The introduction of teaching innovations into the traditional teaching of construction and building materials

The traditional teaching methods used for training civil engineers are currently being called into question as a result of the new knowledge and skills now required by the labor market. In addition, the European Higher Education Area is requesting that students be given a greater say in their learning. In the subject called Construction and Building Materials at the Civil Engineering School of the Universidad Politécnica de Madrid, a path was set three academic years ago to lead to an improvement in traditional teaching by introducing active methodologies. The innovations are based on cooperative learning, new technologies, and continuous assessment. The writers’ proposal is to offer their experience as a contribution to the debate on how students can be encouraged to acquire the skills currently demanded from a civil engineer, though not overlooking solid, top-quality training. From the outcomes obtained, it can be concluded that using new teaching techniques to supplement a traditional approach provides more opportunities for students to learn while boosting their motivation. In our case, the introduction of these changes has resulted in an increased pass rate of 29% on average, when such a figure is considered in the light of the mean value of passes during the last decade.

A Development Methodology to Facilitate the Integration of Smart Spaces into the Web of Things

How to create or integrate large Smart Spaces (considered as mash-ups of sensors and actuators) into the paradigm of ?Web of Things? has been the motivation of many recent works. A cutting-edge approach deals with developing and deploying web-enabled embedded devices with two major objectives: 1) to integrate sensor and actuator technologies into everyday objects, and 2) to allow a diversity of devices to plug to Internet. Currently, developers who want to use this Internet-oriented approach need have solid understanding about sensorial platforms and semantic technologies. In this paper we propose a Resource-Oriented and Ontology-Driven Development (ROOD) methodology, based on Model Driven Architecture (MDA), to facilitate to any developer the development and deployment of Smart Spaces. Early evaluations of the ROOD methodology have been successfully accomplished through a partial deployment of a Smart Hotel.

Gas monitoring methodology and application to CCS projects as defined by atmospheric and remote sensing survey in the natural analogue of Campo de Calatrava

CO2 capture and storage (CCS) projects are presently developed to reduce the emission of anthropogenic CO2 into the atmosphere. CCS technologies are expected to account for the 20% of the CO2 reduction by 2050. Geophysical, ground deformation and geochemical monitoring have been carried out to detect potential leakage, and, in the event that this occurs, identify and quantify it. This monitoring needs to be developed prior, during and after the injection stage. For a correct interpretation and quantification of the leakage, it is essential to establish a pre-injection characterization (baseline) of the area affected by the CO2 storage at reservoir level as well as at shallow depth, surface and atmosphere, via soil gas measurements. Therefore, the methodological approach is important because it can affect the spatial and temporal variability of this flux and even jeopardize the total value of CO2 in a given area. In this sense, measurements of CO2 flux were done using portable infrared analyzers (i.e., accumulation chambers) adapted to monitoring the geological storage of CO2, and other measurements of trace gases, e.g. radon isotopes and remote sensing imagery were tested in the natural analogue of Campo de Calatrava (Ciudad Real, Spain) with the aim to apply in CO2 leakage detection; thus, observing a high correlation between CO2 and radon (r=0,858) and detecting some vegetation indices that may be successfully applied for the leakage detection.

Thermal behaviour of bitumen modified by sulphur addition

The most frequent use of bitumen is as binder for pavement applications. The effect of sulphur addition on the properties of the bitumen has been extensively studied several decades ago. Recently, there is a renewed interest in researching the behaviour of sulphur-bitumen combination, because off 1.The future availability of bitumen may be limited and 2. The beneficial consumption of great amounts of sulphur compounds from petroleum refining is advisable. The addition of sulphur to bitumen provokes the beginning of chemical reactions depending on the sulphur content and heating temperature. At heating temperatures T< 140 ºC liquid sulphur reacts with naphthenic-aromatic fraction forming polysulphides. At temperatures above 150 ºC dehydrogenization reactions with emission of hydrogen sulfide take place and naphthenic-aromatic molecules are transformed into asphaltenes. Therefore, the addition of sulphur to bitumen provokes changes in the chemical structure of the bitumen. The objective of this work is to analyze, the thermal behaviour of sulphur-bitumen mixtures of different composition (0-35 %wt sulphur content) prepared at 130 and 140 ºC, by means of differential scanning calorimetry (DSC). Besides, the volatile emissions of the mixtures at high temperature have been estimated from loss weight measurements as a function of stored time

