Impact damage on selected varieties of apples, pears and other fruits.

During the past years, different laboratory impact response studies have been carrj.ec out in following fruits: apples (2 varieties), pears (4 varieties), Asian or Nashi pears (4 varieties), melons (2 varieties), peaches (2 varieties) and avocados. The methodology of the tests is described, as well as the results and observations obtained in each group of tests. Impact response is compared to bruising susceptibility, bruise characteristics (appearance and structural features) and varietal and ripeness differences.

Mechanical segregation of apricot varieties and their ripeness levels at harvest

Some laboratory tests consisting on quasi-static compression and puncture forces carried out on twelve varieties of apricot during 1990 and 1991 were effective in sorting them. These mechanical properties show a high correlation w i th the ethylene production rate per fruit, so allowing to discriminate between ripeness levels at harvest. In this study it is also demonstrated that puncture seems to be the less variable mechanical test. The values (N/mm) obtained with it show a highly significant correlation with compression resistance and with quasi-static compression damage of the fruits.

Surface deformation studies of Tenerife Island, Spain from joint GPS-DInSAR observations

This work presents results for the three-dimensional displacement field at Tenerife Island calculated from campaign GPS and ascending and descending ENVISAT DInSAR interferograms. The goal of this work is to provide an example of the flexibility of the technique by fusing together new varieties of geodetic data, and to observe surface deformations and study precursors of potential activity in volcanic regions. Interferometric processing of ENVISAT data was performed with GAMMA software. All possible combinations were used to create interferograms and then stacking was used to increase signal-to-noise ratio. Decorrelated areas were widely observed, particularly for interferograms with large perpendicular baseline and large time span. Tropospheric signal was also observed which significantly complicated the interpretation. Subsidence signal was observed in the NW part of the island and around Mount Teide and agreed in some regions with campaign GPS data. It is expected that the technique will provide better results when more high quality DInSAR and GPS data is available

Study of Impact and Compression Damage on Asian Pears

Result of impact and compression tests on Chojuro, Twentieth Century, Tsu Li, and Ya Li varieties of Asian pears indicate that Chojuro pears are the firmest and most resistant to mechanical damage. At the time of harvest, Tsu Li and Ya Li pears could resist mechanical damage nearly as well as Chojuro pears, but they become more susceptible to bruising in cold storage. Twentieth Century pears are most sensitive to impact and compression bruising. Increased time in the ripening room produces more softening and increased bruise resistance of Chojuro and Twentieth Century pears than of Tsu Li and Ya Li pears.

Nondestructive quantification of chemical and physical properties of fruits by time-resolved reflectance spectroscopy in the wavelength range 650-1000 nm

Time-resolved reflectance spectroscopy can be used to assess nondestructively the bulk (rather than the superficial) optical properties of highly diffusive media. A fully automated system for time-resolved reflectance spectroscopy was used to evaluate the absorption and the transport scattering spectra of fruits in the red and the near-infrared regions. In particular, data were collected in the range 650-1000 nm from three varieties of apples and from peaches, kiwifruits, and tomatoes. The absorption spectra were usually dominated by the water peak near 970 nm, whereas chlorophyll was detected at 675 nm. For ail species the scattering decreased progressively with increasing wavelength. A best fit to water and chlorophyll absorption line shapes and to Mie theory permitted the estimation of water and chlorophyll content and the average size of scattering centers in the bulls; of intact fruits.

Non-destructive measurements of the optical properties of apples by means of time-resolved reflectance

Time-resolved reflectance is proposed and effectively used for the nondestructive measurement of the optical properties in apples. The technique is based on the detection of the temporal dispersion of a short laser pulse injected into the probed medium. The time-distribution of re-emitted photons interpreted with a solution of the Diffusion equation yields the mean values of the absorption and reduced scattering coefficients of the medium. The proposed technique proved valuable for the measurement of the absorption and scattering spectra of different varieties of apples. No major variations were observed in the experimental data when the fruit was peeled, proving that the measured optical properties are referred to the pulp. The depth of probed volume was determined to be about 2 cm. Finally, the technique proved capable to follow the change in chlorophyll absorption during storage.

