Hidrogeología e hidrodinámica del acuífero de los manantiales de Gormaz y su importancia en el caudal base del río Duero, España = Hydrogeology and hydrodynamic of the Gormaz Springs Aquifer and its importance to the base flow of the Duero River, Spain

Se cuantifican las descargas subterráneas de un acuífero a un río que lo atraviesa utilizando correlaciones estadísticas. El río Duero, España, incrementa su caudal base en varios m3/s, al atravesar unos afloramientos carbonatados mesozoicos en un pequeño tramo de su cabecera; esto es de especial importancia en época de estiaje, cuando la mayor parte del caudal base del río procede de manantiales que allí se sitúan. Dichos afloramientos corresponden a uno de los dos acuíferos calcáreos confinados, que se desarrollan en paralelo y están hidráulicamente desconectados por una capa impermeable, que forman el sistema acuífero de los manantiales de Gormaz. Este sistema se encuentra en estado de régimen natural y está apenas explotado. Se define el modelo conceptual de funcionamiento hidrogeológico, considerando el papel hidrogeológico de la falla de Gormaz, situada en la zona de descarga del sistema. Analizando información geológica antecedente y la geofísica exploratoria realizada, se obtuvo un mejor conocimiento de la geometría y los límites de los acuíferos, definiéndose un sistema acuífero con una zona de recarga en el sur, correspondiente a los afloramientos calcáreos, los cuales se confinan hacia el norte bajo el Terciario, hasta intersecar con la falla normal de Gormaz. El salto de falla genera una barrera para las formaciones permeables situadas al extremo norte (margen derecha del río Duero); a su vez, el plano de falla facilita el ascenso del agua subterránea del sistema acuífero en estudio y pone en conexión hidráulica los dos acuíferos. Se estimaron, además, los parámetros hidráulicos de los acuíferos en los alrededores de la falla. La buena correlación entre los niveles piezométricos y las descargas subterráneas al río Duero han permitido la reconstrucción del hidrograma de los manantiales de Gormaz en el periodo 1992-2006. Se calcula así que la contribución subterránea al río Duero es de 135.9 hm3/año, que supone el 18.9% de la aportación total del río. In a short stretch of its headwaters, the base flow of the River Duero increases by several m3/s as it traverses some Mesozoic carbonate outcrops. This is of special importance during the dry season, when the majority of the base flow of the river proceeds from springs in this reach. The outcrops correspond to one of two confined calcareous aquifers that developed in parallel but which are not hydraulically connected because of an impermeable layer. Together, they constitute the aquifer system of the Gormaz Springs. The system is still in its natural regime and is hardly exploited. This study defines the conceptual model of hydrogeological functioning, taking into consideration the role of the Gormaz Fault, which is situated in the discharge zone of the system. Analysis of both antecedent geological information and geophysical explorations has led to a better understanding of the geometry and boundaries of the aquifers, defining an aquifer system with a recharge zone in the south corresponding to in the calcareous outcrops. These calcareous outcrops are confined to the north below Tertiary formations, as far as their intersection with the normal fault of Gormaz. The throw of the fault forms the barrier of the permeable formations situated in the extreme north (right bank of the River Duero). In turn, the fault plane facilitates the upflow of groundwater from the aquifer system and creates hydraulic connection between the two aquifers. In addition, the study estimated the hydraulic parameters of the aquifer around the fault. The close correlation between piezometric levels and the groundwater discharges to the River Duero has enabled the reconstruction of the hydrogram of Gormaz springs over the period 1992-2006. By this means, it is calculated that the groundwater contribution to the River Duero is 135.9 hm3/year, or 18.9% of the total river inflow.

Efficient numerical methods for global linear instability. Analysis and modeling of non-orthogonal swept attachment-line boundary layer flow

The aim of this thesis is to study the mechanisms of instability that occur in swept wings when the angle of attack increases. For this, a simplified model for the a simplified model for the non-orthogonal swept leading edge boundary layer has been used as well as different numerical techniques in order to solve the linear stability problem that describes the behavior of perturbations superposed upon this base flow. Two different approaches, matrix-free and matrix forming methods, have been validated using direct numerical simulations with spectral resolution. In this way, flow instability in the non-orthogonal swept attachment-line boundary layer is addressed in a linear analysis framework via the solution of the pertinent global (Bi-Global) PDE-based eigenvalue problem. Subsequently, a simple extension of the extended G¨ortler-H¨ammerlin ODEbased polynomial model proposed by Theofilis, Fedorov, Obrist & Dallmann (2003) for orthogonal flow, which includes previous models as particular cases and recovers global instability analysis results, is presented for non-orthogonal flow. Direct numerical simulations have been used to verify the stability results and unravel the limits of validity of the basic flow model analyzed. The effect of the angle of attack, AoA, on the critical conditions of the non-orthogonal problem has been documented; an increase of the angle of attack, from AoA = 0 (orthogonal flow) up to values close to _/2 which make the assumptions under which the basic flow is derived questionable, is found to systematically destabilize the flow. The critical conditions of non-orthogonal flows at 0 _ AoA _ _/2 are shown to be recoverable from those of orthogonal flow, via a simple analytical transformation involving AoA. These results can help to understand the mechanisms of destabilization that occurs in the attachment line of wings at finite angles of attack. Studies taking into account variations of the pressure field in the basic flow or the extension to compressible flows are issues that remain open. El objetivo de esta tesis es estudiar los mecanismos de la inestabilidad que se producen en ciertos dispositivos aerodinámicos cuando se aumenta el ángulo de ataque. Para ello se ha utilizado un modelo simplificado del flujo de base, así como diferentes técnicas numéricas, con el fin de resolver el problema de estabilidad lineal asociado que describe el comportamiento de las perturbaciones. Estos métodos; sin y con formación de matriz, se han validado utilizando simulaciones numéricas directas con resolución espectral. De esta manera, la inestabilidad del flujo de capa límite laminar oblicuo entorno a la línea de estancamiento se aborda en un marco de análisis lineal por medio del método Bi-Global de resolución del problema de valores propios en derivadas parciales. Posteriormente se propone una extensión simple para el flujo no-ortogonal del modelo polinomial de ecuaciones diferenciales ordinarias, G¨ortler-H¨ammerlin extendido, propuesto por Theofilis et al. (2003) para el flujo ortogonal, que incluye los modelos previos como casos particulares y recupera los resultados del analisis global de estabilidad lineal. Se han realizado simulaciones directas con el fin de verificar los resultados del análisis de estabilidad así como para investigar los límites de validez del modelo de flujo base utilizado. En este trabajo se ha documentado el efecto del ángulo de ataque AoA en las condiciones críticas del problema no ortogonal obteniendo que el incremento del ángulo de ataque, de AoA = 0 (flujo ortogonal) hasta valores próximos a _/2, en el cual las hipótesis sobre las que se basa el flujo base dejan de ser válidas, tiende sistemáticamente a desestabilizar el flujo. Las condiciones críticas del caso no ortogonal 0 _ AoA _ _/2 pueden recuperarse a partir del caso ortogonal mediante el uso de una transformación analítica simple que implica el ángulo de ataque AoA. Estos resultados pueden ayudar a comprender los mecanismos de desestabilización que se producen en el borde de ataque de las alas de los aviones a ángulos de ataque finitos. Como tareas pendientes quedaría realizar estudios que tengan en cuenta variaciones del campo de presión en el flujo base así como la extensión de éste al caso de flujos compresibles.

