Low-Profile Dual Circularly Polarized Antenna Array for Satellite Communications in the X Band

A planar antenna is introduced that works as a portable system for X-band satellite communications. This antenna is low-profile and modular with dimensions of 40 × 40 × 2.5 × cm. It is composed of a square array of 144 printed circuit elements that cover a wide bandwidth (14.7%) for transmission and reception along with dual and interchangeable circular polarization. A radiation efficiency above 50% is achieved by a low-loss stripline feeding network. This printed antenna has a 3 dB beamwidth of 5°, a maximum gain of 26 dBi and an axial ratio under 1.9 dB over the entire frequency band. The complete design of the antenna is shown, and the measurements are compared with simulations to reveal very good agreement.

Dual circular polarized steering antenna for satellite communications in X band

In this work, a dual circular polarized steering antenna for satellite communications in X band is presented. The antenna consists of printed elements grouped in an array. This terminal works in a frequency band from 7.25 GHz up to 8.4 GHz (15% of bandwidth), where both bands, reception (RX) and transmission (TX) are included simultaneously and Left Handed Circular Polarization (LHCP) and Right Handed Circular Polarization (RHCP) are interchangeable. The antenna is compact, narrow bandwidth and reaches a gain of 16 dBi. It has the capability to steer in elevation to 45±, 75±, 105± and 135± electronically with a Butler matrix and 360± in azimuth with a motorized junction.

Novel dual-band single circular polarization antenna feeding network for satellite communications

In this paper a novel dual-band single circular polarization antenna feeding network for satellite communications is presented. The novel antenna feed chain1 is composed of two elements or subsystems, namely a diplexer and a bi-phase polarizer. In comparison with the classic topology based on an orthomode transducer and a dual-band polarizer, the proposed feed chain presents several advantages, such as compactness, modular design of the different components, broadband operation and versatility in the subsystems interconnection. The design procedure of this new antenna feed configuration is explained. Different examples of antenna feeding networks at 20/30 GHz are presented. It is pointed out the excellent results obtained in terms of isolation and axial ratio.

Improving the pass-band return loss in liquid crystal dual-mode bandpass filters by microstrip patch reshaping

In this paper, the design and experimental characterization of a tunable microstrip bandpass filter based on liquid crystal technology are presented. A reshaped microstrip dual-mode filter structure has been used in order to improve the device performance. Specifically, the aim is to increase the pass-band return loss of the filter by narrowing the filter bandwidth. Simulations confirm the improvement of using this new structure, achieving a pass-band return loss increase of 1.5 dB at least. Because of the anisotropic properties of LC molecules, a filter central frequency shift from 4.688 GHz to 5.045 GHz, which means a relative tuning range of 7.3%, is measured when an external AC voltage from 0 Vrms to 15 Vrms is applied to the device.

Development of Efficient Techniques for the Analysis and Design of Antennas in Dual-Reflectarray Configuration