Modelling Saharan dust transport into the Mediterranean basin with CMAQ

The need for a better quantification of the influence of Saharan dust transport processes on the air quality modelling in the Mediterranean basin led to the formulation of a dust emission module (DEM) integrated into the Air Quality Risk Assessment System for the Iberian Peninsula (SERCA). This paper is focused on the formulation of DEM based on the GOCART aerosol model, along with its integration and execution into the air quality model. It also addresses the testing of the module and its evaluation by contrasting results against satellite products such as MODIS and CALIPSO and ground-level observations of aerosol optical thickness (AOT) and concentration levels of PM10 for different periods in July 2007. DEM was found capable of reproducing the spatial (horizontal and vertical) and temporal profiles of Saharan dust outbreaks into the Mediterranean basin and the Atlantic coast of Africa. Moreover, it was observed that its combination with CMAQ increased the correlation degree between observed and modelled PM10 concentrations at the selected monitoring locations. DEM also enhanced CMAQ capabilities to reproduce observed AOT, although significant underestimations remain. The implementation of CMAQ + DEM succeeded in capturing Saharan dust transport into the Iberian Peninsula, with contributions up to 25 and 14 μg m−3 in 1 h and 24 h average PM10 respectively. The general improvement of total PM10 predictions in Spain are however moderate. The analysis of model performance for the main PM components points out that remaining PM10 underestimation is due to dust local sources missing in the inventories and misrepresentation of organic aerosol processes, which constitutes the main areas for future improvement of CMAQ capabilities to simulate particulate matter within SERCA.

Atmospheric and remote sensing surveys evaluated at the natural analogue "Campo de Calatrava" and its relation with isotopic Radon activity and CO2 flux as strategy for CCS projects

C0 capture and storage (CCS) projects are presently developed to reduce the emission of anthropogenic co2 into the atmosphere. CCS technologies are expected to account for the 20% of the C0 reduction by 2050.The results of this paper are referred to the OXYCFB300 Compostilla Project (European Energy Program for Recover). Since the detection and control of potential leakage from storage formation is mandatory in a project of capture and geological storage of C02 (CCS), geophysical , ground deformation and geochemical monitoring have been carried out to detect potentialleakage, and, in the event that this occurs, identify and quantify it. This monitoring needs to be developed prior, during and after the injection stage. For a correct interpretation and quantification of the leakage, it is essential to establish a pre-injection characterization (baseline)of the area affected by the C02 storage at reservoir level as well as at shallow depth, surface and atmosphere, via soil gas measurements.

Effect of level of fiber of the rearing phase diets on egg production, digestive tract traits, and body measurements of brown egg-laying hens fed diets differing in energy concentration

This research studied the effects of additional fiber in the rearing phase diets on egg production, gastrointestinal tract (GIT) traits, and body measurements of brown egg-laying hens fed diets varying in energy concentration from 17 to 46 wk of age. The experiment was completely randomized with 10 treatments arranged as a 5 × 2 factorial with 5 rearing phase diets and 2 laying phase diets. During the rearing phase, treatments consisted of a control diet based on cereals and soybean meal and 4 additional diets with a combination of 2 fiber sources (cereal straw and sugar beet pulp, SBP) at 2 levels (2 and 4%). During the laying phase, diets differed in energy content (2,650 vs. 2,750 kcal AMEn/kg) but had the same amino acid content per unit of energy. The rearing diet did not affect any production trait except egg production that was lower in birds fed SBP than in birds fed straw (91.6 and 94.1%, respectively; P < 0.05). Laying hens fed the high energy diet had lower feed intake (P < 0.001), better feed conversion (P < 0.01), and greater BW gain (P < 0.05) than hens fed the low energy diet but egg production and egg weight were not affected. At 46 wk of age, none of the GIT traits was affected by previous dietary treatment. At this age, hen BW was positively related with body length (r = 0.500; P < 0.01), tarsus length (r = 0.758; P < 0.001), and body mass index (r = 0.762; P < 0.001) but no effects of type of diet on these traits were detected. In summary, the inclusion of up to 4% of a fiber source in the rearing diets did not affect GIT development of the hens but SBP reduced egg production. An increase in the energy content of the laying phase diet reduced ADFI and improved feed efficiency but did not affect any of the other traits studied.

Geochemical monitoring in the Hontomín (Burgos, Spain) injection site: preliminary results and perspectives

CO2 capture and storage (CCS) projects are presently developed to reduce the emission of anthropogenic CO2 into the atmosphere. CCS technologies are expected to account for the 20% of the CO2 reduction by 2050. One of the main concerns of CCS is whether CO2 may remain confined within the geological formation into which it is injected since post-injection CO2 migration in the time scale of years, decades and centuries is not well understood. Theoretically, CO2 can be retained at depth i) as a supercritical fluid (physical trapping), ii) as a fluid slowly migrating in an aquifer due to long flow path (hydrodynamic trapping), iii) dissolved into ground waters (solubility trapping) and iv) precipitated secondary carbonates. Carbon dioxide will be injected in the near future (2012) at Hontomín (Burgos, Spain) in the frame of the Compostilla EEPR project, led by the Fundación Ciudad de la Energía (CIUDEN). In order to detect leakage in the operational stage, a pre-injection geochemical baseline is presently being developed. In this work a geochemical monitoring design is presented to provide information about the feasibility of CO2 storage at depth.