Accurate Parabolic Navier-Stokes solutions of the supersonic flow around and elliptic cone

Flows of relevance to new generation aerospace vehicles exist, which are weakly dependent on the streamwise direction and strongly dependent on the other two spatial directions, such as the flow around the (flattened) nose of the vehicle and the associated elliptic cone model. Exploiting these characteristics, a parabolic integration of the Navier-Stokes equations is more appropriate than solution of the full equations, resulting in the so-called Parabolic Navier-Stokes (PNS). This approach not only is the best candidate, in terms of computational efficiency and accuracy, for the computation of steady base flows with the appointed properties, but also permits performing instability analysis and laminar-turbulent transition studies a-posteriori to the base flow computation. This is to be contrasted with the alternative approach of using order-of-magnitude more expensive spatial Direct Numerical Simulations (DNS) for the description of the transition process. The PNS equations used here have been formulated for an arbitrary coordinate transformation and the spatial discretization is performed using a novel stable high-order finite-difference-based numerical scheme, ensuring the recovery of highly accurate solutions using modest computing resources. For verification purposes, the boundary layer solution around a circular cone at zero angle of attack is compared in the incompressible limit with theoretical profiles. Also, the recovered shock wave angle at supersonic conditions is compared with theoretical predictions in the same circular-base cone geometry. Finally, the entire flow field, including shock position and compressible boundary layer around a 2:1 elliptic cone is recovered at Mach numbers 3 and 4

Global Stability Analysis of a Compressible Turbulent Flow around a High-Lift Configuration

The purpose of this work is to analyze a complex high lift configuration for which significant regions of separated flow are present. Current state of the art methods have some diffculty to predict the origin and the progression of this separated flow when increasing the angle of attack. The mechanisms responsible for the maximum lift limit on multi-element wing con?gurations are not clear; this stability analysis could help to understand the physics behind the phenomenon and to find a relation between the flow separation and the instability onset. The methodology presented herein consists in the computation of a steady base flow solution based on a finite volume discretization and a proposal of the solution for a generalized eigenvalue problem corresponding to the perturbed and linearized problem. The eigenvalue problem has been solved with the Arnoldi iterative method, one of the Krylov subspace projection methods. The described methodology was applied to the NACA0012 test case in subsonic and in transonic conditions and, finally, for the first time to the authors knowledge, on an industrial multi-component geometry, such as the A310 airfoil, in order to identify low frequency instabilities related to the separation. One important conclusion is that for all the analyzed geometries, one unstable mode related to flow separation appears for an angle of attack greater than the one correspondent to the maximum lift coe?cient condition. Finally, an adjoint study was carried out in order to evaluate the receptivity and the structural sensitivity of the geometries, giving an indication of the domain region that could be modified resulting in the biggest change of the flowfield.

Global instability analysis and control of three-dimensional long open cavity flow

The three-dimensional wall-bounded open cavity may be considered as a simplified geometry found in industrial applications such as leading gear or slotted flats on the airplane. Understanding the three-dimensional complex flow structure that surrounds this particular geometry is therefore of major industrial interest. At the light of the remarkable former investigations in this kind of flows, enough evidences suggest that the lateral walls have a great influence on the flow features and hence on their instability modes. Nevertheless, even though there is a large body of literature on cavity flows, most of them are based on the assumption that the flow is two-dimensional and spanwise-periodic. The flow over realistic open cavity should be considered. This thesis presents an investigation of three-dimensional wall-bounded open cavity with geometric ratio 6:2:1. To this aim, three-dimensional Direct Numerical Simulation (DNS) and global linear instability have been performed. Linear instability analysis reveals that the onset of the first instability in this open cavity is around Recr 1080. The three-dimensional shear layer mode with a complex structure is shown to be the most unstable mode. I t is noteworthy that the flow pattern of this high-frequency shear layer mode is similar to the observed unstable oscillations in supercritical unstable case. DNS of the cavity flow carried out at different Reynolds number from steady state until a nonlinear saturated state is obtained. The comparison of time histories of kinetic energy presents a clearly dominant energetic mode which shifts between low-frequency and highfrequency oscillation. A complete flow patterns from subcritical cases to supercritical case has been put in evidence. The flow structure at the supercritical case Re=1100 resembles typical wake-shedding instability oscillations with a lateral motion existed in the subcritical cases. Also, This flow pattern is similar to the observations in experiments. In order to validate the linear instability analysis results, the topology of the composite flow fields reconstructed by linear superposition of a three-dimensional base flow and its leading three-dimensional global eigenmodes has been studied. The instantaneous wall streamlines of those composited flows display distinguish influence region of each eigenmode. Attention has been focused on the leading high-frequency shear layer mode; the composite flow fields have been fully recognized with respect to the downstream wave shedding. The three-dimensional shear layer mode is shown to give rise to a typical wake-shedding instability with a lateral motions occurring downstream which is in good agreement with the experiment results. Moreover, the spanwise-periodic, open cavity with the same length to depth ratio has been also studied. The most unstable linear mode is different from the real three-dimensional cavity flow, because of the existence of the side walls. Structure sensitivity of the unstable global mode is analyzed in the flow control context. The adjoint-based sensitivity analysis has been employed to localized the receptivity region, where the flow is more sensible to momentum forcing and mass injection. Because of the non-normality of the linearized Navier-Stokes equations, the direct and adjoint field has a large spatial separation. The strongest sensitivity region is locate in the upstream lip of the three-dimensional cavity. This numerical finding is in agreement with experimental observations. Finally, a prototype of passive flow control strategy is applied.