Non-destructive measurements of the optical properties of apples by means of time-resolved reflectance

Time-resolved reflectance is proposed and effectively used for the nondestructive measurement of the optical properties in apples. The technique is based on the detection of the temporal dispersion of a short laser pulse injected into the probed medium. The time-distribution of re-emitted photons interpreted with a solution of the Diffusion equation yields the mean values of the absorption and reduced scattering coefficients of the medium. The proposed technique proved valuable for the measurement of the absorption and scattering spectra of different varieties of apples. No major variations were observed in the experimental data when the fruit was peeled, proving that the measured optical properties are referred to the pulp. The depth of probed volume was determined to be about 2 cm. Finally, the technique proved capable to follow the change in chlorophyll absorption during storage.

Sensing physical stage of fruits by their response to non destructive impacts.

Fruits of two varieties of both apples and pears were tested in the laboratory to measure their response to a small energy impact applied by an impact tester. Samples of fruits of increasing maturity were tested during several weeks. Non-destructive impacts and other destructive and non-destructive measurements of post-harvest ripeness were applied. A new software was created to control the impact test, calculate the eleven parameters, and sort out the fruit. This software needs a data base and may create new ones. The implementation of an on-line impact device for automatic detection of texture is being designed (patent pending).

Effect of impacting mass on firmness sensing of fruits.

There has been an increased interest in using impact techniques for sensing firmness of fruits and vegetables. When an impacter is used to impact a fruit, the impacting mass is an important parameter which affects both the impact signal and fruit damage. Results of theoretical analysis and tests conducted on two varieties of pears indicate that lowering the impacting mass results in amplifying the measured signal, reducing sensing errors, and minimizing damage to the fruit.

Effect of impacting radius of curvature on firmness sensing of fruits in a sorting system.

Fruits of two varieties of both apples and pear were tested to measure their response to small energy impact applied by a impact tester with two spherical tips of different radious of curvature ( RA = 2.48 cm and RB = 0.98 cm) and equal mass were used. In the four varieties studied, the size of bruise was smaller with a spherical tip RA than with tip RB . The non-destructive impact test would cause less damage with a spherical impactor with a radious bigger than 0.98 cm.

Non-destructive optical characterisation of fruits with time-resolved reflectance spectroscopy.

Increasing attention is being paid to the possible development of non-invasive tests for the assessment of the quality of fruits We propose a novel non-destructive method for the measurement of the internal optical properties of fruits and vegetables by means of time resolved reflectance spectroscopy in the visible and NIR range. A fully automated instrumentation for time-resolved reflectance measurements was developed It is based on mode-locked laser sources and electronics for time-correlated single photon counting, and provides a time-resolution of 120-160 ps The system was used to probe the optical properties of several species and varieties of fruits and vegetables in the red and NIR range (650-1000 nm). In most fruits, the absorption line shape is dominated by the absorption peak of water, centred around 970 nm Generally, the absorption spectra also show the spectral features typical of chlorophyll, with maximum at 675 nm In particular, for what concerns apples, variations in peak intensity are observed depending on the variety, the degree of ripeness as well as the position on the apple. For all the species and varieties considered, the transport scattering coefficient decreases progressively upon increasing the wavelength.

Non-destructive optical characterization of fruits in the red and near infrared.

Increasing attention is being paid to the possible development of non-invasive tests for the assessment of the quality of Fruits. We propose a novel non-destructive method for the measurement of the internal optical properties of fruits and vegetables by means of lime-resolved reflectance spectroscopy in the visible and NIR range. A Fully automated instrumentation for time-resolved reflectance measurements was developed. It is based on mode-locked laser sources and electronics for time-correlated single photon counting, and provides a time-resolution of 120-160 ps. The system was used to probe the optical properties of several species and varieties of Fruits and vegetables in the red and NIR range (650-1000 nm). In most Fruits, the absorption line shape is dominated by the absorption peak of water, centred around 970 nm. Generally, the absorption spectra also show the spectral features typical of chlorophyll, with maximum at 675 nm. In particular, for what concerns apples, variations in peak intensity are observed depending on the variety, the degree of ripeness as well as the position on the apple. For all the species and varieties considered, the transport scattering coefficient decreases progressively upon increasing the wavelength.