This thesis contributes to the analysis and design of printed reflectarray antennas. The main part of the work is focused on the analysis of dual offset antennas comprising two reflectarray surfaces, one of them acts as sub-reflector and the second one acts as mainreflector. These configurations introduce additional complexity in several aspects respect to conventional dual offset reflectors, however they present a lot of degrees of freedom that can be used to improve the electrical performance of the antenna. The thesis is organized in four parts: the development of an analysis technique for dualreflectarray antennas, a preliminary validation of such methodology using equivalent reflector systems as reference antennas, a more rigorous validation of the software tool by manufacturing and testing a dual-reflectarray antenna demonstrator and the practical design of dual-reflectarray systems for some applications that show the potential of these kind of configurations to scan the beam and to generate contoured beams. In the first part, a general tool has been implemented to analyze high gain antennas which are constructed of two flat reflectarray structures. The classic reflectarray analysis based on MoM under local periodicity assumption is used for both sub and main reflectarrays, taking into account the incident angle on each reflectarray element. The incident field on the main reflectarray is computed taking into account the field radiated by all the elements on the sub-reflectarray.. Two approaches have been developed, one which employs a simple approximation to reduce the computer run time, and the other which does not, but offers in many cases, improved accuracy. The approximation is based on computing the reflected field on each element on the main reflectarray only once for all the fields radiated by the sub-reflectarray elements, assuming that the response will be the same because the only difference is a small variation on the angle of incidence. This approximation is very accurate when the reflectarray elements on the main reflectarray show a relatively small sensitivity to the angle of incidence. An extension of the analysis technique has been implemented to study dual-reflectarray antennas comprising a main reflectarray printed on a parabolic surface, or in general in a curved surface. In many applications of dual-reflectarray configurations, the reflectarray elements are in the near field of the feed-horn. To consider the near field radiated by the horn, the incident field on each reflectarray element is computed using a spherical mode expansion. In this region, the angles of incidence are moderately wide, and they are considered in the analysis of the reflectarray to better calculate the actual incident field on the sub-reflectarray elements. This technique increases the accuracy for the prediction of co- and cross-polar patterns and antenna gain respect to the case of using ideal feed models. In the second part, as a preliminary validation, the proposed analysis method has been used to design a dual-reflectarray antenna that emulates previous dual-reflector antennas in Ku and W-bands including a reflectarray as subreflector. The results for the dualreflectarray antenna compare very well with those of the parabolic reflector and reflectarray subreflector; radiation patterns, antenna gain and efficiency are practically the same when the main parabolic reflector is substituted by a flat reflectarray. The results show that the gain is only reduced by a few tenths of a dB as a result of the ohmic losses in the reflectarray. The phase adjustment on two surfaces provided by the dual-reflectarray configuration can be used to improve the antenna performance in some applications requiring multiple beams, beam scanning or shaped beams. Third, a very challenging dual-reflectarray antenna demonstrator has been designed, manufactured and tested for a more rigorous validation of the analysis technique presented. The proposed antenna configuration has the feed, the sub-reflectarray and the main-reflectarray in the near field one to each other, so that the conventional far field approximations are not suitable for the analysis of such antenna. This geometry is used as benchmarking for the proposed analysis tool in very stringent conditions. Some aspects of the proposed analysis technique that allow improving the accuracy of the analysis are also discussed. These improvements include a novel method to reduce the inherent cross polarization which is introduced mainly from grounded patch arrays. It has been checked that cross polarization in offset reflectarrays can be significantly reduced by properly adjusting the patch dimensions in the reflectarray in order to produce an overall cancellation of the cross-polarization. The dimensions of the patches are adjusted in order not only to provide the required phase-distribution to shape the beam, but also to exploit the crosses by zero of the cross-polarization components. The last part of the thesis deals with direct applications of the technique described. The technique presented is directly applicable to the design of contoured beam antennas for DBS applications, where the requirements of cross-polarisation are very stringent. The beam shaping is achieved by synthesithing the phase distribution on the main reflectarray while the sub-reflectarray emulates an equivalent hyperbolic subreflector. Dual-reflectarray antennas present also the ability to scan the beam over small angles about boresight. Two possible architectures for a Ku-band antenna are also described based on a dual planar reflectarray configuration that provides electronic beam scanning in a limited angular range. In the first architecture, the beam scanning is achieved by introducing a phase-control in the elements of the sub-reflectarray and the mainreflectarray is passive. A second alternative is also studied, in which the beam scanning is produced using 1-bit control on the main reflectarray, while a passive subreflectarray is designed to provide a large focal distance within a compact configuration. The system aims to develop a solution for bi-directional satellite links for emergency communications. In both proposed architectures, the objective is to provide a compact optics and simplicity to be folded and deployed.

Electronic Steering antenna onboard for satellite communications in X band.

The antenna presented in this article will be developed for satellite communications onboard systems based on the recommendations ITU-R S.580-6 and ITU-R S.465-5. The antenna consists of printed elements grouped in an array, this terminal works in a frequency band from 7.25 up to 8.4 GHz (14.7% of bandwidth), where both bands, reception (7.25 - 7.75 GHz) and transmission (7.9 - 8.4 GHz), are included simultaneously. The antenna reaches a gain about 31 dBi, and it has a radiation pattern with a beamwidth smaller than 10° and a dual circular polarization. The antenna has the capability to steer in elevation from 90° to 40° electronically and 360° in azimuth with a motorized junction.

Modular Planar Antenna at X-band for satellite communications

An antenna which has been conceived as a portable system for satellite communications based on the recommendations ITU-R S.580-6 [1] and ITU-R S.465-5 [2] for small antennas, i.e., with a diameter lower than 50 wavelengths, is introduced. It is a planar and a compact structure with a size of 40×40×2 cm. The antenna is formed by an array of 256 printed elements covering a large bandwidth (14.7%) at X-Band. The specification includes transmission (Tx) and reception (Rx) bands simultaneously. The printed antenna has a radiation pattern with a 3dB beamwidth of 5°, over a 31dBi gain, and a dual and an interchangeable circular polarization

Portable low profile antenna at X-band

An antenna which has been conceived as a portable system for satellite communications based on the recommendations ITU-R S.580-6 and ITU-R S.465-5 for small antennas, i.e., with a diameter lower than 50 wavelengths, is introduced. It is a planar and a compact structure with a size of 40×40×2 cm. The antenna is formed by an array of 256 printed elements covering a large bandwidth (14.7%) at X-Band with a VSWR of 1.4:1. The specification includes transmission (Tx) and reception (Rx) bands simultaneously. The printed antenna has a radiation pattern with a 3dB beamwidth of 5°, over a 31dBi gain, and a dual and an interchangeable circular polarization.

