Wheel-Rail Contact Forces in High-Speed Simply Supported Bridges at Resonance

The response of high-speed bridges at resonance, particularly under flexural vibrations, constitutes a subject of research for many scientists and engineers at the moment. The topic is of great interest because, as a matter of fact, such kind of behaviour is not unlikely to happen due to the elevated operating speeds of modern rains, which in many cases are equal to or even exceed 300 km/h ( [1,2]). The present paper addresses the subject of the evolution of the wheel-rail contact forces during resonance situations in simply supported bridges. Based on a dimensionless formulation of the equations of motion presented in [4], very similar to the one introduced by Klasztorny and Langer in [3], a parametric study is conducted and the contact forces in realistic situations analysed in detail. The effects of rail and wheel irregularities are not included in the model. The bridge is idealised as an Euler-Bernoulli beam, while the train is simulated by a system consisting of rigid bodies, springs and dampers. The situations such that a severe reduction of the contact force could take place are identified and compared with typical situations in actual bridges. To this end, the simply supported bridge is excited at resonace by means of a theoretical train consisting of 15 equidistant axles. The mechanical characteristics of all axles (unsprung mass, semi-sprung mass, and primary suspension system) are identical. This theoretical train permits the identification of the key parameters having an influence on the wheel-rail contact forces. In addition, a real case of a 17.5 m bridges traversed by the Eurostar train is analysed and checked against the theoretical results. The influence of three fundamental parameters is investigated in great detail: a) the ratio of the fundamental frequency of the bridge and natural frequency of the primary suspension of the vehicle; b) the ratio of the total mass of the bridge and the semi-sprung mass of the vehicle and c) the ratio between the length of the bridge and the characteristic distance between consecutive axles. The main conclusions derived from the investigation are: The wheel-rail contact forces undergo oscillations during the passage of the axles over the bridge. During resonance, these oscillations are more severe for the rear wheels than for the front ones. If denotes the span of a simply supported bridge, and the characteristic distance between consecutive groups of loads, the lower the value of , the greater the oscillations of the contact forces at resonance. For or greater, no likelihood of loss of wheel-rail contact has been detected. The ratio between the frequency of the primary suspension of the vehicle and the fundamental frequency of the bridge is denoted by (frequency ratio), and the ratio of the semi-sprung mass of the vehicle (mass of the bogie) and the total mass of the bridge is denoted by (mass ratio). For any given frequency ratio, the greater the mass ratio, the greater the oscillations of the contact forces at resonance. The oscillations of the contact forces at resonance, and therefore the likelihood of loss of wheel-rail contact, present a minimum for approximately between 0.5 and 1. For lower or higher values of the frequency ratio the oscillations of the contact forces increase. Neglecting the possible effects of torsional vibrations, the metal or composite bridges with a low linear mass have been found to be the ones where the contact forces may suffer the most severe oscillations. If single-track, simply supported, composite or metal bridges were used in high-speed lines, and damping ratios below 1% were expected, the minimum contact forces at resonance could drop to dangerous values. Nevertheless, this kind of structures is very unusual in modern high-speed railway lines.

The Dynamics of High-Speed Railway Bridges: A Review of Design Issues and New Research for Lateral Dynamics

The dynamic effects of high-speed trains on viaducts are important issues for the design of the structures, as well as for the consideration of safe running conditions for the trains. In this work we start by reviewing the relevance of some basic design aspects. The significance of impact factor envelopes for moving loads is considered first. Resonance which may be achieved for high-speed trains requires dynamic analysis, for which some key aspects are discussed. The relevance of performing a longitudinal distribution of axle loads, the number of modes taken in analysis, and the consideration of vehicle-structure interaction are discussed with representative examples. The lateral dynamic effects of running trains on bridges is of importance for laterally compliant viaducts, such as some very tall structures erected in new high-speed lines. The relevance of this study is mainly for the safety of the traffic, considering both internal actions such as the hunting motion as well as external actions such as wind or earthquakes [1]. These studies require three-dimensional dynamic coupled vehicle-bridge models, and consideration of wheel to rail contact, a phenomenon which is complex and costly to model in detail. We describe here a fully nonlinear coupled model, described in absolute coordinates and incorporated into a commercial finite element framework [2]. The wheel-rail contact has been considered using a FastSim algorithm which provides a compromise between accuracy and computational cost, and captures the main nonlinear response of the contact interface. Two applications are presented, firstly to a vehicle subject to a strong wind gust traversing a bridge, showing the relevance of the nonlinear wheel-rail contact model as well as the dynamic interaction between bridge and vehicle. The second application is to a real HS viaduct with a long continuous deck and tall piers and high lateral compliance [3]. The results show the safety of the traffic as well as the importance of considering features such as track alignment irregularities.

Coupled models for the dynamics of bridges under high-speed rail traffic

The dynamic effects of high-speed trains on viaducts are important issues for the design of the structures, as well as for determining safe running conditions of trains. In this work we start by reviewing the relevance of some basic moving load models for the dynamic action of vertical traffic loads. The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require 3D coupled vehicle-bridge models and consideration of wheel to rail contact. We describe here a fully nonlinear coupled model, formulated in absolute coordinates and incorporated into a commercial finite element framework. An application example is presented for a vehicle subject to a strong wind gust traversing a bridge, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle.

