The PSE-3D instability analysis methodology for flows depending strongly on two and weakly on the third spatial dimension

The present contribution discusses the development of a PSE-3D instability analysis algorithm, in which a matrix forming and storing approach is followed. Alternatively to the typically used in stability calculations spectral methods, new stable high-order finitedifference-based numerical schemes for spatial discretization 1 are employed. Attention is paid to the issue of efficiency, which is critical for the success of the overall algorithm. To this end, use is made of a parallelizable sparse matrix linear algebra package which takes advantage of the sparsity offered by the finite-difference scheme and, as expected, is shown to perform substantially more efficiently than when spectral collocation methods are used. The building blocks of the algorithm have been implemented and extensively validated, focusing on classic PSE analysis of instability on the flow-plate boundary layer, temporal and spatial BiGlobal EVP solutions (the latter necessary for the initialization of the PSE-3D), as well as standard PSE in a cylindrical coordinates using the nonparallel Batchelor vortex basic flow model, such that comparisons between PSE and PSE-3D be possible; excellent agreement is shown in all aforementioned comparisons. Finally, the linear PSE-3D instability analysis is applied to a fully three-dimensional flow composed of a counter-rotating pair of nonparallel Batchelor vortices.

Remarks on methods for the computation of boundary-element integrals by co-ordinate transformation

It is well known that the evaluation of the influence matrices in the boundary-element method requires the computation of singular integrals. Quadrature formulae exist which are especially tailored to the specific nature of the singularity, i.e. log(*- x0)9 Ijx- JC0), etc. Clearly the nodes and weights of these formulae vary with the location Xo of the singular point. A drawback of this approach is that a given problem usually includes different types of singularities, and therefore a general-purpose code would have to include many alternative formulae to cater for all possible cases. Recently, several authors1"3 have suggested a type independent alternative technique based on the combination of standard Gaussian rules with non-linear co-ordinate transformations. The transformation approach is particularly appealing in connection with the p.adaptive version, where the location of the collocation points varies at each step of the refinement process. The purpose of this paper is to analyse the technique in eference 3. We show that this technique is asymptotically correct as the number of Gauss points increases. However, the method possesses a 'hidden' source of error that is analysed and can easily be removed.

Order 10 4 speedup in global linear instability analysis using matrix formation

A unified solution framework is presented for one-, two- or three-dimensional complex non-symmetric eigenvalue problems, respectively governing linear modal instability of incompressible fluid flows in rectangular domains having two, one or no homogeneous spatial directions. The solution algorithm is based on subspace iteration in which the spatial discretization matrix is formed, stored and inverted serially. Results delivered by spectral collocation based on the Chebyshev-Gauss-Lobatto (CGL) points and a suite of high-order finite-difference methods comprising the previously employed for this type of work Dispersion-Relation-Preserving (DRP) and Padé finite-difference schemes, as well as the Summationby- parts (SBP) and the new high-order finite-difference scheme of order q (FD-q) have been compared from the point of view of accuracy and efficiency in standard validation cases of temporal local and BiGlobal linear instability. The FD-q method has been found to significantly outperform all other finite difference schemes in solving classic linear local, BiGlobal, and TriGlobal eigenvalue problems, as regards both memory and CPU time requirements. Results shown in the present study disprove the paradigm that spectral methods are superior to finite difference methods in terms of computational cost, at equal accuracy, FD-q spatial discretization delivering a speedup of ð (10 4). Consequently, accurate solutions of the three-dimensional (TriGlobal) eigenvalue problems may be solved on typical desktop computers with modest computational effort.

Combining a Similar Coefficient Identification Algorithm with the Boundary Element Method