Estudio microestructural y de los procesos de hidratación de cementos con adiciones

En los últimos años, las sociedades industrializadas han tomado una mayor conciencia sobre el problema que suponen las emisiones indiscriminadas de gases de efecto invernadero a la atmósfera. El hormigón, cuyo principal componente es el cemento, es probablemente el material más utilizado en construcción. En la actualidad, las emisiones globales de CO2 debidas a la combustión del CaCO3 del cemento Pórtland representan entre el 5% y el 10% respecto del total. Estos valores son de gran interés si se considera que el compromiso aceptado al firmar el Protocolo de Kioto es de una reducción del 5% antes del año 2020, sobre el total de gases producidos. El principal objetivo del presente trabajo es el estudio microestructural y de los procesos de hidratación de los cementos con adiciones. Para ello se propone contribuir a la investigación sobre nuevos productos cementicios basados en micropartículas esféricas vítreas que pueden adicionarse al cemento antes del proceso de amasado. Los resultados obtenidos se han contrastado con las adiciones convencionales de más uso en la actualidad. El nuevo material basa su composición en la química del aluminio y el silicio. Al disminuir la cantidad de CaCO3, se contribuye al desarrollo sostenible y a la reducción de emisiones de CO2. La patente creada por el Grupo Cementos Pórtland Valderrivas (GCPV), describe el proceso de producción de las cemesferas (WO 2009/007470, 2010). Los productos que forman la materia prima para la elaboración de las cemesferas son arcillas, calizas, margas o productos o subproductos industriales, que tras su molienda, son fundidos mediante un fluido gaseoso a elevada temperatura (entre 1250ºC y 1600ºC). Este proceso permite obtener un producto final en forma esférica maciza o microesfera, que tras estabilizarse mediante un enfriamiento rápido, consigue una alta vitrificación idónea para su reactividad química, con una mínima superficie específica en relación a su masa. El producto final obtenido presenta prácticamente la finura requerida y no precisa ser molido, lo que reduce las emisiones de CO2 por el ahorro de combustible durante el proceso de molienda. El proceso descrito permite obtener un amplio abanico de materiales cementantes que, no solo pueden dar respuesta a los problemas generados por las emisiones de CO2, sino también a la disponibilidad de materiales en países donde hasta el momento no se puede fabricar cemento debido a la falta de calizas. Complementariamente se ha optimizado el método de cálculo del grado de hidratación a partir de los resultados del ensayo de ATD-TG en base a los modelos de cálculo de Bhatty y Pane. El método propuesto permite interpretar el comportamiento futuro del material a partir de la interpolación numérica de la cantidad de agua químicamente enlazada. La evolución del grado de hidratación tiene una relación directa con el desarrollo de la resistencia mecánica del material. Con el fin de caracterizar los materiales de base cemento, se ha llevado a cabo una amplia campaña experimental en pasta de cemento, mortero y hormigón. La investigación abarca tres niveles: caracterización microestructural, macroestructural y caracterización del comportamiento a largo plazo, fundamentalmente durabilidad. En total se han evaluado ocho adiciones diferentes: cuatro adiciones convencionales y cuatro tipos de cemesferas con diferente composición química. Los ensayos a escala microscópica comprenden la caracterización química, granulométrica y de la superficie específica BET de los materiales anhidros, análisis térmico diferencial y termogravimétrico en pasta de cemento y mortero, resonancia magnética de silicio en pasta de cemento, difracción de rayos X de los materiales anhidros y de las probetas de pasta, microscopía electrónica de barrido con analizador de energía dispersiva por rayos X en pasta y mortero, y porosimetría por intrusión de mercurio en mortero. La caracterización macroscópica del material comprende ensayos de determinación del agua de consistencia normal y de los tiempos de inicio y fin de fraguado en pasta de cemento, ensayos de resistencia mecánica a flexión y compresión en probetas prismáticas de mortero, y ensayos de resistencia a compresión en probetas de hormigón. Para caracterizar la durabilidad se han desarrollado ensayos de determinación del coeficiente de migración de cloruros y ensayos de resistividad eléctrica en probetas de mortero. Todos los ensayos enumerados permiten clarificar el comportamiento de las cemesferas y compararlo con las distintas adiciones de uso