Analysis and optimization of propagation losses in LiNbO3 optical waveguides produced by swift heavy-ion irradiation

The propagation losses (PL) of lithium niobate optical planar waveguides fabricated by swift heavy-ion irradiation (SHI), an alternative to conventional ion implantation, have been investigated and optimized. For waveguide fabrication, congruently melting LiNbO3 substrates were irradiated with F ions at 20 MeV or 30 MeV and fluences in the range 1013–1014 cm−2. The influence of the temperature and time of post-irradiation annealing treatments has been systematically studied. Optimum propagation losses lower than 0.5 dB/cm have been obtained for both TE and TM modes, after a two-stage annealing treatment at 350 and 375∘C. Possible loss mechanisms are discussed.

Single - and double energy swift and slow heavy ion irradiated optical waveguides in Er: Tungstene-Tellurite glass and BGO for telecom applications

The fabrication of broadband amplifiers in wavelength division multiplexing (WDM) around 1.55 m, as they exhibit large stimulated cross sections and broad emission bandwidth. Bi4Ge3O12 (eultine type BGO) - well known scintillator material, also a rare-earth host material, photorefractive waveguides produced in it only using light ions in the past. Recently: MeV N+ ions and swift O5+ and C5+ ions, too*. Bi12GeO20 (sillenite type BGO) - high photoconductivity and photorefractive sensitivity in the visible and NIR good candidate for real-time holography and optical phase conjugation, photorefractive waveguides produced in it only using light ions. No previous attempts of ion beam fabrication of waveguides in it.

Super-resolution properties of the Spherical Geodesic Waveguides using the perfect drain

Perfect drain for the Maxwell Fish Eye (MFE) is a nonmagnetic dissipative region placed in the focal point to absorb all the incident radiation without reflection or scattering. The perfect drain was recently designed as a material with complex permittivity ? that depends on frequency. However, this material is only a theoretical material, so it can not be used in practical devices. Recently, the perfect drain has been claimed as necessary to achieve super-resolution [Leonhard 2009, New J. Phys. 11 093040], which has increased the interest for practical perfect drains suitable for manufacturing. Here, we analyze the superresolution properties of a device equivalent to the MFE, known as Spherical Geodesic Waveguide (SGW), loaded with the perfect drain. In the SGW the source and drain are implemented with coaxial probes. The perfect drain is realized using a circuit (made of a resistance and a capacitor) connected to the drain coaxial probes. Superresolution analysis for this device is done in Comsol Multiphysics. The results of simulations predict the superresolution up to ? /3000 and optimum power transmission from the source to the drain.

Propagation losses by tunnelling in barrier optical waveguides

An analytical model is proposed in order to estimate the optical propagation losses due to tunnelling in barrier waveguides. The results are validated by means of a beam propagation method (BPM) simulations for different waveguides conditions.

Contribution to the Analysis of Waveguides and Design of Passive Components at Millimeter and Submillimeter-Waves

Esta tesis está dedicada al análisis de las guías de onda y el diseño de los componentes pasivos con énfasis en aplicaciones de alta frecuencia. En primer lugar, se lleva a cabo el análisis de las guías de onda con conductores metálicos no ideales, con el objetivo de establecer el límite superior en frecuencia de las aproximaciones habitualmente utilizadas en microondas para el cálculo de las pérdidas óhmicas. Posteriormente, se presenta el diseño de diferentes componentes pasivos de guía de ondas: filtros, transductores de modos ortogonales (OMT), polarizadores, duplexores y alimentadores de antena, funcionando en frecuencias desde 10 a 750 GHz. Para el correcto diseño de componentes a altas frecuencias se requiere, en primer lugar, comprender los nuevos procesos de fabricación y después adecuar los diversos componentes para cumplir especificaciones eléctricas y geométricas simultáneamente. Para esto, se presentan modificaciones y nuevas geometrías de guiado de ondas para diferentes aplicaciones y procesos tecnológicos. Además se discuten sus ventajas sobre las soluciones ya existentes. Además, el trabajo presentado en esta tesis se ocupa del desarrollo completo de dispositivos: diseño, fabricación y caracterización de los componentes ya mencionados. Por último, algunos de los dispositivos desarrollados han sido diseñados para ser integrados en diferentes sistemas. De esta forma, se mejoran las prestaciones y capacidades de dichos sistemas.

