La rehabilitación de construcciones militares para uso hotelero: la red de Paradores de Turismo, (1928-2012)

Fundamento de la tesis: Al comienzo del siglo XX, el interés por el turismo unido a la necesidad de restaurar un abundante patrimonio histórico, posibilitó en España que los poderes públicos se embarcaran en una singular experiencia: la creación de una infraestructura hotelera a partir de la rehabilitación de edificios históricos. La preservación, mantenimiento e incluso rentabilidad de una gran parte del patrimonio español se haría efectiva a través de la innovadora fórmula patrimonio‐turismo, cuya máxima expresión se materializó en la Red de Paradores desde su fundación en la segunda década del siglo pasado hasta nuestros días. Sorprendentemente, este tema no ha sido todavía investigado en su vertiente arquitectónica pese a que España ha sido pionera y modelo en la cuestión de la hotelería pública. Este trabajo aborda el estudio del caso más significativo de todos los edificios de la red, en tanto que el patrimonio que ha servido de base a los fines hoteleros del Estado ha contado con un total de seis tipos arquitectónicos a lo largo de su historia, dentro de los cuales la arquitectura militar despunta con su mayoritaria presencia dentro del contexto de los edificios históricos de la red. El carácter arquetípico de los castillos y fortalezas, arraigado en el inconsciente colectivo, les hizo especialmente atractivos como alojamiento turístico al permitir evocar la remota época medieval, pese a ser el tipo arquitectónico más comprometido para la rehabilitación hotelera. El estudio de las intervenciones operadas en estos inmuebles se revela de forma clara como escaparate de los distintos criterios de intervención patrimonial que se han sucedido en el siglo XX, hasta enlazar con la perspectiva interdisciplinar actual. La tesis abarca en, primer lugar, diferentes aspectos generales relativos al promotor hotelero, la hotelería pública de ámbito nacional e internacional, y la caracterización de los inmuebles de la red estatal española, desde el punto de vista hotelero y arquitectónico, entendida esta última en sus tres escalas de influencia: la arquitectónica, la urbana o paisajística, y la del interiorismo. Se analiza en segundo término la arquitectura militar dentro del contexto de la Red de Paradores, desde la consideración de su transformación hotelera, para lo cual ha sido necesario realizar una clasificación propia, que abarca tanto edificios que respondieron a una estructura de cuartel, como castillos‐palacio, o fortalezas que habían servido a los fines de una orden religiosa militar, además de considerarse las intervenciones en recintos históricos de carácter militar, donde se hacía obligatorio construir de nueva planta. En tercer y último lugar, se analiza a lo largo de las distintas etapas del organismo turístico las rehabilitaciones realizadas en estas construcciones militares, a la vez que se tienen en cuenta las intervenciones en los restantes edificios históricos, para evitar la descontextualización. Este recorrido comienza con la promoción de los dos primeros paradores a cargo del Comisario Regio, el marqués de la Vega‐Inclán, que sirvieron para sentar las bases de los conceptos e ideas que habrían de desarrollarse en las siguientes décadas. Posteriormente, se desarrolló y tomó forma la red con el Patronato Nacional del Turismo, en la que las primeras intervenciones en tipos militares se tradujeron en reformas interiores de locales. La etapa clave de la red, y en particular de la arquitectura militar, tuvo lugar con el Ministerio de Información y Turismo, marcada por la “repristinación” de monumentos, tras un período preparatorio con la Dirección General del Turismo en el que lo militar había quedado de telón de fondo de otros tipos arquitectónicos. Tras el auge del Ministerio llegó el período de decadencia en el que los castillos y fortalezas desaparecieron de los intereses de las Secretarias de Turismo, hasta llegar a las inauguraciones de los novedosos establecimientos del siglo XXI y el resurgimiento del tipo militar con el parador de Lorca. Metodología empleada: Este trabajo de investigación se ha servido fundamentalmente de documentación inédita, procedente de diversos archivos, además de una muy extensa toma de datos in situ. Dentro del patrimonio analizado, los inmuebles que responden al tipo arquitectónico militar se han dividido en tres grandes grupos: inmuebles rehabilitados que entraron en funcionamiento en la red, inmuebles en proceso de transformación hotelera, e inmuebles que fueron adquiridos con fines hoteleros pero que no llegaron a rehabilitarse. Para cada uno de ellos ha sido necesario determinar en qué estado llegaron a manos de la Administración Turística, cuál fue el mecanismo a través del cual se adquirieron, en qué consistió su primera rehabilitación hotelera, y cuáles fueron las ampliaciones o reformas más significativas que se realizaron posteriormente. Estos datos se han sintetizado en fichas y se han extraído conclusiones al comparar cada unidad con el conjunto. Simultáneamente se introdujeron dos factores externos: la historia del turismo que permitió hacer una ordenación cronológica de los inmuebles según etapas, y la historia de la teoría y práctica de la intervención patrimonial en España que permitió comparar los criterios patrimoniales de la Administración competente respecto de las intervenciones de la Administración Turística, cuyo contacto se haría obligatorio a partir del Decreto, de 22 de abril de 1949, que dejaba bajo la tutela del Estado a todos los castillos y fortalezas. Aportación de la tesis: Con carácter general, la tesis centra una ordenación y sistematización completa del patrimonio inmobiliario de la red, desde el punto de vista de los tipos hoteleros y arquitectónicos, además de poner por primera vez en conexión distintos modelos de hotelería pública, para constituirse en el sustrato de futuras investigaciones. El estudio realizado se ha hecho extensivo a las distintas escalas que inciden de forma interconectada en la implantación de un parador: la arquitectónica, la urbana y la del interiorismo, hasta ahora referenciado desde la exclusiva visión arquitectónica. Se han definido las etapas de la historia de la red, no ya sólo a partir del hilo conductor de la cadena sucesiva de organismos turísticos, sino que por primera vez se hace en razón de la evolución que sufren las intervenciones patrimoniales a lo largo del tiempo, a la vez que se entra en conexión con la teoría y praxis de la restauración monumental. Con carácter particular, la arquitectura militar dentro del contexto de los paradores se destaca en el período del Ministerio, en el que se experimentaron todas las posibilidades que presentaba su rehabilitación. En este sentido se ha puesto de manifiesto en este trabajo un tipo híbrido de parador, a caballo entre la rehabilitación y la edificación de nueva planta, las dos formas básicas de establecimiento creadas en la Comisaría Regia, al que se ha denominado edificación de nueva planta en recinto histórico militar. Esta nueva caracterización se ha valorado como la forma más eficiente de implantar paradores, cuyas pautas arquitectónicas abarcaron un abanico de posibilidades: imitación de modelos arquitectónicos históricos con utilización de elementos patrimoniales prestados que dieran el valor de la historia, utilización de un lenguaje moderno, o la inspiración en la arquitectura vernácula. La amalgama de elementos, estilos e intervenciones sucesivas de ampliación fue la característica común tanto para la implantación de un parador en un edificio como en un recinto amurallado. La arquitectura militar transformada en establecimiento hotelero evidencia la vocación escenográfica de las intervenciones patrimoniales, secundada por el interiorismo, además de su aportación a la arquitectura hotelera en lo referente al confort, organización y funcionamiento de sus instalaciones. La tesis ahonda en los diversos aspectos de la rehabilitación hotelera apuntados de forma parcial por algunos autores, y