Asymmetric amplification in amino acid sublimation involving racemic compound to conglomerate conversion

A straightforward unprecedented sublimation protocol that reveals both conversion of a racemic compound into a racemic conglomerate and subsequent enantioenrichment has been developed for the proteinogenic amino acid valine. The phenomenon has been observed in closed and open systems, providing insight into asymmetric amplification mechanisms under presumably prebiotic conditions

Study of the II Network as the Compound Slot Equivalent Circuit Model

A combination of Method of Moments (MoM) and compound slot Equivalent Circuit Model for linear array design is presented in this document. From the S Matrix of the single element, the more suitable network for its characterization is analyzed and selected. Then according to the radiation requirements of the desired array, the elements are designed and then properly connected by means of Forward Matching Procedure (FMP), which takes into account impedance matters in order to keep the input matched at the designing frequency. Comparison between HFSS simulations and MoM-FMP results are also presented. First part of this work was introduced in (1)(2) but a summary is included here to make the understanding easier.

Contribution to the design of waveguide-fed compound-slot arrays by means of equivalent circuit modelling

Los arrays de ranuras son sistemas de antennas conocidos desde los años 40, principalmente destinados a formar parte de sistemas rádar de navíos de combate y grandes estaciones terrenas donde el tamaño y el peso no eran altamente restrictivos. Con el paso de los años y debido sobre todo a importantes avances en materiales y métodos de fabricación, el rango de aplicaciones de este tipo de sistemas radiantes creció en gran medida. Desde nuevas tecnologías biomédicas, sistemas anticolisión en automóviles y navegación en aviones, enlaces de comunicaciones de alta tasa binaria y corta distancia e incluso sistemas embarcados en satélites para la transmisión de señal de televisión. Dentro de esta familia de antennas, existen dos grupos que destacan por ser los más utilizados: las antennas de placas paralelas con las ranuras distribuidas de forma circular o espiral y las agrupaciones de arrays lineales construidos sobre guia de onda. Continuando con las tareas de investigación desarrolladas durante los últimos años en el Instituto de Tecnología de Tokyo y en el Grupo de Radiación de la Universidad Politécnica de Madrid, la totalidad de esta tesis se centra en este último grupo, aunque como se verá se separa en gran medida de las técnicas de diseño y metodologías convencionales. Los arrays de ranuras rectas y paralelas al eje de la guía rectangular que las alimenta son, sin ninguna duda, los modelos más empleados debido a la fiabilidad que presentan a altas frecuencias, su capacidad para gestionar grandes cantidades de potencia y la sencillez de su diseño y fabricación. Sin embargo, también presentan desventajas como estrecho ancho de banda en pérdidas de retorno y rápida degradación del diagrama de radiación con la frecuencia. Éstas son debidas a la naturaleza resonante de sus elementos radiantes: al perder la resonancia, el sistema global se desajusta y sus prestaciones degeneran. En arrays bidimensionales de slots rectos, el campo eléctrico queda polarizado sobre el plano transversal a las ranuras, correspondiéndose con el plano de altos lóbulos secundarios. Esta tesis tiene como objetivo el desarrollo de un método sistemático de diseño de arrays de ranuras inclinadas y desplazadas del centro (en lo sucesivo “ranuras compuestas”), definido en 1971 como uno de los desafíos a superar dentro del mundo del diseño de antennas. La técnica empleada se basa en el Método de los Momentos, la Teoría de Circuitos y la Teoría de Conexión Aleatoria de Matrices de Dispersión. Al tratarse de un método circuital, la primera parte de la tesis se corresponde con el estudio de la aplicabilidad de las redes equivalentes fundamentales, su capacidad para recrear fenómenos físicos de la ranura, las limitaciones y ventajas que presentan para caracterizar las diferentes configuraciones de slot compuesto. Se profundiza en las diferencias entre las redes en T y en ! y se condiciona la selección de una u otra dependiendo del tipo de elemento radiante. Una vez seleccionado el tipo de red a emplear en el diseño del sistema, se ha desarrollado un algoritmo de cascadeo progresivo desde el puerto alimentador hacia el cortocircuito que termina el modelo. Este algoritmo es independiente del número de elementos, la frecuencia central de funcionamiento, del ángulo de inclinación de las ranuras y de la red equivalente seleccionada (en T o en !). Se basa en definir el diseño del array como un Problema de Satisfacción de Condiciones (en inglés, Constraint Satisfaction Problem) que se resuelve por un método de Búsqueda en Retroceso (Backtracking algorithm). Como resultado devuelve un circuito equivalente del array completo adaptado a su entrada y cuyos elementos consumen una potencia acorde a una distribución de amplitud dada para el array. En toda agrupación de antennas, el acoplo mutuo entre elementos a través del campo radiado representa uno de los principales problemas para el ingeniero y sus efectos perjudican a las prestaciones globales del sistema, tanto en adaptación como en capacidad de radiación. El empleo de circuito equivalente se descartó por la dificultad que suponía la caracterización de estos efectos y su inclusión en la etapa de diseño. En esta tesis doctoral el acoplo también se ha modelado como una red equivalente cuyos elementos son transformadores ideales y admitancias, conectada al conjunto de redes equivalentes que representa el array. Al comparar los resultados estimados en términos de pérdidas de retorno y radiación con aquellos obtenidos a partir de programas