Analysis of lateral dynamics of railway vehicles on viaducts with coupled models

The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require 3D coupled vehicle-bridge models, and consideration of wheel to rail contact, a phenomenon which is complex and costly to model in detail. We describe here a fully nonlinear coupled model, described in absolute coordinates and incorporated into a commercial finite element framework. Two applications are presented, firstly to a vehicle subject to a strong wind gust traversing a br idge, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle. The second application is to a real viaduct in a high-speed line, with a long continuous deck and tall piers with high lateral compliance. The results show the safety of the traffic as well as the relevance of considering the wind action and the nonlinear response.

Influence of the track quality and of the properties of the wheel rail rolling contact on vehicle dynamics

This work describes an analytical approach to determine what degree of accuracy is required in the definition of the rail vehicle models used for dynamic simulations. This way it would be possible to know in advance how the results of simulations may be altered due to the existence of errors in the creation of rolling stock models, whilst also identifying their critical parameters. This would make it possible to maximize the time available to enhance dynamic analysis and focus efforts on factors that are strictly necessary.In particular, the parameters related both to the track quality and to the rolling contact were considered in this study. With this aim, a sensitivity analysis was performed to assess their influence on the vehicle dynamic behaviour. To do this, 72 dynamic simulations were performed modifying, one at a time, the track quality, the wheel-rail friction coefficient and the equivalent conicity of both new and worn wheels. Three values were assigned to each parameter, and two wear states were considered for each type of wheel, one for new wheels and another one for reprofiled wheels.After processing the results of these simulations, it was concluded that all the parameters considered show very high influence, though the friction coefficient shows the highest influence. Therefore, it is recommended to undertake any future simulation job with measured track geometry and track irregularities, measured wheel profiles and normative values of wheel-rail friction coefficient.

Dynamic Analysis of high Speed Railway Traffic Loads on Ballasted Track

This paper reports the studies carried out to develop and calibrate the optimal models for the objectives of this work. In particular, quarter bogie model for vehicle, rail-wheel contact with Lagrangian multiplier method, 2D spatial discretization were selected as the optimal decisions. Furthermore, the 3D model of coupled vehicle-track also has been developed to contrast the results obtained in the 2D model. The calculations were carried out in the time domain and envelopes of relevant results were obtained for several track profiles and speed ranges. Distributed elevation irregularities were generated based on power spectral density (PSD) distributions. The results obtained include the wheel-rail contact forces, forces transmitted to the bogie by primary suspension. The latter loads are relevant for the purpose of evaluating the performance of the infrastructure

Nonlinear models for lateral dynamics of railway vehicles on bridges subject to wind action

The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require threedimensional coupled vehicle-bridge models, wheree consideration of wheel to rail contact is a key aspect. Furthermore, an adequate evaluation of safety of rail traffic requires nonlinear models. A nonlinear coupled model is proposed here for vehicle-structure vertical and lateral dynamics. Vehicles are considered as fully three-dimensional multibody systems including gyroscopic terms and large rotation effects. The bridge structure is modeled by means of finite elements which may be of beam, shell or continuum type and may include geometric or material nonlinearities. The track geometry includes distributed track alignment irregularities. Both subsystems (bridge and vehicles) are described with coordinates in absolute reference frames, as opposed to alternative approaches which describe the multibody system with coordinates relative to the base bridge motion. The wheelrail contact employed is a semi-Hertzian model based on realistic wheel-rail profiles. It allows a detailed geometrical description of the contact patch under each wheel including multiple-point contact, flange contact and uplift. Normal and tangential stresses in each contact are integrated at each time-step to obtain the resultant contact forces. The models have been implemented within an existing finite element analysis software with multibody capabilities, Abaqus (Simulia Ltd., 2010). Further details of the model are presented in Antolín et al. (2012). Representative applications are presented for railway vehicles under lateral wind action on laterally compliant viaducts, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle.

Efectos dinámicos laterales en vehículos y puentes ferroviarios sometidos a la acción de vientos transversales

