Evaluation of the influence of visual parameters on wave transmission velocity in sawn chestnut timber

Non-destructive, visual evaluation and mechanical testing techniques were used to assess the structural properties of 374 samples of chestnut (Castanea sativa). The principal components method was applied to establish and interpret correlations between variables obtained of modulus of elasticity, bending strength and density. The static modulus of elasticity presented higher correlation values than those obtained using non-destructive methods. Bending strength presented low correlations with the non-destructive parameters, but there was some relation to the different knot ratios defined. The relationship was stronger with the most widely used ratio, CKDR. No significant correlations were observed between any of the variables and density.

Influence of the molecular architecture on the secondary relaxations of Poly(styrene-co-methylmethacrylate) copolymers

The processes of adsorption of grafted copolymers onto negatively charged surfaces were studied using a dissipative quartz crystal microbalance (D-QCM) and ellipsometry. The control parameters in the study of the adsorption are the existence or absence on the molecular architecture of grafted polyethyleneglycol (PEG) chains with different lengths and the chemical nature of the main chain, poly(allylamine) (PAH) or poly(L-lysine) (PLL). It was found out that the adsorption kinetics of the polymers showed a complex behavior. The total adsorbed amount depends on the architecture of the polymer chains (length of the PEG chains), on the polymer concentration and on the chemical nature of the main chain. The comparison of the thicknesses of the adsorbed layers obtained from D-QCM and from ellipsometry allowed calculation of the water content of the layers that is intimately related to the grafting length. The analysis of D-QCM results also provides information about the shear modulus of the layers, whose values have been found to be typical of a rubber-like polymer system. It is shown that the adsorption of polymers with a charged backbone is not driven exclusively by the electrostatic interactions, but the entropic contributions as a result of the trapping of water in the layer structure are of fundamental importance.

Study of the Influence of Reference System in Surface Finishing Parameters Evaluation.

In the present paper the influence of the reference system with regard to the characterization of the surface finishing is analyzed. The effect of the reference system’s choice on the most representative surface finishing parameters (e.g. roughness average Ra and root mean square values Rq) is studied. The study can also be applied to their equivalent parameters in waviness and primary profiles. Based on ISO and ASME standards, three different types of regression lines (central, mean and orthogonal) are theoretically and experimentally analyzed, identifying the validity and applicability fields of each one depending on profile’s geometry. El presente trabajo realiza un estudio de la influencia que supone la elección del sistema de referencia en la determinación los valores de los parámetros más relevantes empleados en la caracterización del acabado superficial tales como la rugosidad media aritmética Ra o la rugosidad media cuadrática Rq y sus equivalentes en los perfiles de ondulación y completo. Partiendo de la definición establecida por las normas ISO y ASME, se analizan tres tipos de líneas de regresión cuadrática (línea central, línea media y línea ortogonal), delimitando los campos de validez y de aplicación de cada una de ellas en función de la geometría del perfil. Para ello se plantean diversos tipos de perfiles y se desarrolla un estudio teórico y experimental de los mismos.

Residual effect of organic zinc complexes in acid and calcareous soils on navy bean (phaseolus vulgaris l.) and flax (linum usitatissimum l.) crops under greenhouse conditions. Influence of the moisture conditions = Efecto residual de complejos orgánicos de zinc en suelos ácido y calizo en cultivos de judía (phaseolus vulgaris l.) y lino (linum usitatissimum l.) Realizados en condiciones de invernadero. Influencia de las diferentes condiciones de humedad