Particle Patterning on Lithium Niobate waveguides via photovoltaic tweezers

Successful micro and nano-particle patterning on iron doped lithium niobate waveguides using photovoltaic fields is reported. This technique previously used in bulk crystals is here applied to waveguide configuration. Well defined particle patterns are obtained using two types of planar waveguides (by proton exchanged and swift heavy ion irradiation) and metallic and dielectric neutral particles. The use of waveguide configuration has allowed a reduction of the light exposure time until 3 s, two orders of magnitude smaller than typical values used in bulk.

Manufacturing arbitrarily-shaped active waveguides with liquid crystal cladding

Many photonic devices are based on waveguides (WG) whose optical properties can be externally modified. These active WGs are usually obtained with electrooptic materials in either the propagating film (core) or the substrate (cladding). In the second case, the WG tunability is based on the interaction of the active material with the evanescent field of the propagating beam.Liquid crystals (LCs) are an excellent choice as electrooptic active materials since they feature high birefringence, low switching voltage, and relatively simple manufacturing. In this work, we have explored alternative ways to prepare WGs of arbitrary shapes avoiding photolithographic steps. To do this, we have employed a UV laser unit (Spectra Physics)attached to an xyzCNC system mounted on an optical bench. The laser power is 300mW, the spot size can be reduced slightly below 1 µm, and the electromechanicalpositioning is well below that number.Different photoresinshave been evaluated for curing time and uniformity; the results have been compared to equivalent WGs realized by standard photolithographic procedures. Best results have been obtained with several kinds of NOA adhesives (Norland Products Inc.) and SU8 (Microchem). NOA81 optical adhesive has been employed by several groups for the preparation ofmicrochannels [1] and microfluidic systems[2]. In our case, several NOAs having different refractive indices have been tested in order to optimize light coupling and guiding. The adhesive is spinnedonto a substrate, and a number of segmented WGs are written with the laser system. The laser power is attenuated 20 dB. Then the laser spot is swept a number of times (from 1 to 900) on every segment. It has been found that, for example, the optimum number of sweeps for NOA81 is 30-70 times (center of the figure) under these conditions. The WG dimensions obtained with this procedure are about 7 µm high and 12 µm wide.

Design of Mm-Wave RLSA with lossy waveguides by slot coupling control techniques

This paper discusses how to design a Radial Line Slot Antenna (RLSA) whose waveguide is filled with high loss dielectric materials. We introduce a new design for the aperture slot coupling synthesis to restrain the dielectric losses and improve the antenna gain. Based on a newly defined slot coupling, a number of RLSAs with different sizes and loss factors are analyzed and their performances are predicted. Theoretical calculations suggest that the gain is sensitive to the material losses in the radial lines. The gain enhancement by using the new coupling formula is notable for larger antenna size and higher loss factor of the dielectric material. Three prototype RLSAs are designed and fabricated at 60GHz following different slot coupling syntheses, and their measured performances consolidate our theory.

UV laser-induced high resolution cleaving of Si wafers for micro-nano devices and polymeric waveguide characterization

In this work we propose a method for cleaving silicon-based photonic chips by using a laser based micromachining system, consisting of a ND:YVO4laser emitting at 355 nm in nanosecond pulse regime and a micropositioning system. The laser makes grooved marks placed at the desired locations and directions where cleaves have to be initiated, and after several processing steps, a crack appears and propagate along the crystallographic planes of the silicon wafer. This allows cleavage of the chips automatically and with high positioning accuracy, and provides polished vertical facets with better quality than the obtained with other cleaving process, which eases the optical characterization of photonic devices. This method has been found to be particularly useful when cleaving small-sized chips, where manual cleaving is hard to perform; and also for polymeric waveguides, whose facets get damaged or even destroyed with polishing or manual cleaving processing. Influence of length of the grooved line and speed of processing is studied for a variety of silicon chips. An application for cleaving and characterizing sol–gel waveguides is presented. The total amount of light coupled is higher than when using any other procedure.