comerciales populares como CST Microwave Studio se confirma la validez del método aquí propuesto, el primer método de diseño sistemático de arrays de ranuras compuestos alimentados por guía de onda rectangular. Al tratarse de ranuras no resonantes, el ancho de banda en pérdidas de retorno es mucho mas amplio que el que presentan arrays de slots rectos. Para arrays bidimensionales, el ángulo de inclinación puede ajustarse de manera que el campo quede polarizado en los planos de bajos lóbulos secundarios. Además de simulaciones se han diseñado, construido y medido dos prototipos centrados en la frecuencia de 12GHz, de seis y diez elementos. Las medidas de pérdidas de retorno y diagrama de radiación revelan excelentes resultados, certificando la bondad del método genuino Method of Moments - Forward Matching Procedure desarrollado a lo largo de esta tésis. Abstract The slot antenna arrays are well known systems from the decade of 40s, mainly intended to be part of radar systems of large warships and terrestrial stations where size and weight were not highly restrictive. Over the years, mainly due to significant advances in materials and manufacturing methods, the range of applications of this type of radiating systems grew significantly. From new biomedical technologies, collision avoidance systems in cars and aircraft navigation, short communication links with high bit transfer rate and even embedded systems in satellites for television broadcast. Within this family of antennas, two groups stand out as being the most frequent in the literature: parallel plate antennas with slots placed in a circular or spiral distribution and clusters of waveguide linear arrays. To continue the vast research work carried out during the last decades in the Tokyo Institute of Technology and in the Radiation Group at the Universidad Politécnica de Madrid, this thesis focuses on the latter group, although it represents a technique that drastically breaks with traditional design methodologies. The arrays of slots straight and parallel to the axis of the feeding rectangular waveguide are without a doubt the most used models because of the reliability that they present at high frequencies, its ability to handle large amounts of power and their simplicity of design and manufacturing. However, there also exist disadvantages as narrow bandwidth in return loss and rapid degradation of the radiation pattern with frequency. These are due to the resonant nature of radiating elements: away from the resonance status, the overall system performance and radiation pattern diminish. For two-dimensional arrays of straight slots, the electric field is polarized transverse to the radiators, corresponding to the plane of high side-lobe level. This thesis aims to develop a systematic method of designing arrays of angled and displaced slots (hereinafter "compound slots"), defined in 1971 as one of the challenges to overcome in the world of antenna design. The used technique is based on the Method of Moments, Circuit Theory and the Theory of Scattering Matrices Connection. Being a circuitry-based method, the first part of this dissertation corresponds to the study of the applicability of the basic equivalent networks, their ability to recreate the slot physical phenomena, their limitations and advantages presented to characterize different compound slot configurations. It delves into the differences of T and ! and determines the selection of the most suitable one depending on the type of radiating element. Once the type of network to be used in the system design is selected, a progressive algorithm called Forward Matching Procedure has been developed to connect the proper equivalent networks from the feeder port to shorted ending. This algorithm is independent of the number of elements, the central operating frequency, the angle of inclination of the slots and selected equivalent network (T or ! networks). It is based on the definition of the array design as a Constraint Satisfaction Problem, solved by means of a Backtracking Algorithm. As a result, the method returns an equivalent circuit of the whole array which is matched at its input port and whose elements consume a power according to a given amplitude distribution for the array. In any group of antennas, the mutual coupling between elements through the radiated field represents one of the biggest problems that the engineer faces and its effects are detrimental to the overall performance of the system, both in radiation capabilities and return loss. The employment of an equivalent circuit for the array design was discarded by some authors because of the difficulty involved in the characterization of the coupling effects and their inclusion in the design stage. In this thesis the coupling has also been modeled as an equivalent network whose elements are ideal transformers and admittances connected to the set of equivalent networks that represent the antennas of the array. By comparing the estimated results in terms of return loss and radiation with those obtained from popular commercial software as CST Microwave Studio, the validity of the proposed method is fully confirmed, representing the first method of systematic design of compound-slot arrays fed by rectangular waveguide. Since these slots do not work under the resonant status, the bandwidth in return loss is much wider than the longitudinal-slot arrays. For the case of two-dimensional arrays, the angle of inclination can be adjusted so that the field is polarized at the low side-lobe level plane. Besides the performed full-wave simulations two prototypes of six and ten elements for the X-band have been designed, built and measured, revealing excellent results and agreement with the expected results. These facts certify that the genuine technique Method of Moments - Matching Forward Procedure developed along this thesis is valid and trustable.

