures, and that it is independent of the type of load applied. Surface roughness can be measured in the field by optical techniques such as speckle, confocal perfilometers and interferometry, among others.

Electro-optical characterization of IC compatible microcantilevers

The aim of this work is to simulate and optically characterize the piezoelectric performance of complementary metal oxide semiconductor (CMOS) compatible microcantilevers based on aluminium nitride (AlN) and manufactured at room temperature. This study should facilitate the integration of piezoelectric micro-electro-mechanical systems (MEMS) such as microcantilevers, in CMOS technology. Besides compatibility with standard integrated circuit manufacturing procedures, low temperature processing also translates into higher throughput and, as a consequence, lower manufacturing costs. Thus, the use of the piezoelectric properties of AlN manufactured by reactive sputtering at room temperature is an important step towards the integration of this type of devices within future CMOS technology standards. To assess the reliability of our fabrication process, we have manufactured arrays of free-standing microcantilever beams of variable dimension and studied their piezoelectric performance. The characterization of the first out-of-plane modes of AlN-actuated piezoelectric microcantilevers has been carried out using two optical techniques: laser Doppler vibrometry (LDV) and white light interferometry (WLI). In order to actuate the cantilevers, a periodic chirp signal in certain frequency ranges was applied between the device electrodes. The nature of the different vibration modes detected has been studied and compared with that obtained by a finite element model based simulation (COMSOL Multiphysics), showing flexural as well as torsional modes. The correspondence between theoretical and experimental data is reasonably good, probing the viability of this high throughput and CMOS compatible fabrication process. To complete the study, X-ray diffraction as well as d33 piezoelectric coefficient measurements were also carried out.