Low cost 3D global instability analysis and flow sensitivity based on dynamic mode decomposition and high-order numerical tools

We explore the recently developed snapshot-based dynamic mode decomposition (DMD) technique, a matrix-free Arnoldi type method, to predict 3D linear global flow instabilities. We apply the DMD technique to flows confined in an L-shaped cavity and compare the resulting modes to their counterparts issued from classic, matrix forming, linear instability analysis (i.e. BiGlobal approach) and direct numerical simulations. Results show that the DMD technique, which uses snapshots generated by a 3D non-linear incompressible discontinuous Galerkin Navier?Stokes solver, provides very similar results to classical linear instability analysis techniques. In addition, we compare DMD results issued from non-linear and linearised Navier?Stokes solvers, showing that linearisation is not necessary (i.e. base flow not required) to obtain linear modes, as long as the analysis is restricted to the exponential growth regime, that is, flow regime governed by the linearised Navier?Stokes equations, and showing the potential of this type of analysis based on snapshots to general purpose CFD codes, without need of modifications. Finally, this work shows that the DMD technique can provide three-dimensional direct and adjoint modes through snapshots provided by the linearised and adjoint linearised Navier?Stokes equations advanced in time. Subsequently, these modes are used to provide structural sensitivity maps and sensitivity to base flow modification information for 3D flows and complex geometries, at an affordable computational cost. The information provided by the sensitivity study is used to modify the L-shaped geometry and control the most unstable 3D mode.

Flow around a hemisphere-cylinder at high angle of attack and low Reynolds number. Part I: Experimental and numerical investigation

Three-dimensional Direct Numerical Simulations combined with Particle Image Velocimetry experiments have been performed on a hemisphere-cylinder at Reynolds number 1000 and angle of attack 20◦. At these flow conditions, a pair of vortices, so-called “horn” vortices, are found to be associated with flow separation. In order to understand the highly complex phenomena associated with this fully threedimensional massively separated flow, different structural analysis techniques have been employed: Proper Orthogonal and Dynamic Mode Decompositions, POD and DMD, respectively, as well as criticalpoint theory. A single dominant frequency associated with the von Karman vortex shedding has been identified in both the experimental and the numerical results. POD and DMD modes associated with this frequency were recovered in the analysis. Flow separation was also found to be intrinsically linked to the observed modes. On the other hand, critical-point theory has been applied in order to highlight possible links of the topology patterns over the surface of the body with the computed modes. Critical points and separation lines on the body surface show in detail the presence of different flow patterns in the base flow: a three-dimensional separation bubble and two pairs of unsteady vortices systems, the horn vortices, mentioned before, and the so-called “leeward” vortices. The horn vortices emerge perpendicularly from the body surface at the separation region. On the other hand, the leeward vortices are originated downstream of the separation bubble, as a result of the boundary layer separation. The frequencies associated with these vortical structures have been quantified.

The scenario of two-dimensional instabilities of the cylinder wake under EHD forcing: A linear stability analysis

We propose to study the stability properties of an air flow wake forced by a dielectric barrier discharge (DBD) actuator, which is a type of electrohydrodynamic (EHD) actuator. These actuators add momentum to the flow around a cylinder in regions close to the wall and, in our case, are symmetrically disposed near the boundary layer separation point. Since the forcing frequencies, typical of DBD, are much higher than the natural shedding frequency of the flow, we will be considering the forcing actuation as stationary. In the first part, the flow around a circular cylinder modified by EHD actuators will be experimentally studied by means of particle image velocimetry (PIV). In the second part, the EHD actuators have been numerically implemented as a boundary condition on the cylinder surface. Using this boundary condition, the computationally obtained base flow is then compared with the experimental one in order to relate the control parameters from both methodologies. After validating the obtained agreement, we study the Hopf bifurcation that appears once the flow starts the vortex shedding through experimental and computational approaches. For the base flow derived from experimentally obtained snapshots, we monitor the evolution of the velocity amplitude oscillations. As to the computationally obtained base flow, its stability is analyzed by solving a global eigenvalue problem obtained from the linearized Navier–Stokes equations. Finally, the critical parameters obtained from both approaches are compared.

A method to assess annual average renewable groundwater reserves for large regions in Spain

This paper proposes a method for assessing the groundwater renewable reserves of large regions for an average year, based on the integration of the recession curves for their basins springs or the natural base flow of their rivers. In this method, the hydrodynamic volume (or renewable reserves), were estimated from the baseflow equation. It was assumed that the flow was the same as the natural recharge, and that the recession coefficients were derived by the hydrogeological parameters and geometrical characteristics of aquifers, and adjusted to fit the recession curves at gauging stations. The method was applied to all the aquifers of Spain, which have a total groundwater renewable reserve of 86,895 hm3 four times the mean annual recharge. However, the distribution of these reserves is very variable; 18.6% of the country aquifers contain 94.7% of the entire reserve.

Comportamiento hidrológico de cuencas de media montaña españolas: efectos de los procesos de acumulación / fusión de nieve en terrenos permeables sobre la infiltración y régimen de caudales Alto Tajo