El Zn es un elemento esencial para el crecimiento saludable y reproducción de plantas, animales y humanos. La deficiencia de Zn es una de las carencias de micronutrientes más extendidas en muchos cultivos, afectando a grandes extensiones de suelos en diferentes áreas agrícolas. La biofortificación agronómica de diferentes cultivos, incrementando la concentración de micronutriente Zn en la planta, es un medio para evitar la deficiencia de Zn en animales y humanos. Tradicionalmente se han utilizado fertilizantes de Zn inorgánicos, como el ZnSO4, aunque en los últimos años se están utilizado complejos de Zn como fuentes de este micronutriente, obteniéndose altas concentraciones de Zn soluble y disponible en el suelo. Sin embargo, el envejecimiento de la fuente en el suelo puede causar cambios importantes en su disponibilidad para las plantas. Cuando se añaden al suelo fuentes de Zn inorgánicas, las formas de Zn más solubles pierden actividad y extractabilidad con el paso del tiempo, transformándose a formas más estables y menos biodisponibles. En esta tesis se estudia el efecto residual de diferentes complejos de Zn de origen natural y sintético, aplicados en cultivos previos de judía y lino, bajo dos condiciones de riego distintas (por encima y por debajo de la capacidad de campo, respectivamente) y en dos suelos diferentes (ácido y calizo). Los fertilizantes fueron aplicados al cultivo previo en tres dosis diferentes (0, 5 y 10 mg Zn kg-1 suelo). El Zn fácilmente lixiviable se estimó con la extracción con BaCl2 0,1M. Bajo condiciones de humedad por encima de la capacidad de campo se obtuvieron mayores porcentajes de Zn lixiviado en el suelo calizo que en el suelo ácido. En el caso del cultivo de judía realizado en condiciones de humedad por encima de la capacidad de campo se compararon las cantidades extraídas con el Zn lixiviado real. El análisis de correlación entre el Zn fácilmente lixiviable y el estimado sólo fue válido para complejos con alta movilidad y para cada suelo por separado. Bajo condiciones de humedad por debajo de la capacidad de campo, la concentración de Zn biodisponible fácilmente lixiviable presentó correlaciones positivas y altamente significativas con la concentración de Zn disponible en el suelo. El Zn disponible se estimó con varios métodos de extracción empleados habitualmente: DTPA-TEA, DTPA-AB, Mehlich-3 y LMWOAs. Estas concentraciones fueron mayores en el suelo ácido que en el calizo. Los diferentes métodos utilizados para estimar el Zn disponible presentaron correlaciones positivas y altamente significativas entre sí. La distribución del Zn en las distintas fracciones del suelo fue estimada con diferentes extracciones secuenciales. Las extracciones secuenciales mostraron un descenso entre los dos cultivos (el anterior y el actual) en la fracción de Zn más lábil y un aumento en la concentración de Zn asociado a fracciones menos lábiles, como carbonatos, óxidos y materia orgánica. Se obtuvieron correlaciones positivas y altamente significativas entre las concentraciones de Zn asociado a las fracciones más lábiles (WSEX y WS+EXC, experimento de la judía y lino, respectivamente) y las concentraciones de Zn disponible, estimadas por los diferentes métodos. Con respecto a la planta se determinaron el rendimiento en materia seca y la concentración de Zn en planta. Se observó un aumento del rendimiento y concentraciones con el efecto residual de la dosis mayores (10 mg Zn kg-1) con respecto a la dosis inferior (5 mg Zn 12 kg-1) y de ésta con respecto a la dosis 0 (control). El incremento de la concentración de Zn en todos los tratamientos fertilizantes, respecto al control, fue mayor en el suelo ácido que en el calizo. Las concentraciones de Zn en planta indicaron que, en el suelo calizo, serían convenientes nuevas aplicaciones de Zn en posteriores cultivos para mantener unas adecuadas concentraciones en planta. Las mayores concentraciones de Zn en la planta de judía, cultivada bajo condiciones de humedad por encima de la capacidad de campo, se obtuvieron en el suelo ácido con el efecto residual del Zn-HEDTA a la dosis de 10 mg Zn kg-1 (280,87 mg Zn kg-1) y en el suelo calizo con el efecto residual del Zn-DTPA-HEDTA-EDTA a la dosis de 10 mg Zn kg-1 (49,89 mg Zn kg-1). En el cultivo de lino, cultivado bajo condiciones de humedad por debajo de la capacidad de campo, las mayores concentraciones de Zn en planta ese obtuvieron con el efecto residual del Zn-AML a la dosis de 10 mg Zn kg-1 (224,75 mg Zn kg-1) y en el suelo calizo con el efecto residual del Zn-EDTA a la dosis de 10 mg Zn kg-1 (99,83 mg Zn kg-1). El Zn tomado por la planta fue determinado como combinación del rendimiento y de la concentración en planta. Bajo condiciones de humedad por encima de capacidad de campo, con lixiviación, el Zn tomado por la judía disminuyó en el cultivo actual con respecto al cultivo anterior. Sin embargo, en el cultivo de lino, bajo