En las últimas décadas el aumento de la velocidad y la disminución del peso de los vehículos ferroviarios de alta velocidad ha provocado que aumente su riesgo de vuelco. Además, las exigencias de los trazados de las líneas exige en ocasiones la construcción de viaductos muy altos situados en zonas expuestas a fuertes vientos. Esta combinación puede poner en peligro la seguridad de la circulación. En esta tesis doctoral se estudian los efectos dinámicos que aparecen en los vehículos ferroviarios cuando circulan sobre viaductos en presencia de vientos transversales. Para ello se han desarrollado e implementado una serie de modelos numéricos que permiten estudiar estos efectos de una forma realista y general. Los modelos desarrollados permiten analizar la interacción dinámica tridimensional tren-estructura, formulada mediante coordenadas absolutas en un sistema de referencia inercial, en un contexto de elementos _nitos no lineales. Mediante estos modelos se pueden estudiar de forma realista casos extremos como el vuelco o descarrilamiento de los vehículos. Han sido implementados en Abaqus, utilizando sus capacidades para resolver sistemas multi-cuerpo para el vehículo y elementos finitos para la estructura. La interacción entre el vehículo y la estructura se establece a través del contacto entre rueda y carril. Para ello, se han desarrollado una restricción, que permite establecer la relación cinemática entre el eje ferroviario y la vía, teniendo en cuenta los posibles defectos geométricos de la vía; y un modelo de contacto rueda-carril para establecer la interacción entre el vehículo y la estructura. Las principales características del modelo de contacto son: considera la geometría real de ambos cuerpos de forma tridimensional; permite resolver situaciones en las que el contacto entre rueda y carril se da en más de una zona a la vez; y permite utilizar distintas formulaciones para el cálculo de la tensión tangencial entre ambos cuerpos. Además, se ha desarrollado una metodología para determinar, a partir de formulaciones estocásticas, las historias temporales de cargas aerodinámicas debidas al viento turbulento en estructuras grandes y con pilas altas y flexibles. Esta metodología tiene cuenta la variabilidad espacial de la velocidad de viento, considerando la correlación entre los distintos puntos; considera las componentes de la velocidad del viento en tres dimensiones; y permite el cálculo de la velocidad de viento incidente sobre los vehículos que atraviesan la estructura. La metodología desarrollada en este trabajo ha sido implementada, validada y se ha aplicado a un caso concreto en el que se ha estudiado la respuesta de un tren de alta velocidad, similar al Siemens Velaro, circulando sobre el viaducto del río Ulla en presencia viento cruzado. En este estudio se ha analizado la seguridad y el confort de la circulación y la respuesta dinámica de la estructura cuando el tren cruza el viaducto. During the last decades the increase of the speed and the reduction of the weight of high-speed railway vehicles has led to a rise of the overturn risk. In addition, the design requests of the railway lines require some times the construction of very tall viaducts in strong wind areas. This combination may endanger the traffic safety. In this doctoral thesis the dynamic effects that appear in the railway vehicles when crossing viaducts under strong winds are studied. For this purpose it has been developed and implemented numerical models for studying these effects in a realistic and general way. The developed models allow to analyze the train-structure three-dimensional dynamic interaction, that is formulated by using absolute coordinates in an inertial reference frame within a non-linear finite element framework. By means of these models it is possible to study in a realistic way extreme situations such vehicle overturn or derailment. They have been implemented for Abaqus, by using its capabilities for solving multi-body systems for the vehicle and finite elements for the structure. The interaction between the vehicle and the structure is established through the wheel-rail contact. For this purpose, a constraint has been developed. It allows to establish the kinematic relationship between the railway wheelset and the track, taking into account the track irregularities. In addition, a wheel-rail contact model for establishing the interaction of the vehicle and the structure has been developed. The main features of the contact model are: it considers the real geometry During the last decades the increase of the speed and the reduction of the weight of high-peed railway vehicles has led to a rise of the overturn risk. In addition, the design requests of the railway lines require some times the construction of very tall viaducts in strong wind areas. This combination may endanger the traffic safety. In this doctoral thesis the dynamic effects that appear in the railway vehicles when crossing viaducts under strong winds are studied. For this purpose it has been developed and implemented numerical models for studying these effects in a realistic and general way. The developed models allow to analyze the train-structure three-dimensional dynamic interaction, that is formulated by using absolute coordinates in an inertial reference frame within a non-linear finite element framework. By means of these models it is possible to study in a realistic way extreme situations such vehicle overturn or derailment. They have been implemented for Abaqus, by using its capabilities for solving multi-body systems for the vehicle and finite elements for the structure. The interaction between the vehicle and the structure is established through the wheel-rail contact. For this purpose, a constraint has been developed. It allows to establish the kinematic relationship between the railway wheelset and the track, taking into account the track irregularities. In addition, a wheel-rail contact model for establishing the interaction of the vehicle and the structure has been developed. The main features of the contact model are: it considers the real geometry

Models for Lateral Dynamic Interaction of High-Speed Trains and Bridges

In this work a methodology for analysing the lateral coupled behavior of large viaducts and high-speed trains is proposed. The finite element method is used for the structure, multibody techniques are applied for vehicles and the interaction between them is established introducing wheel-rail nonlinear contact forces. This methodology is applied for the analysis of the railway viaduct of the R´ıo Barbantino, which is a very long and tall bridge in the north-west spanish high-speed line.