La infiltración de agua en el suelo y la recarga profunda del agua subterránea contenida en los acuíferos es un proceso lento en relación con otros fenómenos hidrológicos. La redacción de esta tesis ha pretendido contribuir al estudio de la influencia que el almacenamiento de la precipitación sólida en forma de manto de nieve y su eventual fusión puedan tener sobre dicho proceso en áreas de media montaña (1.000 – 2.000 m.) en las que con gran frecuencia se sitúan las cabeceras de los ríos peninsulares. Para ello se ha partido del análisis de las diferentes variables intervinientes durante un determinado periodo temporal y sobre un espacio geográfico concreto, por lo que su metodología es de naturaleza empírica. La extensión del periodo (2002/03 a 2010/11) ha venido condicionada por la disponibilidad de los valores de algunas de sus principales variables, como han sido el equivalente en agua de la nieve acumulada y los caudales procedentes de su fusión. Éstos se han obtenido como resultado de la aplicación del modelo ASTER, desarrollado en el programa de Evaluación de los Recursos Hídricos procedentes de la Innivación (ERHIN), calibrado – entre otros- con datos de precipitaciones, temperatura y caudales provenientes a su vez del Sistema Automático de Información Hidrológica (SAIH). Ambos programas fueron implantados por la Administración en las diferentes Confederaciones Hidrográficas y en determinados Organismos de cuenca actuales, en cuyo desarrollo participó el autor de esta tesis. En cuanto a la zona de estudio se ha procedido a su elección considerando las posibles áreas de media montaña en las que la presencia de la nieve fuera hidrológicamente significativa y estuvieran constituidas litológicamente por afloramientos permeables que no impidieran la infiltración en el terreno y la formación de acuíferos de cierta relevancia. El interés se centró discrecionalmente en la cuenca del Tajo, tanto por el carácter estratégico de la misma -como suministradora en la actualidad de excedentes a otras cuencas deficitarias- como por el valor representativo de sus condiciones climáticas y orográficas en relación con otras cuencas hidrográficas peninsulares. Para ello se partió de las cabeceras de ríos identificadas por el programa ERHIN por su interés nivológico para la implantación del modelo ASTER y de las Masas de Agua Subterráneas MASb (antes Unidades Hidrogeológicas UUHH) definidas en los planes hidrológicos. La intersección en el territorio de ambos criterios condujo, finalmente, a la zona del Alto Tajo, en la que se cumplen ambos requisitos. El tramo quedó concretado en el comprendido entre las cabeceras de los ríos Tajo y Guadiela y la cola de los embalses de Entrepeñas y Buendía respectivamente, puntos de cierre para la calibración llevada a cabo en la modelización ASTER. Gran parte de éste discurre, en su parte alta, sobre rocas carbonatadas (calizas y dolomías del Jurásico y Cretácico), relacionados con las MASb de Tajuña-Montes Universales, Molina de Aragón y Sigüenza-Maranchón. Los valores diarios de las reservas de agua en forma de nieve, evapotranspiración y caudales procedentes de la fusión se han obtenido a partir de los resultados del mencionado modelo, procediéndose al cálculo de la infiltración por balance hídrico durante el periodo de estudio considerado, teniendo en cuenta los valores de precipitación, evapotranspiración y aportaciones de caudales. Esto ha requerido el estudio previo de las condiciones hidrogeológicas de la zona seleccionada con objeto de conocer las posibles interconexiones subterráneas que pudieran alterar los saldos entre las variables intervinientes anteriormente citadas. Para ello se ha llevado a cabo la recopilación y análisis de la información hidrogeológica correspondiente a la documentación de los planes hidrológicos del Tajo (Plan Hidrológico de la cuenca del Tajo RD 1664/1998 y el actual Plan Hidrológico de la parte española de la Demarcación Hidrográfica del Tajo RD 270/2014) y de los estudios previos realizados por el organismo de cuenca y el Instituto Geológico y Minero de España (lGME) fundamentalmente. En relación con la MASb Tajuña-Montes Universales -cuya extensión supera la zona seleccionada- dichos estudios consideran su estructura geológica y distribución litológica, con intercalaciones impermeables que actúan como barreras, dividiendo a éstas en Subunidades e identificando las zonas de drenaje de sus respectivos acuíferos. También se ha considerado la documentación y estudios previos del Plan Hidrológico Nacional sobre las Unidades Hidrogeológicas compartidas entre ámbitos geográficos de diferentes planes hidrológicos. Se concluye que las divisorias hidrográficas de las cabeceras son sensiblemente coincidentes o abarcan las Subunidades Montes Universales meridionales, Priego, Cifuentes, Zaorejas, u Montes Universales septentrionales, que drenan hacia el Tajo/Guadiela (bien directamente, bien a través de afluentes como el Gallo, Ablanquejo, Cabrillas, Cuervo…), MASb Molina de Aragón, que drena al Tajo a través del río Gallo y MASb Sigüenza—Maranchón, que drena su parte correspondiente hacia el Tajo a través del Ablanquejo. Se descartan – salvo la pequeña salvedad del manantial de Cifuentes- las conexiones hidrogeológicas con otras MASb o Subunidades por lo que las cabeceras del Tajo y del Guadiela pueden considerarse como un Sistema independiente donde las precipitaciones no evaporadas escurren superficialmente o se infiltran y descargan hacia los embalses de Entrepeñas y Buendía. La cuantificación diaria y acumulada de los balances hídricos ha permitido calcular la evolución aproximada de las reservas de agua subterránea desde la fecha inicial. Originalmente los balances se realizaron de forma separada en las cabeceras del Tajo y del Guadiela, cuyos valores acumulados manifestaron una tendencia creciente en la primera y decreciente en la segunda. Dicha situación se equilibra cuando el balance se practica conjuntamente en ambas, apreciándose en la variación del volumen de agua subterránea una evolución acorde hidrológicamente con los ciclos de verano/invierno y periodos de sequía, manteniéndose sus valores medios a largo/medio plazo, poniendo en evidencia la existencia de interconexiones subterráneas entre ambas cuencas. El balance conjunto, agregando la cabecera del Tajuña (que también comparte los materiales permeables de la MASb Tajuña-Montes Universales) no reveló la existencia de nuevas interrelaciones hidrogeológicas que influyeran en los balances hídricos realizados Tajo/Guadiela, confirmando las conclusiones de los estudios hidrogeológicos anteriormente analizados. Se ha procedido a confrontar y validar los resultados obtenidos de la evolución de las reservas de agua subterránea mediante los siguientes procedimientos alternativos: - Cálculo de los parámetros de desagüe de la curva de agotamiento correspondiente al volumen de agua subterránea drenante hacia el Tajo/Guadiela. Éste se ha realizado a partir de las aportaciones mensuales entrantes en los embalses de Entrepeñas y Buendía durante los meses de junio, julio, agosto y septiembre, cuyos valores responden al perfil típico de descargas de un acuífero. A partir de éstos se ha determinado el volumen drenante correspondiente al primero de junio de cada año de la serie histórica considerada. - Determinación del caudal base por el método Wallingford y deducción de los volúmenes drenantes. Estimación de las recarga anuales - Cuantificación de la recarga anual por el método Sanz, Menéndez Pidal de Navascués y Távara. Se obtuvieron valores de recarga muy aproximados entre los calculados por los dos últimos procedimientos citados. Respecto a las reservas de agua subterránea almacenadas siguen una evolución semejante en todos los casos, lo que ha permitido considerar válidos los resultados conseguidos mediante balance hídrico. Confirmada su solidez, se han buscado correlaciones simples entre el volumen de las reservas subterráneas (como indicador estimativo del efecto de la infiltración) y los volúmenes procedentes de la fusión. La conclusión es que estos últimos no tienen un efecto determinante a escala anual sobre la infiltración,recarga y variación de los volúmenes de agua subterránea, frente al peso de otras variables (precipitación y evapotranspiración). No obstante se ha encontrado una buena correlación múltiple entre la recarga estimada y la precipitación eficaz (precipitación menos evapotranspiración) y fusión, que ha permitido cuantificar la contribución de esta última. Posteriormente se ha recurrido a la selección de los episodios más intensos de acumulación /fusión en las cabeceras del Tajo y Guadiela. Y se procedió a la comparación entre los resultados obtenidos por aplicación del modelo de simulación en los mismos periodos (normalmente de varios días de duración) con datos reales y con datos ficticios de temperatura que anularan o disminuyeran la presencia de nieve, apreciándose una gran sensibilidad del efecto de la temperatura sobre la evapotranspiración y estableciéndose nuevamente correlaciones lineales entre los volúmenes de fusión y el incremento de reservas subterráneas. Las mismas confirman el efecto “favorecedor” de la acumulación de agua en forma de nieve y su posterior licuación, sobre sobre la infiltración de agua en el suelo y almacenamiento subterráneo. Finalmente se establecieron varios escenarios climáticos (+1ºC; +3ºC; +1ºC y – 10% precipitación; y 3ºC – 10% precipitación) compatibles con las previsiones del IPCC para mediados y finales del presente