condiciones de humedad por debajo de la capacidad de campo, se obtuvieron cantidades de Zn tomado superiores en el cultivo actual con respecto al anterior. Esta tendencia también se observó, en ambos casos, con el porcentaje de Zn usado por la planta. Summary Zinc is essential for healthy growth and reproduction of plants, animals and humans. Zinc deficiency is one of the most widespread micronutrient deficiency in different crops, and affect different agricultural areas. Agronomic biofortification of crops produced by an increased of Zn in plant, is one way to avoid Zn deficiency in animals and humans Sources with inorganic Zn, such as ZnSO4, have been used traditionally. Although, in recent years, Zn complexes are used as sources of this micronutrient, the provide high concentrations of soluble and available Zn in soil. However, the aging of the source in the soil could cause significant changes in their availability to plants. When an inorganic source of Zn is added to soil, Zn forms more soluble and extractability lose activity over time, transforming into forms more stable and less bioavailable. This study examines the residual effect of different natural and synthetic Zn complexes on navy bean and flax crops, under two different moisture conditions (above and below field capacity, respectively) and in two different soils (acid and calcareous). Fertilizers were applied to the previous crop in three different doses (0, 5 y 10 mg Zn kg-1 soil). The easily leachable Zn was estimated by extraction with 0.1 M BaCl2. Under conditions of moisture above field capacity, the percentage of leachable Zn in the calcareous soil was higher than in acid soil. In the case of navy bean experiment, performed in moisture conditions of above field capacity, amounts extracted of easily leachable Zn were compared with the real leachable Zn. Correlation analysis between the leachable Zn and the estimate was only valid for complex with high mobility and for each soil separately. Under moisture conditions below field capacity, the concentration of bioavailable easily leachable Zn showed highly significant positive correlations with the concentration of available soil Zn. The available Zn was estimated with several commonly used extraction methods: DTPA-TEA, AB-DTPA, Mehlich-3 and LMWOAs. These concentrations were higher in acidic soil than in the calcareous. The different methods used to estimate the available Zn showed highly significant positive correlations with each other. The distribution of Zn in the different fractions of soil was estimated with different sequential extractions. The sequential extractions showed a decrease between the two crops (the previous and current) at the most labile Zn fraction and an increase in the concentration of Zn associated with the less labile fractions, such as carbonates, oxides and organic matter. A positive and highly significant correlation was obtained between the concentrations of Zn associated with more labile fractions (WSEX and WS + EXC, navy bean and flax experiments, respectively) and available Zn concentrations determined by the different methods. Dry matter yield and Zn concentration in plants were determined in plant. Yield and Zn concentration in plant were higher with the residual concentrations of the higher dose applied (10 mg Zn kg-1) than with the lower dose (5 mg Zn kg-1), also these parameters showed higher values with application of this dose than with not Zn application. The increase of Zn concentration in plant with Zn treatments, respect to the control, was greater in the acid soil than in the calcareous. The Zn concentrations in plant indicated that in the calcareous soil, new applications of Zn are desirable in subsequent crops to maintain suitable concentrations in plant. 15 The highest concentrations of Zn in navy bean plant, performed under moisture conditions above the field capacity, were obtained with the residual effect of Zn-HEDTA at the dose of 10 mg Zn kg-1 (280.87 mg Zn kg-1) in the acid soil, and with the residual effect of Zn- DTPA-HEDTA-EDTA at a dose of 10 mg Zn kg-1 (49.89 mg Zn kg-1) in the calcareous soil. In the flax crop, performed under moisture conditions below field capacity, the highest Zn concentrations in plant were obtained with the residual effect of Zn-AML at the dose of 10 mg Zn kg-1 (224.75 Zn mg kg-1) and with the residual effect of Zn-EDTA at a dose of 10 mg Zn kg-1 (99.83 mg Zn kg-1) in the calcareous soil. The Zn uptake was determined as a combination of yield and Zn concentration in plant. Under moisture conditions above field capacity, with leaching, Zn uptake by navy bean decreased in the current crop, respect to the previous crop. However, in the flax crop, under moisture conditions below field capacity, Zn uptake was higher in the current crop than in the previous. This trend is also observed in both cases, with the percentage of Zn used by the plant

