Experimental Model to estimate shading losses on PV arrays

This paper presents a simple mathematical model to estimateshadinglosses on PVarrays. The model is applied directly to power calculations, without the need to consider the whole current–voltage curve. This allows the model to be used with common yield estimation software. The model takes into account both the shaded fraction of the array area and the number of blocks (a group of solar cells protected by a bypass diode) affected by shade. The results of an experimental testing campaign on several shaded PVarrays to check the validity of model are also reported.

Estudio de la funcionalización de secciones eficaces de celda en multigrupos para cálculos best-estimate 3D pin-by-pin de núcleos PWR

Uno de los objetivos del Proyecto europeo NURISP (NUclear Reactor Integrated Platform) del 7º Programa Marco es avanzar en la simulación de reactores de agua ligera mediante el acoplamiento de códigos best-estimate que profundicen en la física de núcleo, termohidráulica bifásica y comportamiento del combustible [1]. Uno de estos códigos es COBAYA3, código de difusión 3D en multigrupos pin-by-pin desarrollado en la UPM, que requiere de librerías de secciones eficaces homogeneizadas a nivel de la barrita de combustible.

Análisis de parámetros de fendas para la estimación de las propiedades mecánicas de vigas de madera de Pinus sylvestris L. Analysis of parameters for assessing drying fissures to estimate their influence on the mechanical properties of Pinus sylvestris L. wooden beams

El principal objetivo de este estudio es evaluar la influencia de las fendas de secado en las propiedades mecánicas de vigas de madera. Para esto, se utilizan 40 vigas de Pino silvestre (Pinus sylvestris L) de 4200 mm de longitud y 150x200 mm de sección que fueron ensayadas según norma EN 408. Las fendas se registran detalladamente atendiendo a su longitud y posición en cada cara de la viga, y midiendo el espesor y la profundidad cada 100mm a lo largo de la viga. Solo el 10% de la muestra es rechazada por las fendas, según los criterios establecidos por la norma española de clasificación visual UNE 56544. Para evaluar la influencia de las fendas en las propiedades mecánicas, se usan tres parámetros globales basados en el área, el volumen o la profundad de la fenda, y dos locales basados en la profundidad máxima y la profundidad en la zona de rotura. Además se determina la densidad de las piezas. Estos parámetros se comparan con las propiedades mecánicas (tensión de rotura, módulo de elasticidad y energía de rotura) y se encuentra escasa relación entre ellos. Las mejores correlaciones se encuentran entre los parámetros relacionados con la profundidad de las fendas, tanto con el módulo de elasticidad como con la tensión de rotura. The aim of this study is the evaluation of the influence of drying fissures on the mechanical properties of timber beams. For that purpose, 40 sawn timber pieces of Scots pine (Pinus sylvestris L.) with 150x200 mm in cross-section and 4200 mm in length have been tested according to EN 408, obtaining MOR and MOE. The fissures were registered in detail measuring their length and position in each face of the beam, and the thickness and depth every 100 mm in length. Only 10 % of the pieces were rejected because fissures, according to UNE 56544 Spanish visual grading standard. To evaluate the influence of fissures in mechanical properties three global parameters: Fissures Area Ratio or ratio between the area occupied by fissures and the total area in the neutral axis plane of the beam; Fissures Volume Ratio or ratio between volume of fissures and the total volume of the beam; Fissures Average Depth and two local parameters were used: Fissures Maximum Depth in the beam, and Fissures Depth in the broken zone of the beam. Also the density of the beams was registered. These parameters were compared with mechanical properties (tensile strength, elasticity modulus, and rupture energy) and the relationship between them had not been founded. The best relationship was founded between the elasticity modulus y the tensile strength with the parameters which included the depth of the fissures.

