Canonical Correlation Analysis for Interpreting Airborne Laser Scanning Metrics along the Lorenz Curve of Tree Size Inequality

Canonical Correlation Analysis for Interpreting Airborne Laser Scanning Metrics along the Lorenz Curve of Tree Size Inequality

Low cost 3D global instability analysis and flow sensitivity based on dynamic mode decomposition and high-order numerical tools

We explore the recently developed snapshot-based dynamic mode decomposition (DMD) technique, a matrix-free Arnoldi type method, to predict 3D linear global flow instabilities. We apply the DMD technique to flows confined in an L-shaped cavity and compare the resulting modes to their counterparts issued from classic, matrix forming, linear instability analysis (i.e. BiGlobal approach) and direct numerical simulations. Results show that the DMD technique, which uses snapshots generated by a 3D non-linear incompressible discontinuous Galerkin Navier?Stokes solver, provides very similar results to classical linear instability analysis techniques. In addition, we compare DMD results issued from non-linear and linearised Navier?Stokes solvers, showing that linearisation is not necessary (i.e. base flow not required) to obtain linear modes, as long as the analysis is restricted to the exponential growth regime, that is, flow regime governed by the linearised Navier?Stokes equations, and showing the potential of this type of analysis based on snapshots to general purpose CFD codes, without need of modifications. Finally, this work shows that the DMD technique can provide three-dimensional direct and adjoint modes through snapshots provided by the linearised and adjoint linearised Navier?Stokes equations advanced in time. Subsequently, these modes are used to provide structural sensitivity maps and sensitivity to base flow modification information for 3D flows and complex geometries, at an affordable computational cost. The information provided by the sensitivity study is used to modify the L-shaped geometry and control the most unstable 3D mode.

The Proper Generalized Decomposition With Application In Problems Of Dynamics

In this paper we address the new reduction method called Proper Generalized Decomposition (PGD) which is a discretization technique based on the use of separated representation of the unknown fields, specially well suited for solving multidimensional parametric equations. In this case, it is applied to the solution of dynamics problems. We will focus on the dynamic analysis of an one-dimensional rod with a unit harmonic load of frequency (ω) applied at a point of interest. In what follows, we will present the application of the methodology PGD to the problem in order to approximate the displacement field as the sum of the separated functions. We will consider as new variables of the problem, parameters models associated with the characteristic of the materials, in addition to the frequency. Finally, the quality of the results will be assessed based on an example.

Instability and topology bifurcations on a hemisphere-cylinder at high angle of attack

La configuración de un cilindro acoplado a una semi-esfera, conocida como ’hemispherecylinder’, se considera como un modelo simplificado para numerosas aplicaciones industriales tales como fuselaje de aviones o submarinos. Por tanto, el estudio y entendimiento de los fenómenos fluidos que ocurren alrededor de dicha geometría presenta gran interés. En esta tesis se muestra la investigación del origen y evolución de los, ya conocidos, patrones de flujo (burbuja de separación, vórtices ’horn’ y vórtices ’leeward’) que se dan en esta geometría bajo condiciones de flujo separado. Para ello se han llevado a cabo simulaciones numéricas (DNS) y ensayos experimentales usando la técnica de Particle Image Velocimetry (PIV), para una variedad de números de Reynolds (Re) y ángulos de ataque (AoA). Se ha aplicado sobre los resultados numéricos la teoría de puntos críticos obteniendo, por primera vez para esta geometría, un diagrama de bifurcaciones que clasifica los diferentes regímenes topológicos en función del número de Reynolds y del ángulo de ataque. Se ha llevado a cabo una caracterización completa sobre el origen y la evolución de los patrones estructurales característicos del cuerpo estudiado. Puntos críticos de superficie y líneas de corriente tridimensionales han ayudado a describir el origen y la evolución de las principales estructuras presentes en el flujo hasta alcanzar un estado de estabilidad desde el punto de vista topológico. Este estado se asocia con el patrón de los vórtices ’horn’, definido por una topología característica que se encuentra en un rango de números de Reynolds muy amplio y en regímenes compresibles e incompresibles. Por otro lado, con el objeto de determinar las estructuras presentes en el flujo y sus frecuencias asociadas, se han usado distintas técnicas de análisis: Proper Orthogonal Decomposition (POD), Dynamic Mode Decomposition (DMD) y análisis de Fourier. Dichas técnicas se han aplicado sobre los datos experimentales y numéricos, demostrándose la buena concordancia entre ambos resultados. Finalmente, se ha encontrado en ambos casos, una frecuencia dominante asociada con una inestabilidad de los vórtices ’leeward’. ABSTRACT The hemisphere-cylinder may be considered as a simplified model for several geometries found in industrial applications such as aircrafts’ fuselages or submarines. Understanding the complex flow phenomena that surrounds this particular geometry is therefore of major industrial interest. This thesis presents an investigation of the origin and evolution of the complex flow pattern; i.e. separation bubbles, horn vortices and leeward vortices, around the hemisphere-cylinder under separated flow conditions. To this aim, threedimensional Direct Numerical Simulations (DNS) and experimental tests, using Particle Image Velocimetry (PIV) techniques, have been performed for a variety of Reynolds numbers (Re) and angles of attack (AoA). Critical point theory has been applied to the numerical simulations to provide, for the first time for this geometry, a bifurcation diagram that classifies the different flow topology regimes as a function of the Reynolds number and the angle of attack. A complete characterization about the origin and evolution of the complex structural patterns of this geometry has been put in evidence. Surface critical points and surface and volume streamlines were able to describe the main flow structures and their strong dependence with the flow conditions up to reach the structurally stable state. This state was associated with the pattern of the horn vortices, found on ranges from low to high Reynolds numbers and from incompressible to compressible regimes. In addition, different structural analysis techniques have been employed: Proper Orthogonal Decomposition (POD), Dynamic Mode Decomposition (DMD) and Fourier analysis. These techniques have been applied to the experimental and numerical data to extract flow structure information (i.e. modes and frequencies). Experimental and numerical modes are shown to be in good agreement. A dominant frequency associated with an instability of the leeward vortices has been identified in both, experimental and numerical results.