Efectos dinámicos debidos al tráfico de ferrocarril sobre la infraestructura de vía y las estructuras

La vía tradicional sobre balasto sigue siendo una selección para las líneas de alta velocidad a pesar de los problemas técnicos y la prestación del funcionamiento. El problema de la vía sobre balasto es el proceso continuo del deterioro de éste debido a las cargas asociadas al tráfico ferroviario. En consecuencia es imprescindible un mantenimiento continuado para mantener un alineamiento adecuado de la vía. Por eso se surge la necesidad de comprender mejor el mecanismo involucrado en el deterioro de la vía y los factores claves que rigen su progresión a lo largo de ciclos de carga con el fin de reducir los costos del mantenimiento de la vía y mejorar el diseño de las nuevas vías. La presente tesis intenta por un lado desarrollar los modelos más adecuados y eficientes del vehículo y de la vía para los cálculos de los efectos dinámicos debido al tráfico de ferrocarril sobre la infraestructura de la vía sobre balasto, y por otro evaluar estos efectos dinámicos sobre el deterioro de la vía sobre balasto a largo plazo, empleando un adecuado modelo de predicción del deterioro de la misma. Se incluye en el trabajo una recopilación del estado del arte en lo referente a la dinámica de la vía, a la modelización del vehículo, de la vía y de la interacción entre ambos. También se hace un repaso al deterioro de la vía y los factores que influyen en su proceso. Para la primera línea de investigación de esta tesis, se han desarrollado los diferentes modelos del vehículo y de la vía y la modelización de la interacción entre ambos para los cálculos dinámicos en dos y tres dimensiones. En la interacción vehículo-vía, se ha empleado la formulación de contacto nodo-superficie para establecer la identificación de las superficies en contacto y el método de los multiplicadores de Lagrange para imponer las restricciones de contacto. El modelo de interacción se ha contrastado con los casos reportados en la literatura. Teniendo en cuenta el contacto no lineal entre rueda-carril y los perfiles de irregularidades distribuidas de la vía, se han evaluado y comparado los efectos dinámicos sobre el sistema vehículo-vía en la interacción de ambos, para distintas velocidades de circulación del vehículo, en los aspectos como la vibración del vehículo, fuerza de contacto, fuerza transmitida en los railpads, la vibración del carril. También se hace un estudio de la influencia de las propiedades de los componentes de la vía en la respuesta dinámica del sistema vehículo-vía. Se ha desarrollado el modelo del asiento de la vía que consiste en la implementación del modelo de acumulación de Bochum y del modelo de hipoplasticidad en la subrutina del usuario \UMAT" del programa ABAQUS. La implementación numérica ha sido comprobado al comparar los resultados de las simulaciones numéricas con los reportados en la literatura. Se ha evaluado la calidad geométrica de la vía sobre balasto de los tramos de estudio con datos reales de la auscultación proporcionados por ADIF (2012). Se ha propuesto una metodología de simulación, empleando el modelo de asiento, para reproducir el deterioro de la geometría de la vía. Se usan los perfiles de la nivelación longitudinal de la auscultación como perfiles de irregularidades iniciales de la vía en las simulaciones numéricas. También se evalúa la influencia de la velocidad de circulación sobre el deterioro de la vía. The traditional ballast track structures are still being used in high speed railways lines with success, however technical problems or performance features have led to ballast track solution in some cases. The considerable maintenance work is needed for ballasted tracks due to the track deterioration. Therefore it is very important to understand the mechanism of track deterioration and to predict the track settlement or track irregularity growth rate in order to reduce track maintenance costs and enable new track structures to be designed. This thesis attempts to develop the most adequate and efficient models for calculation of dynamic track load effects on railways track infrastructure, and to evaluate these dynamic effects on the track settlement, using a track settlement prediction model, which consists of the vehicle/track dynamic model previously selected and a track settlement law. A revision of the state of the knowledge regarding the track dynamics, the modelling of the vehicle, the track and the interaction between them is included. An overview related to the track deterioration and the factors influencing the track settlement is also done. For the first research of this thesis, the different models of vehicle, track and the modelling of the interaction between both have been developed. In the vehicle-track interaction, the node-surface contact formulation to establish the identification of the surfaces in contact and the Lagrange multipliers method to enforce contact constraint are used. The interaction model has been verified by contrast with some benchmarks reported in the literature. Considering the nonlinear contact between wheel-rail and the track irregularities, the dynamic effects on the vehicle-track system have been evaluated and compared, for different speeds of the vehicle, in aspects as vehicle vibration, contact force, force transmitted in railpads, rail vibration. A study of the influence of the properties of the track components on the the dynamic response of the vehicle-track system has been done. The track settlement model is developed that consist of the Bochum accumulation model and the hipoplasticity model in the user subroutine \UMAT" of the program ABAQUS. The numerical implementation has been verified by comparing the numerical results with those reported in the literature. The geometric quality of the ballast track has been evaluated with real data of auscultation provided by ADIF (2012). The simulation methodology has been proposed, using the settlement model for the ballast material, to reproduce the deterioration of the track geometry. The profiles of the longitudinal level of the auscultation is used as initial profiles of the track irregularities in the numerical simulation. The influence of the running speed on the track deterioration is also investigated.