Influence of some oenological practices on the aromatic and sensorial characteristics of white Verdejo wines

Changes in the aromatic composition as well as sensory characteristics in Verdejo white wines were analysed based on two factors: the winemaking methodology and the storing time of wine in bottles. The volatile components were determined by GLC-MS, and the sensory profile was designed and assessed according to the ISO 11035 standard. The results showed that when wines were made in oak barrels, either completely or partially, which means the wines were in contact with the lees, the levels of 1-octanol, ethyl heptanoate and ethyl decanoate were significantly affected (P menor que 0.05); the softness sensation was also influenced (P menor que 0.05). However, the amount of time the wines were stored in bottles significantly affected (P menor que 0.05) the levels of 1-hexanol, ethyl heptanoate, ethyl octanoate, ethyl decanoate, hexyl acetate, isoamyl acetate and isoamyl lactate and also an odour note (tropical fruit). The compounds with higher OAV values belong to the groups of esters and fatty acids. For these reasons, the composition and the quality of the aroma of Verdejo white wines appear to be significantly affected both by use of oak barrels in winemaking and the time the wines are stored in bottles.

Improvement of compatibility and stability on polyethylene-modified bitumen by use of an aromatic extra as compatibilizer.

Bitumen modification by polyethylene addition usually improves the mechanical properties of the binder and, therefore, the behavior in service of the bituminous mix: thermal susceptibility and rutting can be diminished, whilst the resistance to low temperature cracking may increase. To achieve this improvement it is necessary a good compatibility between the base bitumen and the polyethylene. Low compatibility between bitumen and polyethylene can lead to phase separation: the polymer- asphalt incompatibility translates into a deterioration of ultimate properties. The object of this research project was to determine if these problems can be diminished by using certain compatibilizer agents, e.g. an aromatic extract from the oil refinery. Compatibility and stability of the polyethylene modified bitumen were studied using conventional test methods and dynamic shear reometer (DSR). Blends of bitumen and polyethylene were prepared with neat bitumen (PMB) or bitumen with compatibilizer as component of the binder (PMBC) and then compared. The experimental results show that “colloid instability index”(IC) is a parameter that can be used to control the compatibility between bitumen and polyethylene. From polyethylene point of view, one of the parameters that govern is the “melt flow index” (MFI). Experimental results show that PMBC formulated with low IC bitumen and hi gh MFI lineal polyethylene can be considered as stable binder.

Optimización de parámetros fermentativos de calidad en vinos tintos de zonas cálidas