Calibration of calculation models of wooden guardrails with Operational Modal Analysis

This study analyses the differences between two calculation models for guardrails on building sites that use wooden boards and tubular steel posts. Wood was considered an isotropic material in one model and an orthotropic material in a second model. The elastic constants of the wood were obtained with ultrasound. Frequencies and vibration modes were obtained for both models through linear analysis using the finite element method. The two models were experimentally calibrated through operational modal analysis. The results obtained show that for the three types of wood under analysis, the model which considered them as an orthotropic material fitted the experimental results better than the model which considered them as an isotropic material.

A non-perturbative renormalization group study of the stochastic NavierStokes equation

We study the renormalization group flow of the average action of the stochastic Navier-Stokes equation with power-law forcing. Using Galilean invariance, we introduce a nonperturbative approximation adapted to the zero-frequency sector of the theory in the parametric range of the Hölder exponent 4−2 ɛ of the forcing where real-space local interactions are relevant. In any spatial dimension d, we observe the convergence of the resulting renormalization group flow to a unique fixed point which yields a kinetic energy spectrum scaling in agreement with canonical dimension analysis. Kolmogorov's −5/3 law is, thus, recovered for ɛ=2 as also predicted by perturbative renormalization. At variance with the perturbative prediction, the −5/3 law emerges in the presence of a saturation in the ɛ dependence of the scaling dimension of the eddy diffusivity at ɛ=3/2 when, according to perturbative renormalization, the velocity field becomes infrared relevant.

Implicaciones de la accesibilidad configuracional en la movilidad peatonal. El caso de Madrid = The implications of configurational accessibility in pedestrian mobility. The case of Madrid