Metodología para la evaluación de la consistencia del trazado de carreteras interurbanas de dos carriles

La consistencia del trazado puede interpretarse como la relación entre las características geométricas de una carretera y lo que espera encontrar el conductor que circula por ella. Si hay una correspondencia entre estos dos aspectos, la conducción puede hacerse de modo continuo, sin sobresaltos, lo que incide favorablemente sobre la seguridad en la circulación. Si bien hay una serie de recomendaciones desde el punto de vista geométrico para obtener trazados consistentes, esto no siempre se logra, y sólo en los últimos años se ha iniciado el estudio de metodologías para evaluar ésto, tanto en vías existentes como en vías proyectadas. La mayor parte de estas metodologías sólo considera el trazado en planta, olvidándose del trazado en alzado y de la coordinación entre los mismos. En esta Tesis doctoral se ha desarrollado una metodología para evaluar la consistencia del trazado en carreteras interurbanas de dos carriles que considera dichos aspectos. Para ello, se hizo un análisis exhaustivo de los índices de trazado, los cuales evalúan las características geométricas en planta y en alzado. Los índices se correlacionaron con la accidentalidad, para determinar cuál de ellos tiene mayor incidencia, encontrándose que es el cambio de curvatura vertical (VCCR); a este índice se le estableció un rango de calificación. Como elemento de evaluación complementario de análisis se seleccionó el perfil de velocidades de operación, procedimiento que ha sido probado en diferentes investigaciones, y del cual se desarrolló un modelo aplicado a Colombia. Para la coordinación de trazados en planta y alzado se evaluaron diferentes combinaciones geométricas, algunas de las cuales generaron reapariciones del trazado. Se ha definido un nuevo índice (Irt) que permite determinar numéricamente la posibilidad de que se presente esta situación, indeseable desde el punto de vista de la seguridad vial. La combinación de estos tres elementos permite una evaluación integral de los diferentes aspectos que inciden sobre la consistencia del trazado de una carretera. La metodología desarrollada se aplicó en el estudio de consistencia del trazado en algunas carreteras españolas y colombianas, ubicadas en distintos tipos de terreno. ABSTRACT Geometric Design Consistency can be defined as the relationship between the geometric characteristics of a road and what the driver expects to find when driving. If there is a correspondence between these two aspects, driving is smoother and unexpected events are minimized, which increases traffic safety conditions. Although from the geometric point of view there are several recommendations to ensure consistent designs, this is not always successfully applied. The study of methods to evaluate design consistency in existing and future routes has only begun in recent years. Most existing methods only consider the horizontal alignment of the road and overlook both the vertical alignment and the coordination that must exist between the vertical and the horizontal. The present Doctoral Thesis proposes a method to evaluate the geometric design consistency of a two-lane rural highway which considers all three of these aspects: the horizontal alignment, the vertical alignment and the coordination that must exist between them. In order to achieve this, several different alignment indices, that evaluate horizontal and vertical geometric characteristics, were thoroughly analyzed to determine their correlation with traffic accidents. The Vertical Curvature Change Rate (VCCR) index showed the highest correlation, and rating thresholds for this index have been established. To complement the evaluation, the operating speed profile, was chosen. This procedure has been extensively tested by several researchers. An operating speed prediction model adapted to Colombia was developed. To study the coordination between the horizontal and the vertical alignments of the road, several geometric combinations of the two were used. Some of these combinations generate undesirable losses of visibility. For this reason, a new index (Irt) was defined to numerically detect those cases, which are undesirable from the point of view of traffic safety. The combination of these three factors allows a comprehensive evaluation of the different aspects that affect the geometric design consistency of a highway. The methodology was applied to some Spanish and Colombian roads located in different types of terrain.

Numerical simulation of tangling in jet engine turbines

The numerical analysis of certain safety related problems presents serious difficulties, since the large number of components present leads to huge finite elementmodels that can only be solved by using large and expensive computers or by making rough approaches to the problem. Tangling, or clashing, in the turbine of a jet engine airplane is an example of such problems. This is caused by the crash and friction between rotor and stator blades in the turbine after an eventual shaft failure. When facing the study of an event through numerical modelling, the accurate simulation of this problem would require the engineer to model all the rotor and stator blades existing in the turbine stage, using a small element size in all pieces. Given that the number of stator and rotor blades is usually around 200, such simulations would require millions of elements. This work presents a new numerical methodology, specifically developed for the accurate modelling of the tangling problem that, depending on the turbine configuration, is able to reduce the number of nodes up to an order of magnitude without losing accuracy. The methodology, which benefits from the cyclic configuration of turbines, is successfully applied to the numerical analysis of a hypothetical tangling event in a turbine, providing valuable data such as the rotating velocity decrease of the turbine, the braking torque and the damage suffered by the blades. The methodology is somewhat general and can be applied to any problem in which damage caused by the interaction between a rotating and static piece is to be analysed.