Improving the management of water and nitrogen resources in cropping systems by using simulation models

Los modelos de simulación de cultivos permiten analizar varias combinaciones de laboreo-rotación y explorar escenarios de manejo. El modelo DSSAT fue evaluado bajo condiciones de secano en un experimento de campo de 16 años en la semiárida España central. Se evaluó el efecto del sistema de laboreo y las rotaciones basadas en cereales de invierno, en el rendimiento del cultivo y la calidad del suelo. Los modelos CERES y CROPGRO se utilizaron para simular el crecimiento y rendimiento del cultivo, mientras que el modelo DSSAT CENTURY se utilizó en las simulaciones de SOC y SN. Tanto las observaciones de campo como las simulaciones con CERES-Barley, mostraron que el rendimiento en grano de la cebada era mas bajo para el cereal continuo (BB) que para las rotaciones de veza (VB) y barbecho (FB) en ambos sistemas de laboreo. El modelo predijo más nitrógeno disponible en el laboreo convencional (CT) que en el no laboreo (NT) conduciendo a un mayor rendimiento en el CT. El SOC y el SN en la capa superficial del suelo, fueron mayores en NT que en CT, y disminuyeron con la profundidad en los valores tanto observados como simulados. Las mejores combinaciones para las condiciones de secano estudiadas fueron CT-VB y CT-FB, pero CT presentó menor contenido en SN y SOC que NT. El efecto beneficioso del NT en SOC y SN bajo condiciones Mediterráneas semiáridas puede ser identificado por observaciones de campo y por simulaciones de modelos de cultivos. La simulación del balance de agua en sistemas de cultivo es una herramienta útil para estudiar como el agua puede ser utilizado eficientemente. La comparación del balance de agua de DSSAT , con una simple aproximación “tipping bucket”, con el modelo WAVE más mecanicista, el cual integra la ecuación de Richard , es un potente método para valorar el funcionamiento del modelo. Los parámetros de suelo fueron calibrados usando el método de optimización global Simulated Annealing (SA). Un lisímetro continuo de pesada en suelo desnudo suministró los valores observados de drenaje y evapotranspiración (ET) mientras que el contenido de agua en el suelo (SW) fue suministrado por sensores de capacitancia. Ambos modelos funcionaron bien después de la optimización de los parámetros de suelo con SA, simulando el balance de agua en el suelo para el período de calibración. Para el período de validación, los modelos optimizados predijeron bien el contenido de agua en el suelo y la evaporación del suelo a lo largo del tiempo. Sin embargo, el drenaje fue predicho mejor con WAVE que con DSSAT, el cual presentó mayores errores en los valores acumulados. Esto podría ser debido a la naturaleza mecanicista de WAVE frente a la naturaleza más funcional de DSSAT. Los buenos resultados de WAVE indican que, después de la calibración, este puede ser utilizado como "benchmark" para otros modelos para periodos en los que no haya medidas de campo del drenaje. El funcionamiento de DSSAT-CENTURY en la simulación de SOC y N depende fuertemente del proceso de inicialización. Se propuso como método alternativo (Met.2) la inicialización de las fracciones de SOC a partir de medidas de mineralización aparente del suelo (Napmin). El Met.2 se comparó con el método de inicialización de Basso et al. (2011) (Met.1), aplicando ambos métodos a un experimento de campo de 4 años en un área en regadío de España central. Nmin y Napmin fueron sobreestimados con el Met.1, ya que la fracción estable obtenida (SOC3) en las capas superficiales del suelo fue más baja que con Met.2. El N lixiviado simulado fue similar en los dos métodos, con buenos resultados en los tratamientos de barbecho y cebada. El Met.1 subestimó el SOC en la capa superficial del suelo cuando se comparó con una serie observada de 12 años. El crecimiento y rendimiento del cultivo fueron adecuadamente simulados con ambos métodos, pero el N en la parte aérea de la planta y en el grano fueron sobreestimados con el Met.1. Los resultados variaron significativamente con las fracciones iniciales de SOC, resaltando la importancia del método de inicialización. El Met.2 ofrece una alternativa para la inicialización del modelo CENTURY, mejorando la simulación de procesos de N en el suelo. La continua emergencia de nuevas variedades de híbridos modernos de maíz limita la aplicación de modelos de simulación de cultivos, ya que estos nuevos híbridos necesitan ser calibrados en el campo para ser adecuados para su uso en los modelos. El desarrollo de relaciones basadas en la duración del ciclo, simplificaría los requerimientos de calibración facilitando la rápida incorporación de nuevos cultivares en DSSAT. Seis híbridos de maiz (FAO 300 hasta FAO 700) fueron cultivados en un experimento de campo de dos años en un área semiárida de regadío en España central. Los coeficientes genéticos fueron obtenidos secuencialmente, comenzando con los parámetros de desarrollo fenológico (P1, P2, P5 and PHINT), seguido de los parámetros de crecimiento del cultivo (G2 and G3). Se continuó el procedimiento hasta que la salida de las simulaciones estuvo en concordancia con las observaciones fenológicas de campo. Después de la calibración, los parámetros simulados se ajustaron bien a los parámetros observados, con bajos RMSE en todos los casos. Los P1 y P5 calibrados, incrementaron con la duración del ciclo. P1 fue una función lineal del tiempo térmico (TT) desde emergencia hasta floración y P5 estuvo linealmente relacionada con el TT desde floración a madurez. No hubo diferencias significativas en PHINT entre híbridos de FAO-500 a 700 , ya que tuvieron un número de hojas similar. Como los coeficientes fenológicos estuvieron directamente relacionados con la duración del ciclo, sería posible desarrollar rangos y correlaciones que permitan estimar dichos coeficientes a partir de la clasificación del ciclo. ABSTRACT Crop simulation models allow analyzing various tillage-rotation combinations and exploring management scenarios. DSSAT model was tested under rainfed conditions in a 16-year field experiment in semiarid central Spain. The effect of tillage system and winter cereal-based rotations on the crop yield and soil quality was evaluated. The CERES and CROPGRO models were used to simulate crop growth and yield, while the DSSAT CENTURY was used in the SOC and SN simulations. Both field observations and CERES-Barley simulations, showed that barley grain yield was lower for continuous cereal (BB) than for vetch (VB) and fallow (FB) rotations for both tillage systems. The model predicted higher nitrogen availability in the conventional tillage (CT) than in the no tillage (NT) leading to a higher yield in the CT. The SOC and SN in the top layer, were higher in NT than in CT, and decreased with depth in both simulated and observed values. The best combinations for the dry land conditions studied were CT-VB and CT-FB, but CT presented lower SN and SOC content than NT. The beneficial effect of NT on SOC and SN under semiarid Mediterranean conditions can be identified by field observations and by crop model simulations. The simulation of the water balance in cropping systems is a useful tool to study how water can be used efficiently. The comparison of DSSAT soil water balance, with a simpler “tipping bucket” approach, with the more mechanistic WAVE model, which integrates Richard’s equation, is a powerful method to assess model performance. The soil parameters were calibrated by using the Simulated Annealing (SA) global optimizing method. A continuous weighing lysimeter in a bare fallow provided the observed values of drainage and evapotranspiration (ET) while soil water content (SW) was supplied by capacitance sensors. Both models performed well after optimizing soil parameters with SA, simulating the soil water balance components for the calibrated period. For the validation period, the optimized models predicted well soil water content and soil evaporation over time. However, drainage was predicted better by WAVE than by DSSAT, which presented larger errors in the cumulative values. That could be due to the mechanistic nature of WAVE against the more functional nature of DSSAT. The good results from WAVE indicate that, after calibration, it could be used as benchmark for other models for periods when no drainage field measurements are available. The performance of DSSAT-CENTURY when simulating SOC and N strongly depends on the initialization process. Initialization of the SOC pools from apparent soil N mineralization (Napmin) measurements was proposed as alternative method (Met.2). Method 2 was compared to the Basso et al. (2011) initialization method (Met.1), by applying both methods to a 4-year field experiment in a irrigated area of central Spain. Nmin and Napmin were overestimated by Met.1, since the obtained stable pool (SOC3) in the upper layers was lower than from Met.2. Simulated N leaching was similar for both methods, with good results in fallow and barley treatments. Method 1 underestimated topsoil SOC when compared with a 12-year observed serial. Crop growth and yield were properly simulated by both methods, but N in shoots and grain were overestimated by Met.1. Results varied significantly with the initial SOC pools, highlighting the importance of the initialization procedure. Method 2 offers an alternative to initialize the CENTURY model, enhancing the simulation of soil N processes. The continuous emergence of new varieties of modern maize hybrids limits the application of crop simulation models, since these new hybrids should be calibrated in the field to be suitable for model use. The development of relationships based on the cycle duration, would simplify the calibration requirements facilitating the rapid incorporation of new cultivars into DSSAT. Six maize hybrids (FAO 300 through FAO 700) were grown in a 2-year field experiment in a semiarid irrigated area of central Spain. Genetic coefficients were obtained sequentially, starting with the phenological development parameters (P1, P2, P5 and PHINT), followed by the crop growth parameters (G2 and G3). The procedure was continued until the simulated outputs were in good agreement with the field phenological observations. After calibration, simulated parameters matched observed parameters well, with low RMSE in most cases. The calibrated P1 and P5 increased with the duration of the cycle. P1 was a linear function of the thermal time (TT) from emergence to silking and P5 was linearly related with the TT from silking to maturity . There were no significant differences in PHINT between hybrids from FAO-500 to 700 , as they had similar leaf number. Since phenological coefficients were directly related with the cycle duration, it would be possible to develop ranges and correlations which allow to estimate such coefficients from the cycle classification.

