Origin of the gases released from the Acqua Passante and Ermeta wells (Mt. Amiata, central Italy) and possible environmental implications for their closure

The Mt. Amiata volcano (Tuscany, central Italy) hosts the second largest geothermal field of Italy. Its SW and NE sectors are characterized by the presence of several CO2-rich (mayor que95% by vol.) gas discharges. An intense Hg mining activity had taken place from the 19th century up to the end of the ?70s, particularly close to Abbadia San Salvatore, during which two drillings (Acqua Passante and Ermeta) intercepted a CO2-rich gas fertile horizon. The related gases are emitted in the atmosphere since 1938 and 1959, respectively, causing severe concerns for the local air quality. In this work the results of a geochemical and isotopic survey carried out on these gas emissions from March 2009 to January 2014 are presented. CO2 fluxes from both the two wells and soil from an area of about 653,500 m2 located between them were measured. The two wells are emitting up to 15,000, 92 and 8 tons y-1 of CO2, CH4 and H2S, respectively, while the computed soil CO2 output was estimated at 4,311 ton y-1. The spatial distribution of the CO2 soil flux suggests the presence of preferential patterns, indicating sites of higher permeability. Since the local municipality is evaluating the possibility to plug the Ermeta vent, a temporarily closure should first be carried out to test the possible influence of this operation on the diffuse soil degassing of deep-originated CO2 in the surrounding area. This implies that diffuse soil gases should carefully be monitored before proceeding with its definitive closure.

Wave Statistics and Space-time Extremes via Stereo Imaging

We present an analysis of the space-time dynamics of oceanic sea states exploiting stereo imaging techniques. In particular, a novel Wave Acquisition Stereo System (WASS) has been developed and deployed at the oceanographic tower Acqua Alta in the Northern Adriatic Sea, off the Venice coast in Italy. The analysis of WASS video measurements yields accurate estimates of the oceanic sea state dynamics, the associated directional spectra and wave surface statistics that agree well with theoretical models. Finally, we show that a space-time extreme, defined as the expected largest surface wave height over an area, is considerably larger than the maximum crest observed in time at a point, in agreement with theoretical predictions.

Wedges and plate-bandes: mechanical theories after De la Hire

Plate-bandes are straight masonry arches (they are called, also, flat arches or lintel arches). Ideally they have the surfaces of extrados and intrados plane and horizontal. The stones or bricks have radial joints converging usually in one centre. The voussoirs have the form of wedges and in French they are called "claveaux". A plate-bande is, in fact, a lintel made of several stones and the proportions of lintels and plate-bandes are similar. Proportions of plate-bandes, that is the relationship between the thickness t and the span s (t/s)varies, typically between 1/4–1/3 in thick plate-bandes, and is less than 1/20 in the most slender ones. A ratio of circa 1/8 was usual in the 18th Century and follows a simple geometrical rule: the centre form with the intrados an equilateral triangle and the plate-bande should contain an arc of circle. The joints are usually plane, but in some cases present a «rebated» or «stepped» form. Plate-bandes exert an inclined thrust as any masonry arch. This thrust is usually very high and it requires either massive buttresses, or to be built in the middle of thick walls. Master builders and architects have tried since antiquity to calculate the abutment necessary for any arch. A modern architect or engineer will measure the arch thrust in units of force, kN or tons. Traditionally, the thrust has been measured as the size of the buttresses to resist it safely. Old structural rules, then, addressed the design problem establishing a relationship between the span and the depth of the buttress. These were empirical rules, particular for every type of arch or structure in every epoch. Thus, the typical gothic buttress is 1/4 of the vault span, but a Renaissance or baroque barrel vault will need more than 1/3 of the span. A plate-bande would require more than one half of the span; this is precisely the rule cited by the French engineer Gautier, who tried unsuccessfully to justify it by static reasons. They were used, typically, to form the lintels of windows or doors (1-2 m, typically); in Antiquity they were used, also, though rarely, at the gates of city walls or in niches (ca. 2 m, reaching 5.2 m). Plate-bandes may show particular problems: it is not unusual that some sliding of the voussoirs can be observed, particularly in thick plate-bandes. The stepped joints on Fig. 1, left, were used to avoid this problem. There are other «hidden» methods, like iron cramps or the use of stone wedges, etc. In seismic zones these devices were usual. Another problem relates to the deformation; a slight yielding of the abutments, or even the compression of the mortar joints, may lead to some cracking and the descent of the central keystone. Even a tiny descent will convert the original straight line of the intrados in a broken line with a visible «kink» or angle in the middle. Of course, both problems should be avoided. Finally, the wedge form of the voussoirs lead to acute angles in the stones and this can produce partial fractures; this occurs usually at the inferior border of the springers at the abutments. It follows, that to build a successful plate-bande is not an easy matter. Also, the structural study of plate-bandes is far from simple, and mechanics and geometry are related in a particular way. In the present paper we will concentrate on the structural aspects and their constructive consequences, with a historical approach. We will outline the development of structural analysis of plate-bandes from ca. 1700 until today. This brief history has a more than purely academic interest. Different approaches and theories pointed to particular problem, and though the solution given may have been incorrect, the question posed was often pertinent. The paper ends with the application of modern Limit Analysis of Masonry Structures, developed mainly by professor Heyman in the last fifty years. The work aims, also, to give some clues for the actual architect and engineer involved in the analysis or restoration of masonry buildings.