Electromagnetic analysis of periodic structures under a waveguide viewpoint

The fundamental objective of this Ph. D. dissertation is to demonstrate that, under particular circumstances which cover most of the structures with practical interest, periodic structures can be understood and analyzed by means of closed waveguide theories and techniques. To that aim, in the first place a transversely periodic cylindrical structure is considered and the wave equation, under a combination of perfectly conducting and periodic boundary conditions, is studied. This theoretical study runs parallel to the classic analysis of perfectly conducting closed waveguides. Under the light shed by the aforementioned study it is clear that, under certain very common periodicity conditions, transversely periodic cylindrical structures share a lot of properties with closed waveguides. Particularly, they can be characterized by a complete set of TEM, TE and TM modes. As a result, this Ph. D. dissertation introduces the transversely periodic waveguide concept. Once the analogies between the modes of a transversely periodic waveguide and the ones of a closed waveguide have been established, a generalization of a well-known closed waveguide characterization method, the generalized Transverse Resonance Technique, is developed for the obtention of transversely periodic modes. At this point, all the necessary elements for the consideration of discontinuities between two different transversely periodic waveguides are at our disposal. The analysis of this type of discontinuities will be carried out by means of another well known closed waveguide method, the Mode Matching technique. This Ph. D. dissertation contains a sufficient number of examples, including the analysis of a wire-medium slab, a cross-shaped patches periodic surface and a parallel plate waveguide with a textured surface, that demonstrate that the Transverse Resonance Technique - Mode Matching hybrid is highly precise, efficient and versatile. Thus, the initial statement: ”periodic structures can be understood and analyzed by means of closed waveguide theories and techniques”, will be corroborated. Finally, this Ph. D. dissertation contains an adaptation of the aforementioned generalized Transverse Resonance Technique by means of which the analysis of laterally open periodic waveguides, such as the well known Substrate Integrated Waveguides, can be carried out without any approximation. The analysis of this type of structures has suscitated a lot of interest in the recent past and the previous analysis techniques proposed always resorted to some kind of fictitious wall to close the structure. vii Resumen El principal objetivo de esta tesis doctoral es demostrar que, bajo ciertas circunstancias que se cumplen para la gran mayoría de estructuras con interés práctico, las estructuras periódicas se pueden analizar y entender con conceptos y técnicas propias de las guías de onda cerradas. Para ello, en un primer lugar se considera una estructura cilíndrical transversalmente periódica y se estudia la ecuación de onda bajo una combinación de condiciones de contorno periódicas y de conductor perfecto. Este estudio teórico y de caracter general, sigue el análisis clásico de las guías de onda cerradas por conductor eléctrico perfecto. A la luz de los resultados queda claro que, bajo ciertas condiciones de periodicidad (muy comunes en la práctica) las estructuras cilíndricas transversalmente periódicas guardan multitud de analogías con las guías de onda cerradas. En particular, pueden ser descritas mediante un conjunto completo de modos TEM, TE y TM. Por ello, ésta tesis introduce el concepto de guía de onda transversalmente periódica. Una vez establecidas las similitudes entre las soluciones de la ecuación de onda, bajo una combinación de condiciones de contorno periódicas y de conductor perfecto, y los modos de guías de onda cerradas, se lleva a cabo, con éxito, la adaptación de un conocido método de caracterización de guías de onda cerradas, la técnica de la Resonancia Transversal Generalizada, para la obtención de los modos de guías transversalmente periódicas. En este punto, se tienen todos los elementos necesarios para considerar discontinuidades entre guías de onda transversalmente periódicas. El analisis de este tipo de discontinuidades se llevará a cabo mediante otro conocido método de análisis de estructuras cerradas, el Ajuste Modal. Esta tesis muestra multitud de ejemplos, como por ejemplo el análisis de un wire-medium slab, una superficie de parches con forma de cruz o una guía de placas paralelas donde una de dichas placas tiene cierta textura, en los que se demuestra que el método híbrido formado por la Resonancia Transversal Generalizada y el Ajuste Modal, es tremendamente preciso, eficiente y versátil y confirmará la validez de el enunciado inicial: ”las estructuras periódicas se pueden analizar y entender con conceptos y técnicas propias de las guías de onda cerradas” Para terminar, esta tésis doctoral incluye también una modificación de la técnica de la Resonancia Transversal Generalizada mediante la cual es posible abordar el análisis de estructuras periódica abiertas en los laterales, como por ejemplo las famosas guías de onda integradas en sustrato, sin ninguna aproximación. El análisis de este tipo de estructuras ha despertado mucho interés en los últimos años y las técnicas de análisis propuestas hasta ix el momento acostumbran a recurrir a algún tipo de pared ficticia para simular el carácter abierto de la estructura.

