Optimal design of a beam subjected to compression forces in the framework of different structural models

The optimal design of a vertical cantilever beam is presented in this paper. The beam is assumed immersed in an elastic Winkler soil and subjected to several loads: a point force at the tip section, its self weight and a uniform distributed load along its length. lbe optimal design problem is to find the beam of a given length and minimum volume, such that the resultant compressive stresses are admisible. This prohlem is analyzed according to linear elasticity theory and within different alternative structural models: column, Navier-Bernoulli beam-column, Timoshenko beamcolumn (i.e. with shear strain) under conservative loads, typically, constant direction loads. Results obtained in each case are compared, in order to evaluate the sensitivity of model on the numerical results. The beam optimal design is described by the section distribution layout (area, second moment, shear area etc.) along the beam span and the corresponding beam total volume. Other situations, some of them very interesting from a theoretical point of view, with follower loads (Beck and Leipholz problems) are also discussed, leaving for future work numerical details and results.

Vulnerability analysis of RC buildings with wide beams located in moderate seismicity regions

A significant number of short-to-mid height RC buildings with wide beams have been constructed in areas of moderate seismicity of Spain, mainly for housing and administrative use. The buildings have a framed structure with one-way slabs; the wide beams constitute the distinctive characteristic, their depth being equal to that of the rest of the slab, thus providing a flat lower surface, convenient for construction and the layout of facilities. Seismic behavior in the direction of the wide beams appears to be deficient because of: (i) low lateral strength, mainly because of the small effective depth of the beams, (ii) inherent low ductility of the wide beams, generated by high amount of reinforcement, (iii) the big strut compressive forces developed inside the column-beam connections due to the low height of the beams, and (iv) the fact that the wide beams are wider than the columns, meaning that the contribution of the outer zones to the resistance of the beam-column joints is unreliable because there is no torsion reinforcement. In the orthogonal direction, the behavior is worse since the only members of the slabs that contribute to the lateral resistance are the joists and the façade beams. Moreover, these buildings were designed with codes that did not include ductility requirements and required only a low lateral resistance; indeed, in many cases, seismic action was not considered at all. Consequently, the seismic capacity of these structures is not reliable. The objective of this research is to assess numerically this capability, whereas further research will aim to propose retrofit strategies. The research approach consists of: (i) selecting a number of 3-story and 6-story buildings that represent the vast majority of the existing ones and (ii) evaluating their vulnerability through three types of analyses, namely: code-type, push-over and nonlinear dynamic analysis. Given the low lateral resistance of the main frames, the cooperation of the masonry infill walls is accounted for; for each representative building, three wall densities are considered. The results of the analyses show that the buildings in question exhibit inadequate seismic behavior in most of the examined situations. In general, the relative performance is less deficient for Target Drift CP (Collapse Prevention) than for IO (Immediate Occupancy). Since these buildings are selected to be representative of the vast majority of buildings with wide beams that were constructed in Spain without accounting for any seismic consideration, our conclusions can be extrapolated to a broader scenario.

Inestabilidad de pórticos planos metálicos de edificación con inclusión de la flexibilidad de las uniones y elementos no prismáticos : un enfoque para la optimización