El aumento progresivo de la temperatura media anual y el déficit hídrico están provocando importantes cambios en la composición y la maduración de la uva, que repercuten directamente sobre el proceso fermentativo y, por ende, sobre la calidad del vino elaborado. En este trabajo se evalúan diferentes estrategias para la reducción del grado alcohólico, la mejora del color del vino y su estabilidad, y el incremento y la persistencia aromática. Mediante el empleo de levaduras con ineficiencia glicolítica se lograron reducciones medias en el grado alcohólico de entre 0.3 y 1.7 % v/v, mientras que con las fermentaciones secuenciales la máxima reducción lograda fue de 3.3 y 3.4 % v/v al combinar las cepas 938 (Schizosaccharomyces pombe) y 7013 (Torulaspora delbrueckii) con la 7VA (Saccharomyces cerevisiae). Al aplicar un tratamiento térmico sobre el inóculo, la TP2A(16) mostró una reducción media significativa en el grado alcohólico de 1 % v/v. El principal inconveniente en todas las técnicas empleadas para reducir el grado alcohólico fue la falta de repetibilidad en los resultados obtenidos. Por otra parte, la aplicación de altas presiones sobre uva despalillada resultó efectiva como tratamiento de pasteurización y como potenciador de la extracción de polifenoles, logrando un incremento en el contenido medio de antocianos totales del 12.4-18.5 %. La adición de flavonoides al mosto estimuló la formación de pigmentos estables como resultado de su condensación con antocianos mediada por acetaldehído. Con el empleo de Torulaspora delbrueckii en fermentación secuencial fue posible incrementar la producción de diacetilo y acetato de 2-feniletilo, además de la síntesis de un nuevo compuesto, el 3-etoxi-1-propanol. Sin embargo, su aportación sobre el color fue nula, así que debería combinarse con una cepa de Saccharomyces cerevisiae con buena formación de pigmentos piranoantociánicos. El empleo de Schizosaccharomyces pombe (938, V1) y Torulaspora delbrueckii (1880) en fermentaciones secuenciales y mixtas con Saccharomyces cerevisiae permitió mejorar el perfil sensorial del vino tinto mediante la mayor síntesis de polioles y la potenciación de aromas frutales, florales y herbáceos, e incrementar la estabilidad de la materia colorante al favorecer la formación de vitisinas y piranoantocianos vinilfenólicos. La crianza sobre lías en barrica a partir de levaduras seleccionadas, puede mejorar la complejidad y persistencia aromática del vino tinto, aunque sin grandes cambios en el color. ABSTRACT The progressive increase in annual average temperature, along with water deficit, is causing significant changes in grape composition and in its maturation, which directly affects the fermentative process and hence alters wine quality. In this work, different strategies for reducing the alcoholic strength, improve wine color and its stability, and increase aromatic complexity and its persistence, are evaluated. By using yeasts with glycolytic inefficiency, it was possible to achieve mean reductions between 0.3 and 1.7 % v/v in the alcoholic strength, while sequential fermentations allowed a maximum reduction of 3.3 and 3.4 % v/v by combining strains 938 (Schizosaccharomyces pombe) and 7013 (Torulaspora delbrueckii) with 7VA (Saccharomyces cerevisiae). When applying a heat shock treatment on the inoculum, only TP2A(16) strain showed a significant mean reduction of 1 % v/v in the alcohol content, compared with the control. The main drawback in all the techniques used to reduce the alcohol content was the lack of repeatability in the results. Moreover, the application of high pressures on destemmed grapes was effective as pasteurization treatment and also as enhancer of polyphenol extraction, achieving an increase of 12.4-18.5% in the average content of total anthocyanins. As expected, addition of flavonoids to the must, stimulated the formation of stable pigments, mainly as a result of condensation reactions between anthocyanins and flavanols mediated by acetaldehyde. With the use of Torulaspora delbrueckii strains in sequential fermentation with Saccharomyces cerevisiae, it was possible to increase the production of diacetyl and 2-phenylethyl acetate, besides the synthesis of a new compound: 3-ethoxy-1-propanol. The use of Schizosaccharomyces pombe (938, V1) and Torulaspora delbrueckii (1880) strains in sequential and mixed fermentations with Saccharomyces cerevisiae improved the sensory profile of red wine by increasing polyols synthesis and enhancing fruity, floral and herbaceous aromas, and it also increased the stability of the coloring matter by favouring vitisins and vinylphenolic pyranoanthocyanins formation. Ageing on lees in barrels from selected yeasts can improve the complexity and aromatic persistence of red wine, without major changes in the color.

One-dimensional linear analysis of the compound jet

The stability of an infinitely long compound liquid column is analysed by using a one-dimensional inviscid slice model. Results obtained from this one-dimensional linear analysis are applicable to the study of compound capillary jets, which are used in the ink-jet printing technique. Stability limits and the breaking regimes of such fluid configurations are established, and, whenever possible, theoretical results are compared with experimental ones.