The boundary element method (BEM) has been applied successfully to many engineering problems during the last decades. Compared with domain type methods like the finite element method (FEM) or the finite difference method (FDM) the BEM can handle problems where the medium extends to infinity much easier than domain type methods as there is no need to develop special boundary conditions (quiet or absorbing boundaries) or infinite elements at the boundaries introduced to limit the domain studied. The determination of the dynamic stiffness of arbitrarily shaped footings is just one of these fields where the BEM has been the method of choice, especially in the 1980s. With the continuous development of computer technology and the available hardware equipment the size of the problems under study grew and, as the flop count for solving the resulting linear system of equations grows with the third power of the number of equations, there was a need for the development of iterative methods with better performance. In [1] the GMRES algorithm was presented which is now widely used for implementations of the collocation BEM. While the FEM results in sparsely populated coefficient matrices, the BEM leads, in general, to fully or densely populated ones, depending on the number of subregions, posing a serious memory problem even for todays computers. If the geometry of the problem permits the surface of the domain to be meshed with equally shaped elements a lot of the resulting coefficients will be calculated and stored repeatedly. The present paper shows how these unnecessary operations can be avoided reducing the calculation time as well as the storage requirement. To this end a similar coefficient identification algorithm (SCIA), has been developed and implemented in a program written in Fortran 90. The vertical dynamic stiffness of a single pile in layered soil has been chosen to test the performance of the implementation. The results obtained with the 3-d model may be compared with those obtained with an axisymmetric formulation which are considered to be the reference values as the mesh quality is much better. The entire 3D model comprises more than 35000 dofs being a soil region with 21168 dofs the biggest single region. Note that the memory necessary to store all coefficients of this single region is about 6.8 GB, an amount which is usually not available with personal computers. In the problem under study the interface zone between the two adjacent soil regions as well as the surface of the top layer may be meshed with equally sized elements. In this case the application of the SCIA leads to an important reduction in memory requirements. The maximum memory used during the calculation has been reduced to 1.2 GB. The application of the SCIA thus permits problems to be solved on personal computers which otherwise would require much more powerful hardware.

Determinación de un modelo de geoide gravimétrico para Puerto Rico como sistema de referencia para las altitudes ortométricas