In situ acoustic methods to estimate the physical and mechanical aging of oriented strand board

Following the success achieved in previous research projects usin non-destructive methods to estimate the physical and mechanical aging of particle and fibre boards, this paper studies the relationships between aging, physical and mechanical changes, using non-destructive measurements of oriented strand board (OSB). 184 pieces of OSB board from a French source were tested to analyze its actual physical and mechanical properties. The same properties were estimated using acoustic non-destructive methods (ultrasound and stress wave velocity) during a physical laboratory aging test. Measurements were recorded of propagation wave velocity with the sensors aligned, edge to edge, and forming an angle of 45 degrees, with both sensors on the same face of the board. This is because aligned measures are not possible on site. The velocity results are always higher in 45 degree measurements. Given the results of statistical analysis, it can be concluded that there is a strong relationship between acoustic measurements and the decline in physical and mechanical properties of the panels due to aging. The authors propose several models to estimate the physical and mechanical properties of board, as well as their degree of aging. The best results are obtained using ultrasound, although the difference in comparison with the stress wave method is not very significant. A reliable prediction of the degree of deterioration (aging) of board is presented.

Non-destructive methods to estimate physical aging of plywood

This paper studies the relationship between aging, physical changes and the results of non-destructive testing of plywood. 176 pieces of plywood were tested to analyze their actual and estimated density using non-destructive methods (screw withdrawal force and ultrasound wave velocity) during a laboratory aging test. From the results of statistical analysis it can be concluded that there is a strong relationship between the non-destructive measurements carried out, and the decline in the physical properties of the panels due to aging. The authors propose several models to estimate board density. The best results are obtained with ultrasound. A reliable prediction of the degree of deterioration (aging) of board is presented.

Experimental model to estimate shading losses on PV arrays

This paper presents a simple mathematical model to estimate shading losses on PV arrays. The model is applied directly to power calculations, without the need to consider the whole current–voltage curve. This allows the model to be used with common yield estimation software. The model takes into account both the shaded fraction of the array area and the number of blocks (a group of solar cells protected by a bypass diode) affected by shade. The results of an experimental testing campaign on several shaded PV arrays to check the validity of model are also reported.

Tanque de almacenamiento de GNL para la ampliación de la planta de regasificación de Barcelona

ENAGAS tiene la intención de ampliar el Terminal de Regasificación de GNL que tiene en el puerto de Barcelona. El presente Proyecto Básico define las instalaciones de uno de los Tanques de almacenamiento de GNL que se van a construir dentro del Alcance de dicha ampliación, con el suficiente detalle como para permitir a ENAGAS acometer las tareas previas a la ejecución del proyecto, a saber: 1. Planificar y presupuestar la fase de ejecución 2. Solicitar los Permisos y Autorizaciones necesarias de los Organismos competentes 3. Lanzar la Petición de Ofertas para el concurso llave en mano del EPC. Los trabajos de Ingeniería contenidos en el Proyecto Básico son los siguientes: Antecedentes y Datos básicos, Criterios de diseño, Descripción de instalaciones, Cálculos estructurales, Planos del Tanque de GNL, Definición de equipos y materiales a utilizar, Plan de ejecución del proyecto, Especificaciones técnicas para Ingeniería, Compras y Construcción, Paquete para Petición de Ofertas del EPC, Condiciones técnicas particulares, Programa de ejecución y Presupuesto de inversiones. ABSTRACT ENAGAS is expanding its LNG Regasification Terminal located in Barcelona Port (Spain). This Document reports the Front End Engineering and Design (FEED) works undertaken in relation to one of the LNG Storage Tanks to be built within the scope of that expansion. The Project FEED hereby presented comprehensively defines the LNG Storage Tank so as to allow ENAGAS to perform next stages of the Works, namely: 1. Plan and budget the Project Execution phase 2. Request Regulatory authorizations 3. Invite Contractors to bid for the LNG Tank EPC. Main components of the FEED Document contents are as follow:Background and Basic Data, Design Criteria, Description of LNG Tank elements, Engineering Calculations, LNG Tank Drawings, Equipment and Materials definition, Project Execution Plan (PEP), Technical Conditions, EPC Invitation to Tender (ITT) package, Execution Schedule and Cost Estimate.

A simulation method to estimate closing forces in car-sealing rubber elements

The door-closing process can reinforce the impression of a solid, rock-proof, car body or of a rather cheap, flimsy vehicle. As there are no real prototypes during rubber profile bidding-out stages, engineers need to carry out non-linear numerical simulations that involve complex phenomena as well as static and dynamic loads for several profile candidates. This paper presents a structured virtual design tool based on FEM, including constitutive laws and incompressibility constraints allowing to predict more realistically the final closing forces and even to estimate sealing overpressure as an additional guarantee of noise insulation. Comparisons with results of physical tests are performed.