- Resumen La hipótesis que anima esta tesis doctoral es que algunas de las características del entorno urbano, en particular las que describen la accesibilidad de su red de espacio público, podrían estar relacionadas con la proporción de viajes a pie o reparto modal, que tiene cada zona o barrio de Madrid. Uno de los puntos de partida de dicha hipótesis que el entorno urbano tiene una mayor influencia sobre los viaje a pie que en sobre otros modos de transporte, por ejemplo que en los viajes de bicicleta o en transporte público; y es que parece razonable suponer que estos últimos van a estar más condicionadas por ejemplo por la disponibilidad de vías ciclistas, en el primer caso, o por la existencia de un servicio fiable y de calidad, en el segundo. Otra de las motivaciones del trabajo es que la investigación en este campo de la accesibilidad del espacio público, en concreto la denominada “Space Syntax”, ha probado en repetidas ocasiones la influencia de la red de espacio público en cómo se distribuye la intensidad del tráfico peatonal por la trama urbana, pero no se han encontrado referencias de la influencia de dicho elemento sobre el reparto modal. De acuerdo con la hipótesis y con otros trabajos anteriores se propone una metodología basada en el análisis empírico y cuantitativo. Su objetivo es comprobar si la red de espacio público, independientemente de otras variables como los usos del suelo, incluso de las variables de ajenas entorno no construido, como las socioeconómicas, está o no relacionada estadísticamente con la proporción de peatones viajes en las zonas urbanas. Las técnicas estadísticas se utilizan para comprobar sistemáticamente la asociación de las variables del entorno urbano, denominadas variables independientes, con el porcentaje de viajes a pie, la variable dependiente. En términos generales, la metodología es similar a la usada en otros trabajos en este campo como los de CERVERÓ y KOCKLEMAN (1997), CERVERÓ y DUNCAN (2003), o para los que se utilizan principalmente en la revisión general de TRB (2005) o, más recientemente, en ZEGRAS (2006) o CHATMAN (2009). Otras opciones metodológicas, como los métodos de preferencias declaradas (ver LOUVIERE, HENSHER y SWAIT, 2000) o el análisis basado en agentes (PENN & TURNER, 2004) fueron descartados, debido a una serie de razones, demasiado extensas para ser descritas aquí. El caso de estudio utilizado es la zona metropolitana de Madrid, abarcándola hasta la M-50, es decir en su mayor parte, con un tamaño aproximado de 31x34 Km y una población de 4.132.820 habitantes (aproximadamente el 80% de la población de la región). Las principales fuentes de datos son la Encuesta Domiciliaria de Movilidad de 2004 (EDM04), del Consorcio Regional de Transportes de Madrid que es la última disponible (muestra: > 35.000 familias,> 95.000 personas), y un modelo espacial del área metropolitana, integrando el modelo para calcular los índices de Space Syntax y un Sistema de Información Geográfica (SIG). La unidad de análisis, en este caso las unidades espaciales, son las zonas de transporte (con una población media de 7.063 personas) y los barrios (con una población media de 26.466 personas). Las variables del entorno urbano son claramente el centro del estudio. Un total de 20 índices (de 21) se seleccionan de entre los más relevantes encontrados en la revisión de la producción científica en este campo siendo que, al mismo tiempo, fueran accesibles. Nueve de ellos se utilizan para describir las características de los usos del suelo, mientras que otros once se usan para describir la red de espacios públicos. Estos últimos incluyen las variables de accesibilidad configuracional, que son, como se desprende de su título, el centro del estudio propuesto. La accesibilidad configuracional es un tipo especial de accesibilidad que se basa en la configuración de la trama urbana, según esta fue definida por HILLIER (1996), el autor de referencia dentro de esta línea de investigación de Space Syntax. Además se incluyen otras variables de la red de espacio público más habituales en los estudios de movilidad, y que aquí se denominan características geométricas de los elementos de la red, tales como su longitud, tipo de intersección, conectividad, etc. Por último se incluye además una variable socioeconómica, es decir ajena al entorno urbano, para evaluar la influencia de los factores externos, pues son varios los que pueden tener un impacto en la decisión de caminar (edad, género, nivel de estudios, ingresos, tasa de motorización, etc.). La asociación entre las variables se han establecido usando análisis de correlación (bivariante) y modelos de análisis multivariante. Las primeras se calculan entre por pares entre cada una de las 21 variables independientes y la dependiente, el porcentaje de viajes a pie. En cuanto a los segundos, se han realizado tres tipos de estudios: modelo multivariante general lineal, modelo multivariante general curvilíneo y análisis discriminante. Todos ellos son capaces de generar modelos de asociación entre diversas variables, pudiéndose de esta manera evaluar con bastante precisión en qué medida cada modelo reproduce el comportamiento de la variable dependiente, y además, el peso o influencia de cada variable en el modelo respecto a las otras. Los resultados fundamentales del estudio se expresan en dos modelos finales alternativos, que demuestran tener una significativa asociación con el porcentaje de viajes a pie (R2 = 0,6789, p <0,0001), al explicar las dos terceras partes de su variabilidad. En ellos, y en general en todo el estudio realizado, se da una influencia constante de tres índices en particular, que quedan como los principales. Dos de ellos, de acuerdo con muchos de los estudios previos, corresponden a la densidad y la mezcla de usos del suelo. Pero lo más novedoso de los resultados obtenidos es que el tercero es una medida de la accesibilidad de la red de espacio público, algo de lo que no había referencias hasta ahora. Pero, ¿cuál es la definición precisa y el peso relativo de cada uno en el modelo, es decir, en la variable independiente? El de mayor peso en la mayor parte de los análisis realizados es el índice de densidad total (n º residentes + n º puestos de trabajo + n º alumnos / Ha). Es decir, una densidad no sólo de población, sino que incluye algunas de las actividades más importantes que pueden darse una zona para generar movilidad a pie. El segundo que mayor peso adquiere, llegando a ser el primero en alguno de los análisis estadísticos efecturados, es el índice de accesibuilidad configuracional denominado integración de radio 5. Se trata de una medida de la accesibilidad de la zona, de su centralidad, a la escala de, más un menor, un distrito o comarca. En cuanto al tercero, obtiene una importancia