pone de manifiesto la “ambientación medieval” operada en la arquitectura militar, que llegó a tener su máxima expresión con el criterio de la “unidad de estilo” del Ministerio de Información y Turismo. La rehabilitación hotelera dentro del contexto de la Red de Paradores, queda caracterizada en la tesis en relación a intervenciones en construcciones militares, cuya sistematización puede ser extrapolable a otros tipos arquitectónicos o cadenas hoteleras de titularidad pública, a partir del estudio que se ha avanzado en este trabajo. Thesis basis: At the beginning of the 20th century the interest in tourism added to the plentiful heritage in Spain enabled the authorities to embark on a singular experience: the creation of a hotel infrastructure from the restoration of historic buildings. Preservation, maintenance, and even profitability of a large part of the Spanish heritage would be effective through the innovative formula heritage-tourism. Its greatest expression materialized in the Paradores Network since its foundation in last century’s second decade to the present day. Surprisingly, this subject has not yet been investigated in its architectural aspect, even though Spain has been a pioneer and a model in the matter of public hotel business. This project tackles the study of the most significative case of all the network’s buildings, since the heritage which has served throughout history as a base for the State hotel purposes has altogether six architectural types, among which military architecture stands out with its majority presence in the context of the historical buildings of the network. The archetypal character of castles and fortresses, ingrained in the collective subconscious, made them specially attractive for tourist accommodation, as it allowed the evocation of far medieval times, despite being the most awkward architectural type for hotel restoration. The study of the interventions in these buildings clearly reveals itself as a showcase of the different criteria of heritage intervention along the 20th century, connecting to the present interdisciplinary perspective. Firstly, the thesis covers different general aspects regarding the hotel developer, the domestic and international public hotel business, and the description of the Spanish state network buildings from a hotel business and an architectural point of view, the latter from its three influence scales: architectural, urban or landscape, and interior design. Secondly, the transformation of the military architecture in the Paradores Network into hotels is analyzed. For that purpose it was necessary to create a specific classification, which included barrack-structured buildings, castle-palaces, or fortresses which served the purposes of military-religious orders. The interventions in those military historical places where new building became compulsory were also taken into consideration. Thirdly and lastly, the thesis analyses the restorations in these military constructions through the different stages of the tourist organization. In order to avoid decontextualization, interventions in other historical buildings were also considered. This route begins with the promotion of the two first Paradores by the Royal Commissioner, the marquis of Vega-Inclán, which paved the way for the concepts and ideas that were developed in the following decades. Subsequently, the network was developed and took shape with the National Tourism Board. The first interventions on military types were inside refurbishments. The Network’s key period, and in particular of its military architecture, took place with the Ministry of Information and Tourism, a time marked by the “restoration to its original state” of monuments. This stage arrived after a preparatory period with the State Tourist Office, when the military type was left as a backdrop for other architectural types. After the Ministry’s boom arrived a decline, in which castles and fortresses disappeared from the Tourist Department’s interests up to the opening of the 21st century new establishments and the resurgence of the military type with Lorca’s Parador. Methodology: The present research project has mainly used unpublished documentation from several archives and has done an extensive in situ data-gathering. Within the heritage analyzed, military buildings have been divided into three main groups: restored buildings that began to operate in the network, those in process of hotel transformation, and those acquired for hotel purposes, but which did not become restored. In each case, it has been necessary to determine the condition in which they arrived to the Tourist Administration, the procedure by which they were acquired, what their first hotel restoration consisted of, and which their subsequent most significative enlargements and alterations were. These facts have been synthesized in cards, and conclusions were drawn by comparing each unit with the whole. Simultaneously, two external factors were introduced: the history of tourism, that allowed establishing a chronological order according to different periods, and the history of Spanish heritage intervention’s theory and practice, that permitted to compare the heritage criteria from the competent Administration with those of the Tourist Administration’s interventions. Both Administrations came compulsorily into contact after the Decree of 22nd April 1949, by which all castles and fortresses became under the protection of the State. Thesis contribution: In general, the thesis focuses on a complete order and systematization of the network’s heritage buildings from the hotel and architectural types points of view, besides connecting for the first time different public hotel business models, becoming the substratum for future investigations. The study has included the different scales that impact interconnected on the establishment of a Parador: architectural, urban and interior design, only referenced to date from an architectural point of view. The Network’s history stages have been defined according to not only a consecutive series of tourist organizations, but also, and for the first time, to the evolution of heritage interventions over time, thus connecting with the theory and praxis of monumental restoration. In particular, within the Paradores, military architecture stands out in the Ministry’s period, in which all kind of restoration possibilities were explored. In this sense, the present project puts forth a hybrid type of Parador between restoration and new building, the two basic ways of establishment created in the Royal Commission, termed new building in military historic enclosure. This new characterization has been evaluated as the most efficient for establishing Paradores, whose architectonic guidelines include a wide range of possibilities: the imitation of historical architectonic models with use of borrowed heritage components that provide historical value, the use of modern language, or the inspiration in vernacular architecture. The amalgam of elements, styles and consecutive enlargement interventions was the common feature of the establishment of a Parador, both in a building or in a walled enclosure. The military architecture transformed into a hotel establishment gives proof of the scenographic vocation of heritage interventions, supported by interior design, as well as of its contribution to hotel architecture, related to its comfort, organization and the functioning of its facilities. The thesis delves into the diverse aspects of hotel restoration, partially pointed out by several authors, and puts forth the creation of a “medieval atmosphere” in military architecture, which came to its highest expression with the “unitary style” criteria of the Ministry of Information and Tourism. Hotel restoration within the context of the Paradores’ Network is defined in this thesis in relation to interventions in military constructions, whose systemization can be extrapolative to other architectural types or public hotel chains, based on the study which has been put forward in this project.