Influence of the application of Jasmonic Acid and Benzoic Acid on Watermelon fruit quality.

In watermelon crops in Southeastern Spain, important thermal differences appear during the first stages of plant development that can affect them. This work shows the effect of applying jasmonic acid and benzoic acid (JA+BA), inductors of systemic acquired resistance (SAR) and induced systemic resistance (ISR), respectively, on fruit quality parameters from a crop in a greenhouse in Southeastern Spain, where crops face a remarkable abiotic stress. We assessed two treatments of JA+BA, T1 (500+500 ppm), T2 (2000+2000 ppm) and a control test using an experimental design of randomized blocks with four replications. The results obtained for the parameters assessed (ºBrix, flesh firmness, rind thickness, polar and equatorial diameter) did not show statistically significant differences. The results showed that there was no metabolic cost in the plants when applying the assessed treatments of JA+BA.

The influence of diet on the effectiveness of garlic oil and cinnamaldehyde to manipulate in vitro ruminal fermentation and methane production.

The objective of this study was to evaluate the effects of increasing doses [0 (control: CON), 20, 60, 180 and 540 mg/L incubation medium] of garlic oil (GO) and cinnamaldehyde (CIN) on in vitro ruminal fermentation of two diets. Batch cultures of mixed ruminal microorganisms were inoculated with ruminal fluid from four sheep fed a medium-concentrate diet (MC; 50 : 50 alfalfa hay : concentrate) or four sheep fed a high-concentrate diet (HC; 15 : 85 barley straw : concentrate). Diets MC and HC were representative of those fed to dairy and fattening ruminants, respectively. Samples of each diet were used as incubation substrates for the corresponding inoculum, and the incubation was repeated on 4 different days (four replicates per experimental treatment). There were GO × diet-type and CIN × diet-type interactions (P < 0.001–0.05) for many of the parameters determined, indicating different effects of both oils depending on the diet type. In general, effects of GO were more pronounced for MC compared with HC diet. Supplementation of GO did not affect (P > 0.05) total volatile fatty acid (VFA) production at any dose. For MC diet, GO at 60, 180 and 540 mg/L decreased (P < 0.05) molar proportion of acetate (608, 569 and 547 mmol/mol total VFA, respectively), and increased (P < 0.05) propionate proportion (233, 256 and 268 mmol/mol total VFA, respectively), compared with CON values (629 and 215 mmol/mol total VFA for acetate and propionate, respectively). A minimum dose of 180 mg of GO/L was required to produce similar modifications in acetate and propionate proportions with HC diet, but no effects (P > 0.05) on butyrate proportion were detected. Methane/VFA ratio was reduced (P < 0.05) by GO at 60, 180 and 540 mg/L for MC diet (0.23, 0.16 and 0.10 mol/mol, respectively), and by GO at 20, 60, 180 and 540 mg/L for HC diet (0.19, 0.19, 0.16 and 0.08 mol/mol, respectively), compared with CON (0.26 and 0.21 mol/mol for MC and HC diets, respectively). No effects (P = 0.16–0.85) of GO on final pH and concentrations of NH3-N and lactate were detected. For both diet types, the highest CIN dose decreased (P < 0.05) production of total VFA, gas and methane, which would indicate an inhibition of fermentation. Compared with CON, CIN at 180 mg/L increased (P < 0.05) acetate proportion for the MC (629 and 644 mmol/mol total VFA for CON and CIN, respectively) and HC (525 and 540 mmol/mol total VFA, respectively) diets, without affecting the proportions of any other VFA or total VFA production. Whereas for MC diet CIN at 60 and 180 mg/L decreased (P < 0.05) NH3-N concentrations compared with CON, only a trend (P < 0.10) was observed for CIN at 180 mg/L with the HC diet. Supplementation of CIN up to 180 mg/L did not affect (P = 0.18–0.99) lactate concentrations and production of gas and methane for any diet. The results show that effectiveness of GO and CIN to modify ruminal fermentation may depend on diet type, which would have practical implications if they are confirmed in vivo.

Influence of new integrated pest management strategies on aphidophagous predators in horticultural crops