En esta tesis se aborda el problema de la modelización, análisis y optimización de pórticos metálicos planos de edificación frente a los estados límites último y de servicio. El objetivo general es presentar una técnica secuencial ordenada de optimización discreta para obtener el coste mínimo de pórticos metálicos planos de edificación, teniendo en cuenta las especificaciones del EC-3, incorporando las uniones semirrígidas y elementos no prismáticos en el proceso de diseño. Asimismo se persigue valorar su grado de influencia sobre el diseño final. El horizonte es extraer conclusiones prácticas que puedan ser de utilidad y aplicación simple para el proyecto de estructuras metálicas. La cantidad de publicaciones técnicas y científicas sobre la respuesta estructural de entramados metálicos es inmensa; por ello se ha hecho un esfuerzo intenso en recopilar el estado actual del conocimiento, sobre las líneas y necesidades actuales de investigación. Se ha recabado información sobre los métodos modernos de cálculo y diseño, sobre los factores que influyen sobre la respuesta estructural, sobre técnicas de modelización y de optimización, al amparo de las indicaciones que algunas normativas actuales ofrecen sobre el tema. En esta tesis se ha desarrollado un procedimiento de modelización apoyado en el método de los elementos finitos implementado en el entorno MatLab; se han incluido aspectos claves tales como el comportamiento de segundo orden, la comprobación ante inestabilidad y la búsqueda del óptimo del coste de la estructura frente a estados límites, teniendo en cuenta las especificaciones del EC-3. También se ha modelizado la flexibilidad de las uniones y se ha analizado su influencia en la respuesta de la estructura y en el peso y coste final de la misma. Se han ejecutado algunos ejemplos de aplicación y se ha contrastado la validez del modelo con resultados de algunas estructuras ya analizadas en referencias técnicas conocidas. Se han extraído conclusiones sobre el proceso de modelización y de análisis, sobre la repercusión de la flexibilidad de las uniones en la respuesta de la estructura. El propósito es extraer conclusiones útiles para la etapa de proyecto. Una de las principales aportaciones del trabajo en su enfoque de optimización es la incorporación de una formulación de elementos no prismáticos con uniones semirrígidas en sus extremos. Se ha deducido una matriz de rigidez elástica para dichos elementos. Se ha comprobado su validez para abordar el análisis no lineal; para ello se han comparado los resultados con otros obtenidos tras aplicar otra matriz deducida analíticamente existente en la literatura y también mediante el software comercial SAP2000. Otra de las aportaciones de esta tesis es el desarrollo de un método de optimización del coste de pórticos metálicos planos de edificación en el que se tienen en cuenta aspectos tales como las imperfecciones, la posibilidad de incorporar elementos no prismáticos y la caracterización de las uniones semirrígidas, valorando la influencia de su flexibilidad sobre la respuesta de la estructura. Así, se han realizado estudios paramétricos para valorar la sensibilidad y estabilidad de las soluciones obtenidas, así como rangos de validez de las conclusiones obtenidas. This thesis deals with the problems of modelling, analysis and optimization of plane steel frames with regard to ultimate and serviceability limit states. The objective of this work is to present an organized sequential technique of discrete optimization for achieving the minimum cost of plane steel frames, taking into consideration the EC-3 specifications as well as including effects of the semi-rigid joints and non-prismatic elements in the design process. Likewise, an estimate of their influence on the final design is an aim of this work. The final objective is to draw practical conclusions which can be handful and easily applicable for a steel-structure project. An enormous amount of technical and scientific publications regarding steel frames is currently available, thus making the achievement of a comprehensive and updated knowledge a considerably hard task. In this work, a large variety of information has been gathered and classified, especially that related to current research lines and needs. Thus, the literature collected encompasses references related to state-of-the-art design methods, factors influencing the structural response, modelling and optimization techniques, as well as calculation and updated guidelines of some steel Design Codes about the subject. In this work a modelling procedure based on the finite element implemented within the MatLab programming environment has been performed. Several keys aspects have been included, such as second order behaviour, the safety assessment against structural instability and the search for an optimal cost considering the limit states according to EC-3 specifications. The flexibility of joints has been taken into account in the procedure hereby presented; its effects on the structural response, on the optimum weight and on the final cost have also been analysed. In order to confirm the validity and adequacy of this procedure, some application examples have been carried out. The results obtained were compared with those available from other authors. Several conclusions about the procedure that comprises modelling, analysis and design stages, as well as the effect of the flexibility of connections on the structural response have been drawn. The purpose is to point out some guidelines for the early stages of a project. One of the contributions of this thesis is an attempt for optimizing plane steel frames in which both non-prismatic beam-column-type elements and semi-rigid connections have been considered. Thus, an elastic stiffness matrix has been derived. Its validity has been tested through comparing its accuracy with other analytically-obtained matrices available in the literature, and with results obtained by the commercial software SAP2000. Another achievement of this work is the development of a method for cost optimization of plane steel building frames in which some relevant aspects have been taken in consideration. These encompass geometric imperfections, non-prismatic beam elements and the numerical characterization of semi-rigid connections, evaluating the effect of its flexibility on the structural response. Hence, some parametric analyses have been performed in order to assess the sensitivity, the stability of the outcomes and their range of applicability as well.