bastante menor que los anteriores, y es que representa la mezcla de usos. En concreto es una medida del equilibrio entre los comercios especializados de venta al por menor y el número de residentes (n º de tiendas especializadas en alimentación, bebidas y tabaco / n º de habitantes). Por lo tanto, estos resultados confirman buena parte de los de estudios anteriores, especialmente los relativas a los usos del suelo, pero al mismo tiempo, apuntan a que la red de espacio público podría tener una influir mayor de la comprobada hasta ahora en la proporción de peatones sobre el resto de modos de transportes. Las razones de por qué esto puede ser así, se discuten ampliamente en las conclusiones. Finalmente se puede precisar que dicha conclusión principal se refiere a viajes de una sola etapa (no multimodales) que se dan en los barrios y zonas del área metropolitana de Madrid. Por supuesto, esta conclusión tiene en la actualidad, una validez limitada, ya que es el resultado de un solo caso — Abstract The research hypothesis for this Ph.D. Thesis is that some characteristics of the built environment, particularly those describing the accessibility of the public space network, could be associated with the proportion of pedestrians in all trips (modal split), found in the different parts of a city. The underlying idea is that walking trips are more sensitive to built environment than those by other transport modes, such as for example those by bicycle or by public transport, which could be more conditioned by, e.g. infrastructure availability or service frequency and quality. On the other hand, it has to be noted that the previously research on this field, in particular within Space Syntax’s where this study can be referred, have tested similar hypothesis using pedestrian volumes as the dependent variable, but never against modal split. According to such hypothesis, research methodology is based primarily on empirical quantitative analysis, and it is meant to be able to assess whether public space network, no matter other built environment and non-built environment variables, could have a relationship with the proportion of pedestrian trips in urban areas. Statistical techniques are used to check the association of independent variables with the percentage of walking in all trips, the dependent one. Broadly speaking this methodology is similar to that of previous studies in the field such as CERVERO&KOCKLEMAN (1997), CERVERO & DUNCAN (2003), or to those used mainly in the general review of T.R.B. (2005) or, more recently in ZEGRAS (2006) or CHATMAN (2009). Other methodological options such as stated choice methods (see LOUVIERE, HENSHER & SWAIT, 2000) or agent based analysis (PENN & TURNER, 2004), were discarded, due to a number of reasons, too long to be described here. The case study is not the entire Madrid’s metropolitan area, but almost (4.132.820 inhabitants, about 80% of region´s population). Main data sources are the Regional Mobility Home Based Survey 2004 (EDM04), which is the last available (sample: >35.000 families, > 95.000 individuals), and a spatial model of the metropolitan area, developed using Space Syntax and G.I.S. techniques. The analysis unit, in this case spatial units, are both transport zones (mean population = 7.063) and neighborhoods (mean population = 26.466). The variables of the built environment are clearly the core of the study. A total of 20 (out of 21) are selected from among those found in the literature while, at the same time, being accessible. Nine out of them are used to describe land use characteristics while another eleven describe the network of public spaces. Latter ones include configurational accessibility or Space Syntax variables. This is a particular sort of accessibility related with the concept of configuration, by HILLIER (1996), one of the main authors of Space Syntax, But it also include more customary variables used in mobility research to describe the urban design or spatial structure (here public space network), which here are called geometric characteristics of the such as its length, type of intersection, conectivity, density, etc. Finally a single socioeconomic variable was included in order to assess the influence non built environment factors that also may have an impact on walking (age, income, motorization rate, etc.). The association among variables is worked out using bi-variate correlation analysis and multivariate-analysis. Correlations are calculated among the 21 independent variables and the dependent one, the percentage of walking trips. Then, three types of multi-variate studies are run: general linear, curvilinear and discriminant multi-variate analysis. The latter are fully capable of generating complex association models among several variables, assessing quite precisely to what extent each model reproduces the behavior of the dependent variable, and also the weight or influence of each variable in the model. This study’s results show a consistent influence of three particular indexes in the two final alternative models of the multi-variate study (best, R2=0,6789, p<0,0000). Not surprisingly, two of them correspond to density and mix of land uses. But perhaps more interesting is that the third one is a measure of the accessibility of the public space network, a variable less important in the literature up to now. Additional precisions about them and their relative weight could also be of some interest. The density index is not only about population but includes most important activities in an area (nº residents + nº jobs+ nº students/Ha). The configurational index (radius 5 integration) is a measure of the accessibility of the area, i.e. centrality, at the scale of, more a less, a district. Regarding the mix of land uses index, this one is a measure of the balance between retail, in fact local basic retail, and the number of residents (nº of convenience shops / nº of residents). Referring to their weights, configurational index (radius 5 integration) gets the higher standardized coefficient of the final equation. However, in the final equations, there are a higher number of indexes coming from the density or land use mix categories than from public space network enter. Therefore, these findings seem to support part of the field’s knowledge, especially those concerning land uses, but at the same time they seem to bring in the idea that the configuration of the urban grid could have an influence in the proportion of walkers (as a part of total trips on any transport mode) that do single journey trips in the neighborhoods of Madrid, Spain. Of course this conclusion has, at present, a limited validity since it’s the result of a single case. The reasons of why this can be so, are discussed in the last part of the thesis.