Application of a building cost estimation model to the appraisal of the churches damaged by earthquakes in Lorca (Spain)

The objective of this paper is the development of a building cost estimation model whose purpose is to quickly and precisely evaluate rebuilding costs for historic heritage buildings affected by catastrophic events. Specifically, this study will be applied to the monumental buildings owned by the Catholic Church that were affected by two earthquakes on May 11, 2011 in the town of Lorca. To estimate the initial total replacement cost new, calculation model will be applied which, on the one hand, will use two-dimensional metric exterior parameters and, on the other, three-dimensional interior cubic parameters. Based on the total of the analyzed buildings, and considering damage caused by the seismic event, the final reconstruction cost for the building units ruined by the earthquakes can be estimated. The proposed calculation model can also be applied to other emergency scenarios and situations for the quick estimation of construction costs necessary for rebuilding historic heritage buildings which have been affected by catastrophic events that deteriorate or ruin their structural or constructive configuration.

Assessment of Underground Wine Cellars Using Geographic Information Technologies

Geographic information technologies (GIT) are essential to many fields of research, such as the preservation and dissemination of cultural heritage buildings, a category which includes traditional underground wine cellars. This article presents a methodology based on research carried out on this type of rural heritage building. The data were acquired using the following sensors: EDM, total station, close-range photogrammetry and laser scanning, and subsequently processed with a specific software which was verified for each case, in order to obtain a satisfactory graphic representation of these underground wine cellars. Two key aspects of this work are the accuracy of the data processing and the visualization of these traditional constructions. The methodology includes an application for geovisualizing these traditional constructions on mobile devices in order to contribute to raising awareness of this unique heritage.

Comportamiento térmico y mecánico del yeso con adiciones de aerogel de sílice granulado