Análisis de elementos viga-columna en régimen no lineal con deformación por cortante

El hormigón estructural sigue siendo sin duda uno de los materiales más utilizados en construcción debido a su resistencia, rigidez y flexibilidad para diseñar estructuras. El cálculo de estructuras de hormigón, utilizando vigas y vigas-columna, es complejo debido a los fenómenos de acoplamiento entre esfuerzos y al comportamiento no lineal del material. Los modelos más empleados para su análisis son el de Bernoulli-Euler y el de Timoshenko, indicándose en la literatura la conveniencia de usar el segundo cuando la relación canto/luz no es pequeña o los elementos están fuertemente armados. El objetivo fundamental de esta tesis es el análisis de elementos viga y viga-columna en régimen no lineal con deformación por cortante, aplicando el concepto de Pieza Lineal Equivalente (PLE). Concepto éste que consiste básicamente en resolver el problema de una pieza en régimen no lineal, transformándolo en uno lineal equivalente, de modo que ambas piezas tengan la misma deformada y los mismos esfuerzos. Para ello, se hizo en primer lugar un estudio comparado de: las distintas propuestas que aplican la deformación por cortante, de los distintos modelos constitutivos y seccionales del hormigón estructural y de los métodos de cálculo no lineal aplicando el método de elementos finitos (MEF). Teniendo en cuenta que la resolución del problema no lineal se basa en la resolución de sucesivos problemas lineales empleando un proceso de homotopía, los problemas lineales de la viga y viga-columna de Timoshenko, se resuelven mediante MEF, utilizando soluciones nodalmente exactas (SNE) y acción repartida equivalente de cualquier orden. Se obtiene así, con muy pocos elementos finitos, una excelente aproximación de la solución, no sólo en los nodos sino en el interior de los elementos. Se introduce el concepto PLE para el análisis de una barra, de material no lineal, sometida a acciones axiales, y se extiende el mismo para el análisis no lineal de vigas y vigas-columna con deformación por cortante. Cabe señalar que para estos últimos, la solución de una pieza en régimen no lineal es igual a la de una en régimen lineal, cuyas rigideces son constantes a trozos, y donde además hay que añadir momentos y cargas puntuales ficticias en los nodos, así como, un momento distribuido ficticio en toda la pieza. Se han desarrollado dos métodos para el análisis: uno para problemas isostáticos y otro general, aplicable tanto a problemas isostáticos como hiperestáticos. El primero determina de entrada la PLE, realizándose a continuación el cálculo por MEF-SNE de dicha pieza, que ahora está en régimen lineal. El general utiliza una homotopía que transforma de manera iterativa, unas leyes constitutivas lineales en las leyes no lineales del material. Cuando se combina con el MEF, la pieza lineal equivalente y la solución del problema original quedan determinadas al final de todo el proceso. Si bien el método general es un procedimiento próximo al de Newton- Raphson, presenta sobre éste la ventaja de permitir visualizar las deformaciones de la pieza en régimen no lineal, de manera tanto cualitativa como cuantitativa, ya que es posible observar en cada paso del proceso la modificación de rigideces (a flexión y cortante) y asimismo la evolución de las acciones ficticias. Por otra parte, los resultados obtenidos comparados con los publicados en la literatura, indican que el concepto PLE ofrece una forma directa y eficiente para analizar con muy buena precisión los problemas asociados a vigas y vigas-columna en las que por su tipología los efectos del cortante no pueden ser despreciados. ABSTRACT The structural concrete clearly remains the most used material in construction due to its strength, rigidity and structural design flexibility. The calculation of concrete structures using beams and beam-column is complex as consequence of the coupling phenomena between stresses and of its nonlinear behaviour. The models most commonly used for analysis are the Bernoulli-Euler and Timoshenko. The second model is strongly recommended when the relationship thickness/span is not small or in case the elements are heavily reinforced. The main objective of this thesis is to analyse the beam and beam-column elements with shear deformation in nonlinear regime, applying the concept of Equivalent Linear Structural Element (ELSE). This concept is basically to solve the problem of a structural element in nonlinear regime, transforming it into an equivalent linear structural element, so that both elements have the same deformations and the same stresses. Firstly, a comparative study of the various proposals of applying shear deformation, of various constitutive and sectional models of structural concrete, and of the nonlinear calculation methods (using finite element methods) was carried out. Considering that the resolution of nonlinear problem is based on solving the successive linear problem, using homotopy process, the linear problem of Timoshenko beam and beam-columns is resolved by FEM, using the exact nodal solutions (ENS) and equivalent distributed load of any order. Thus, the accurate solution approximation can be obtained with very few finite elements for not only nodes, but also for inside of elements. The concept ELSE is introduced to analyse a bar of nonlinear material, subjected to axial forces. The same bar is then used for other nonlinear beam and beam-column analysis with shear deformation. It is noted that, for the last analyses, the solution of a structural element in nonlinear regime is equal to that of linear regime, in which the piecewise-stiffness is constant, the moments and fictitious point loads need to be added at nodes of each element, as well as the fictitious distributed moment on element. Two methods have been developed for analysis: one for isostatic problem and other more general, applicable for both isostatic and hiperstatic problem. The first method determines the ELSE, and then the calculation of this piece is performed by FEM-ENS that now is in linear regime. The general method uses the homotopy that transforms iteratively linear constitutive laws into nonlinear laws of material. When combined with FEM, the ELSE and the solution of the original problem are determined at the end of the whole process. The general method is well known as a procedure closed to Newton-Raphson procedure but presents an advantage that allows displaying deformations of the piece in nonlinear regime, in both qualitative and quantitative way. Since it is possible to observe the modification of stiffness (flexural and shear) in each step of process and also the evolution of the fictitious actions. Moreover, the results compared with those published in the literature indicate that the ELSE concept offers a direct and efficient way to analyze with very good accuracy the problems associated with beams and beams columns in which, by typology, the effects of shear cannot be neglected.