El geoide, definido como la superficie equipotencial que mejor se ajusta (en el sentido de los mínimos cuadrados) al nivel medio del mar en una determinada época, es la superficie que utilizamos como referencia para determinar las altitudes ortométricas. Si disponemos de una superficie equipotencial de referencia como dátum altimétrico preciso o geoide local, podemos entonces determinar las altitudes ortométricas de forma eficiente a partir de las altitudes elipsoidales proporcionadas por el Sistema Global de Navegación por Satélite (Global Navigation Satellite System, GNSS ). Como es sabido uno de los problemas no resueltos de la geodesia (quizás el más importante de los mismos en la actualidad) es la carencia de un dátum altimétrico global (Sjoberg, 2011) con las precisiones adecuadas. Al no existir un dátum altimétrico global que nos permita obtener los valores absolutos de la ondulación del geoide con la precisión requerida, es necesario emplear modelos geopotenciales como alternativa. Recientemente fue publicado el modelo EGM2008 en el que ha habido una notable mejoría de sus tres fuentes de datos, por lo que este modelo contiene coeficientes adicionales hasta el grado 2190 y orden 2159 y supone una sustancial mejora en la precisión (Pavlis et al., 2008). Cuando en una región determinada se dispone de valores de gravedad y Modelos Digitales del Terreno (MDT) de calidad, es posible obtener modelos de superficies geopotenciales más precisos y de mayor resolución que los modelos globales. Si bien es cierto que el Servicio Nacional Geodésico de los Estados Unidos de América (National Geodetic Survey, NGS) ha estado desarrollando modelos del geoide para la región de los Estados Unidos de América continentales y todos sus territorios desde la década de los noventa, también es cierto que las zonas de Puerto Rico y las Islas Vírgenes Estadounidenses han quedado un poco rezagadas al momento de poder aplicar y obtener resultados de mayor precisión con estos modelos regionales del geoide. En la actualidad, el modelo geopotencial regional vigente para la zona de Puerto Rico y las Islas Vírgenes Estadounidenses es el GEOID12A (Roman y Weston, 2012). Dada la necesidad y ante la incertidumbre de saber cuál sería el comportamiento de un modelo del geoide desarrollado única y exclusivamente con datos de gravedad locales, nos hemos dado a la tarea de desarrollar un modelo de geoide gravimétrico como sistema de referencia para las altitudes ortométricas. Para desarrollar un modelo del geoide gravimétrico en la isla de Puerto Rico, fue necesario implementar una metodología que nos permitiera analizar y validar los datos de gravedad terrestre existentes. Utilizando validación por altimetría con sistemas de información geográfica y validación matemática por colocación con el programa Gravsoft (Tscherning et al., 1994) en su modalidad en Python (Nielsen et al., 2012), fue posible validar 1673 datos de anomalías aire libre de un total de 1894 observaciones obtenidas de la base de datos del Bureau Gravimétrico Internacional (BGI). El aplicar estas metodologías nos permitió obtener una base de datos anomalías de la gravedad fiable la cual puede ser utilizada para una gran cantidad de aplicaciones en ciencia e ingeniería. Ante la poca densidad de datos de gravedad existentes, fue necesario emplear un método alternativo para densificar los valores de anomalías aire libre existentes. Empleando una metodología propuesta por Jekeli et al. (2009b) se procedió a determinar anomalías aire libre a partir de los datos de un MDT. Estas anomalías fueron ajustadas utilizando las anomalías aire libre validadas y tras aplicar un ajuste de mínimos cuadrados por zonas geográficas, fue posible obtener una malla de datos de anomalías aire libre uniforme a partir de un MDT. Tras realizar las correcciones topográficas, determinar el efecto indirecto de la topografía del terreno y la contribución del modelo geopotencial EGM2008, se obtuvo una malla de anomalías residuales. Estas anomalías residuales fueron utilizadas para determinar el geoide gravimétrico utilizando varias técnicas entre las que se encuentran la aproximación plana de la función de Stokes y las modificaciones al núcleo de Stokes, propuestas por Wong y Gore (1969), Vanicek y Kleusberg (1987) y Featherstone et al. (1998). Ya determinados los distintos modelos del geoide gravimétrico, fue necesario validar los mismos y para eso se utilizaron una serie de estaciones permanentes de la red de nivelación del Datum Vertical de Puerto Rico de 2002 (Puerto Rico Vertical Datum 2002, PRVD02 ), las cuales tenían publicados sus valores de altitud elipsoidal y elevación. Ante la ausencia de altitudes ortométricas en las estaciones permanentes de la red de nivelación, se utilizaron las elevaciones obtenidas a partir de nivelación de primer orden para determinar los valores de la ondulación del geoide geométrico (Roman et al., 2013). Tras establecer un total de 990 líneas base, se realizaron dos análisis para determinar la 'precisión' de los modelos del geoide. En el primer análisis, que consistió en analizar las diferencias entre los incrementos de la ondulación del geoide geométrico y los incrementos de la ondulación del geoide de los distintos modelos (modelos gravimétricos, EGM2008 y GEOID12A) en función de las distancias entre las estaciones de validación, se encontró que el modelo con la modificación del núcleo de Stokes propuesta por Wong y Gore presentó la mejor 'precisión' en un 91,1% de los tramos analizados. En un segundo análisis, en el que se consideraron las 990 líneas base, se determinaron las diferencias entre los incrementos de la ondulación del geoide geométrico y los incrementos de la ondulación del geoide de los distintos modelos (modelos gravimétricos, EGM2008 y GEOID12A), encontrando que el modelo que presenta la mayor 'precisión' también era el geoide con la modificación del núcleo de Stokes propuesta por Wong y Gore. En este análisis, el modelo del geoide gravimétrico de Wong y Gore presento una 'precisión' de 0,027 metros en comparación con la 'precisión' del modelo EGM2008 