Offshore stereo measurements of gravity waves

Stereo video techniques are effective for estimating the space-time wave dynamics over an area of the ocean. Indeed, a stereo camera view allows retrieval of both spatial and temporal data whose statistical content is richer than that of time series data retrieved from point wave probes. To prove this, we consider an application of the Wave Acquisition Stereo System (WASS) for the analysis of offshore video measurements of gravity waves in the Northern Adriatic Sea. In particular, we deployed WASS at the oceanographic platform Acqua Alta, off the Venice coast, Italy. Three experimental studies were performed, and the overlapping field of view of the acquired stereo images covered an area of approximately 1100 m2. Analysis of the WASS measurements show that the sea surface can be accurately estimated in space and time together, yielding associated directional spectra and wave statistics that agree well with theoretical models. From the observed wavenumber-frequency spectrum one can also predict the vertical profile of the current flow underneath the wave surface. Finally, future improvements of WASS and applications are discussed.

Nuevas arquitecturas de transpondedores de microondas = New transponder architectures at microwave frequencies = Nouvelles architectures des transpondeurs d’hyperfréquences

En la última década, los sistemas de telecomunicación de alta frecuencia han evolucionado tremendamente. Las bandas de frecuencias, los anchos de banda del usuario, las técnicas de modulación y otras características eléctricas están en constante cambio de acuerdo a la evolución de la tecnología y la aparición de nuevas aplicaciones. Las arquitecturas de los transceptores modernos son diferentes de las tradicionales. Muchas de las funciones convencionalmente realizadas por circuitos analógicos han sido asignadas gradualmente a procesadores digitales de señal, de esta manera, las fronteras entre la banda base y las funcionalidades de RF se difuminan. Además, los transceptores inalámbricos digitales modernos son capaces de soportar protocolos de datos de alta velocidad, por lo que emplean una elevada escala de integración para muchos de los subsistemas que componen las diferentes etapas. Uno de los objetivos de este trabajo de investigación es realizar un estudio de las nuevas configuraciones en el desarrollo de demostradores de radiofrecuencia (un receptor y un transmisor) y transpondedores para fines de comunicaciones y militares, respectivamente. Algunos trabajos se han llevado a cabo en el marco del proyecto TECRAIL, donde se ha implementado un demostrador de la capa física LTE para evaluar la viabilidad del estándar LTE en el entorno ferroviario. En el ámbito militar y asociado al proyecto de calibración de radares (CALRADAR), se ha efectuado una actividad importante en el campo de la calibración de radares balísticos Doppler donde se ha analizado cuidadosamente su precisión y se ha desarrollado la unidad generadora de Doppler de un patrón electrónico para la calibración de estos radares. Dicha unidad Doppler es la responsable de la elevada resolución en frecuencia del generador de “blancos” radar construido. Por otro lado, se ha elaborado un análisis completo de las incertidumbres del sistema para optimizar el proceso de calibración. En una segunda fase se han propuesto soluciones en el desarrollo de dispositivos electro-ópticos para aplicaciones de comunicaciones. Estos dispositivos son considerados, debido a sus ventajas, tecnologías de soporte para futuros dispositivos y subsistemas de RF/microondas. Algunas demandas de radio definida por software podrían cubrirse aplicando nuevos conceptos de circuitos sintonizables mediante parámetros programables de un modo dinámico. También se ha realizado una contribución relacionada con el diseño de filtros paso banda con topología “Hairpin”, los cuales son compactos y se pueden integrar fácilmente en circuitos de microondas en una amplia gama de aplicaciones destinadas a las comunicaciones y a los sistemas militares. Como importante aportación final, se ha presentado una propuesta para ecualizar y mejorar las transmisiones de señales discretas de temporización entre los TRMs y otras unidades de procesamiento, en el satélite de última generación SEOSAR/PAZ. Tras un análisis exhaustivo, se ha obtenido la configuración óptima de los buses de transmisión de datos de alta velocidad basadas en una red de transceptores. ABSTRACT In the last decade, high-frequency telecommunications systems have extremely evolved. Frequency bands, user bandwidths, modulation techniques and other electrical characteristics of these systems are constantly changing following to the evolution of technology and the emergence of new applications. The architectures of modern transceivers are different from the traditional ones. Many of the functions conventionally performed by analog circuitry have gradually been assigned to digital signal processors. In this way, boundaries between baseband and RF functionalities are diffused. The design of modern digital