siglo, determinándose mediante simulación ASTER los correspondientes valores de fusión. La correlación establecida a escala anual ha permitido evaluar el efecto de la disminución del volumen de fusión - en los diferentes escenarios – sobre la recarga, pronosticando un descenso de los caudales de estiaje y la desaparición del “efecto nieve” sobre la infiltración y recarga con un aumento de 3ºC de temperatura. Teniendo en cuenta las condiciones de representatividad de la zona elegida, resulta verosímil la extensión de las anteriores conclusiones a otras cabeceras fluviales enclavadas en áreas de media montaña situadas entre 1000 a 2000m y sus efectos aguas abajo.Water infiltration into the soil and groundwater recharge deep water in aquifers is slow relative to other hydrological phenomena. The wording of this thesis aims to contribute to the study of the influence that the storage of solid precipitation as snow cover and its eventual melting may have on this process in mid-mountain areas (1000 - 2,000 m) where very often the headwaters of the peninsular rivers are located. For this party analysis of the different variables involved has over a given time period and a particular geographical area, so that their methodology is empirical in nature. The extension of the period (2002/03 to 2010/11) has been conditioned by the availability of the values of some of its key variables, as were the water equivalent of the snow and flows from melting. These have been obtained as a result of the application of ASTER model, developed in the program Evaluation of Water Resources from the Innivation (ERHIN), calibrated - among others data of rainfall, temperature and flow from turn System Automatic Hydrological Information (SAIH). Both programs were implemented by the Administration in the different Water Boards and to undertakings for current basin, in which the author participated development of this thesis. As for the study area has proceeded at its option considering the possible areas of midmountain in the presence of snow outside hydrological meaningful and they were lithology consisting of permeable outcrops that did not prevent infiltration into the ground and forming aquifers of some significance. We were interested discretion in the Tagus basin, therefore the strategic nature of it, as currently supplying surplus to other basins deficit- as the representative value of its climate and terrain conditions in relation to other peninsular river basins . To do this we started from the headwaters identified by the ERHIN program for its implementation snow interest to the ASTER model and Ground Water Bodies MASb (before UUHH Hydrogeological Units) defined in hydrological plans. The intersection in the territory of both criteria led eventually to the Alto Tajo, in which both requirements are met. The section was finalized in the period between the headwaters of the Tagus and Guadiela rivers and reservoirs end Entrepeñas and Buendia respectively checking points for calibration performed in ASTER modeling. Much of it runs on carbonate rocks (limestones and dolomites of Jurassic and Cretaceous) related MASb of Tajuña -Montes Universal, Molina de Aragón and Sigüenza-Maranchón. The daily values of water reserves in the form of snow, evapotranspiration and flow from melting were obtained from the results of this model, proceeding to the calculation of infiltration water balance during the study period considered, taking into account values of precipitation, evapotranspiration and input flow. This has required the prior examination of the hydrogeological conditions of your required in order to know the possible underground interconnections that could alter the balance between the intervening variables aforementioned area. For this we have carried out the collection and analysis of hydrogeological information relevant documentation Tagus river management plans (Hydrological Plan Tajo Basin RD 1664/1998 and the current Hydrological Plan of the Spanish part of the River Basin Tagus RD 270/2014) and previous studies by the basin organization and the Geological Survey of Spain (IGME) mainly. Regarding the MASb Tajuña- Montes Universal - whose length exceeds the area selected - these studies consider its geological structure and lithology distribution with waterproof collations that act as barriers, dividing it into subunits and identifying areas draining their respective aquifers. It has also considered the documentation and previous studies of the National Hydrological Plan on shared among different geographical areas management plans Hydrogeological Units. We conclude that river dividing the headers are substantially coincident or covering Subunits southern Universal Montes, Priego Cifuentes, Zaorejas and northern Universal Mounts, which drain into the Tagus / Guadiela (either directly or through tributaries such as Gallo, Ablanquejo , whitecaps , Raven ...), MASb Molina de Aragón which drains through the Tajo del Gallo and MASb Sigüenza- Maranchón river that drains into the Tagus using the Ablanquejo . Discarded - except the small exception of spring Cifuentes -hydrogeological connections with other MASb or Subunits so the headwaters of the Tagus and Guadiela be considered as a separate system, where rainfall not evaporated runs on surface or infiltrates and eventually discharged into reservoirs Entrepeñas and Buendia. The daily and cumulative quantification of water balances allowed us to compute the approximate evolution of groundwater reserves from its initial date. Initially balances were performed separately in the headwaters of the Tagus and Guadiela, whose cumulative values showed an increasing trend in the first and decreasing in the second. This situation is balanced when the balance is practiced together in both , appreciating the change in volume of groundwater hydrological evolution commensurate with the cycles of summer / winter and drought periods , keeping their average long / medium term values and putting in shows the existence of underground interconnections between the two basins. The overall balance, adding header Tajuña (which also shares the permeable materials MASb Tajuña -Montes Universal ) did not reveal the existence of new hydrogeological interrelationships that influenced water balances made Tajo / Guadiela, confirming the findings of the hydrogeological studies previously analyzed. We proceeded to confront and validate the results of the evolution of groundwater reserves by the following alternative procedures: - Calculate the parameters drain depletion curve corresponding to the volume of groundwater draining into the Tajo / Guadiela. This has been made from monthly inflows in the reservoirs of Entrepeñas and Buendia during the months of June, July, August and September, whose values match the typical profile of an aquifer discharges. From these has been determined for the first of June each year of the time series considered drainage volume - Determination of base flow by Wallingford method and deduction of drainage volumes. Estimate of annual recharge - Quantification of the annual recharge by the method Sanz Menéndez Pidal of Navascués and Távara. Very approximate values recharge between calculated for the last two mentioned methods were obtained. Concerning groundwater reserves stored follow a similar pattern in all cases, allowing consider valid the results achieved through water balance. Confirmed its robustness, simple correlations were sought between the volume of groundwater reserves (as estimated indicator of the effect of infiltration) and volumes from the melting. The conclusion is that the latter do not have a decisive effect on the annual scale infiltration, recharge and variation in volumes of groundwater, against the weight of other variables (precipitation and evapotranspiration). However found a good multiple correlation between the estimated recharge and effective precipitation (precipitation minus evapotranspiration) and fusion, which allowed quantify the contribution of the latter. Subsequently it has resorted to the selection of the most intense episodes of accumulation / melting in the headwaters of the Tagus and Guadiela. And we proceeded to the comparison between the results obtained by application of the simulation model in the same periods (usually several days) with real data and fictitious temperature data to annul or decrease the presence of snow, appreciating a great sensitivity of the effect of temperature on evapotranspiration and establishing linear correlations between the volumes of melting and increased groundwater reserves again. They confirm the “flattering " effect of water accumulation as snow and subsequent liquefaction of the infiltration of water into the soil and underground storage. Finally various climate scenarios (+1ºC; +3ºC; +1ºC y – 10% precipitation; y 3ºC – 10% precipitation) were established consistent with IPCC projections for mid - to late - century, determined through simulation ASTER corresponding values of melting. The correlation established on an annual scale has allowed to evaluate the effect of decreasing the volume of melt - in different scenarios - on recharge, predicting a decline in low flows and the disappearance of "snow effect" on infiltration and recharge with an increase of 3°C temperature. Given the conditions of representativeness of the chosen area, plausible extension of the above findings to other landlocked headwaters in mid-mountain areas located between 1000 to 2000m and its downstream effects.