El 1 de enero de 2014 entró en vigor la Directiva Europea 2009/128/CE sobre uso sostenible de plaguicidas y el Real Decreto 1311/2012 por el cual se traspone dicha normativa comunitaria al ámbito nacional. Estos reglamentos establecen el marco legal por el que las explotaciones agrícolas deben cumplir los principios generales de la Gestión Integrada de Plagas (GIP). Los principios de la GIP dan preferencia a aquellos métodos de control que sean sostenibles y respetuosos con el medio ambiente, dando prioridad al control biológico, al físico y a otros de carácter no químico. Sin embargo, el uso de insecticidas selectivos con los enemigos naturales es necesario en ocasiones para el adecuado manejo de las plagas en cultivos hortícolas. Por ello, el objetivo general de esta Tesis ha sido aportar conocimientos para la mejora del control de plagas en cultivos hortícolas, mediante la integración de estrategias de lucha biológica, física y química. La primera de las líneas de investigación de esta Tesis se centró en el estudio del efecto de la presencia dos depredadores, larvas Chrysoperla carnea y adultos de Adalia bipunctata, en la dispersión del virus de transmisión no persistente Cucumber mosaic virus (CMV) y del virus de transmisión persistente Cucurbit aphid-borne yellows virus (CABYV), transmitidos por el pulgón Aphis gosypii en cultivo de pepino. La tasa de transmisión de CMV fue baja para los dos tiempos de evaluación ensayados (1 y 5 días), debido al limitado movimiento de su vector A. gossypii. Las plantas que resultaron infectadas se localizaron próximas a la fuente de inóculo central y la presencia de ambos enemigos naturales no incrementó significativamente el porcentaje de plantas ocupadas por pulgones ni la tasa de transmisión de CMV. Los patrones de distribución de A. gossypii y de CMV tan solo fueron coincidentes en las proximidades de la planta central infectada en la que se liberaron los insectos. En los ensayos con CABYV, la presencia de C. carnea y de A. bipunctata respectivamente provocó un incremento significativo de la dispersión de A. gossypii tras 14 días, pero no tras 7 días desde la liberación de los insectos. La reducción en el número inicial de pulgones en la planta central infectada con CABYV fue siempre mayor tras la liberación de C. carnea en comparación con A. bipunctata. Sin embargo, la tasa de transmisión de CABYV y su distribución espacial no se vieron significativamente modificadas por la presencia de ninguno de los depredadores, ni tras 7 días ni tras 14 días desde el inicio de los ensayos. Al igual que se estudió el efecto de la presencia de enemigos naturales en el comportamiento de las plagas y en la epidemiología de las virosis que transmiten, en una segunda línea de investigación se evaluó el posible efecto del consumo de pulgones portadores de virus por parte de los enemigos naturales. Este trabajo se llevó a cabo en el Laboratorio de Ecotoxicología del Departamento de Entomología de la Universidade Federal de Lavras (UFLA) (Brasil). En él se evaluó la influencia en los parámetros biológicos del enemigo natural Chrysoperla externa al alimentarse de Myzus persicae contaminados con el virus de transmisión persistente Potato leafroll virus (PLRV). El consumo de M. persicae contaminados con PLRV incrementó significativamente la duración de la fase larvaria, reduciendo también la supervivencia en comparación a otras dos dietas a base de M. persicae no contaminados con el virus y huevos del lepidóptero Ephestia kuehniella. La duración de la fase de pupa de C. externa no difirió significativamente entre las dietas a base de pulgones contaminados con PLRV y pulgones no contaminados, pero ambas fueron menores que con la dieta con huevos de E. kuehniella. Sin embargo, ni la supervivencia en la fase de pupa ni los parámetros reproductivos de los adultos emergidos mostraron diferencias significativas entre las dietas evaluadas. Por el contrario, la supervivencia de los adultos durante los 30 primeros días desde su emergencia sí se vio significativamente afectada por la dieta, siendo al término de este periodo del 54% para aquellos adultos de C. externa que durante su fase larvaria consumieron pulgones con PLRV. Dentro de la GIP, una de las estrategias de carácter físico que se emplean para el control de plagas y enfermedades en cultivos hortícolas protegidos es el uso de plásticos con propiedades fotoselectivas de absorción de la radiación ultravioleta (UV). Por ello, la tercera línea de investigación de la Tesis se centró en el estudio de los efectos directos e indirectos (mediados por la planta) de condiciones especiales de baja radiación UV sobre el crecimiento poblacional del pulgón A. gossypii y los parámetros biológicos del enemigo natural C. carnea, así como sobre las plantas de pepino en las que se liberaron los insectos. Los ensayos se realizaron en jaulones dentro de invernadero, utilizándose en el primero de ellos plantas de pepino sanas, mientras que en el segundo las plantas de pepino fueron previamente infectadas con CABYV para estudiar de qué manera afectaba la incidencia del virus en las mismas condiciones. Las condiciones de baja radiación UV (bajo plástico Térmico Antivirus®) ejercieron un efecto directo en las fases iniciales del cultivo de pepino, promoviendo su crecimiento, mientras que en fases más avanzadas del cultivo indujeron un aumento en el contenido en nitrógeno de las plantas. Las plantas de pepino que fueron sometidas a mayor intensidad de radiación UV (bajo plástico Térmico Blanco®) al inicio del cultivo mostraron un engrosamiento significativo de las paredes de las células epidérmicas del haz de las hojas, así como de la cutícula. El uso del plástico Térmico Antivirus®, utilizado como barrera fotoselectiva para crear condiciones de baja radiación UV, no alteró con respecto al plástico Térmico Blanco® (utilizado como control) el desarrollo poblacional del pulgón A. gossypii ni los parámetros biológicos evaluados en el depredador C. carnea. En el segundo experimento, realizado con plantas infectadas con CABYV, la incidencia de la virosis enmascaró las diferencias encontradas en experimento con plantas sanas, reduciendo aparentemente la influencia de las distintas condiciones de radiación UV. Por último, para el desarrollo de las estrategias de GIP es importante estudiar los posibles efectos secundarios que los plaguicidas pueden tener en los enemigos naturales de las plagas. Es por ello que en la Tesis se evaluaron la toxicidad y los efectos subletales (fecundidad y fertilidad) de flonicamida, flubendiamida, metaflumizona, spirotetramat, sulfoxaflor y deltametrina en los enemigos naturales C. carnea y A. bipunctata. Los efectos secundarios fueron evaluados por contacto residual tanto para larvas como para adultos de ambos enemigos naturales en condiciones de laboratorio. Flonicamida, flubendiamida, metaflumizona y spirotetramat fueron inocuos para larvas de último estadio y adultos de C. carnea y A. bipunctata. Por este motivo, estos insecticidas se presentan como buenos candidatos para ser incorporados dentro de programas de GIP en combinación con estos enemigos naturales para el control de plagas de cultivos hortícolas. Sulfoxaflor fue ligeramente tóxico para adultos de C. carnea y altamente tóxico para larvas de último estadio de A. bipunctata. Para A. bipunctata, sulfoxaflor