wireless transceivers are capable of supporting high-speed data protocols. Therefore, a high integration scale is required for many of the components in the block chain. One of the goals of this research work is to investigate new configurations in the development of RF demonstrators (a receiver and a transmitter) and transponders for communications and military purposes, respectively. A LTE physical layer demonstrator has been implemented to assess the viability of LTE in railway scenario under the framework of the TECRAIL project. An important activity, related to the CALRADAR project, for the calibration of Doppler radars with extremely high precision has been performed. The contribution is the Doppler unit of the radar target generator developed that reveals a high frequency resolution. In order to assure the accuracy of radar calibration process, a complete analysis of the uncertainty in the above mentioned procedure has been carried out. Another important research topic has been the development of photonic devices that are considered enabling technologies for future RF and microwave devices and subsystems. Some Software Defined Radio demands are addressed by the proposed novel circuit concepts based on photonically tunable elements with dynamically programmable parameters. A small contribution has been made in the field of Hairpin-line bandpass filters. These filters are compact and can also be easily integrated into microwave circuits finding a wide range of applications in communication and military systems. In this research field, the contributions made have been the improvements in the design and the simulations of wideband filters. Finally, an important proposal to balance and enhance transmissions of discrete timing signals between TRMs and other processing units into the state of the art SEOSAR/PAZ Satellite has been carried out obtaining the optimal configuration of the high-speed data transmission buses based on a transceiver network. RÉSUMÉ Les systèmes d'hyperfréquence dédiés aux télécommunications ont beaucoup évolué dans la dernière décennie. Les bandes de fréquences, les bandes passantes par utilisateur, les techniques de modulation et d'autres caractéristiques électriques sont en constant changement en fonction de l'évolution des technologies et l'émergence de nouvelles applications. Les architectures modernes des transcepteurs sont différentes des traditionnelles. Un grand nombre d’opérations normalement effectuées par les circuits analogiques a été progressivement alloué à des processeurs de signaux numériques. Ainsi, les frontières entre la bande de base et la fonctionnalité RF sont floues. Les transcepteurs sans fils numériques modernes sont capables de transférer des données à haute vitesse selon les différents protocoles de communication utilisés. C'est pour cette raison qu’un niveau élevé d'intégration est nécessaire pour un grand nombre de composants qui constitue les différentes étapes des systèmes. L'un des objectifs de cette recherche est d'étudier les nouvelles configurations dans le développement des démonstrateurs RF (récepteur et émetteur) et des transpondeurs à des fins militaire et de communication. Certains travaux ont été réalisés dans le cadre du projet TECRAIL, où un démonstrateur de la couche physique LTE a été mis en place pour évaluer la faisabilité de la norme LTE dans l'environnement ferroviaire. Une contribution importante, liée au projet CALRADAR, est proposée dans le domaine des systèmes d’étalonnage de radar Doppler de haute précision. Cette contribution est le module Doppler de génération d’hyperfréquence intégré dans le système électronique de génération de cibles radar virtuelles que présente une résolution de fréquence très élevée. Une analyse complète de l'incertitude dans l'étalonnage des radars Doppler a été effectuée, afin d'assurer la précision du calibrage. La conception et la mise en oeuvre de quelques dispositifs photoniques sont un autre sujet important du travail de recherche présenté dans cette thèse. De tels dispositifs sont considérés comme étant des technologies habilitantes clés pour les futurs dispositifs et sous-systèmes RF et micro-ondes grâce à leurs avantages. Certaines demandes de radio définies par logiciel pourraient être supportées par nouveaux concepts de circuits basés sur des éléments dynamiquement programmables en utilisant des paramètres ajustables. Une petite contribution a été apportée pour améliorer la conception et les simulations des filtres passe-bande Hairpin à large bande. Ces filtres sont compacts et peuvent également être intégrés dans des circuits à micro-ondes compatibles avec un large éventail d'applications dans les systèmes militaires et de communication. Finalement, une proposition a été effectuée visant à équilibrer et améliorer la transmission des signaux discrets de synchronisation entre les TRMs et d'autres unités de traitement dans le satellite SEOSAR/PAZ de dernière génération et permettant l’obtention de la configuration optimale des bus de transmission de données à grande vitesse basés sur un réseau de transcepteurs.