La presente tesis doctoral aborda el estudio de un nuevo material mineral, compuesto principalmente por una matriz de yeso (proveniente de un conglomerante industrial basado en sulfato de calcio multifase) y partículas de aerogel de sílice hidrófugo mesoporoso, compatibilizadas mediante un surfactante polimérico, debido a su alto carácter hidrófugo. La investigación se centra en conocer los factores que influyen en las propiedades mecánicas y conductividad térmica del material compuesto generado. Este estudio pretende contribuir al conocimiento sobre el desarrollo de nuevos morteros de elevado aislamiento térmico que puedan ser utilizados en la rehabilitación energética de edificios de viviendas existentes, debido a que estos representan gran parte del consumo energético del parque de viviendas de España, aunque también a nivel internacional. De los materiales utilizados para desarrollar los morteros estudiados, el yeso, además de ser un material muy abundante, especialmente en España, requiere una menor cantidad de energía para la fabricación de un conglomerante (debido a una menor temperatura de fabricación), en comparación con el cemento o la cal, por lo que presenta una menor huella de carbono que estos últimos. Por otro lado, el aerogel de sílice hidrófugo mesoporoso es, de acuerdo con la documentación disponible, el material que posee actualmente la mayor capacidad de aislamiento térmico en el mercado. El desarrollo de nuevos morteros minerales con una capacidad de aislamiento térmico mayor que los materiales aislantes utilizados tradicionalmente, tiene una aplicación relevante en los casos de rehabilitación energética de edificios históricos y patrimoniales, en los que se requiere la aplicación del aislamiento por el interior de la fachada, ya que este tipo de soluciones tienen el inconveniente de reducir el espacio habitable de las áreas involucradas, especialmente en zonas climáticas en las que el aislamiento térmico puede suponer un espesor considerable, por lo que es ideal utilizar materiales de altas prestaciones de aislamiento térmico capaces de aportar el mismo nivel de aislamiento (o incluso mayor), pero en un espesor considerablemente menor. La investigación se desarrolla en tres etapas: bibliográfica, experimental y de simulación. La primera etapa, parte del estudio de la bibliografía existente, relacionada con materiales aislantes, incluyendo soluciones basadas, tanto en morteros aislantes, como en paneles de aislamiento térmico. La segunda, de carácter experimental, se centra en estudiar la influencia de la microestrucrura y macroestructura, del nuevo material mineral, en las propiedades físicas elementales, mecánicas y conductividad térmica del compuesto. La tercera etapa, mediante una simulación del consumo energético, consiste en cuantificar teóricamente el potencial ahorro energético que puede aportar este material en un caso de rehabilitación energética en particular. La investigación experimental se centró principalmente en conocer los factores principales que influyen en las propiedades mecánicas y conductividad térmica de los materiales compuestos minerales desarrollados en esta tesis. Para ello, se llevó a cabo una caracterización de los materiales de estudio, así como el desarrollo de distintas muestras de ensayo, de tal forma que se pudo estudiar, tanto la hidratación del yeso en los compuestos, como su posterior microestructura y macroestructura, aspectos fundamentales para el entendimiento de las propiedades mecánicas y conductividad térmica del compuesto aislante. De este modo, se pudieron conocer y cuantificar, los factores que influyen en las propiedades estudiadas, aportando una base de conocimiento y entendimiento de este tipo de compuestos minerales con aerogel de sílice hidrófugo, no existiendo estudios publicados hasta el momento de finalización de esta tesis, con la aproximación al material propuesta en este estudio, ni con yeso (basado en sulfato de calcio multifase), ni con otro tipo de conglomerantes. Particularmente, se determinó la influencia que tiene la incorporación de partículas de aerogel de sílice hidrófugo, en grandes proporciones en volumen, en un compuesto mineral basado en distintas fases de sulfato de calcio. No obstante, para llevar a cabo las mezclas, fue necesario utilizar un surfactante para compatibilizar este tipo de partículas, con el conglomerante basado en agua. El uso de este tipo de aditivos tiene una influencia, no solo en el aerogel, sino en las propiedades del compuesto en general, dependiendo de su concentración, por lo que se establecieron dos porcentajes de adición: la primera, determinada a partir de la cantidad mínima necesaria para compatibilizar las mezclas (0,1% del agua de amasado), y la segunda, como límite superior, la concentración utilizada habitualmente a nivel industrial para estabilizar burbujas de aire en hormigones espumados (5%). El surfactante utilizado mostró la capacidad de modificar la superficie del aerogel, cambiando el comportamiento de las partículas frente al agua, permitiendo una invasión parcial de su estructura porosa, por parte del agua de amasado. Este comportamiento supone un aumento muy importante en la relación agua/yeso, afectando el hábito cristalino e influenciando negativamente las propiedades mecánicas de la matriz de yeso, presentando un efecto aún notable a mayor concentración de surfactante (5%). En cuanto a las propiedades finales alcanzadas, fue posible lograr un compuesto mineral ultraligero (200 kg/m3), con alrededor de un 60% de aerogel en volumen y de alta capacidad aislante (0,028 W/m•K), presentando una conductividad térmica notablemente menor que los morteros aislantes del mercado, e incluso también menor que la de los aislantes tradicionales basado en las lanas minerales o EPS; no obstante, con la limitante de presentar bajas propiedades mecánicas, condicionando su posible aplicación futura. Entre los factores principales relacionados con las propiedades mecánicas, se encontró que estas dependen exponencialmente del volumen de yeso en el compuesto; no obstante, factores de segundo orden, como el grado de hidratación, o una mejor distribución del conglomerante entre las partículas de aerogel, debido al aumento de la superficie específica del polvo mineral, pueden aumentar las propiedades mecánicas entre el doble y el triple, dependiendo del volumen de aerogel en cuestión. Además, se encontró que el aerogel, en conjunto con el surfactante, es capaz de introducir una gran cantidad de aire (0,70 m3 por cada m3 de aerogel), que unido al agua evaporada (no consumida por el conglomerante durante la hidratación), el volumen de aire total alcanza, generalmente, un 40%, independientemente de la cantidad de aerogel en la mezcla. De este modo, el aire introducido en la matriz desplaza las proporciones en volumen del aerogel y del yeso, disminuyendo, tanto las propiedades mecánicas, como la capacidad aislante de compuesto mineral. Por otro lado, la conductividad térmica mostró tener una dependencia directa de la contribución de las tres fases principales en el compuesto: yeso, aerogel y aire ocluido. De este modo, se pudo desarrollar un modelo matemático, adaptado de uno existente, capaz de calcular, con bastante precisión, la relación de los tres componentes mencionados, en la conductividad térmica de los compuestos, para el rango de volúmenes y materiales utilizados en esta tesis. Finalmente, la simulación del consumo energético realizada a una vivienda típica de España, de los años 1900 a 1959 (basada en muros de ladrillo macizo), para las zonas climáticas estudiadas (A, D y E), permitió observar el potencial ahorro energético que puede aportar este material, dependiendo de su espesor, como aislamiento interior de los muros de fachada. Particularmente, para la zona A, se determinó