y deltametrina fueron los compuestos más dañinos. Deltametrina fue también el compuesto más tóxico para larvas y adultos de C. carnea. Por tanto, el uso de deltametrina y sulfoxaflor en programas de GIP debería tomarse en consideración cuando se liberasen cualquiera de estos dos enemigos naturales debido al comportamiento tóxico que mostraron en condiciones de laboratorio. ABSTRACT On 1 January 2014 came into effect the Directive 2009/128/EC of the European Parliament about sustainable use of pesticides and the Royal Decree 1311/2012 that transposes the regulation to the Spanish level. These regulations establish the legal framework that agricultural holdings must adhere to in order to accomplish the general principles of Integrated Pest Management (IPM). The guidelines of IPM give priority to sustainable and eco-friendly pest control techniques, such as biological and physical measures. Nevertheless, the use of pesticides that are selective to natural enemies is sometimes a necessary strategy to implement accurate pest management programs in horticultural protected crops. Therefore, the general objective of this Thesis was to contribute to the improvement of pest management strategies in horticultural crops, by means of the integration of biological, physical and chemical techniques. The first research line of this Thesis was focused on the evaluation of the effects of two aphidophagous predators, Chrysoperla carnea larvae and Adalia bipunctata adults, on the spread of the non-persistently transmitted Cucumber mosaic virus (CMV, Cucumovirus) and the persistently transmitted Cucurbit aphid-borne yellows virus (CABYV, Polerovirus), by the aphid vector Aphis gossypii in a cucumber crop under greenhouse conditions. The CMV transmission rate was generally low, both after 1 and 5 days, due to the limited movement of its aphid vector A. gossypii. Infected plants were mainly located around the central virusinfected source plant, and the percentage of aphid occupation and CMV-infected plants did not differ significantly in absence and presence of natural enemies. The distribution patterns of A. gossypii and CMV were only coincident close to the central plant where insects were released. In the CABYV experiments, the presence of C. carnea larvae and A. bipunctata adults induced significant A. gossypii dispersal after 14 days but not after 7 days. The reduction in the initial aphid population established in the central plant was always higher for C. carnea than for A. bipunctata. Nevertheless, CABYV spread was not significantly modified by the presence of each predator either in the short term (7 days) or in the long term (14 days). Furthermore, the percentage of CABYV-infected plants did not significantly differ when each natural enemy was present in any evaluation period. It is important to evaluate the influence that natural enemies have on pest dynamics and on the spread of viral diseases, but it should be also taken into account the possible effect on the performance of natural enemies when they feed on preys that act as vectors of viruses. Thus, in a second research line developed in the Laboratory of Ecotoxicology, Department of Entomology, of the Universidade Federal de Lavras (UFLA) (Brazil), it was evaluated the performance of Chrysoperla externa under the condition of consuming Myzus persicae acting as vector of Potato leafroll virus (PLRV). The diet composed of PLRV-infected M. persicae significantly increased the length and reduced the survival rate, of the larval period in regard to the other two diets, composed of non-infected M. persicae and Ephestia kuehniella eggs. The lengths of the pupal stage were not significantly different between the aphid diets, but both were significantly shorter than that of E. kuehniella eggs. Neither pupal survival nor reproductive parameters revealed significant differences among the diets. Nevertheless, the adult survival curves during the first 30 days after emergence showed significant differences, reaching at the end of this interval a value of 54% for those C. externa adults fed on PLRVinfected aphids during their larval period. According to the IPM guidelines, one of the physical strategies for the control of pests and diseases in horticultural protected crops is the use of plastic films with photoselective properties that act as ultraviolet (UV) radiation blocking barriers. In this sense, the third research line of the Thesis dealt with the study of the direct and plant-mediated influence of low UV radiation conditions on the performance of the aphid A. gossypii and on the biological parameters of the natural enemy C. carnea, as well as on the cucumber plants where insects were released. The experiments were conducted inside cages under greenhouse conditions, using for the first one healthy cucumber plants, while for the second experiment the cucumber plants were previously infected with CABYV in order to assess the influence of the virus in the same conditions. The low UV radiation conditions (under Térmico Antivirus® plastic film) seemed to exert a direct effect in the early stages of cucumber plants, enhancing their growth, and in an increasing nitrogen content at further developmental stages. The higher UV radiation exposure (under Térmico Blanco® plastic film) in the early stages of the cucumber crop induced the thickening of the adaxial epidermal cell walls and the cuticle of leaves. The use of Térmico Antivirus® plastic film as a photoselective barrier to induce low UV radiation conditions did not modify, in regard to Térmico Blanco® plastic film (used as control), neither the population development of A. gossypii nor the studied biological parameters of the predator C. carnea. In the second experiment, done with CABYV-infected cucumber plants, the incidence of the virus seemed to mask the direct and plant-mediated influence of the different UV radiation conditions. In last term, for the development of IPM strategies it is important to study the potential side effects that pesticides might have on natural enemies. For this reason, in the Thesis were tested the toxicity and sublethal effects (fecundity and fertility) of flonicamid, flubendiamide, metaflumizone, spirotetramat, sulfoxaflor and deltamethrin on the natural enemies C. carnea and A. bipunctata. The side effects of the active ingredients of the insecticides were evaluated with residual contact tests for the larvae and adults of these predators under laboratory conditions. Flonicamid, flubendiamide, metaflumizone and spirotetramat were innocuous to last instar larvae and adults of C. carnea and A. bipunctata. Therefore, these pesticides are promising candidates for being incorporated into IPM programs in combination with these natural enemies for the control of particular greenhouse pests. In contrast, sulfoxaflor was slightly toxic to adults of C. carnea and was highly toxic to last instar larvae of A. bipunctata. For A. bipunctata, sulfoxaflor and deltamethrin were the most damaging compounds. Deltamethrin was also the most toxic compound to larvae and adults of C. carnea. In accordance with this fact, the use of sulfoxaflor and deltamethrin in IPM strategies should be taken into consideration when releasing either of these biological control agents, due to the toxic behavior observed under laboratory conditions.