Simulation, Design and Analysis of Air-Breathing Combined-Cycle Engines for High Speed Propulsion

Desde la aparición del turborreactor, el motor aeróbico con turbomaquinaria ha demostrado unas prestaciones excepcionales en los regímenes subsónico y supersónico bajo. No obstante, la operación a velocidades superiores requiere sistemas más complejos y pesados, lo cual ha imposibilitado la ejecución de estos conceptos. Los recientes avances tecnológicos, especialmente en materiales ligeros, han restablecido el interés por los motores de ciclo combinado. La simulación numérica de estos nuevos conceptos es esencial para estimar las prestaciones de la planta propulsiva, así como para abordar las dificultades de integración entre célula y motor durante las primeras etapas de diseño. Al mismo tiempo, la evaluación de estos extraordinarios motores requiere una metodología de análisis distinta. La tesis doctoral versa sobre el diseño y el análisis de los mencionados conceptos propulsivos mediante el modelado numérico y la simulación dinámica con herramientas de vanguardia. Las distintas arquitecturas presentadas por los ciclos combinados basados en sendos turborreactor y motor cohete, así como los diversos sistemas comprendidos en cada uno de ellos, hacen necesario establecer una referencia común para su evaluación. Es más, la tendencia actual hacia aeronaves "más eléctricas" requiere una nueva métrica para juzgar la aptitud de un proceso de generación de empuje en el que coexisten diversas formas de energía. A este respecto, la combinación del Primer y Segundo Principios define, en un marco de referencia absoluto, la calidad de la trasferencia de energía entre los diferentes sistemas. Esta idea, que se ha estado empleando desde hace mucho tiempo en el análisis de plantas de potencia terrestres, ha sido extendida para relacionar la misión de la aeronave con la ineficiencia de cada proceso involucrado en la generación de empuje. La metodología se ilustra mediante el estudio del motor de ciclo combinado variable de una aeronave para el crucero a Mach 5. El diseño de un acelerador de ciclo combinado basado en el turborreactor sirve para subrayar la importancia de la integración del motor y la célula. El diseño está limitado por la trayectoria ascensional y el espacio disponible en la aeronave de crucero supersónico. Posteriormente se calculan las prestaciones instaladas de la planta propulsiva en función de la velocidad y la altitud de vuelo y los parámetros de control del motor: relación de compresión, relación aire/combustible y área de garganta. ABSTRACT Since the advent of the turbojet, the air-breathing engine with rotating machinery has demonstrated exceptional performance in the subsonic and low supersonic regimes. However, the operation at higher speeds requires further system complexity and weight, which so far has impeded the realization of these concepts. Recent technology developments, especially in lightweight materials, have restored the interest towards combined-cycle engines. The numerical simulation of these new concepts is essential at the early design stages to compute a first estimate of the engine performance in addition to addressing airframe-engine integration issues. In parallel, a different analysis methodology is required to evaluate these unconventional engines. The doctoral thesis concerns the design and analysis of the aforementioned engine concepts by means of numerical modeling and dynamic simulation with state-of-the-art tools. A common reference is needed to evaluate the different architectures of the turbine and the rocket-based combined-cycle engines as well as the various systems within each one of them. Furthermore, the actual trend towards more electric aircraft necessitates a common metric to judge the suitability of a thrust generation process where different forms of energy coexist. In line with this, the combination of the First and the Second Laws yields the quality of the energy being transferred between the systems on an absolute reference frame. This idea, which has been since long applied to the analysis of on-ground power plants, was extended here to relate the aircraft mission with the inefficiency of every process related to the thrust generation. The methodology is illustrated with the study of a variable- combined-cycle engine for a Mach 5 cruise aircraft. The design of a turbine-based combined-cycle booster serves to highlight the importance of the engine-airframe integration. The design is constrained by the ascent trajectory and the allocated space in the supersonic cruise aircraft. The installed performance of the propulsive plant is then computed as a function of the flight speed and altitude and the engine control parameters: pressure ratio, air-to-fuel ratio and throat area.

Estudio de la respuesta dinámica transversal de viaductos altos de líneas de ferrocarril de alta velocidad bajo la acción de cargas de uso