Influence of allelic prolamin variation and localities on durum wheat quality

Thirty-seven varieties of a Mediterranean durum wheat collection grown in Tunisia and Spain were analysed for their allelic composition in prolamins, as well as their protein concentration, sodium dodecyl sulphate sedimentation (SDSS) test and mixograph parameters. Genotype was a greater source of variation in all measurements than locality. Uncommon high and low molecular glutenin subunits (HMW-GS and LMW-GS) were found (V and 2? subunits at Glu-A1, 13 þ 16 at Glu-B1, 5* subunit and ax allele at Glu-A3). The rare combinations 2 þ 4þ14 þ 18 and 8 þ 9þ13 þ 16þ18 subunits at the Glu-B3 locus were found. Glu-A3ax had a positive influence on SDSS and mixograph parameters. Of all the prolamins, those that have the B-LMW-GS composition aaa (for Glu-A3, Glu-B3 and Glu-B2 loci, respectively), when associated with the Glu-A1c and Glu-B1d gave the best semolina quality. By contrast, semolina quality is poor when this same composition is associated with the Glu-A1c and Glu-B1e and even poorer when associated with the Glu-A1c and Glu-B1f. In addition, the cultivars with B-LMW-GS allelic composition aab (for Glu-A3, Glu-B3 and Glu-B2 loci, respectively), when associated with the Glu- A1c and Glu-B1d, gave high quality, whereas when associated with the Glu-A1c and Glu-B1e or with Glu- A1o and Glu-B1f, the quality was very poor.

Podredumbre parda del melocotonero (Monilinia spp.) : detección, identificación de especies y contribución a la epidemiología de la enfermedad