Evaluation of the influence of toll systems on energy consumption and CO2 emissions: A case study of a Spanish highway

This paper studies the energy consumption and subsequent CO2 emissions of road highway transportation under three toll systems in Spain for four categories of vehicles: cars, vans, buses and articulated trucks. The influence of toll systems is tested for a section of AP-41 highway between Toledo and Madrid. One system is free flow, other is traditional stop and go and the last toll system operates with an electronic toll collection (ETC) technology. Energy consumption and CO2 emissions were found to be closely related to vehicle mass, wind exposure, engine efficiency and acceleration rate. These parameters affect, directly or indirectly, the external forces which determine the energy consumption. Reducing the magnitude of these forces through an appropriate toll management is an important way of improving the energy performance of vehicles. The type of toll system used can have a major influence on the energy efficiency of highway transportation and therefore it is necessary to consider free flow.

Influence of coiling on the stress relaxation of prestressing steel wires

The possible deleterious effects of coiling and long time storage of coiled wires on the stress relaxation behaviour of prestressing steel wires has been checked by means of experimental work and a simple analytical model. The results show that if the requirements of Standards are fulfilled (minimum coiling diameters) these effects can be neglected. However, some other factors like previous residual stresses, long time storage or storage at high temperatures, can trigger or emphasize this damage on the material. In the authors? opinion it is recommended to control the final curvature of the wires after uncoiling prior to prestressin, as required in some Standards.

Influence of Current Pulse Shape on Directly Modulated Systems Performance in Metro Area Optical Networks

Due to the fact that a metro network market is very cost sensitive, direct modulated schemes appear attractive. In this paper a CWDM (Coarse Wavelength Division Multiplexing) system is studied in detail by means of an Optical Communication System Design Software; a detailed study of the modulated current shape (exponential, sine and gaussian) for 2.5 Gb/s CWDM Metropolitan Area Networks is performed to evaluate its tolerance to linear impairments such as signal-to-noise-ratio degradation and dispersion. Point-to-point links are investigated and optimum design parameters are obtained. Through extensive sets of simulation results, it is shown that some of these shape pulses are more tolerant to dispersion when compared with conventional gaussian shape pulses. In order to achieve a low Bit Error Rate (BER), different types of optical transmitters are considered including strongly adiabatic and transient chirp dominated Directly Modulated Lasers (DMLs). We have used fibers with different dispersion characteristics, showing that the system performance depends, strongly, on the chosen DML?fiber couple.

Influence of coiling in stress relaxation of prestressing steel wires

The possible deleterious effects of coiling and long-time storage of coiled wires on the stress relaxation behaviour of prestressing steel wires has been checked by means of experimental work and a simple analytical model. The results show that if the requirements of Standards are fulfilled (minimum coiling diameters) these effects can be neglected. However, some other factors like previous residual stresses, long-time storage or storage at high temperatures, can trigger or emphasise this damage to the material. In the authors’ opinion it is recommendable to control the final curvature of the wires after uncoiling prior to prestressing, as required in some Standards.

Influence of cement properties in the reaction rate and mechanical behavior of concrete with high fl y ash content

The use of fly ash (FA) as an admixture to concrete is broadly extended for two main reasons: the reduction of costs that supposes the substitution of cement and the micro structural changes motivated by the mineral admixture. Regarding this second point, there is a consensus that considers that the ash generates a more compact concrete and a reduction in the size of the pore. However, the measure in which this contributes to the pozzolanic activity or as filler is not well defined. There is also no justification to the influence of the physical parameters, fineness of the grain and free water, in its behavior. This work studies the use of FA as a partial substitute of the cement in concretes of different workability (dry and wet) and the influence in the reactivity of the ash. The concrete of dry consistency which serves as reference uses a cement dose of 250 Kg/m 3 and the concrete of fluid consistency utilized a dose of cement of 350 Kg/m 3 . Two trademark of Portland Cement Type 1 were used. The first reached the resistant class for its fineness of grain and the second one for its composition. Moreover, three doses of FA have been used, and the water/binder ratio was constant in all the mixtures. We have studied the mechanical properties and the micro-structure of the concretes by means of compressive strength tests, mercury intrusion porosimetry (MIP) and thermal analysis (TA). The results of compressive strength tests allow us to observe that concrete mixtures with cements of the same classification and similar dosage of binder do not present the same mechanical behavior. These results show that the effective water/binder ratio has a major role in the development of the mechanical properties of concrete. The study of different dosages using TA, thermo-gravimetry and differential thermal analysis, revealed that the portlandite content is not restrictive in any of the dosages studied. Again, this proves that the rheology of the material influences the reaction rate and content of hydrated cement products. We conclude that the available free water is determinant in the efficiency of pozzolanic reaction. It is so that in accordance to the availability of free water, the ashes can react as an active admixture or simply change the porous distribution. The MIP shows concretes that do not exhibit significant changes in their mechanical behavior, but have suffered significant variation in their porous structure