un espesor óptimo de 1 cm, mientras que para la zona D y E, 3,5 y 3,9 cm respectivamente. En este sentido, el nuevo material estudiado es capaz de disminuir, entre un 35% y un 80%, el espesor de la capa aislante, en comparación con paneles de lana de roca o los morteros minerales de mayor capacidad aislante del mercado español respectivamente. ABSTRACT The present doctoral thesis studies a new mineral-based composite material, composed by a gypsum matrix (based on an industrial multiphase gypsum binder) and mesoporous hydrophobic silica aerogel particles, compatibilized with a polymeric surfactant due to the high hydrophobic character of the insulating particles. This study pretends to contribute to the development of new composite insulating materials that could be used in energy renovation of existing dwellings, in order to reduce their high energy consumption, as they represent a great part of the total energy consumed in Spain, but also internationally. Between the materials used to develop de studied insulating mortars, gypsum, besides being an abundant material, especially in Spain, requires less energy for the manufacture of a mineral binder (due to lower manufacturing temperatures), compared to lime or cement, thus presenting lower carbon footprint. In other hand, the hydrophobic mesoporous silica aerogel, is, according to the existing references, the material with the highest know insulating capacity in the market. The development of new mineral mortars with higher thermal insulation capacity than traditional insulating materials, presents a relevant application in energy retrofitting of historic and cultural heritage buildings, in which implies that the insulating material should be installed as an internal layer, rather than as an external insulating system. This type of solution involves a reduced internal useful area, especially in climatic zones where the demand for thermal insulation is higher, and so the insulating layer thickness, being idealistic to use materials with very high insulating properties, in order to reach same insulating level (or higher), but in lower thickness than the provided by traditional insulating materials. This research is developed in three main stages: bibliographic, experimental and simulation. The first stage starts by studying the existing references regarding thermally insulating materials, including existing insulating mortars and insulating panels. The second stage, mainly experimental, is centered in the study of the the influence of the microstructure and macrostructure in the physical and mechanical properties, and also in the thermal conductivity of the new mineral-based material. The thirds stage, through energy simulation, consists in theoretically quantifying the energy savings potential that can provide this type of insulating material, in a particular energy retrofitting case study. The experimental research is mainly focused in the study of the factors that influence the mechanical properties and the thermal conductivity of the thermal insulating mineral composites developed in this thesis. For this, the characterization of the studied materials has been performed, as well as the development of several experimental samples, in order to study the hydration of the mineral binder within the composites, but also the final microstructure and macrostructure, fundamental aspects for the understanding of the composite’s mechanical and insulating properties. Thus, is was possible to determine and quantify the factors that influence the studied material properties, providing a knowledge base and understanding of mineral composites that comprises mesoporous hydrophobic silica aerogel particles, being the first study up to date regarding the specific approach of the present study, regarding not just multiphase calcium sulfate plaster, but also other mineral binders. Particularly, the influence of the incorporation of hydrophobic silica aerogel particles, in high volume ratios into a mineral compound, based on different phases of calcium sulfate has been determined. However, to perform mixing, it is necessary to use a surfactant in order to compatibilize these particles with the water-based mineral binder. The use of such additives has an influence, not only in the aerogel, but the overall properties of the compound, so two different surfactant concentration has been studied: the first, the minimum amount of surfactant (used in this thesis) in order to develop the slurries (0.1% concentration of the mixing water), and the second, as the upper limit, the concentration usually used industrially to stabilize air bubbles in foamed concrete (5%). One of the side effects of using such additive, was the modification of the aerogel particles, by changing their behavior in respect to water, generating a partial invasion of the aerogel’s porous structure, by the mixing water. This behavior produces a very important increase in water/binder ratios, affecting the crystal habit and negatively influencing the mechanical properties of the gypsum matrix. This effect further increased when a higher concentration of surfactant (5%) is used. Regarding final materials properties, it was possible to achieve an ultra-lightweight mineral composite (200 kg/m3), with around 60% by volume of aerogel, presenting a very high insulating capacity (0.028 W/m•K), a noticeable lower thermal conductivity compared to the insulating mortars and traditional thermal insulating panels on the market, such as mineral wool or EPS; however, the limiting factor for future’s material application in buildings, is related to the very low mechanical properties achieved. Among the main factors related to the mechanical properties, it has been found an exponential correlation to the volume of gypsum in the composite. However, second-order factors such as the degree of hydration, or a better distribution of the binder between the aerogel particles, due to the increased surface area of the mineral powder, can increase the mechanical properties between two to three times, depending aerogel volume involved. In addition, it was found that the aerogel, together with the surfactant, is able to entrain a large amount of air volume (around 0.70 m3 per m3 of aerogel), which together with the evaporated water (not consumed by the binder during hydration), can reach generally around 40% of entrained air within the gypsum matrix, regardless of the amount of aerogel in the mixture. Thus, the entrained air into the matrix displaces the volume proportions of the aerogel and gypsum, reducing both mechanical and insulating properties of the mineral composite. On the other hand, it has been observed a direct contribution of three main phases into the thermal conductivity of the composite: gypsum, aerogel and entrained air. Thus, it was possible to develop a mathematical model (adapted from an existing one), capable of calculating quite accurate the thermal conductivity of such mineral composites, from the ratio these three components and for the range of volumes and materials used in this thesis. Finally, the energy simulation performed to a typical Spanish dwelling, from the years 1900 to 1959 (mainly constructed with massive clay bricks), within three climatic zones of Spain (A, D and E), showed the energy savings potential that can provide this type of insulating material, depending on the thickness of the applied layer. Particularly, for the climatic A zone, it has been found an optimal layer thickness of 1 cm, while for zone D and E, 3.5 and 3.9 cm respectively. In this manner, the new studied materials is capable of decreasing the thickness of the insulating layer by 35% and 80%, compared with rock wool panels or mineral mortars with the highest insulating performance of the Spanish market respectively.