Discriminating Crop, Weeds and Soil Surface with a Terrestrial LIDAR Sensor

In this study, the evaluation of the accuracy and performance of a light detection and ranging (LIDAR) sensor for vegetation using distance and reflection measurements aiming to detect and discriminate maize plants and weeds from soil surface was done. The study continues a previous work carried out in a maize field in Spain with a LIDAR sensor using exclusively one index, the height profile. The current system uses a combination of the two mentioned indexes. The experiment was carried out in a maize field at growth stage 12–14, at 16 different locations selected to represent the widest possible density of three weeds: Echinochloa crus-galli (L.) P.Beauv., Lamium purpureum L., Galium aparine L.and Veronica persica Poir.. A terrestrial LIDAR sensor was mounted on a tripod pointing to the inter-row area, with its horizontal axis and the field of view pointing vertically downwards to the ground, scanning a vertical plane with the potential presence of vegetation. Immediately after the LIDAR data acquisition (distances and reflection measurements), actual heights of plants were estimated using an appropriate methodology. For that purpose, digital images were taken of each sampled area. Data showed a high correlation between LIDAR measured height and actual plant heights (R 2 = 0.75). Binary logistic regression between weed presence/absence and the sensor readings (LIDAR height and reflection values) was used to validate the accuracy of the sensor. This permitted the discrimination of vegetation from the ground with an accuracy of up to 95%. In addition, a Canonical Discrimination Analysis (CDA) was able to discriminate mostly between soil and vegetation and, to a far lesser extent, between crop and weeds. The studied methodology arises as a good system for weed detection, which in combination with other principles, such as vision-based technologies, could improve the efficiency and accuracy of herbicide spraying.

Instability Analysis of Incompressible Open Cavity Flows

El problema del flujo sobre una cavidad abierta ha sido estudiado en profundidad en la literatura, tanto por el interés académico del problema como por sus aplicaciones prácticas en gran variedad de problemas ingenieriles, como puede ser el alojamiento del tren de aterrizaje de aeronaves, o el depósito de agua de aviones contraincendios. Desde hace muchos a˜nos se estudian los distintos tipos de inestabilidades asociadas a este problema: los modos bidimensionales en la capa de cortadura, y los modos tridimensionales en el torbellino de recirculación principal dentro de la cavidad. En esta tesis se presenta un estudio paramétrico completo del límite incompresible del problema, empleando la herramienta de estabilidad lineal conocida como BiGlobal. Esta aproximación permite contemplar la estabilidad global del flujo, y obtener tanto la forma como las características de los modos propios del problema físico, sean estables o inestables. El estudio realizado permite caracterizar con gran detalle todos los modos relevantes, así como la envolvente de estabilidad en el espacio paramétrico del problema incompresible (Mach nulo, variación de Reynolds, espesor de capa límite incidente, relación altura/profundidad de la cavidad, y longitud característica de la perturbación en la dirección transversal). A la luz de los resultados obtenidos se proponen una serie de relaciones entre los parámetros y características de los modos principales, como por ejemplo entre el Reynolds crítico de un modo, y la longitud característica del mismo. Los resultados numéricos se contrastan con una campaña experimental, siendo la principal conclusión de dicha comparación que los modos lineales están presentes en el flujo real saturado, pero que existen diferencias notables en frecuencia entre las predicciones teóricas y los experimentos. Para intentar determinar la naturaleza de dichas diferencias se realiza una simulación numérica directa tridimensional, y se utiliza un algoritmo de DMD (descomposición dinámica de modos) para describir el proceso de saturación. ABSTRACT The problem of the flow over an open cavity has been studied in depth in the literature, both for being an interesting academical problem and due to the multitude of industrial applications, like the landing gear of aircraft, or the water deposit of firefighter airplanes. The different types of instabilities appearing in this flow studied in the literature are two: the two-dimensional shear layer modes, and the three-dimensional modes that appear in the main recirculating vortex inside the cavity. In this thesis a parametric study in the incompressible limit of the problem is presented, using the linear stability analysis known as BiGlobal. This approximation allows to obtain the global stability behaviour of the flow, and to capture both the morphological features and the characteristics of the eigenmodes of the physical problem, whether they are stable or unstable. The study presented here characterizes with great detail all the relevant eigenmodes, as well as the hypersurface of instability on the parameter space of the incompressible problem (Mach equal to zero, and variation of the Reynolds number, the incoming boundary layer thickness, the length to depth aspect ratio of the cavity and the spanwise length of the perturbation). The results allow to construct parametric relations between the characteristics of the leading eigenmodes and the parameters of the problem, like for example the one existing between the critical Reynolds number and its characteristic length. The numerical results presented here are compared with those of an experimental campaign, with the main conclusion of said comparison being that the linear eigenmode are present in the real saturated flow, albeit with some significant differences in the frequencies of the experiments and those predicted by the theory. To try to determine the nature of those differences a three-dimensional direct numerical simulation, analyzed with Dynamic Mode Decomposition algorithm, was used to describe the process of saturation.

A method to incorporate the effect of taxonomic uncertainty on multivariate analyses of ecological data