que fue de 0,031 metros mientras que la 'precisión' del modelo regional GEOID12A fue de 0,057 metros. Finalmente podemos decir que la metodología aquí presentada es una adecuada ya que fue posible obtener un modelo del geoide gravimétrico que presenta una mayor 'precisión' que los modelos geopotenciales disponibles, incluso superando la precisión del modelo geopotencial global EGM2008. ABSTRACT The geoid, defined as the equipotential surface that best fits (in the least squares sense) to the mean sea level at a particular time, is the surface used as a reference to determine the orthometric heights. If we have an equipotential reference surface or a precise local geoid, we can then determine the orthometric heights efficiently from the ellipsoidal heights, provided by the Global Navigation Satellite System (GNSS). One of the most common and important an unsolved problem in geodesy is the lack of a global altimetric datum (Sjoberg, 2011)) with the appropriate precision. In the absence of one which allows us to obtain the absolute values of the geoid undulation with the required precision, it is necessary to use alternative geopotential models. The EGM2008 was recently published, in which there has been a marked improvement of its three data sources, so this model contains additional coefficients of degree up to 2190 and order 2159, and there is a substantial improvement in accuracy (Pavlis et al., 2008). When a given region has gravity values and high quality digital terrain models (DTM), it is possible to obtain more accurate regional geopotential models, with a higher resolution and precision, than global geopotential models. It is true that the National Geodetic Survey of the United States of America (NGS) has been developing geoid models for the region of the continental United States of America and its territories from the nineties, but which is also true is that areas such as Puerto Rico and the U.S. Virgin Islands have lagged behind when to apply and get more accurate results with these regional geopotential models. Right now, the available geopotential model for Puerto Rico and the U.S. Virgin Islands is the GEOID12A (Roman y Weston, 2012). Given this need and given the uncertainty of knowing the behavior of a regional geoid model developed exclusively with data from local gravity, we have taken on the task of developing a gravimetric geoid model to use as a reference system for orthometric heights. To develop a gravimetric geoid model in the island of Puerto Rico, implementing a methodology that allows us to analyze and validate the existing terrestrial gravity data is a must. Using altimetry validation with GIS and mathematical validation by collocation with the Gravsoft suite programs (Tscherning et al., 1994) in its Python version (Nielsen et al., 2012), it was possible to validate 1673 observations with gravity anomalies values out of a total of 1894 observations obtained from the International Bureau Gravimetric (BGI ) database. Applying these methodologies allowed us to obtain a database of reliable gravity anomalies, which can be used for many applications in science and engineering. Given the low density of existing gravity data, it was necessary to employ an alternative method for densifying the existing gravity anomalies set. Employing the methodology proposed by Jekeli et al. (2009b) we proceeded to determine gravity anomaly data from a DTM. These anomalies were adjusted by using the validated free-air gravity anomalies and, after that, applying the best fit in the least-square sense by geographical area, it was possible to obtain a uniform grid of free-air anomalies obtained from a DTM. After applying the topographic corrections, determining the indirect effect of topography and the contribution of the global geopotential model EGM2008, a grid of residual anomalies was obtained. These residual anomalies were used to determine the gravimetric geoid by using various techniques, among which are the planar approximation of the Stokes function and the modifications of the Stokes kernel, proposed by Wong y Gore (1969), Vanicek y Kleusberg (1987) and Featherstone et al. (1998). After determining the different gravimetric geoid models, it was necessary to validate them by using a series of stations of the Puerto Rico Vertical Datum of 2002 (PRVD02) leveling network. These stations had published its values of ellipsoidal height and elevation, and in the absence of orthometric heights, we use the elevations obtained from first - order leveling to determine the geometric geoid undulation (Roman et al., 2013). After determine a total of 990 baselines, two analyzes were performed to determine the ' accuracy ' of the geoid models. The first analysis was to analyze the differences between the increments of the geometric geoid undulation with the increments of the geoid undulation of the different geoid models (gravimetric models, EGM2008 and GEOID12A) in function of the distance between the validation stations. Through this analysis, it was determined that the model with the modified Stokes kernel given by Wong and Gore had the best 'accuracy' in 91,1% for the analyzed baselines. In the second analysis, in which we considered the 990 baselines, we analyze the differences between the increments of the geometric geoid undulation with the increments of the geoid undulation of the different geoid models (gravimetric models, EGM2008 and GEOID12A) finding that the model with the highest 'accuracy' was also the model with modifying Stokes kernel given by Wong and Gore. In this analysis, the Wong and Gore gravimetric geoid model presented an 'accuracy' of 0,027 meters in comparison with the 'accuracy' of global geopotential model EGM2008, which gave us an 'accuracy' of 0,031 meters, while the 'accuracy ' of the GEOID12A regional model was 0,057 meters. Finally we can say that the methodology presented here is adequate as it was possible to obtain a gravimetric geoid model that has a greater 'accuracy' than the geopotential models available, even surpassing the accuracy of global geopotential model EGM2008.