Integrated studies for the evaluation of conservation treatments on buildings materials from archaeological sites: application to the case of Merida (Spain)

The application of conservation treatments, such as consolidation and protection ones, has been demonstrated ineffective in many cases, and even harmful. Evaluation studies should be a mandatory task, ideally before and after the intervention, but both tasks are complex and unusual in the case of archaeological heritage. This study is mainly focused on analyzing changes in petrophysical properties of stone material from archaeological sites of Merida (Spain), evaluating, both on site and in laboratory, effects derived from different conservation treatments applied in past interventions, throughout the integration of different non-destructive techniques (NDT) and portable devices of analysis available at the Institute of Geosciences (CSIC,UCM). These techniques allow, not only assessment of effectiveness and alteration processes, but also monitoring durability of treatments, focused mainly on 1996 intervention in the case of Roman Theater, as well as different punctual interventions from the 90?s until date in the House of Mitreo. Studies carried out on archaeological sites of Merida permit us to compare outcomes and also check limitations in the use of those equipments. In this paper we discuss about the use of some techniques, their integration and limits, for the assessment of conservation treatments, showing some examples of Merida?s case study.

Mejora del comportamiento térmico de los morteros de cal aditivados y su empleo en la rehabilitación de inmuebles = Improvement of thermal behaviour of additived lime mortars and their use in rehabilitation of buildings

La envolvente de la edificación es la responsable de equilibrar el intercambio energético entre el interior y el exterior, por lo tanto cualquier actuación encaminada a la reducción del consumo energético ha de establecer, como uno de sus objetivos prioritarios, la mejora del comportamiento de la misma. Las edificaciones anteriores a 1940 constituyen la mayor parte de las existentes en áreas rurales y centros urbanos. En ellas, la repercusión de la fachada sobre las transmitancias globales pone de manifiesto la necesidad de intervención. Sin embargo, su elevada inercia térmica y los importantes saltos térmicos característicos de gran parte de España plantean la importancia de que aquélla se efectúe por el exterior. A tal respecto, la falta de disponibilidad de espesor suficiente para implantar sistemas tipo SATE deriva en que, frecuentemente, la única solución viable sea la de aislar por el interior perdiendo con ello la capacidad de acumulación térmica del muro y con el asociado riesgo de condensaciones. La amplia tradición en el empleo de revestimientos, especialmente en base de cal, permiten que éstos sean utilizados no sólo como elemento estético o de protección de la obra de fábrica antigua sino también para la mejora del comportamiento térmico del soporte, si se aprovecha el mecanismo de transmisión térmica por radiación. Éste es el objetivo de la presente Tesis Doctoral en la que se estudia la modificación de las propiedades radiantes de los morteros de revestimiento para la mejora de la eficiencia energética de las construcciones históricas, principalmente las constituidas por muros monolíticos, aunque podría ser de aplicación a otro tipo de construcciones compuestas por diversas capas. Como punto de partida, se estudió y revisó la documentación disponible sobre las investigaciones de las tres áreas científico-tecnológicas que convergen en la Tesis Doctoral: rehabilitación, material y comportamiento térmico, a partir de lo cual se comprobó la inexistencia de estudios similares al objeto de la presente Tesis Doctoral. Complementariamente, se analizaron los revestimientos en lo concerniente a los materiales que los constituyen, la composición de las mezclas y características de cada una de las capas así como al enfoque que, desde el punto de vista térmico, se estimaba más adecuado para la obtención de los objetivos propuestos. Basándonos en dichos análisis, se preseleccionaron ochenta materiales que fueron ensayados en términos de reflectancia y emisividad para elegir cuatro con los que se continuó la investigación. Éstos, junto con la cal elegida para la investigación y el árido marmóreo característico de la última capa de revestimiento, fueron caracterizados térmicamente, de forma pormenorizada, así como química y físicamente. Los fundamentos teóricos y los estudios preliminares desarrollados con distintos materiales, en estado fresco y endurecido, fueron empleados en la dosificación de componentes de las mezclas, en dos proporciones distintas, para el estudio del efecto del agregado. Éstas se ensayaron en estado fresco, para comprobar su adecuación de puesta en obra y prever su VI adherencia al soporte, así como en estado endurecido a 28 y 90 días de curado, para conocer las propiedades que permitieran prever su compatibilidad con aquél y estimar el alcance de la reducción de transferencias térmicas lograda. Además, se estudiaron las características generales de las mezclas que sirvieron para establecer correlaciones entre distintas propiedades y entender los resultados mecánicos, físicos (comportamiento frente al agua) y energéticos. Del estudio conjunto de las distintas propiedades analizadas se propusieron dos mezclas, una blanca y otra coloreada, cuyas características permiten garantizar la compatibilidad con la obra de fábrica antigua, desde el punto de vista físico y mecánico, y preservar la autenticidad de los revestimientos, en cuanto a la técnica de aplicación tradicional en sistemas multicapa. El comportamiento térmico de las mismas, sobre una obra de fábrica de 40 cm de espesor, se estimó, en estado estacionario y pseudo-transitorio, demostrándose reducciones del flujo térmico entre 16-48%, en condiciones de verano, y entre el 6-11%, en invierno, en función de la coloración y de la rugosidad de la superficie, en comparación con el empleo de la mezcla tradicional. Por lo que, se constata la viabilidad de los materiales compuestos propuestos y su adecuación al objetivo de la investigación. VII ABSTRACT The envelope is responsible for balancing the energy exchange between the inside and outside in buildings. For this reason, any action aimed at reducing energy consumption must establish, as one of its key priorities, its improvement. In rural areas and urban centers, most of the constructions were built before 1940. In them, the impact of the façade on the global transmittance highlights the need for intervention. However, its high thermal inertia and fluctuation of temperatures in the majority of Spain bring up that it should be placed outside the insulation. In this regard, the lack of availability of enough thickness to implement systems such as ETICS results in that often the only viable solution is to isolate the interior, losing thereby the wall’s heat storage capacity with the associated risk of condensation. The tradition in the use of renders, especially lime-based, allows us to use them not only as an aesthetic element or to protect the ancient masonry, but also for improved thermal performance of the support by taking advantage of the heat transfer mechanism by radiation. This is the aim of this Doctoral Thesis in which the modification of the radiative properties of lime mortars for renders to improve the energy efficiency of historic buildings, mainly composed of monolithic walls, is studied, although it could be applied to other structures composed of several layers. As a starting point, the available literature in the three scientific-technological areas that converge at the Doctoral Thesis: rehabilitation, material and thermal behaviour, was reviewed, and confirmed the absence of researches similar to this Doctoral Thesis. Additionally, the renders were studied with regard to the materials that constitute them, the composition of the mixtures and the characteristics of each layer, as well as to the approach which, from a thermal point of view, was deemed the most suitable for achieving the objectives sets. Based on thre aforementioned analysis, eighty materials tested in terms of reflectance and emissivity were pre-selected, to choose four with which the research was continued. Common marble sand, used in the last layer of the renders, together with the appointed materials and hydrated lime were characterized thermally, in detail, as well as chemically and physically. The theoretical bases and preliminary studies with different materials, in fresh and hardened state, were used in the dosage of the composition of the mixtures. In order to study their effect they were used in two different proportions, that is, ten mixtures in total. These were tested in their fresh state to evaluate their setting-up suitability and foresee their adhesion to the support, as well as in their hardened state, at 28 and 90 days of curing, to establish the properties which enabled us to anticipate their compatibility with the old masonry walls and estimate the scope of the reduction of heat transfers achieved. In addition, the general characteristics of the mixtures used to establish correlations and to understand the mechanical, physical and energy results were studied. Two mixtures, one white and one colored, were proposed as the result of the different properties analysed, whose characteristics allow the guarantee of mechanical and physical compatibility VIII with the old masonry and preserve the authenticity of the renders. The thermal behavior of both, applied on a masonry wall 40 cm thick, was estimated at a steady and pseudo-transient state, with heat flow reductions between 16-48% during summertime and 6-11% during wintertime, depending on the color and surface roughness, compared to the use of the traditional mixture. So, the viability of the proposed composite materials and their fitness to the aim of the research are established.