Researchers in ecology commonly use multivariate analyses (e.g. redundancy analysis, canonical correspondence analysis, Mantel correlation, multivariate analysis of variance) to interpret patterns in biological data and relate these patterns to environmental predictors. There has been, however, little recognition of the errors associated with biological data and the influence that these may have on predictions derived from ecological hypotheses. We present a permutational method that assesses the effects of taxonomic uncertainty on the multivariate analyses typically used in the analysis of ecological data. The procedure is based on iterative randomizations that randomly re-assign non identified species in each site to any of the other species found in the remaining sites. After each re-assignment of species identities, the multivariate method at stake is run and a parameter of interest is calculated. Consequently, one can estimate a range of plausible values for the parameter of interest under different scenarios of re-assigned species identities. We demonstrate the use of our approach in the calculation of two parameters with an example involving tropical tree species from western Amazonia: 1) the Mantel correlation between compositional similarity and environmental distances between pairs of sites, and; 2) the variance explained by environmental predictors in redundancy analysis (RDA). We also investigated the effects of increasing taxonomic uncertainty (i.e. number of unidentified species), and the taxonomic resolution at which morphospecies are determined (genus-resolution, family-resolution, or fully undetermined species) on the uncertainty range of these parameters. To achieve this, we performed simulations on a tree dataset from southern Mexico by randomly selecting a portion of the species contained in the dataset and classifying them as unidentified at each level of decreasing taxonomic resolution. An analysis of covariance showed that both taxonomic uncertainty and resolution significantly influence the uncertainty range of the resulting parameters. Increasing taxonomic uncertainty expands our uncertainty of the parameters estimated both in the Mantel test and RDA. The effects of increasing taxonomic resolution, however, are not as evident. The method presented in this study improves the traditional approaches to study compositional change in ecological communities by accounting for some of the uncertainty inherent to biological data. We hope that this approach can be routinely used to estimate any parameter of interest obtained from compositional data tables when faced with taxonomic uncertainty.

Modelling the Impact of Built Environment, Geographical Scales and Latent Constructs On Individual Travel Behaviour