Man-pack antenna at X-band

In this paper a low cost man-pack antenna for satellite communications at X band is presented. The antenna has dual circular polarization in Tx and Rx.

Analysis and design of reconfigurable multimode multiport microstrip antennas for mimo systems and diversity schemes

Las comunicaciones inalámbricas han transformado profundamente la forma en la que la gente se comunica en el día a día y es, sin lugar a dudas, una de las tecnologías de nuestro tiempo que más rápidamente evoluciona. Este rápido crecimiento implica retos enormes en la tecnología subyacente, debido y entre otros motivos, a la gran demanda de capacidad de los nuevos servicios inalámbricos. Los sistemas Multiple Input Multiple Output (MIMO) han despertado mucho interés como medio de mejorar el rendimiento global del sistema, satisfaciendo de este modo y en cierta medida los nuevo requisitos exigidos. De hecho, el papel relevante de esta tecnología en los actuales esfuerzos de estandarización internacionales pone de manifiesto esta utilidad. Los sistemas MIMO sacan provecho de los grados de libertad espaciales, disponibles a través del entorno multitrayecto, para mejorar el rendimiento de la comunicación con una destacable eficiencia espectral. Con el fin de alcanzar esta mejora en el rendimiento, la diversidad espacial y por diagrama han sido empleadas tradicionalmente para reducir la correlación entre los elementos radiantes, ya que una correlación baja es condición necesaria, si bien no suficiente, para dicha mejora. Tomando como referencia, o punto de partida, las técnicas empleadas para obtener diversidad por diagrama, esta tesis doctoral surge de la búsqueda de la obtención de diversidad por diagrama y/o multiplexación espacial a través del comportamiento multimodal de la antena microstrip, proponiendo para ello un modelo cuasi analítico original para el análisis y diseño de antenas microstrip multipuerto, multimodo y reconfigurables. Este novedoso enfoque en este campo, en vez de recurrir a simulaciones de onda completa por medio de herramientas comerciales tal y como se emplea en las publicaciones existentes, reduce significativamente el esfuerzo global de análisis y diseño, en este último caso por medio de guías de diseño generales. Con el fin de lograr el objetivo planteado y después de una revisión de los principales conceptos de los sistemas MIMO que se emplearán más adelante, se fija la atención en encontrar, implementar y verificar la corrección y exactitud de un modelo analítico que sirva de base sobre la cual añadir las mejoras necesarias para obtener las características buscadas del modelo cuasi analítico propuesto. Posteriormente y partiendo del modelo analítico base seleccionado, se exploran en profundidad y en diferentes entornos multitrayecto, las posibilidades en cuanto a rendimiento se refiere de diversidad por diagrama y multiplexación espacial, proporcionadas por el comportamiento multimodal de las antenas parche microstrip sin cargar. Puesto que cada modo de la cavidad tiene su propia frecuencia de resonancia, es necesario encontrar formas de desplazar la frecuencia de resonancia de cada modo empleado para ubicarlas en la misma banda de frecuencia, manteniendo cada modo al mismo tiempo tan independiente como sea posible. Este objetivo puede lograrse cargando adecuadamente la cavidad con cargas reactivas, o alterando la geometría del parche radiante. Por consiguiente, la atención en este punto se fija en el diseño, implementación y verificación de un modelo cuasi analítico para el análisis de antenas parche microstrip multipuerto, multimodo y cargadas que permita llevar a cabo la tarea indicada, el cuál es una de las contribuciones principales de esta tesis doctoral. Finalmente y basándose en el conocimiento adquirido a través del modelo cuasi analítico, se proporcionan y aplican guías generales para el diseño de antenas microstrip multipuerto, multimodo y reconfigurables para sistemas MIMO, con el fin de mejorar su diversidad por diagrama y/o su capacidad por medio del comportamiento multimodal de las antenas parche microstrip. Se debe destacar que el trabajo presentado en esta tesis doctoral ha dado lugar a una publicación en una revista técnica internacional de un alto factor de impacto. De igual manera, el trabajo también ha sido presentado en algunas de las más importantes conferencias internacionales en el ámbito de las antenas ABSTRACT Wireless communications have deeply transformed the way people communicate on daily basis and it is undoubtedly one of the most rapidly evolving technologies of our time. This fast growing behaviour involves huge challenges on the bearing technology, due to and among others reasons, the high demanding capacity of new wireless services. MIMO systems have given rise to considerable interest as a means to enhance the overall system performance, thus satisfying somehow the new demanding requirements. Indeed, the significant role of this technology on current international standardization efforts, highlights this usefulness. MIMO systems make profit from the spatial degrees of freedom available through the multipath scenario to improve the communication performance with a remarkable spectral efficiency. In order to achieve this performance improvement, spatial and pattern diversity have been traditionally used to decrease the correlation between antenna elements, as low correlation is a necessary but not sufficient condition. Taking as a reference, or starting point, the techniques used to achieve pattern diversity, this Philosophiae Doctor (Ph.D.) arises from the pursuit of obtaining pattern diversity and/or spatial multiplexing capabilities through the multimode microstrip behaviour, thus proposing a novel quasi analytical model for the analysis and design of reconfigurable multimode multiport microstrip antennas. This innovative approach on this field, instead of resorting to full-wave simulations through commercial tools as done in the available publications, significantly reduces the overall analysis and design effort, in this last case through comprehensive design guidelines. In order to achieve this goal and after a review of the main concepts of MIMO systems which will be followed used, the spotlight is fixed on finding, implementing and verifying the correctness and accuracy of a base quasi analytical model over which add the necessary enhancements to obtain the sought features of the quasi analytical model proposed. Afterwards and starting from the base quasi analytical model selected, the pattern diversity and spatial multiplexing performance capabilities provided by the multimode behaviour of unloaded microstrip patch antennas under different multipath environments are fully explored. As each cavity mode has its own resonant frequency, it is required to find ways to displace the resonant frequency of each used mode to place them at the same frequency band while keeping each mode as independent as possible. This objective can be accomplished with an appropriate loading of the cavity with reactive loads, or through the alteration of the geometry of the radiation patch. Thus, the focus is set at this point on the design, implementation and verification of a quasi analytical model for the analysis of loaded multimode multiport microstrip patch antennas to carry out the aforementioned task, which is one of the main contributions of this Ph.D. Finally and based on the knowledge acquired through the quasi analytical model, comprehensive guidelines to design reconfigurable multimode MIMO microstrip antennas to improve the spatial multiplexing and/or diversity system performance by means of the multimode microstrip patch antenna behaviour are given and applied. It shall be highlighted that the work presented in this Ph.D. has given rise to a publication in an international technical journal of high impact factor. Moreover, the work has also been presented at some of the most important international conferences in antenna area.