Electronic damage in quartz (c-SiO2) by MeV ion irradiations: Potentiality for optical waveguiding applications

The damage induced on quartz (c-SiO2) by heavy ions (F, O, Br) at MeV energies, where electronic stopping is dominant, has been investigated by RBS/C and optical methods. The two techniques indicate the formation of amorphous layers with an isotropic refractive index (n = 1.475) at fluences around 1014 cm−2 that are associated to electronic mechanisms. The kinetics of the process can be described as the superposition of linear (possibly initial Poisson curve) and sigmoidal (Avrami-type) contributions. The coexistence of the two kinetic regimes may be associated to the differential roles of the amorphous track cores and preamorphous halos. By using ions and energies whose maximum stopping power lies inside the crystal (O at 13 MeV, F at 15 MeV and F at 30 MeV) buried amorphous layer are formed and optical waveguides at the sample surface have been generated.

Synthesis of arbitrary group delay responses with all-pass optical cavities structures

We propose a systematic method for the synthesis of arbitrary group delay responses by using allpass structures of coupled optical cavities. Optimum structure parameters design, in terms of filter order and accuracy, are obtained.

Crack mechanical failure in lithium niobate crystal under ion irradiation; novel simulation by extended finite elements

Swift heavy ion irradiation (ions with mass heavier than 15 and energy exceeding MeV/amu) transfer their energy mainly to the electronic system with small momentum transfer per collision. Therefore, they produce linear regions (columnar nano-tracks) around the straight ion trajectory, with marked modifications with respect to the virgin material, e.g., phase transition, amorphization, compaction, changes in physical or chemical properties. In the case of crystalline materials the most distinctive feature of swift heavy ion irradiation is the production of amorphous tracks embedded in the crystal. Lithium niobate is a relevant optical material that presents birefringence due to its anysotropic trigonal structure. The amorphous phase is certainly isotropic. In addition, its refractive index exhibits high contrast with those of the crystalline phase. This allows one to fabricate waveguides by swift ion irradiation with important technological relevance. From the mechanical point of view, the inclusion of an amorphous nano-track (with a density 15% lower than that of the crystal) leads to the generation of important stress/strain fields around the track. Eventually these fields are the origin of crack formation with fatal consequences for the integrity of the samples and the viability of the method for nano-track formation. For certain crystal cuts (X and Y), these fields are clearly anisotropic due to the crystal anisotropy. We have used finite element methods to calculate the stress/strain fields that appear around the ion-generated amorphous nano-tracks for a variety of ion energies and doses. A very remarkable feature for X cut-samples is that the maximum shear stress appears on preferential planes that form +/-45º with respect to the crystallographic planes. This leads to the generation of oriented surface cracks when the dose increases. The growth of the cracks along the anisotropic crystal has been studied by means of novel extended finite element methods, which include cracks as discontinuities. In this way we can study how the length and depth of a crack evolves as function of the ion dose. In this work we will show how the simulations compare with experiments and their application in materials modification by ion irradiation.