La relación entre la estructura urbana y la movilidad ha sido estudiada desde hace más de 70 años. El entorno urbano incluye múltiples dimensiones como por ejemplo: la estructura urbana, los usos de suelo, la distribución de instalaciones diversas (comercios, escuelas y zonas de restauración, parking, etc.). Al realizar una revisión de la literatura existente en este contexto, se encuentran distintos análisis, metodologías, escalas geográficas y dimensiones, tanto de la movilidad como de la estructura urbana. En este sentido, se trata de una relación muy estudiada pero muy compleja, sobre la que no existe hasta el momento un consenso sobre qué dimensión del entorno urbano influye sobre qué dimensión de la movilidad, y cuál es la manera apropiada de representar esta relación. Con el propósito de contestar estas preguntas investigación, la presente tesis tiene los siguientes objetivos generales: (1) Contribuir al mejor entendimiento de la compleja relación estructura urbana y movilidad. y (2) Entender el rol de los atributos latentes en la relación entorno urbano y movilidad. El objetivo específico de la tesis es analizar la influencia del entorno urbano sobre dos dimensiones de la movilidad: número de viajes y tipo de tour. Vista la complejidad de la relación entorno urbano y movilidad, se pretende contribuir al mejor entendimiento de la relación a través de la utilización de 3 escalas geográficas de las variables y del análisis de la influencia de efectos inobservados en la movilidad. Para el análisis se utiliza una base de datos conformada por tres tipos de datos: (1) Una encuesta de movilidad realizada durante los años 2006 y 2007. Se obtuvo un total de 943 encuestas, en 3 barrios de Madrid: Chamberí, Pozuelo y Algete. (2) Información municipal del Instituto Nacional de Estadística: dicha información se encuentra enlazada con los orígenes y destinos de los viajes recogidos en la encuesta. Y (3) Información georeferenciada en Arc-GIS de los hogares participantes en la encuesta: la base de datos contiene información respecto a la estructura de las calles, localización de escuelas, parking, centros médicos y lugares de restauración. Se analizó la correlación entre e intra-grupos y se modelizaron 4 casos de atributos bajo la estructura ordinal logit. Posteriormente se evalúa la auto-selección a través de la estimación conjunta de las elecciones de tipo de barrio y número de viajes. La elección del tipo de barrio consta de 3 alternativas: CBD, Urban y Suburban, según la zona de residencia recogida en las encuestas. Mientras que la elección del número de viajes consta de 4 categorías ordinales: 0 viajes, 1-2 viajes, 3-4 viajes y 5 o más viajes. A partir de la mejor especificación del modelo ordinal logit. Se desarrolló un modelo joint mixed-ordinal conjunto. Los resultados indican que las variables exógenas requieren un análisis exhaustivo de correlaciones con el fin de evitar resultados sesgados. ha determinado que es importante medir los atributos del BE donde se realiza el viaje, pero también la información municipal es muy explicativa de la movilidad individual. Por tanto, la percepción de las zonas de destino a nivel municipal es considerada importante. En el contexto de la Auto-selección (self-selection) es importante modelizar conjuntamente las decisiones. La Auto-selección existe, puesto que los parámetros estimados conjuntamente son significativos. Sin embargo, sólo ciertos atributos del entorno urbano son igualmente importantes sobre la elección de la zona de residencia y frecuencia de viajes. Para analizar la Propensión al Viaje, se desarrolló un modelo híbrido, formado por: una variable latente, un indicador y un modelo de elección discreta. La variable latente se denomina “Propensión al Viaje”, cuyo indicador en ecuación de medida es el número de viajes; la elección discreta es el tipo de tour. El modelo de elección consiste en 5 alternativas, según la jerarquía de actividades establecida en la tesis: HOME, no realiza viajes durante el día de estudio, HWH tour cuya actividad principal es el trabajo o estudios, y no se realizan paradas intermedias; HWHs tour si el individuo reaiza paradas intermedias; HOH tour cuya actividad principal es distinta a trabajo y estudios, y no se realizan paradas intermedias; HOHs donde se realizan paradas intermedias. Para llegar a la mejor especificación del modelo, se realizó un trabajo importante considerando diferentes estructuras de modelos y tres tipos de estimaciones. De tal manera, se obtuvieron parámetros consistentes y eficientes. Los resultados muestran que la modelización de los tours, representa una ventaja sobre la modelización de los viajes, puesto que supera las limitaciones de espacio y tiempo, enlazando los viajes realizados por la misma persona en el día de estudio. La propensión al viaje (PT) existe y es específica para cada tipo de tour. Los parámetros estimados en el modelo híbrido resultaron significativos y distintos para cada alternativa de tipo de tour. Por último, en la tesis se verifica que los modelos híbridos representan una mejora sobre los modelos tradicionales de elección discreta, dando como resultado parámetros consistentes y más robustos. En cuanto a políticas de transporte, se ha demostrado que los atributos del entorno urbano son más importantes que los LOS (Level of Service) en la generación de tours multi-etapas. la presente tesis representa el primer análisis empírico de la relación entre los tipos de tours y la propensión al viaje. El concepto Propensity to Travel ha sido desarrollado exclusivamente para la tesis. Igualmente, el desarrollo de un modelo conjunto RC-Number of trips basado en tres escalas de medida representa innovación en cuanto a la comparación de las escalas geográficas, que no había sido hecha en la modelización de la self-selection. The relationship between built environment (BE) and travel behaviour (TB) has been studied in a number of cases, using several methods - aggregate and disaggregate approaches - and different focuses – trip frequency, automobile use, and vehicle miles travelled and so on. Definitely, travel is generated by the need to undertake activities and obtain services, and there is a general consensus that urban components affect TB. However researches are still needed to better understand which components of the travel behaviour are affected most and by which of the urban components. In order to fill the gap in the research, the present dissertation faced two main objectives: (1) To contribute to the better understanding of the relationship between travel demand and urban environment. And (2) To develop an econometric model for estimating travel demand with urban environment attributes. With this purpose, the present thesis faced an exhaustive research and computation of land-use variables in order to find the best representation of BE for modelling trip frequency. In particular two empirical analyses are carried out: 1. Estimation of three dimensions of travel demand using dimensions of urban environment. We compare different travel dimensions and geographical scales, and we measure self-selection contribution following the joint models. 2. Develop a hybrid model, integrated latent variable and discrete choice model. The implementation of hybrid models is new in the analysis of land-use and travel behaviour. BE and TB explicitly interact and allow richness information about a specific individual decision process For all empirical analysis is used a data-base from a survey conducted in 2006 and 2007 in Madrid. Spatial attributes describing neighbourhood environment are derived from different data sources: National Institute of Statistics-INE (Administrative: municipality and district) and GIS (circular units). INE provides raw data for such spatial units as: municipality and district. The construction of census units is trivial as the census bureau provides tables that readily define districts and municipalities. The construction of circular units requires us to determine the radius and associate the spatial information to our households. The first empirical part analyzes trip frequency by applying an ordered logit model. In this part is studied the effect of socio-economic, transport and land use characteristics on two travel dimensions: trip frequency and type of tour. In particular the land use is defined in terms of type of neighbourhoods and types of dwellers. Three neighbourhood representations are explored, and described three for constructing neighbourhood attributes. In particular administrative units are examined to represent neighbourhood and circular – unit representation. Ordered logit models are applied, while ordinal logit models are well-known, an intensive work for constructing a spatial attributes was carried out. On the other hand, the second empirical analysis consists of the development of an innovative econometric model that considers a latent variable called “propensity to travel”, and choice model is the choice of type of tour. The first two specifications of ordinal models help to estimate this latent variable. The latent variable is unobserved but the manifestation is called “indicators”, then the probability of choosing an alternative of tour is conditional to the probability of latent variable and type of tour. Since latent variable is unknown we fit the integral over its distribution. Four “sets of best variables” are specified, following the specification obtained from the correlation analysis. The results evidence that the relative importance of SE variables versus BE variables depends on how BE variables are measured. We found that each of these three spatial scales has its intangible qualities and drawbacks. Spatial scales play an important role on predicting travel demand due to the variability in measures at trip origin/destinations within the same administrative unit (municipality, district and so on). Larger units will produce less variation in data; but it does not affect certain variables, such as public transport supply, that are more significant at municipality level. By contrast, land-use measures are more efficient at district level. Self-selection in this context, is weak. Thus, the influence of BE attributes is true. The results of the hybrid model show that unobserved factors affect the choice of tour complexity. The latent variable used in this model is propensity to travel that is explained by socioeconomic aspects and neighbourhood attributes. The results show that neighbourhood attributes have indeed a significant impact on the choice of the type of tours either directly and through the propensity to travel. The propensity to travel has a different impact depending on the structure of each tour and increases the probability of choosing more complex tours, such as tours with many intermediate stops. The integration of choice and latent variable model shows that omitting important perception and attitudes leads to inconsistent estimates. The results also indicate that goodness of fit improves by adding the latent variable in both sequential and simultaneous estimation. There are significant differences in the sensitivity to the latent variable across alternatives. In general, as expected, the hybrid models show a major improvement into the goodness of fit of the model, compared to a classical discrete choice model that does not incorporate latent effects. The integrated model leads to a more detailed analysis of the behavioural process. Summarizing, the effect that built environment characteristics on trip frequency studied is deeply analyzed. In particular we tried to better understand how land use characteristics can be defined and measured and which of these measures do have really an impact on trip frequency. We also tried to test the superiority of HCM on this field. We can concluded that HCM shows a major improvement into the goodness of fit of the model, compared to classical discrete choice model that does not incorporate latent effects. And consequently, the application of HCM shows the importance of LV on the decision of tour complexity. People are more elastic to built environment attributes than level of services. Thus, policy implications must take place to develop more mixed areas, work-places in combination with commercial retails.