Influence of laser wavelength on Laser-Fired contacts for crystalline silicon solar cells

In the Laser-Fired Contact (LFC) process, a laser beam fires a metallic layer through a dielectric passivating layer into the silicon wafer to form an electrical contact with the silicon bulk [1]. This laser technique is an interesting alternative for the fabrication of both laboratory and industrial scale high efficiency passivated emitter and rear cell (PERC). One of the principal characteristics of this promising technique is the capability to reduce the recombination losses at the rear surface in crystalline silicon solar cells. Therefore, it is crucial to optimize LFC because this process is one of the most promising concepts to produce rear side point contacts at process speeds compatible with the final industrial application. In that sense, this work investigates the optimization of LFC processing to improve the back contact in silicon solar cells using fully commercial solid state lasers with pulse width in the ns range, thus studying the influence of the wavelength using the three first harmonics (corresponding to wavelengths of 1064 nm, 532 nm and 355 nm). Previous studies of our group focused their attention in other processing parameters as laser fluence, number of pulses, passivating material [2, 3] thickness of the rear metallic contact [4], etc. In addition, the present work completes the parametric optimization by assessing the influence of the laser wavelength on the contact property. In particular we report results on the morphology and electrical behaviour of samples specifically designed to assess the quality of the process. In order to study the influence of the laser wavelength on the contact feature we used as figure of merit the specific contact resistance. In all processes the best results have been obtained using green (532 nm) and UV (355 nm), with excellent values for this magnitude far below 1 mΩcm2.

Influence of loudspeaker directivity on the measurement uncertainty of the acoustic testing of facades.

One of the most significant aspects of a building?s acoustic behavior is the airborne sound insulation of the room façades, since this determines the protection of its inhabitants against environmental noise. For this reason, authorities in most countries have established in their acoustic regulations for buildings the minimum value of sound insulation that must be respected for façades. In order to verify compliance with legal requirements it is usual to perform acoustic measurements in the finished buildings and then compare the measurement results with the established limits. Since there is always a certain measurement uncertainty, this uncertainty must be calculated and taken into account in order to ensure compliance with specifications. The most commonly used method for measuring sound insulation on façades is the so-called Global Loudspeaker Method, specified in ISO 140-5:1998. This method uses a loudspeaker placed outside the building as a sound source. The loudspeaker directivity has a significant influence on the measurement results, and these results may change noticeably by choosing different loudspeakers, even though they all fulfill the directivity requirements of ISO 140-5. This work analyzes the influence of the loudspeaker directivity on the results of façade sound insulation measurement, and determines its contribution to measurement uncertainty. The theoretical analysis is experimentally validated by means of an intermediate precision test according to ISO 5725-3:1994, which compares the values of sound insulation obtained for a façade using various loudspeakers with different directivities. Keywords: Uncertainty, Façade, Insulation

Influence of the Second Flexural Mode on the Response of High-Speed Bridges

This paper deals with the assessment of the contribution of the second flexural mode to the dynamic behaviour of simply supported railway bridges. Alluding to the works of other authors, it is suggested in some references that the dynamic behaviour of simply supported bridges could be adequately represented taking into account only the contribution of the fundamental flexural mode. On the other hand, the European Rail Research Institute (ERRI) proposes that the second mode should also be included whenever the associated natural frequency is lower than 30 Hz]. This investigation endeavours to clarify the question as much as possible by establishing whether the maximum response of the bridge, in terms of displacements, accelerations and bending moments, can be computed accurately not taking account of the contribution of the second mode. To this end, a dimensionless formulation of the equations of motion of a simply supported beam traversed by a series of equally spaced moving loads is presented. This formulation brings to light the fundamental parameters governing the behaviour of the beam: damping ratio, dimensionless speed $ \alpha$=VT/L, and L/d ratio (L stands for the span of the beam, V for the speed of the train, T represents the fundamental period of the bridge and d symbolises the distance between consecutive loads). Assuming a damping ratio equal to 1%, which is a usual value for prestressed high-speed bridges, a parametric analysis is conducted over realistic ranges of values of $ \alpha$ and L/d. The results can be extended to any simply supported bridge subjected to a train of equally spaced loads in virtue of the so-called Similarity Formulae. The validity of these formulae can be derived from the dimensionless formulation mentioned above. In the parametric analysis the maximum response of the bridge is obtained for one thousand values of speed that cover the range from the fourth resonance of the first mode to the first resonance of the second mode. The response at twenty-one different locations along the span of the beam is compared in order to decide if the maximum can be accurately computed with the sole contribution of the fundamental mode.