Estudio de la precisión en la determinación del coeficiente de absorción acústica en tubo de impedancia

El objetivo del presente Trabajo Fin de Máster es estudiar la precisión de los resultados obtenidos en la medición del coeficiente de absorción acústica en tubo de impedancia, según la norma UNE-EN ISO 10534-2 “Determinación del coeficiente de absorción acústica y de la impedancia acústica en tubos de impedancia. Parte 2: Método de la función de transferencia”. En primer lugar, se han estudiado los fundamentos teóricos relacionados con el método de ensayo. A continuación, se ha detallado dicho método y se ha aplicado a un caso práctico con la instrumentación disponible en el laboratorio de Acústica de la Escuela. En relación a la precisión del método se ha analizado si la preparación e instalación de la muestra son causas de imprecisión. Para ello, se han realizado varios ensayos con dos tipos de materiales acústicos, con el fin de estudiar la dispersión entre los resultados que produce tanto el corte de la muestra, realizado en el proceso de confección, como su colocación en el tubo de impedancia. Además, se ha estudiado si desviaciones en la medida de la temperatura y de la distancia entre los micrófonos influyen en los valores del coeficiente de absorción acústica medido y de su incertidumbre asociada. Puesto que el resultado de un ensayo únicamente se halla completo cuando está acompañado de una declaración acerca de la incertidumbre de dicho resultado, en el presente trabajo se ha aplicado a este método de ensayo un procedimiento para estimar la incertidumbre empleando el método de Monte Carlo. ABSTRACT The objective of this project is studying the precision of the measurements of sound absorption coefficient in impedance tube, according to standard UNE-EN ISO 10534-2 “Determination of sound absorption coefficient and impedance in impedance tubes. Part 2: Transfer-function method”. Firstly, theoretical basis related to the test method have been studied. Furthermore, this method has been defined and applied to a particular case with the instrumentation available in the Acoustics laboratory of the College. In relation to the precision of the method, the preparation and installation of the test sample have been analyzed as possible causes of imprecision. For this purpose, two types of acoustic materials have been tested in order to study the deviation between the results produced by the cutting of the test sample and the collocation in impedance tube. In addition, it has been studied if deviations in the measurement of the temperature and distance between microphones may influence the sound absorption coefficient measured and its associated uncertainty. The test result must be accompanied by a statement of the uncertainty of the result. For this reason, in this project a procedure for estimating uncertainty of the result of this test method has been applied using the Monte Carlo method.

Analysis of the geometric altimetry to support aircraft optimal trajectories within the future 4d trajectory management

Over the past few years, the common practice within air traffic management has been that commercial aircraft fly by following a set of predefined routes to reach their destination. Currently, aircraft operators are requesting more flexibility to fly according to their prefer- ences, in order to achieve their business objectives. Due to this reason, much research effort is being invested in developing different techniques which evaluate aircraft optimal trajectory and traffic synchronisation. Also, the inefficient use of the airspace using barometric altitude overall in the landing and takeoff phases or in Continuous Descent Approach (CDA) trajectories where currently it is necessary introduce the necessary reference setting (QNH or QFE). To solve this problem and to permit a better airspace management born the interest of this research. Where the main goals will be to evaluate the impact, weakness and strength of the use of geometrical altitude instead of the use of barometric altitude. Moreover, this dissertation propose the design a simplified trajectory simulator which is able to predict aircraft trajectories. The model is based on a three degrees of freedom aircraft point mass model that can adapt aircraft performance data from Base of Aircraft Data, and meteorological information. A feature of this trajectory simulator is to support the improvement of the strategic and pre-tactical trajectory planning in the future Air Traffic Management. To this end, the error of the tool (aircraft Trajectory Simulator) is measured by comparing its performance variables with actual flown trajectories obtained from Flight Data Recorder information. The trajectory simulator is validated by analysing the performance of different type of aircraft and considering different routes. A fuel consumption estimation error was identified and a correction is proposed for each type of aircraft model. In the future Air Traffic Management (ATM) system, the trajectory becomes the fundamental element of a new set of operating procedures collectively referred to as Trajectory-Based Operations (TBO). Thus, governmental institutions, academia, and industry have shown a renewed interest for the application of trajectory optimisation techniques in com- mercial aviation. The trajectory optimisation problem can be solved using optimal control methods. In this research we present and discuss the existing methods for solving optimal control problems focusing on direct collocation, which has received recent attention by the scientific community. In particular, two families of collocation methods are analysed, i.e., Hermite-Legendre-Gauss-Lobatto collocation and the pseudospectral collocation. They are first compared based on a benchmark case study: the minimum fuel trajectory problem with fixed arrival time. For the sake of scalability to more realistic problems, the different meth- ods are also tested based on a real Airbus 319 El Cairo-Madrid flight. Results show that pseudospectral collocation, which has shown to be numerically more accurate and computa- tionally much faster, is suitable for the type of problems arising in trajectory optimisation with application to ATM. Fast and accurate optimal trajectory can contribute properly to achieve the new challenges of the future ATM. As atmosphere uncertainties are one of the most important issues in the trajectory plan- ning, the final objective of this dissertation is to have a magnitude order of how different is the fuel consumption under different atmosphere condition. Is important to note that in the strategic phase planning the optimal trajectories are determined by meteorological predictions which differ from the moment of the flight. The optimal trajectories have shown savings of at least 500 [kg] in the majority of the atmosphere condition (different pressure, and temperature at Mean Sea Level, and different lapse rate temperature) with respect to the conventional procedure simulated at the same atmosphere condition.This results show that the implementation of optimal profiles are beneficial under the current Air traffic Management (ATM).