Monilinia spp. (M. laxa, M. fructigena y M. fructicola) causa marchitez en brotes y flores, chancros en ramas y podredumbre de la fruta de hueso provocando pérdidas económicas importantes en años con climatología favorable para el desarrollo de la enfermedad, particularmente en variedades tardías de melocotonero y nectarino. En estos huéspedes en España, hasta el momento, la especie predominante es M. laxa y, en menor proporción, M. fructigena. La reciente introducción en Europa de la especie de cuarentena M. fructicola hace necesaria una detección e identificación rápida de cada una de las especies. Además, hay diversos aspectos de la etiología y epidemiología de la enfermedad que no se conocen en las condiciones de cultivo españolas. En un primer objetivo de esta Tesis se ha abordado la detección e identificación de las especies de Monilinia spp. causantes de podredumbre parda. El estudio de las bases epidemiológicas para el control de la enfermedad constituye el fin del segundo objetivo. Para la detección del género Monilinia en material vegetal por PCR, diferenciándolo de otros hongos presentes en la superficie del melocotonero, se diseñaron una pareja de cebadores siguiendo un análisis del ADN ribosomal. La discriminación entre especies de Monilinia se consiguió utilizando marcadores SCAR (región amplificada de secuencia caracterizada), obtenidos después de un estudio de marcadores polimórficos de ADN amplificados al azar (RAPDs). También fue diseñado un control interno de amplificación (CI) basado en la utilización de un plásmido con secuencias de los cebadores diferenciadores del género, para ser utilizado en el protocolo de diagnóstico de la podredumbre parda con el fin de reconocer falsos negativos debidos a la inhibición de PCR por componentes celulares del material vegetal. Se disponía de un kit comercial que permitía distinguir Monilinia de otros géneros y M. fructicola del resto de especies mediante anticuerpos monoclonales utilizando la técnica DAS-ELISA. En esta Tesis se probaron diferentes fuentes de material como micelio ó conidias procedentes de cultivos en APD, o el micelio de la superficie de frutas o de momias frescas, como formas de antígeno. Los resultados obtenidos con ELISA se compararon con la identificación por métodos morfológico-culturales y por PCR con los cebadores desarrollados en esta Tesis. Los resultados demostraron la posibilidad de una detección temprana en frutas frescas por este método, realzando las posibilidades de una diagnosis temprana para una prevención más eficaz de M. fructicola en fruta de hueso. El estudio epidemiológico de la enfermedad comenzó con la determinación de las principales fuentes de inóculo primario y su importancia relativa en melocotoneros y nectarinos del valle del Ebro. Para ello se muestrearon 9 huertos durante los años 2003 a 2005 recogiendo todas las momias, frutos abortados, gomas, chancros, y brotes necróticos en los árboles. También se recogieron brotes aparentemente sanos y muestras de material vegetal situados en el suelo. En estas muestras se determinó la presencia de Monilinia spp. Los resultados mostraron que la fuente principal de inóculo son las momias que se quedan en los árboles en las que la supervivencia del hongo tras el invierno es muy alta. También son fuentes de inóculo las momias del suelo y los brotes necróticos. De aquí se deriva que una recomendación importante para los agricultores es que deben eliminar este material de los huertos. Un aspecto no estudiado en melocotonero o nectarino en España es la posible relación que puede darse entre la incidencia de infecciones latentes en los frutos inmaduros a lo largo del cultivo y la incidencia de podredumbre en los frutos en el momento de la recolección y en postcosecha. Esta relación se había observado previamente en otros frutales de hueso infectados con M. fructicola en diversos países del mundo. Para estudiar esta relación se realizaron ensayos en cinco huertos comerciales de melocotonero y nectarino situados en el Valle del Ebro en cuatro estados fenológicos durante los años 2000-2002. No se observaron infecciones latentes en botón rosa, dándose la máxima incidencia en precosecha, aunque en algunos huertos se daba otro pico en el endurecimiento del embrión. La especie prevaleciente fue M. laxa. Se obtuvo una correlación positiva significativa entre la incidencia de infecciones latentes y la incidencia de podredumbre en postcosecha. Se desarrolló también un modelo de predicción de las infecciones latentes en función de la temperatura (T) y el periodo de humectación (W). Este modelo indicaba que T y W explicaban el 83% de la variación en la incidencia de infecciones latentes causadas por Monilinia spp. Por debajo de 8ºC no se predecían latentes, necesitándose más de 22h de W para predecir la ocurrencia de latentes con T = 8ºC, mientras que solo se necesitaban 5h de W a 25ºC. Se hicieron también ensayos en condiciones controladas para determinar la relación entre la incidencia de las infecciones latentes, las condiciones ambientales (T y W), la concentración de inóculo del patógeno (I) y el estado de desarrollo del huésped (S) y para validar el modelo de predicción desarrollado con los experimentos de campo. Estos ensayos se llevaron cabo con flores y frutos de nectarino procedentes de un huerto