Global Stability Analysis of Turbulent Transonic Flows on Airfoil geometries

La aparición de inestabilidades en un flujo es un problema importante que puede afectar a algunas aplicaciones aerodinámicas. De hecho existen diferentes tipos de fenómenos no-estacionarios que actualmente son tema de investigación; casos como la separación a altos ángulos de ataque o el buffet transónico son dos ejemplos de cierta relevancia. El análisis de estabilidad global permite identificar la aparición de dichas condiciones inestables, proporcionando información importante sobre la región donde la inestabilidad es dominante y sobre la frecuencia del fenómeno inestable. La metodología empleada es capaz de calcular un flujo base promediado mediante una discretización con volúmenes finitos y posteriormente la solución de un problema de autovalores asociado a la linealización que aparece al perturbar el flujo base. El cálculo numérico se puede dividir en tres pasos: primero se calcula una solución estacionaria para las ecuaciones RANS, luego se extrae la matriz del Jacobiano que representa el problema linealizado y finalmente se deriva y se resuelve el problema de autovalores generalizado mediante el método iterativo de Arnoldi. Como primer caso de validación, la técnica descrita ha sido aplicada a un cilindro circular en condiciones laminares para detectar el principio de las oscilaciones de los vórtices de von Karman, y se han comparado los resultados con experimentos y cálculos anteriores. La parte más importante del estudio se centra en el análisis de flujos compresibles en régimen turbulento. La predicción de la aparición y la progresión de flujo separado a altos ángulos de ataque se han estudiado en el perfil NACA0012 en condiciones tanto subsónicas como supersónicas y en una sección del ala del A310 en condiciones de despegue. Para todas las geometrías analizadas, se ha podido observar que la separación gradual genera la aparición de un modo inestable específico para altos ángulos de ataque siempre mayores que el ángulo asociado al máximo coeficiente de sustentación. Además, se ha estudiado el problema adjunto para obtener información sobre la zona donde una fuerza externa provoca el máximo cambio en el campo fluido. El estudio se ha completado calculando el mapa de sensibilidad estructural y localizando el centro de la inestabilidad. En el presente trabajo de tesis se ha analizado otro importante fenómeno: el buffet transónico. En condiciones transónicas, la interacción entre la onda de choque y la capa límite genera una oscilación de la posición de la onda de choque y, por consiguiente, de las fuerzas aerodinámicas. El conocimiento de las condiciones críticas y su origen puede ayudar a evitar la oscilación causada por estas fuerzas. Las condiciones para las cuales comienza la inestabilidad han sido calculadas y comparadas con trabajos anteriores. Por otra parte, los resultados del correspondiente problema adjunto y el mapa de sensibilidad se han obtenido por primera vez para el buffet, indicando la región del dominio que sera necesario modificar para crear el mayor cambio en las propiedades del campo fluido. Dado el gran consumo de memoria requerido para los casos 3D, se ha realizado un estudio sobre la reducción del domino con la finalidad de reducirlo a la región donde está localizada la inestabilidad. La eficacia de dicha reducción de dominio ha sido evaluada investigando el cambio en la dimensión de la matriz del Jacobiano, no resultando muy eficiente en términos del consumo de memoria. Dado que el buffet es un problema en general tridimensional, el análisis TriGlobal de una geometría 3D podría considerarse el auténtico reto futuro. Como aproximación al problema, un primer estudio se ha realizado empleando una geometría tridimensional extruida del NACA00f2. El cálculo del flujo 3D y, por primera vez en casos tridimensionales compresibles y turbulentos, el análisis de estabilidad TriGlobal, se han llevado a cabo. La comparación de los resultados obtenidos con los resultados del anterior modelo 2D, ha permitido, primero, verificar la exactitud del cálculo 2D realizado anteriormente y también ha proporcionado una estimación del consumo de memoria requerido para el caso 3D. ABSTRACT Flow unsteadiness is an important problem in aerodynamic applications. In fact, there are several types of unsteady phenomena that are still at the cutting edge of research in the field; separation at high angles of attack and transonic buffet are two important examples. Global Stability Analysis can identify the unstable onset conditions, providing important information about the instability location in the domain and the frequency of the unstable phenomenon. The methodology computes a base flow averaged state based on a finite volume discretization and a solution for a generalized eigenvalue problem corresponding to the perturbed linearized equations. The numerical computation is then performed in three steps: first, a steady solution for the RANS equation is computed; second, the Jacobian matrix that represents the linearized problem is obtained; and finally, the generalized eigenvalue problem is derived and solved with an Arnoldi iterative method. As a first validation test, the technique has been applied on a laminar circular cylinder in order to detect the von Karman vortex shedding onset, comparing the results with experiments and with previous calculations. The main part of the study focusses on turbulent and compressible cases. The prediction of the origin and progression of separated flows at high angles of attack has been studied on the NACA0012 airfoil at subsonic and transonic conditions and for the A310 airfoil in take-off configuration. For all the analyzed geometries, it has been found that gradual separation generates the appearance of one specific unstable mode for angles of attack always greater than the ones related to the maximum lift coefficient. In addition, the adjoint problem has been studied to suggest the location of an external force that results in the largest change to the flow field. From the direct and the adjoint analysis the structural sensitivity map has been computed and the core of the instability has been located. The other important phenomenon analyzed in this work is the transonic buffet. In transonic conditions, the interaction between the shock wave and the boundary layer leads to an oscillation of the shock location and, consequently, of the aerodynamic forces. Knowing the critical operational conditions and its origin can be helpful in preventing such fluctuating forces. The instability onset has then been computed and compared with the literature. Moreover, results of the corresponding adjoint problem and a sensitivity map have been provided for the first time for the buffet problem, indicating the region that must be modified to create the biggest change in flow field properties. Because of the large memory consumption required when a 3D case is approached, a domain reduction study has been carried out with the aim of limiting the domain size to the region where the instability is located. The effectiveness of the domain reduction has been evaluated by investigating the change in the Jacobian matrix size, not being very efficient in terms of memory consumption. Since buffet is a three-dimensional problem, TriGlobal stability analysis can be seen as a future challenge. To approximate the problem, a first study has been carried out on an extruded three-dimensional geometry of the NACA0012 airfoil. The 3D flow computation and the TriGlobal stability analysis have been performed for the first time on a compressible and turbulent 3D case. The results have been compared with a 2D model, confirming that the buffet onset evaluated in the 2D case is well detected. Moreover, the computation has given an indication about the memory consumption for a 3D case.