A Transportable Reflectarray Antenna for Satellite Ku-band Emergency Communications

The design of a Ku-band reconfigurable reflectarray antenna for emergency satellite communications is presented. Bidirectional high data rate satellite links are needed in emergency conditions where other telecommunication infrastructures are not available. In order to operate in this type of scenario, an antenna should be deployable, transportable, and easily repointable. The need of an automatic and fast satellite location and pointing system leads to a completely electronic reconfigurable antenna. The operative bandwidth is from 10.7 to 12.5 GHz for reception and from 14 up to 14.5 GHz for transmission (30% of relative bandwidth). The selected antenna architecture is based on a dual reflectarray system comprising a passive subreflectarray and an active main reflectarray made of reconfigurable 1-bit elementary cells based on PIN diodes.

Reflectarray antennas for dual polarization and broadband telecom satellite applications

A reflectarray antenna with improved performance is proposed to operate in dual-polarization and transmit-receive frequencies in Ku-band for broadcast satellite applications. The reflectarray element contains two orthogonal sets of four coplanar parallel dipoles printed on two surfaces, each set combining lateral and broadside coupling. A 40-cm prototype has been designed, manufactured, and tested. The lengths of the coupled dipoles in the reflectarray cells have been optimized to produce a collimated beam in dual polarization in the transmit and receive bands. The measured radiation patterns confirm the high performance of the antenna in terms of bandwidth (27%), low losses, and low levels of cross polarization. Some preliminary simulations at 11.95 GHz for a 1.2-m antenna with South American coverage are presented to show the potential of the proposed antenna for spaceborne antennas in Ku-band.