Seismic vulnerability analysis of wide-beam buildings in Spain

A number of short-to-mid height RC buildings with wide beams have been constructed in moderate-seismicity areas of Spain. The seismic behavior in the direction of the wide beams appears to be deficient because of low lateral strength, low ductility of the wide beams, big strut compressive forces inside the column-beam connections, and unreliable contribution of the spandrel zones of the wide beams. In the orthogonal direction, the behavior is worse since only the joists and the façade beams contribute to the lateral resistance. The objective is to assess the seismic capability of these structures; further research will involve proposing retrofit strategies. The research approach consists of selecting a number of representative buildings and evaluating their vulnerability by code-type, push-over and dynamic analyses. The cooperation of the masonry infill walls is accounted for. The main conclusion is that the seismic behavior of these buildings is inadequate in most of the situations.

Moment transfer and influence of transverse beams in interior waffle flat plate-column connections under lateral loading

This paper addresses two aspects of the behavior of interior reinforced concrete waffle flat plate?column connections under lateral loads: the share of the unbalanced moment between flexure and excentric shear, and the effect of the transverse beams. A non-linear finite element model (benchmark model) was developed and calibrated with the results of quasi-static cyclic tests conducted on a 3/5 scale specimen. First, from this numerical model, the portion cv of the unbalanced moment transferred by the excentricity of shear about the centroid of the critical sections defined by Eurocode 2 (EC-2) and by ACI 318-11 was calculated and compared with the share-out prescribed by these codes. It is found that while the critical section of EC-2 is consistent with the cv provided by this code, in the case of ACI 318-11, the value assigned to cv is far below (about 50% smaller) the actual one obtained with the numerical simulations. Second, from the benchmark model, seven additional models were developed by varying the depth D of the transverse beam over the thickness h of the plate. It was found that the ductility of the connection and the effective width of the plate can respectively be increased up to 50% and 10% by raising D/h to 2 and 1.5.