Discrete linear stability and sensitivity analysis of fluid flows

Este trabajo presenta un método discreto para el cálculo de estabilidad hidrodinámica y análisis de sensibilidad a perturbaciones externas para ecuaciones diferenciales y en particular para las ecuaciones de Navier-Stokes compressible. Se utiliza una aproximación con variable compleja para obtener una precisión analítica en la evaluación de la matriz Jacobiana. Además, mapas de sensibilidad para la sensibilidad a las modificaciones del flujo de base y a una fuerza constante permiten identificar las regiones del campo fluido donde una modificacin (ej. fuerza puntual) tiene un efecto estabilizador del flujo. Se presentan cuatro casos de prueba: (1) un caso analítico para comprobar la derivación discreta, (2) una cavidad cerrada a bajo Reynolds para mostrar la mayor precisión en el cálculo de los valores propios con la aproximación de paso complejo, (3) flujo 2D en un cilindro circular para validar la metodología, y (4) flujo en un cavidad abierta, presentado para validar el método en casos de inestabilidades convectivamente inestables. Los tres últimos casos mencionados (2-4) se resolvieron con las ecuaciones de Navier-Stokes compresibles, utilizando un método Discontinuous Galerkin Spectral Element Method. Se obtuvo una buena concordancia para el caso de validación (3), cuando se comparó el nuevo método con resultados de la literatura. Además, este trabajo muestra que para el cálculo de los modos propios directos y adjuntos, así como para los mapas de sensibilidad, el uso de variables complejas es de suprema importancia para obtener una predicción precisa. El método descrito es aplicado al análisis para la estabilización de la estela generada por un disco actuador, que representa un modelo sencillo para hélices, rotores de helicópteros o turbinas eólicas. Se explora la primera bifurcación del flujo para un disco actuador, y se sugiere que está asociada a una inestabilidad de tipo Kelvin-Helmholtz, cuya estabilidad se controla con en el número de Reynolds y en la resistencia del disco actuador (o fuerza resistente). En primer lugar, se verifica que la disminución de la resistencia del disco tiene un efecto estabilizador parecido a una disminución del Reynolds. En segundo lugar, el análisis hidrodinmico discreto identifica dos regiones para la colocación de una fuerza puntual que controle las inestabilidades, una cerca del disco y otra en una zona aguas abajo. En tercer lugar, se muestra que la inclusión de un forzamiento localizado cerca del actuador produce una estabilización más eficiente que al forzar aguas abajo. El análisis de los campos de flujo controlados confirma que modificando el gradiente de velocidad cerca del actuador es más eficiente para estabilizar la estela. Estos resultados podrían proporcionar nuevas directrices para la estabilización de la estela de turbinas de viento o de marea cuando estén instaladas en un parque eólico y minimizar las interacciones no estacionarias entre turbinas. ABSTRACT A discrete framework for computing the global stability and sensitivity analysis to external perturbations for any set of partial differential equations is presented. In particular, a complex-step approximation is used to achieve near analytical accuracy for the evaluation of the Jacobian matrix. Sensitivity maps for the sensitivity to base flow modifications and to a steady force are computed to identify regions of the flow field where an input could have a stabilising effect. Four test cases are presented: (1) an analytical test case to prove the theory of the discrete framework, (2) a lid-driven cavity at low Reynolds case to show the improved accuracy in the calculation of the eigenvalues when using the complex-step approximation, (3) the 2D flow past a circular cylinder at just below the critical Reynolds number is used to validate the methodology, and finally, (4) the flow past an open cavity is presented to give an example of the discrete method applied to a convectively unstable case. The latter three (2–4) of the aforementioned cases were solved with the 2D compressible Navier–Stokes equations using a Discontinuous Galerkin Spectral Element Method. Good agreement was obtained for the validation test case, (3), with appropriate results in the literature. Furthermore, it is shown that for the calculation of the direct and adjoint eigenmodes and their sensitivity maps to external perturbations, the use of complex variables is paramount for obtaining an accurate prediction. An analysis for stabilising the wake past an actuator disc, which represents a simple model for propellers, helicopter rotors or wind turbines is also presented. We explore the first flow bifurcation for an actuator disc and it suggests that it is associated to a Kelvin- Helmholtz type instability whose stability relies on the Reynolds number and the flow resistance applied through the disc (or actuator forcing). First, we report that decreasing the disc resistance has a similar stabilising effect to an decrease in the Reynolds number. Second, a discrete sensitivity analysis identifies two regions for suitable placement of flow control forcing, one close to the disc and one far downstream where the instability originates. Third, we show that adding a localised forcing close to the actuator provides more stabilisation that forcing far downstream. The analysis of the controlled flow fields, confirms that modifying the velocity gradient close to the actuator is more efficient to stabilise the wake than controlling the sheared flow far downstream. An interesting application of these results is to provide guidelines for stabilising the wake of wind or tidal turbines when placed in an energy farm to minimise unsteady interactions.