Desarrollo, implementación y análisis de un modelo cinemático local de velocidades para Costa Rica basado en la integración y homogenización de datos de estaciones GNSS continuas

El primer procesamiento estricto realizado con el software científico Bernese y contemplando las más estrictas normas de cálculo recomendadas internacionalmente, permitió obtener un campo puntual de alta exactitud, basado en la integración y estandarización de los datos de una red GPS ubicada en Costa Rica. Este procesamiento contempló un total de 119 semanas de datos diarios, es decir unos 2,3 años, desde enero del año 2009 hasta abril del año 2011, para un total de 30 estaciones GPS, de las cuales 22 están ubicadas en el territorio nacional de Costa Rica y 8 internaciones pertenecientes a la red del Sistema Geocéntrico para las Américas (SIRGAS). Las denominadas soluciones semilibres generaron, semana a semana, una red GPS con una alta exactitud interna definida por medio de los vectores entre las estaciones y las coordenadas finales de la constelación satelital. La evaluación semanal dada por la repetibilidad de las soluciones brindó en promedio errores de 1,7 mm, 1,4 mm y 5,1 mm en las componentes [n e u], confirmando una alta consistencia en estas soluciones. Aunque las soluciones semilibres poseen una alta exactitud interna, las mismas no son utilizables para fines de análisis cinemático, pues carecen de un marco de referencia. En Latinoamérica, la densificación del Marco Internacional Terrestre de Referencia (ITRF), está representado por la red de estaciones de operación continua GNSS de SIRGAS, denominada como SIRGAS-CON. Por medio de las denominadas coordenadas semanales finales de las 8 estaciones consideradas como vínculo, se refirió cada una de las 119 soluciones al marco SIRGAS. La introducción del marco de referencia SIRGAS a las soluciones semilibres produce deformaciones en estas soluciones. Las deformaciones de las soluciones semilibres son producto de las cinemática de cada una de las placas en las que se ubican las estaciones de vínculo. Luego de efectuado el amarre semanal a las coordenadas SIRGAS, se hizo una estimación de los vectores de velocidad de cada una de las estaciones, incluyendo las de amarre, cuyos valores de velocidad se conocen con una alta exactitud. Para la determinación de las velocidades de las estaciones costarricenses, se programó una rutina en ambiente MatLab, basada en una ajuste por mínimos cuadrados. Los valores obtenidos en el marco de este proyecto en comparación con los valores oficiales, brindaron diferencias promedio del orden de los 0,06 cm/a, -0,08 cm/a y -0,10 cm/a respectivamente para las coordenadas [X Y Z]. De esta manera se logró determinar las coordenadas geocéntricas [X Y Z]T y sus variaciones temporales [vX vY vZ]T para el conjunto de 22 estaciones GPS de Costa Rica, dentro del datum IGS05, época de referencia 2010,5. Aunque se logró una alta exactitud en los vectores de coordenadas geocéntricas de las 22 estaciones, para algunas de las estaciones el cálculo de las velocidades no fue representativo debido al relativo corto tiempo (menos de un año) de archivos de datos. Bajo esta premisa, se excluyeron las ocho estaciones ubicadas al sur de país. Esto implicó hacer una estimación del campo local de velocidades con solamente veinte estaciones nacionales más tres estaciones en Panamá y una en Nicaragua. El algoritmo usado fue el denominado Colocación por Mínimos Cuadrados, el cual permite la estimación o interpolación de datos a partir de datos efectivamente conocidos, el cual fue programado mediante una rutina en ambiente MatLab. El campo resultante se estimó con una resolución de 30' X 30' y es altamente constante, con una velocidad resultante promedio de 2,58 cm/a en una dirección de 40,8° en dirección noreste. Este campo fue validado con base en los datos del modelo VEMOS2009, recomendado por SIRGAS. Las diferencias de velocidad promedio para las estaciones usadas como insumo para el cálculo del campo fueron del orden los +0,63 cm/a y +0,22 cm/a para los valores de velocidad en latitud y longitud, lo que supone una buena determinación de los valores de velocidad y de la estimación de la función de covarianza empírica, necesaria para la aplicación del método de colocación. Además, la grilla usada como base para la interpolación brindó diferencias del orden de -0,62 cm/a y -0,12 cm/a para latitud y longitud. Adicionalmente los resultados de este trabajo fueron usados como insumo para hacer una aproximación en la definición del límite del llamado Bloque de Panamá dentro del territorio nacional de Costa Rica. El cálculo de las