Es conocido que las dimensiones de los puentes de ferrocarril han ido cambiando debido a las estrictas condiciones de trazado impuestas en las líneas de alta velocidad. Además, la creciente preocupación de la sociedad por cuidar y proteger el medio ambiente, reflejado en la correspondiente normativa, ha generado nuevos condicionantes en el diseño de estas infraestructuras. En concreto, se ha limitado el movimiento de grandes volúmenes de terreno particularmente en los espacios protegidos. Por estas razones, hoy en día se proyectan y construyen puentes de ferrocarril más altos y más largos en todo el mundo. En España se han construido varios viaductos de pilas altas para líneas de alta velocidad. Ejemplos de estas infraestructuras son el Viaducto O’Eixo y el Viaducto de Barbantiño, situados en la línea de alta velocidad Madrid-Galicia, Estos viaductos altos se caracterizan por tener una mayor flexibilidad lateral y una frecuencia fundamental de oscilación baja, de hasta 0.2 Hz. La respuesta dinámica de este tipo de estructura puede aumentar como consecuencia de la aproximación entre la frecuencias propias de la misma y las de excitación debidas al paso del tren y a la acción del viento. Por lo tanto, estas estructuras pueden presentar problemas a la hora de cumplir con las limitaciones impuestas en las normas de diseño de puentes de ferrocarril, y otras, para garantizar la seguridad del tráfico y el confort de los viajeros. La respuesta dinámica lateral de viaductos de pilas altas no ha sido suficientemente estudiada en la literatura científica. Se pueden intuir varios de los motivos para explicar esta carencia. El primero es la relativamente reciente aparición de este tipo de viaductos asociados al desarrollo de la alta velocidad. Por otro lado, se hace necesario, para estudiar este tema, construir nuevos modelos numéricos adecuados para el estudio de la interacción dinámica lateral del puente y del tren. La interacción entre el puente y un tren viajando sobre él es un problema dinámico no lineal, dependiente del tiempo y de acoplamiento entre los dos subsistemas que intervienen (vehículo y puente). Los dos subsistemas, que pueden ser modelados como estructuras elásticas, interaccionan el uno con el otro a través de las fuerzas de contacto, que tiene una marcada naturaleza no lineal por el rozamiento entre rueda y carril, y por la geometría de los perfiles de estos dos elementos en contacto. En esta tesis, se desarrolla la formulación completa de un modelo no lineal de interacción tren-vía-puente-viento que reproduce adecuadamente las fuerzas laterales de contacto rueda-carril, fuerzas que van a tener una gran influencia en los índices de seguridad del tráfico. Este modelo se ha validado a partir de casos resueltos en la literatura científica, y de medidas experimentales tomadas en eventos dinámicos ocurridos en los viaductos de Arroyo de Valle y Arroyo de las Piedras. Puentes altos que han estado monitorizados en servicio durante dos años. En los estudios realizados en este trabajo, se cuantifican, empleando el modelo construido, los niveles de seguridad del tráfico y de confort de los pasajeros de trenes ligeros de alta velocidad, como el tren articulado AVE S-100, que viajan sobre viaductos altos sometidos, o no, a fuertes vientos laterales racheados. Finalmente, se ha obtenido el grado de mejora de la seguridad del tráfico y del confort de los viajeros, cuando se emplean pantallas anti-viento en el tablero y amortiguadores de masa sintonizados en la cabeza de las pilas de un viaducto alto. Resultando, el uso simultaneo de estos dos dispositivos (pantallas y amortiguadores de masa), en puentes altos de líneas de alta velocidad, una opción a considerar en la construcción de estas estructuras para elevar significativamente el nivel de servicio de las mismas. It is known that dimensions of railway bridges have been changing due to the strict high-speed lines layout parameters. Moreover, the growing concern of society to take care of and protect the environment, reflected in the corresponding regulations, has created new environment requirements for the design of these infrastructures. Particularly, the mentioned regulations do not allow designers to move far from terrain to build these railway lines. Due to all these reasons, longer and higher railway bridges are being designed and built around the world. In Spain, several high pier railway viaducts have been built for high speed lines. Barbantiño Viaduct and Eixo Viaduct, belonging to the Madrid-Galicia high speed line, are examples of this kind of structures. These high viaducts have great lateral flexibility and a low fundamental vibration frequency of down to 0.2 Hz. The dynamic response of high speed railway bridges may increase because of the approximation between the natural viaduct frequencies and the excitation ones due to the train travel and the wind action. Therefore, this bridge response could not satisfy the serviceability limits states, for traffic safety and for passenger comfort, considered by the design standards of high speed bridges. It is difficult to find papers in the scientific literature about the lateral response of high-speed trains travel over long viaducts with high piers. Several reasons could explain this issue. On one hand, the construction of this kind of viaduct is relatively recent and it is associated to the development of the high speed railway. On the other hand, in order to study the dynamic lateral interaction between the train and the high bridge, it is necessary to build new numerical and complex models. The interaction between the bridge-track subsystem and the vehicle subsystem travelling over the bridge is a coupling, nonlinear and time dependent problem. Both subsystems, train and bridge, which can be modelled as elastic structures, interact each other through the contact forces. These forces have a strong nonlinear nature due to the friction and the geometry of rail and wheel profiles. In this thesis, the full formulation of a train-track-bridge-wind nonlinear interaction model is developed. This model can reproduce properly the lateral contact wheel-rail forces, which have a great influence on traffic safety indices. The validation of the model built has been reached through interaction solved cases found in the scientific literature and experimental measures taken in dynamic events which happened at Arroyo de las Piedras and Arroyo del Valle Viaducts. These high bridges have been controlled during two years of service by means of structural health monitoring. In the studies carried out for this thesis, the levels of traffic safety and passenger comfort are quantified using the interaction model built, in the cases of high speed and light trains, as AVE S-100, travelling over high pier bridges and with or without lateral turbulent winds acting. Finally, the improvement rate of the traffic safety and passenger comfort has been obtained, when wind barriers are used at the bridge deck and tuned mass dampers are installed at the pier heads of a high viaduct. The installation of both devices, wind barriers and tuned mass damper, at the same time, turned out to be a good option to be considered in the design of high pier railway viaducts, to improve significantly the serviceability level of this kind of structures.