convencional. Los resultados reflejan un buen comportamiento resistente y durable de los materiales con adición de cemesferas. La caracterización microscópica refleja su relación con las propiedades mesoscópicas y permite comprender mejor la evolución en los procesos de hidratación de las cemesferas. In recent years industrialised societies have become increasingly aware of the problem posed by indiscriminate emission of greenhouse gases into the atmosphere. Concrete, with a main component being cement, is arguably the most widely used construction material. At present, global emissions of CO2 due to the combustion of CaCO3 from Portland cement represent between 5% and 10% of the total. If the requirement of the Kyoto Protocol of a reduction of 5% of the total gas produced before 2020 is considered, then such values are of significant interest. The main objective of this work is the assessment of the microstructure and the hydration processes of cements with additions. Such an examination proposes research into new cementitious products based on vitreous spherical microparticles that may be added to the cement before the mixing process. The results are compared with the most commonly used conventional additions. The new material bases its composition on the chemistry of aluminium and silicates. By decreasing the amount of CaCO3, it is possible both to contribute to sustainable development and reduce CO2 emissions. The patent created by Grupo Cementos Portland Valderrivas (GCPV) describes the production process of microspheres (WO 2009/007470, 2010). The products that form the raw material for manufacture are clays, lime-stone, marl and industrial products or by-products that melt after being ground and fed into a gaseous fluid at high temperatures (1250°C and 1600°C). This process allows the obtaining of a product with a solid-spherical or micro-spherical shape and which, after being stabilised in a solid state by rapid cooling, obtains a high vitrification suitable for chemical reactivity, having a minimal surface in relation to its mass. Given that the final product has the fineness required, it prevents grinding that reduces CO2 emissions by saving fuel during this process. The process, which allows a wide range of cementitious materials to be obtained, not only addresses the problems caused by CO2 emissions but also enhances the availability of materials in countries that until the time of writing have not produced cement due to a lack of limestone. In addition, the calculation of the degree of hydration from the test results of DTA-TG is optimised and based on Bhatty and Pane calculation models. The proposed method allows prediction of the performance of the material from numerical interpolation of the amount of chemically bound water. The degree of hydration has a direct relationship with the development of material mechanical strength. In order to characterise the cement-based materials, an extensive experimental campaign in cement paste, concrete and mortar is conducted. The research comprises three levels: micro-structural characterisation, macro-structural and long-term behaviour (mainly durability). In total, eight additions are assessed: four conventional additions and four types of microspheres with different chemical compositions. The micro-scale tests include characterisation of chemical composition, particle size distribution and the BET specific surface area of anhydrous material, differential thermal and thermogravimetric analysis in cement paste and mortar, silicon-29 nuclear magnetic resonance in cement paste, X-ray diffraction of the anhydrous materials and paste specimens, scanning of electron microscopy with energy dispersive X-ray analyser in cement paste and mortar, and mercury intrusion porosimetry in mortar. The macroscopic material characterisation entails determination of water demand for normal consistency, and initial and final setting times of cement paste, flexural and compressive mechanical strength tests in prismatic mortar specimens, and compressive strength tests in concrete specimens. Tests for determining the chloride migration coefficient are performed to characterise durability, together with electrical resistivity tests in mortar specimens. All the tests listed allow clarification of the behaviour of the microspheres and comparison with the various additions of conventional use. The results show good resistance and durable behaviour of materials with a microsphere addition. Microscopic characterisation reflects their relationship with mesoscopic properties and provides insights into the hydration processes of the microspheres.