componentes del Polo de Euler por medio de una rutina programa en ambiente MatLab y aplicado a diferentes combinaciones de puntos no brindó mayores aportes a la definición física de este límite. La estrategia lo que confirmó fue simplemente la diferencia en la dirección de todos los vectores velocidad y no permitió reveló revelar con mayor detalle una ubicación de esta zona dentro del territorio nacional de Costa Rica. ABSTRACT The first strict processing performed with the Bernese scientific software and contemplating the highest standards internationally recommended calculation, yielded a precise field of high accuracy, based on the integration and standardization of data from a GPS network located in Costa Rica. This processing watched a total of 119 weeks of daily data, is about 2.3 years from January 2009 to April 2011, for a total of 30 GPS stations, of which 22 are located in the country of Costa Rica and 8 hospitalizations within the network of Geocentric System for the Americas (SIRGAS). The semi-free solutions generated, every week a GPS network with high internal accuracy defined by vectors between stations and the final coordinates of the satellite constellation. The weekly evaluation given by repeatability of the solutions provided in average errors of 1.7 mm 1.4 mm and 5.1 mm in the components [n e u], confirming a high consistency in these solutions. Although semi-free solutions have a high internal accuracy, they are not used for purposes of kinematic analysis, because they lack a reference frame. In Latin America, the densification of the International Terrestrial Reference Frame (ITRF), is represented by a network of continuously operating GNSS stations SIRGAS, known as SIRGAS-CON. Through weekly final coordinates of the 8 stations considered as a link, described each of the solutions to the frame 119 SIRGAS. The introduction of the frame SIRGAS to semi-free solutions generates deformations. The deformations of the semi-free solutions are products of the kinematics of each of the plates in which link stations are located. After SIRGAS weekly link to SIRGAS frame, an estimate of the velocity vectors of each of the stations was done. The velocity vectors for each SIRGAS stations are known with high accuracy. For this calculation routine in MatLab environment, based on a least squares fit was scheduled. The values obtained compared to the official values, gave average differences of the order of 0.06 cm/yr, -0.08 cm/yr and -0.10 cm/yr respectively for the coordinates [XYZ]. Thus was possible to determine the geocentric coordinates [XYZ]T and its temporal variations [vX vY vZ]T for the set of 22 GPS stations of Costa Rica, within IGS05 datum, reference epoch 2010.5. The high accuracy vector for geocentric coordinates was obtained, however for some stations the velocity vectors was not representative because of the relatively short time (less than one year) of data files. Under this premise, the eight stations located in the south of the country were excluded. This involved an estimate of the local velocity field with only twenty national stations plus three stations in Panama and Nicaragua. The algorithm used was Least Squares Collocation, which allows the estimation and interpolation of data from known data effectively. The algorithm was programmed with MatLab. The resulting field was estimated with a resolution of 30' X 30' and is highly consistent with a resulting average speed of 2.58 cm/y in a direction of 40.8° to the northeast. This field was validated based on the model data VEMOS2009 recommended by SIRGAS. The differences in average velocity for the stations used as input for the calculation of the field were of the order of +0.63 cm/yr, +0.22 cm/yr for the velocity values in latitude and longitude, which is a good determination velocity values and estimating the empirical covariance function necessary for implementing the method of application. Furthermore, the grid used as the basis for interpolation provided differences of about -0.62 cm/yr, -0.12 cm/yr to latitude and longitude. Additionally, the results of this investigation were used as input to an approach in defining the boundary of Panama called block within the country of Costa Rica. The calculation of the components of the Euler pole through a routine program in MatLab and applied to different combinations of points gave no further contributions to the physical definition of this limit. The strategy was simply confirming the difference in the direction of all the velocity vectors and not allowed to reveal more detail revealed a location of this area within the country of Costa Rica.