Optimización del consumo de combustible de un vehículo dependiendo de las condiciones de la carretera

El consumo de combustible en un automóvil es una característica que se intenta mejorar continuamente debido a los precios del carburante y a la creciente conciencia medioambiental. Esta tesis doctoral plantea un algoritmo de optimización del consumo que tiene en cuenta las especificaciones técnicas del vehículo, el perfil de orografía de la carretera y el tráfico presente en ella. El algoritmo de optimización calcula el perfil de velocidad óptima que debe seguir el vehículo para completar un recorrido empleando un tiempo de viaje especificado. El cálculo del perfil de velocidad óptima considera los valores de pendiente de la carretera así como también las condiciones de tráfico vehicular de la franja horaria en que se realiza el recorrido. El algoritmo de optimización reacciona ante condiciones de tráfico cambiantes y adapta continuamente el perfil óptimo de velocidad para que el vehículo llegue al destino cumpliendo el horario de llegada establecido. La optimización de consumo es aplicada en vehículos convencionales de motor de combustión interna y en vehículos híbridos tipo serie. Los datos de consumo utilizados por el algoritmo de optimización se obtienen mediante la simulación de modelos cuasi-estáticos de los vehículos. La técnica de minimización empleada por el algoritmo es la Programación Dinámica. El algoritmo divide la optimización del consumo en dos partes claramente diferenciadas y aplica la Programación Dinámica sobre cada una de ellas. La primera parte corresponde a la optimización del consumo del vehículo en función de las condiciones de tráfico. Esta optimización calcula un perfil de velocidad promedio que evita, cuando es posible, las retenciones de tráfico. El tiempo de viaje perdido durante una retención de tráfico debe recuperarse a través de un aumento posterior de la velocidad promedio que incrementaría el consumo del vehículo. La segunda parte de la optimización es la encargada del cálculo de la velocidad óptima en función de la orografía y del tiempo de viaje disponible. Dado que el consumo de combustible del vehículo se incrementa cuando disminuye el tiempo disponible para finalizar un recorrido, esta optimización utiliza factores de ponderación para modular la influencia que tiene cada una de estas dos variables en el proceso de minimización. Aunque los factores de ponderación y la orografía de la carretera condicionan el nivel de ahorro de la optimización, los perfiles de velocidad óptima calculados logran ahorros de consumo respecto de un perfil de velocidad constante que obtiene el mismo tiempo de recorrido. Las simulaciones indican que el ahorro de combustible del vehículo convencional puede lograr hasta un 8.9% mientras que el ahorro de energía eléctrica del vehículo híbrido serie un 2.8%. El algoritmo fusiona la optimización en función de las condiciones del tráfico y la optimización en función de la orografía durante el cálculo en tiempo real del perfil óptimo de velocidad. La optimización conjunta se logra cuando el perfil de velocidad promedio resultante de la optimización en función de las condiciones de tráfico define los valores de los factores de ponderación de la optimización en función de la orografía. Aunque el nivel de ahorro de la optimización conjunta depende de las condiciones de tráfico, de la orografía, del tiempo de recorrido y de las características propias del vehículo, las simulaciones indican ahorros de consumo superiores al 6% en ambas clases de vehículo respecto a optimizaciones que no logran evitar retenciones de tráfico en la carretera. ABSTRACT Fuel consumption of cars is a feature that is continuously being improved due to the fuel price and an increasing environmental awareness. This doctoral dissertation describes an optimization algorithm to decrease the fuel consumption taking into account the technical specifications of the vehicle, the terrain profile of the road and the traffic conditions of the trip. The algorithm calculates the optimal speed profile that completes a trip having a specified travel time. This calculation considers the road slope and the expected traffic conditions during the trip. The optimization algorithm is also able to react to changing traffic conditions and tunes the optimal speed profile to reach the destination within the specified arrival time. The optimization is applied on a conventional vehicle and also on a Series Hybrid Electric vehicle (SHEV). The fuel consumption optimization algorithm uses data obtained from quasi-static simulations. The algorithm is based on Dynamic Programming and divides the fuel consumption optimization problem into two parts. The first part of the optimization process reduces the fuel consumption according to foreseeable traffic conditions. It calculates an average speed profile that tries to avoid, if possible, the traffic jams on the road. Traffic jams that delay drivers result in higher vehicle speed to make up for lost time. A higher speed of the vehicle within an already defined time scheme increases fuel consumption. The second part of the optimization process is in charge of calculating the optimal speed profile according to the road slope and the remaining travel time. The optimization tunes the fuel consumption and travel time relevancies by using two penalty factors. Although the optimization results depend on the road slope and the travel time, the optimal speed profile produces improvements of 8.9% on the fuel consumption of the conventional car and of 2.8% on the spent energy of the hybrid vehicle when compared with a constant speed profile. The two parts of the optimization process are combined during the Real-Time execution of the algorithm. The average speed profile calculated by the optimization according to the traffic conditions provides values for the two penalty factors utilized by the second part of the optimization process. Although the savings depend on the road slope, traffic conditions, vehicle features, and the remaining travel time, simulations show that this joint optimization process can improve the energy consumption of the two vehicles types by more than 6%.