Traditional Building Adaptation to New Requirements: Historic Center of Arequipa, Perú

The traditional buildings in the historic center of the city of Arequipa, Perú, recently declared of human heritage, are of volcanic tuff both in walls and in vaulted roofs on the ground floor. Having been built in the 18th century and up to the beginning of the 20th century, they have suffered many damages from the seismic movements registered in this region. Due to this, many of them have had to be rebuilt. In this presentation, the different changes to adapt the city of Spanish colonial origin to the present tertiary use are analyzed.

Patrimonio Histórico Minero-Metalúrgico, Patrimonio Cultural/ Mining-Metallurgical Historical Heritage, Cultural Heritage

El panel se divide en tres secciones : Minería histórica , Patrimonio Minero y Museos.

The value of cultural assets. Maintenance Costs and economic sustainability at heritage

Under the 12th International Conference on Building Materials and Components is inserted this communication related to the field of management of those assets that constitute the Spanish Cultural Heritage and maintenance. This work is related to the field of management of those assets that constitute the Spanish Cultural Heritage which share an artistic or historical background. The conservation and maintenance become a social demand necessary for the preservation of public values, requiring the investment of necessary resources. The legal protection involves a number of obligations and rights to ensure the conservation and heritage protection. The duty of maintenance and upkeep exceeds the useful life the property that must endure more for their cultural value for its usability. The establishment of the necessary conditions to prevent deterioration and precise in order to fulfill its social function, seeking to prolong the life of the asset, preserving their physical integrity and its ability to convey the values protected. This obligation implies a substantial financial effort to the holder of the property, either public or private entity, addressing a problem of economic sustainability. Economic exploitation, with the aim of contributing to their well-maintained, is sometimes the best way to get resources. The work will include different lines of research with the following objectives. - Establishment of processes for assessing total costs over the building life cycle (LCC), during the planning stages or maintenance budgets to determine the most advantageous operating system. - Relationship between the value of property and maintenance costs, and establishing a sensitivity analysis.

Metadata Visualization of Cultural Heritage Information within a Collaborative Environment

Cultural content on the Web is available in various domains (cultural objects, datasets, geospatial data, moving images, scholarly texts and visual resources), concerns various topics, is written in different languages, targeted to both laymen and experts, and provided by different communities (libraries, archives museums and information industry) and individuals (Figure 1). The integration of information technologies and cultural heritage content on the Web is expected to have an impact on everyday life from the point of view of institutions, communities and individuals. In particular, collaborative environment scan recreate 3D navigable worlds that can offer new insights into our cultural heritage (Chan 2007). However, the main barrier is to find and relate cultural heritage information by end-users of cultural contents, as well as by organisations and communities managing and producing them. In this paper, we explore several visualisation techniques for supporting cultural interfaces, where the role of metadata is essential for supporting the search and communication among end-users (Figure 2). A conceptual framework was developed to integrate the data, purpose, technology, impact, and form components of a collaborative environment, Our preliminary results show that collaborative environments can help with cultural heritage information sharing and communication tasks because of the way in which they provide a visual context to end-users. They can be regarded as distributed virtual reality systems that offer graphically realised, potentially infinite, digital information landscapes. Moreover, collaborative environments also provide a new way of interaction between an end-user and a cultural heritage data set. Finally, the visualisation of metadata of a dataset plays an important role in helping end-users in their search for heritage contents on the Web.