Molecular analysis of endo-β-mannanase genes upon seed imbibition suggest a cross-talk between radicle and micropylar endosperm during germination of Arabidopsis thaliana.

The endo-β-mannanase (MAN) family is represented in the Arabidopsis genome by eight members, all with canonical signal peptides and only half of them being expressed in germinating seeds. The transcripts of these genes were localized in the radicle and micropylar endosperm (ME) before radicle protrusion and this expression disappears as soon as the endosperm is broken by the emerging radicle tip. However, only three of these MAN genes, AtMAN5, AtMAN7 and especially AtMAN6 influence the germination time (t50) as assessed by the analysis of the corresponding knock-out lines. The data suggest a possible interaction between embryo and ME regarding the role of MAN during the Arabidopsis germination process.

Projector Model for Efficient List-Mode Reconstruction in PET Scanners with Parallel Planar Detectors

We have developed a new projector model specifically tailored for fast list-mode tomographic reconstructions in Positron emission tomography (PET) scanners with parallel planar detectors. The model provides an accurate estimation of the probability distribution of coincidence events defined by pairs of scintillating crystals. This distribution is parameterized with 2D elliptical Gaussian functions defined in planes perpendicular to the main axis of the tube of response (TOR). The parameters of these Gaussian functions have been obtained by fitting Monte Carlo simulations that include positron range, acolinearity of gamma rays, as well as detector attenuation and scatter effects. The proposed model has been applied efficiently to list-mode reconstruction algorithms. Evaluation with Monte Carlo simulations over a rotating high resolution PET scanner indicates that this model allows to obtain better recovery to noise ratio in OSEM (ordered-subsets, expectation-maximization) reconstruction, if compared to list-mode reconstruction with symmetric circular Gaussian TOR model, and histogram-based OSEM with precalculated system matrix using Monte Carlo simulated models and symmetries.

Four Decades of Studying Global Linear Instability: Progress and Challenges

Global linear instability theory is concerned with the temporal or spatial development of small-amplitude perturbations superposed upon laminar steady or time-periodic three-dimensional flows, which are inhomogeneous in two(and periodic in one)or all three spatial directions.After a brief exposition of the theory,some recent advances are reported. First, results are presented on the implementation of a Jacobian-free Newton–Krylov time-stepping method into a standard finite-volume aerodynamic code to obtain global linear instability results in flows of industrial interest. Second, connections are sought between established and more-modern approaches for structure identification in flows, such as proper orthogonal decomposition and Koopman modes analysis (dynamic mode decomposition), and the possibility to connect solutions of the eigenvalue problem obtained by matrix formation or time-stepping with those delivered by dynamic mode decomposition, residual algorithm, and proper orthogonal decomposition analysis is highlighted in the laminar regime; turbulent and three-dimensional flows are identified as open areas for future research. Finally, a new stable very-high-order finite-difference method is implemented for the spatial discretization of the operators describing the spatial biglobal eigenvalue problem, parabolized stability equation three-dimensional analysis, and the triglobal eigenvalue problem; it is shown that, combined with sparse matrix treatment, all these problems may now be solved on standard desktop computers

Analysis of the discharge capacity of radial-gated spillways using CFD and ANN - Oliana Dam case study.

The paper focuses on the analysis of radial-gated spillways, which is carried out by the solution of a numerical model based on the finite element method (FEM). The Oliana Dam is considered as a case study and the discharge capacity is predicted both by the application of a level-set-based free-surface solver and by the use of traditional empirical formulations. The results of the analysis are then used for training an artificial neural network to allow real-time predictions of the discharge in any situation of energy head and gate opening within the operation range of the reservoir. The comparison of the results obtained with the different methods shows that numerical models such as the FEM can be useful as a predictive tool for the analysis of the hydraulic performance of radial-gated spillways.