comercial en seis estados fenológicos en los años 2004 y 2005, demostrándose que la incidencia de podredumbre en postcosecha y de infecciones latentes estaba afectada por T, W, I y S. En los frutos se producían infecciones latentes cuando la T no era adecuada para el desarrollo de podredumbre. Una vez desarrollado el embrión eran necesarias más de 4-5h de W al día y un inóculo superior a 104 conidias ml-1 para que se desarrollase o podredumbre o infección latente. La ecuación del modelo obtenido con los datos de campo era capaz de predecir los datos observados en estos experimentos. Para evaluar el efecto del inóculo de Monilinia spp. en la incidencia de infecciones latentes y de podredumbre de frutos en postcosecha se hicieron 11 experimentos en huertos comerciales de melocotonero y nectarino del Valle del Ebro durante 2002 a 2005. Se observó una correlación positiva entre los números de conidias de Monilinia spp. en la superficie de los frutos y la incidencia de infecciones latentes De los estudios anteriores se deducen otras dos recomendaciones importantes para los agricultores: las estrategias de control deben tener en cuenta las infecciones latentes y estimar el riesgo potencial de las mismas basándose en la T y W. Deben tener también en cuenta la concentración de esporas de Monilinia spp. en la superficie de los frutos para disminuir el riesgo de podredumbre parda. El conocimiento de la estructura poblacional de los patógenos sienta las bases para establecer métodos más eficaces de manejo de las enfermedades. Por ello en esta Tesis se ha estudiado el grado de diversidad genética entre distintas poblaciones de M. laxa en diferentes localidades españolas utilizando 144 marcadores RAPDs (59 polimórficos y 85 monomórficos) y 21 aislados. El análisis de la estructura de la población reveló que la diversidad genética dentro de las subpoblaciones (huertos) (HS) representaba el 97% de la diversidad genética (HT), mientras que la diversidad genética entre subpoblaciones (DST) sólo representaba un 3% del total de esta diversidad. La magnitud relativa de la diferenciación génica entre subpoblaciones (GST) alcanzaba 0,032 y el número estimado de migrantes por generación (Nm) fue de 15,1. Los resultados obtenidos en los dendrogramas estaban de acuerdo con el análisis de diversidad génica. Las agrupaciones obtenidas eran independientes del huerto de procedencia, año o huésped. En la Tesis se discute la importancia relativa de las diferentes fuentes evolutivas en las poblaciones de M. laxa. Finalmente se realizó un muestreo en distintos huertos de melocotonero y nectarino del Valle del Ebro para determinar la existencia o no de aislados resistentes a los fungicidas del grupo de los benzimidazoles y las dicarboximidas, fungicidas utilizados habitualmente para el control de la podredumbre parda y con alto riesgo de desarrollar resistencia en las poblaciones patógenas. El análisis de 114 aislados de M. laxa con los fungicidas Benomilo (bencimidazol) (1Bg m.a ml-1), e Iprodiona (dicarboximida) (5Bg m.a ml-1), mostró que ninguno era resistente en las dosis ensayadas. Monilinia spp. (M. laxa, M. fructigena and M. fructicola) cause bud and flower wilt, canker in branches and stone fruit rot giving rise important economic losses in years with appropriate environmental conditions, it is particularly important in late varieties of peach and nectarine. Right now, M. laxa is the major species for peach and nectarine in Spain followed by M. fructigena, in a smaller proportion. The recent introduction of the quarantine organism M. fructicola in Europe makes detection and identification of each one of the species necessary. In addition, there are different aspects of disease etiology and epidemiology that are not well known in Spain conditions. The first goal of this Thesis was the detection and identification of Monilinia spp. causing brown rot. Study of the epidemiology basis for disease control was the second objective. A pair of primers for PCR detection was designed based on the ribosomal DNA sequence in order to detect Monilinia spp. in plant material and to discriminate it from other fungi colonizing peach tree surface. Discrimination among Monilinia spp. was successful by SCAR markers (Sequence Characterized Amplified Region), obtained after a random amplified polymorphic DNA markers (RAPDs) study. An internal control for the PCR (CI) based on the use of a mimic plasmid designed on the primers specific for Monilinia was constructed to be used in diagnosis protocol for brown rot in order to avoid false negatives due to the inhibition of PCR as consequence of remained plant material. A commercial kit based on DAS-ELISA and monoclonals antibodies was successfully tested to distinguish Monilinia from other fungus genera and M. fructicola from other Monilinia species. Different materials such as micelium or conidias from APD cultures, or micelium from fresh fruit surfaces or mummies were tested in this Thesis, as antigens. Results obtained by ELISA were compared to classical identification by morphologic methods and PCR with the primers developed in this Thesis. Results demonstrated the possibility of an early detection in fresh fruits by this method for a more effective prevention of M. fructicola in stone fruit. The epidemiology study of the disease