Methodology for the metric restoration of the historical cartography applied to Francisco Coello's cartografic series of the Royal Site of Aranjuez

Hojas Kilométricas (Kilometric Sheets). Specifically, the study focuses on those sheets referring to the city centre and surrounding area of the Royal Site of Aranjuez, a town in the south of the Province of Madrid. The aim of this study is to restore the actual size and measurements of scanned images of the Hojas Kilométricas. This would allow us, among other things, to reestablish both the format and scale of the original plans. To achieve this goal it is necessary to rectify and then georeference these images, i.e. assign them a geographic reference system. This procedure is essential in the overlaying and comparison of the Hojas Kilométricas of the Royal Site with other historical cartography as well as other sources related to the same area from different time periods. Subsequent research would allow us, for example, to reconstruct the time-evolution of the urban area, to spot new construction and to pinpoint the locations of any altered or missing buildings or architectural features. In addition, this would allow us to develop and integrate databases for GIS models applicable to the management of our cultural heritage.

Impact And Explosive Loads On Concrete Buildings Using Shell And Beam Type Elements

The threat of impact or explosive loads is regrettably a scenario to be taken into account in the design of lifeline or critical civilian buildings. These are often made of concrete and not specifically designed for military threats. Numerical simulation of such cases may be undertaken with the aid of state of the art explicit dynamic codes, however several difficult challenges are inherent to such models: the material modeling for the concrete anisotropic failure, consideration of reinforcement bars and important structural details, adequate modeling of pressure waves from explosions in complex geometries, and efficient solution to models of complete buildings which can realistically assess failure modes. In this work we employ LS-Dyna for calculation, with Lagrangian finite elements and explicit time integration. Reinforced concrete may be represented in a fairly accurate fashion with recent models such as CSCM model [1] and segregated rebars constrained within the continuum mesh. However, such models cannot be realistically employed for complete models of large buildings, due to limitations of time and computer resources. The use of structural beam and shell elements for this purpose would be the obvious solution, with much lower computational cost. However, this modeling requires careful calibration in order to reproduce adequately the highly nonlinear response of structural concrete members, including bending with and without compression, cracking or plastic crushing, plastic deformation of reinforcement, erosion of vanished elements etc. The main objective of this work is to provide a strategy for modeling such scenarios based on structural elements, using available material models for structural elements [2] and techniques to include the reinforcement in a realistic way. These models are calibrated against fully three-dimensional models and shown to be accurate enough. At the same time they provide the basis for realistic simulation of impact and explosion on full-scale buildings

Normalización del análisis de la piedra y conservación del patrimonio cultural. The Standardization of Stone Analysis and Conservation of Cultural Heritage

La normalización de los métodos de análisis y de los principales aspectos relacionados con la conservación de los bienes culturales ha empezado en 2004 con la creación del comité europeo de normalización, CEN/TC 346 Conservation of Cultural Property, que tiene la responsabilidad no solamente de redactar protocolos de ensayos en laboratorio, sino también proponer las recomendaciones más adecuadas para designarlos de forma consensual y conservarlos de la forma más apropiada. Se comentan los aspectos relacionados con el origen de estas normas, el trabajo desarrollado y que muchas de ellas, aunque no estén dirigidas específicamente a la piedra, tienen en cuenta la presencia de este material en objetos arqueológicos, obras de arte, estructuras de fábricas y elementos ornamentales.

New Constructive Solutions to Improve Energy Efficiency in Existing Buildings and their Economic Viability

The improvement of energy efficiency in existing buildings is always a challenge due to their particular, and sometimes protected, constructive solutions. New constructive regulations in Spain leave a big undefined gap when a restoration is considered because they were developed for new buildings. However, rehabilitation is considered as an opportunity for many properties because it allows owners to obtain benefits from the use of the buildings. The current financial and housing crisis has turned society point of view to existing buildings and making them more efficient is one of the Spanish government’s aims. The economic viability of a rehabilitation action should take all factors into account: both construction costs and the future operative costs of the building must be considered. Nevertheless, the application of these regulations in Spain is left to the designer’s opinion and always under a subjective point of view. With the research work described in this paper and with the help of some case-studies, the cost of adapting an existing building to the new constructive regulations will be studied and Energetic Efficiency will be evaluated depending on how the investment is recovered. The interest of the research is based on showing how new constructive solutions can achieve higher levels of efficiency in terms of energy, construction and economy and it will demonstrate that Life Cycle Costing analysis can be a mechanism to find the advantages and disadvantages of using these new constructive solutions. Therefore, this paper has the following objectives: analysing constructive solutions in existing buildings - to establish a process for assessing total life cycle costs (LCC) during the planning stages with consideration of future operating costs - to select the most advantageous operating system – To determine the return on investment in terms of construction costs based on new techniques, the achieved energy savings and investment payback periods.

Assessing the solar irradiation potential for solar photovoltaic applications in buildings at low latitudes ¿ Making the case for Brazil

In Brazil, a low-latitude country characterized by its high availability and uniformity of solar radiation, the use of PV solar energy integrated in buildings is still incipient. However, at the moment there are several initiatives which give some hints that lead to think that there will be a change shortly. In countries where this technology is already a daily reality, such as Germany, Japan or Spain, the recommendations and basic criteria to avoid losses due to orientation and tilt are widespread. Extrapolating those measures used in high latitudes to all regions, without a previous deeper analysis, is standard practice. They do not always correspond to reality, what frequently leads to false assumptions and may become an obstacle in a country which is taking the first step in this area. In this paper, the solar potential yield for different surfaces in Brazilian cities (located at latitudes between 0° and 30°S) are analyzed with the aim of providing the necessary tools to evaluate the suitability of the buildings’ envelopes for photovoltaic use