Repercusión medioambiental del uso de la cerámica estructural en España. Energía embebida y huella de carbono

La producción y el transporte a obra de los productos cerámicos de carácter estructural suponen un importante consumo energético, que conlleva la emisión de gases de efecto invernadero a la atmósfera. El objetivo de la presente Tesis es demostrar la existencia de importantes diferencias en el valor del impacto ambiental asociado a los productos de cerámica estructural fabricados en España, y que estas diferencias podrían quedar cuantificadas y reflejadas mediante un análisis de Huella de Carbono y de la Energía Embebida. Se parte de la inexistencia en España, de base de datos contrastada y consensuada, que establezca las cargas medioambientales en función del tipo de producto cerámico a utilizar. Se realiza en la primera parte del estudio una revisión del estado actual de la Huella de Carbono y la Energía Embebida en el campo de los materiales de construcción, y más concretamente en el sector de la cerámica estructural, que sirve para acotar los límites del estudio y justificar el objeto de la Tesis. La investigación se acota a las etapas de producción y transporte a obra de los productos (estudio cuna a puerta con opciones), al considerar que son éstas, a priori, las que tienen una mayor incidencia en el comportamiento ambiental del producto. Siguiendo los pasos definidos en la normativa aplicable (definición del mapa de procesos – límites y alcance – inventario – cálculo y evaluación), se establece un método específico de identificación y cuantificación de las variables que determinan la Huella de Carbono y Energía Embebida de los productos cerámicos, en función de la tipología de producto. La información necesaria (inventario) se obtiene principalmente con recogida de datos “in situ” de fábricas de productos cerámicos, lo que garantiza que la información tratada en este estudio es de primer nivel. La información se complementa/contrasta con fuentes bibliográficas. Se determinan 6 variables con influencia global en el impacto ambiental, 44 variables principales y 39 secundarias, estableciendo las fórmulas de cálculo a partir de dichas variables. Los resultados de cálculo y evaluación determinan que, para unas mismas condiciones de fabricación, las diferencias entre productos cerámicos llegan hasta un 27% para la Huella de Carbono y un 35% para Energía Embebida. La relevancia que alcanza el impacto asociado al transporte del producto a obra puede llegar hasta un 40% del total. El método de cálculo y las fórmulas desarrolladas se integran en una hoja de cálculo, para el cálculo de Huella de Carbono y Energía Embebida de los productos cerámicos, que permite, a su vez, conocer la repercusión medioambiental que tiene la introducción de modificaciones o innovaciones en el proceso de producción o transporte a obra. Así mismo, el trabajo desarrollado ha servido para poner en relieve una serie de problemas y falta de información en el campo de la cerámica estructural y el medioambiente que pueden ser objeto de futuras líneas de investigación, tanto para el sector de la edificación como para la comunidad científica, pudiendo implementar la metodología desarrollada en otras investigaciones. Se considera que la investigación realizada y sus resultados suponen una aportación importante para conocer y reducir el impacto ambiental de los edificios, desde la perspectiva del ciclo de vida y considerando que el impacto ambiental de un edificio comienza desde el momento en que se extraen las materias primas para la fabricación de los materiales con los que se construyen los edificios. ABSTRACT The production and transport of structural ceramic products involves an important energy consumption, which leads to the emission of greenhouse gases into the atmosphere. The objective of the research is to demonstrate the existence of significant differences in the value of the environmental impact of structural ceramic products manufactured in Spain, and these differences could be quantified by the Carbon Footprint and Embodied Energy. It starts from the absence in Spain, of contrasted and agreed databases that establish the environmental loads depending on the type of ceramic product. In the first part of the study reviews the current state of the Carbon Footprint and Embedded Energy in the field of building materials, and more specifically in the field of structural ceramics, which serves to limit the scope of the study and justify the purpose of this Thesis. The Research is bounded to production and transportation stages of (cradle to gate with options), considering they are the stages that have a greater impact on the environmental performance of the product. Following the steps defined in applicable rules (definition of process map - boundaries and scope – inventory analysis- calculation and impact assessment), it sets a specific method for the identification and quantification of the variables that determine the Carbon Footprint and Embedded Energy of structural ceramic products, depending on the type of product. The information (inventory) is given mainly with a data collection in ceramic factories (and in a consultation with the manufactures of the products), ensuring that the information handled in this Thesis is a first rate data. It is established 6 variables with a global influence in the environmental impact, 44 primary and 39 secondary variables, establishing calculation formula from these variables. The results of calculation and assessment determined that, for same manufacturing conditions, the differences between ceramic products reach 27% for Carbon Footprint and 35% for Embodied Energy. The relevance that reaches the impact of transport can reach 40% of the total. The method of calculation and formulas developed are integrated into a simple calculation tool, excel base, to calculate the Carbon Footprint and Embodied Energy of structural ceramic products, which allows, know the environmental impact of changes or innovations in the production process or transport to work. The work also has served to find a problems and gaps in the field of structural ceramics and the environment that may well be the subject of future research, both for the building sector to the scientific community, implementing the methodology developed in other research. It is considered that the research and its results represent an important contribution to understand and reduce the environmental impact of buildings from the perspective of the life cycle, considering that the environmental impact of a building starts from the time that the raw materials are extracted for the manufacture of building materials.

Multi-scale study of hydrogen isotopes structural properties in solid phase in the context of inertial fusion target manufacturing

Designing the ignition and high-gain targets for inertial confinement fusion (ICF) requires a condensed uniform layer of the hydrogen fuel on the inner surface of a spherical polymer shell. The fuel layers have to be highly uniform in thickness and roughness.