Truncation error estimation in the Discontinuous Galerkin Spectral Element Method

En esta tesis, el método de estimación de error de truncación conocido como restimation ha sido extendido de esquemas de bajo orden a esquemas de alto orden. La mayoría de los trabajos en la bibliografía utilizan soluciones convergidas en mallas de distinto refinamiento para realizar la estimación. En este trabajo se utiliza una solución en una única malla con distintos órdenes polinómicos. Además, no se requiere que esta solución esté completamente convergida, resultando en el método conocido como quasi-a priori T-estimation. La aproximación quasi-a priori estima el error mientras el residuo del método iterativo no es despreciable. En este trabajo se demuestra que algunas de las hipótesis fundamentales sobre el comportamiento del error, establecidas para métodos de bajo orden, dejan de ser válidas en esquemas de alto orden, haciendo necesaria una revisión completa del comportamiento del error antes de redefinir el algoritmo. Para facilitar esta tarea, en una primera etapa se considera el método conocido como Chebyshev Collocation, limitando la aplicación a geometrías simples. La extensión al método Discontinuouos Galerkin Spectral Element Method presenta dificultades adicionales para la definición precisa y la estimación del error, debidos a la formulación débil, la discretización multidominio y la formulación discontinua. En primer lugar, el análisis se enfoca en leyes de conservación escalares para examinar la precisión de la estimación del error de truncación. Después, la validez del análisis se demuestra para las ecuaciones incompresibles y compresibles de Euler y Navier Stokes. El método de aproximación quasi-a priori r-estimation permite desacoplar las contribuciones superficiales y volumétricas del error de truncación, proveyendo información sobre la anisotropía de las soluciones así como su ratio de convergencia con el orden polinómico. Se demuestra que esta aproximación quasi-a priori produce estimaciones del error de truncación con precisión espectral. ABSTRACT In this thesis, the τ-estimation method to estimate the truncation error is extended from low order to spectral methods. While most works in the literature rely on fully time-converged solutions on grids with different spacing to perform the estimation, only one grid with different polynomial orders is used in this work. Furthermore, a non timeconverged solution is used resulting in the quasi-a priori τ-estimation method. The quasi-a priori approach estimates the error when the residual of the time-iterative method is not negligible. It is shown in this work that some of the fundamental assumptions about error tendency, well established for low order methods, are no longer valid in high order schemes, making necessary a complete revision of the error behavior before redefining the algorithm. To facilitate this task, the Chebyshev Collocation Method is considered as a first step, limiting their application to simple geometries. The extension to the Discontinuous Galerkin Spectral Element Method introduces additional features to the accurate definition and estimation of the error due to the weak formulation, multidomain discretization and the discontinuous formulation. First, the analysis focuses on scalar conservation laws to examine the accuracy of the estimation of the truncation error. Then, the validity of the analysis is shown for the incompressible and compressible Euler and Navier Stokes equations. The developed quasi-a priori τ-estimation method permits one to decouple the interfacial and the interior contributions of the truncation error in the Discontinuous Galerkin Spectral Element Method, and provides information about the anisotropy of the solution, as well as its rate of convergence in polynomial order. It is demonstrated here that this quasi-a priori approach yields a spectrally accurate estimate of the truncation error.