Lithogeochemistry and fluid flow in the epithermal Veta Rublo base metal-silver deposit, Chonta Mine (Huancavelica, Perú)

The Chonta Mine (75º00’30” W & 13º04’30”S, 4495 to 5000 m absl), owned by Compañía Minera Caudalosa, operates a polymetallic Zn-Pb-Cu-Ag vein system of the low sulphidation epithermal type, hosted by cenozoic volcanics of dacitic to andesitic composition (Domos de Lava Formation). Veta Rublo, one of the main veins of the system, is worked underground to nearly 300 m. It strikes 60-80º NE and dips 60-70º SE; its width varies between 0.30 and 2.20m, and it crops out along 1 km, but is continued along strike by other veins, as Veta Caudalosa, for some 5 km. Typical metal contents are 7% Zn, 5% Pb, 0.4% Cu and 3 oz/t Ag, with quartz, sericite, sphalerite, galena, pyrite, chalcopyrite, fahlore as main minerals, and minor carbonate and sulphosalts.

Proposal of an Alternative Model for Speed-Flow Relationship in Two-Lane Highways

A research has been carried out in two-lanehighways in the Madrid Region to propose an alternativemodel for the speed-flowrelationship using regular loop data. The model is different in shape and, in some cases, slopes with respect to the contents of Highway Capacity Manual (HCM). A model is proposed for a mountainous area road, something for which the HCM does not provide explicitly a solution. The problem of a mountain road with high flows to access a popular recreational area is discussed, and some solutions are proposed. Up to 7 one-way sections of two-lanehighways have been selected, aiming at covering a significant number of different characteristics, to verify the proposed method the different classes of highways on which the Manual classifies them. In order to enunciate the model and to verify the basic variables of these types of roads a high number of data have been used. The counts were collected in the same way that the Madrid Region Highway Agency performs their counts. A total of 1.471 hours have been collected, in periods of 5 minutes. The models have been verified by means of specific statistical test (R2, T-Student, Durbin-Watson, ANOVA, etc.) and with the diagnostics of the contrast of assumptions (normality, linearity, homoscedasticity and independence). The model proposed for this type of highways with base conditions, can explain the different behaviors as traffic volumes increase, and follows a polynomial multiple regression model of order 3, S shaped. As secondary results of this research, the levels of service and the capacities of this road have been measured with the 2000 HCM methodology, and the results discussed. © 2011 Published by Elsevier Ltd.

Flow and fracture behaviour of high performance alloys

Based on our needs, that is to say, through precise simulation of the impact phenomena that may occur inside a jet engine turbine with an explicit non-linear finite element code, four new material models are postulated. Each one of is calibrated for four high-performance alloys that can be encountered in a modern jet engine. A new uncoupled material model for high strain and ballistic is proposed. Based on a Johnson-Cook type model, the proposed formulation introduces the effect of the third deviatoric invariant by means of three different Lode angle dependent functions. The Lode dependent functions are added to both plasticity and failure models. The postulated model is calibrated for a 6061-T651 aluminium alloy with data taken from the literature. The fracture pattern predictability of the JCX material model is shown performing numerical simulations of various quasi-static and dynamic tests. As an extension of the above-mentioned model, a modification in the thermal softening behaviour due to phase transformation temperatures is developed (JCXt). Additionally, a Lode angle dependent flow stress is defined. Analysing the phase diagram and high temperature tests performed, phase transformation temperatures of the FV535 stainless steel are determined. The postulated material model constants for the FV535 stainless steel are calibrated. A coupled elastoplastic-damage material model for high strain and ballistic applications is presented (JCXd). A Lode angle dependent function is added to the equivalent plastic strain to failure definition of the Johnson-Cook failure criterion. The weakening in the elastic law and in the Johnson-Cook type constitutive relation implicitly introduces the Lode angle dependency in the elastoplastic behaviour. The material model is calibrated for precipitation hardened Inconel 718 nickel-base superalloy. The combination of a Lode angle dependent failure criterion with weakened constitutive equations is proven to predict fracture patterns of the mechanical tests performed and provide reliable results. A transversely isotropic material model for directionally solidified alloys is presented. The proposed yield function is based a single linear transformation of the stress tensor. The linear operator weighs the degree of anisotropy of the yield function. The elastic behaviour, as well as the hardening, are considered isotropic. To model the hardening, a Johnson-Cook type relation is adopted. A material vector is included in the model implementation. The failure is modelled with the Cockroft-Latham failure criterion. The material vector allows orienting the reference orientation in any other that the user may need. The model is calibrated for the MAR-M 247 directionally solidified nickel-base superalloy.