Crack mechanical failure in ceramic materials under ion irradiation: case of lithium niobate crystal

Swift heavy ion irradiation (ions with mass heavier than 15 and energy exceeding MeV/amu) transfer their energy mainly to the electronic system with small momentum transfer per collision. Therefore, they produce linear regions (columnar nano-tracks) around the straight ion trajectory, with marked modifications with respect to the virgin material, e.g., phase transition, amorphization, compaction, changes in physical or chemical properties. In the case of crystalline materials the most distinctive feature of swift heavy ion irradiation is the production of amorphous tracks embedded in the crystal. Lithium niobate is a relevant optical material that presents birefringence due to its anysotropic trigonal structure. The amorphous phase is certainly isotropic. In addition, its refractive index exhibits high contrast with those of the crystalline phase. This allows one to fabricate waveguides by swift ion irradiation with important technological relevance. From the mechanical point of view, the inclusion of an amorphous nano-track (with a density 15% lower than that of the crystal) leads to the generation of important stress/strain fields around the track. Eventually these fields are the origin of crack formation with fatal consequences for the integrity of the samples and the viability of the method for nano-track formation. For certain crystal cuts (X and Y), these fields are clearly anisotropic due to the crystal anisotropy. We have used finite element methods to calculate the stress/strain fields that appear around the ion- generated amorphous nano-tracks for a variety of ion energies and doses. A very remarkable feature for X cut-samples is that the maximum shear stress appears on preferential planes that form +/-45º with respect to the crystallographic planes. This leads to the generation of oriented surface cracks when the dose increases. The growth of the cracks along the anisotropic crystal has been studied by means of novel extended finite element methods, which include cracks as discontinuities. In this way we can study how the length and depth of a crack evolves as function of the ion dose. In this work we will show how the simulations compare with experiments and their application in materials modification by ion irradiation.

Tailoring the Optical Properties of Silica Irradiated with Swift Heavy Ions

Irradiation with swift heavy ions (SHI), roughly defined as those having atomic masses larger than 15 and energies exceeding 1 MeV/amu, may lead to significant modification of the irradiated material in a nanometric region around the (straight) ion trajectory (i.e., latent tracks). In the case of amorphous silica it has been reported that SHI irradiation originates nano-tracks of either higher density than the virgin material (for low electronic stopping powers, Se < 7 keV/nm) [1] or having a low-density core and a dense shell (Se > 12 keV/nm) [2]. The intermediate region has not been studied in detail but we will show in this work that essentially no changes in density occur in this zone. An interesting effect of the compaction is that the refractive index is increased with respect to that of the surroundings. In the first Se region it is clear that track overlapping leads to continuous amorphous layers that present a significant contrast with respect to the pristine substrate and this has been used to produce optical waveguides. The optical effects of intermediate and high stopping powers, on the other hand, are largely unknown so far. In this work we have studied theoretically (molecular dynamics and optical simulations) and experimentally (irradiation with SHI and optical characterization) the dependence of the macroscopic optical properties (i.e., the refractive index of the effective medium, n_EMA) on the electronic stopping power of the incoming ions. Our results show that the refractive index of the irradiated silica is not increased in the intermediate region, as expected; however, the core-shell tracks of the high-Se region produce a quite effective enhancement of n_EMA that could prove attractive for the fabrication of optical waveguides at ultralow fluences (as low as 1E11 cm^-2). 1. J. Manzano, J. Olivares, F. Agulló-López, M. L. Crespillo, A. Moroño, and E. Hodgson, "Optical waveguides obtained by swift-ion irradiation on silica (a-SiO2)," Nucl. Instrum. Meth. B 268, 3147-3150 (2010). 2. P. Kluth, C. S. Schnohr, O. H. Pakarinen, F. Djurabekova, D. J. Sprouster, R. Giulian, M. C. Ridgway, A. P. Byrne, C. Trautmann, D. J. Cookson, K. Nordlund, and M. Toulemonde, "Fine structure in swift heavy ion tracks in amorphous SiO2," Phys. Rev. Lett. 101, 175503 (2008).