started with the determination of the main sources of primary inoculum and its relative importance in peach trees and nectarines in the Ebro valley. Nine orchards were evaluated during years 2003 to 2005 collecting all mummies, aborted fruits, rubbers, cankers, and necrotic buds from the trees. Apparently healthy buds and plant material located in the ground were also collected. In these samples presence of Monilinia spp. was determined. Results showed that the main inoculum sources are mummies that stay in the trees and where fungus survival after the winter is very high. Mummies on the ground and the necrotics buds are also sources of inoculum. As consequence of this an important recommendation for the growers is the removal of this material of the orchards. An important issue not well studied in peach or nectarine in Spain is the possible relationship between the incidence of latent infections in the immature fruits and the incidence of fruit rot at harvesting and postharvesting. This relationship had been previously shown in other stone fruit trees infected with M. fructicola in different countries over the world. In order to study this relationship experiments were run in five commercial peach and nectarine orchards located in the Ebro Valley in four phenologic states from 2000 to 2002. Latent infections were not observed in pink button, the maxima incidence arise in preharvest, although in some orchards another increase occurred in the embryo hardening. The most prevalence species was M. laxa. A significant positive correlation between the incidence of latent infections and the incidence of rot in postharvest was obtained. A prediction model of the latent infections based on the temperature (T) and the wetness duration (W) was also developed. This model showed that T and W explained 83% of the variation in latent infection incidence caused by Monilinia spp. Below 8ºC latent infection was not predicted, more than 22h of W with T = 8ºC were needed to predict latent infection occurrence of, whereas at 25ºC just 5h of W were enough. Tests under controlled conditions were also made to determine the relationship among latent infections incidence, environmental conditions (T and W), inoculum concentration of the pathogen (I) and development state of the host (S) to validate the prediction model developed on the field experiments. These tests were made with flowers and fruits of nectarine coming from a commercial orchard, in six phenologic states in 2004 and 2005, showing that incidence of rot in postharvest and latent infections were affected by T, W, I and S. In fruits latent infections took place when the T was not suitable for rot development. Once developed the embryo, more than 4-5h of W per day and higher inoculums (104 conidia ml-1) were necessary for rot or latent infection development. The equation of the model obtained with the field data was able to predict the data observed in these experiments. In order to evaluate the effect of inoculum of Monilinia spp. in the incidence of latent infections and of rot of fruits in postharvest, 11 experiments in commercial orchards of peach and nectarine of the Ebro Valley were performed from 2002 to 2005. A positive correlation between the conidial numbers of Monilinia spp. in the surface of the fruits and the incidence of latent infections was observed. Based on those studies other two important recommendations for the agriculturists are deduced: control strategies must consider the latent infections and potential risk based on the T and W. Spores concentration of Monilinia spp. in the surface of fruits must be also taken in concern to reduce the brown rot risk. The knowledge of the population structure of the pathogens determines the bases to establish more effective methods of diseases handling. For that reason in this Thesis the degree of genetic diversity among different M. laxa populations has been studied in different Spanish locations using 144 RAPDs markers (59 polymorphic and 85 monomorphics) on 21 fungal isolates. The analysis of the structure of the population revealed that the genetic diversity within the subpopulations (orchards) (HS) represented 97% of the genetic diversity (HT), whereas the genetic diversity between subpopulations (DST) only represented a 3% of the total of this diversity. The relative magnitude of the genic differentiation between subpopulations (GST) reached 0.032 and the considered number of migrantes by generation (Nm) was of 15.1. The results obtained in dendrograms were in agreement with the analysis of genic diversity. The obtained groupings were independent of the orchard of origin, year or host. In the Thesis the relative importance of the different evolutionary sources in the populations from M. laxa is discussed. Finally a sampling of resistant isolates in different orchards from peach and nectarine of Ebro Valley was made to determine the existence of fungicide resistance of the group of benzimidazoles and the dicarboximidas, fungicides used habitually for the control of rot brown and with high risk of resistance developing in the pathogenic populations. The analysis of 114 isolated ones of M. laxa with the fungicides Benomilo (bencimidazol) (1Bg m.a ml-1), and Iprodiona (dicarboximida) (5Bg m.a ml-1), showed no resistant in the doses evaluated.