Design parameters for continuously variable power-split transmissions using planetaries with 3 active shafts

Since 1996, when the first agricultural tractor with CVT transmission was shown, the presence of this type of transmissions has been increasing. All companies offer them in their products range. Nevertheless, there is little technical documentation that explains the basics of its operation. This report shows all types of CVT transmissions: non-power-split type and power-split ones, as well as the three types used in agricultural tractors, hydro-mechanical power-split transmissions (3 active shafts, input coupled planetary; 3 active shafts, output coupled planetary and 4 active shafts). The report also describes the design parameters of a type of CVT transmission, which use a power-split system with 3 active shafts as well as the fundamental relations among them. Crown Copyright 2010 Published by Elsevier Ltd. on behalf of ISTVS. All rights reserved.

An optimization method for conceptual design in engineering systems based on high order singular value decomposition

Se presenta un nuevo método de diseño conceptual en Ingeniería Aeronáutica basado el uso de modelos reducidos, también llamados modelos sustitutos (‘surrogates’). Los ingredientes de la función objetivo se calculan para cada indiviudo mediante la utilización de modelos sustitutos asociados a las distintas disciplinas técnicas que se construyen mediante definiciones de descomposición en valores singulares de alto orden (HOSVD) e interpolaciones unidimensionales. Estos modelos sustitutos se obtienen a partir de un número limitado de cálculos CFD. Los modelos sustitutos pueden combinarse, bien con un método de optimización global de tipo algoritmo genético, o con un método local de tipo gradiente. El método resultate es flexible a la par que mucho más eficiente, computacionalmente hablando, que los modelos convencionales basados en el cálculo directo de la función objetivo, especialmente si aparecen un gran número de parámetros de diseño y/o de modelado. El método se ilustra considerando una versión simplificada del diseño conceptual de un avión. Abstract An optimization method for conceptual design in Aeronautics is presented that is based on the use of surrogate models. The various ingredients in the target function are calculated for each individual using surrogates of the associated technical disciplines that are constructed via high order singular value decomposition and one dimensional interpolation. These surrogates result from a limited number of CFD calculated snapshots. The surrogates are combined with an optimization method, which can be either a global optimization method such as a genetic algorithm or a local optimization method, such as a gradient-like method. The resulting method is both flexible and much more computationally efficient than the conventional method based on direct calculation of the target function, especially if a large number of free design parameters and/or tunablemodeling parameters are present. The method is illustrated considering a simplified version of the conceptual design of an aircraft empennage.

Integration of design tools and knowledge capture into a CAD system: a case study

onceptual design phase is partially supported by product lifecycle management/computer-aided design (PLM/CAD) systems causing discontinuity of the design information flow: customer needs — functional requirements — key characteristics — design parameters (DPs) — geometric DPs. Aiming to address this issue, it is proposed a knowledge-based approach is proposed to integrate quality function deployment, failure mode and effects analysis, and axiomatic design into a commercial PLM/CAD system. A case study, main subject of this article, was carried out to validate the proposed process, to evaluate, by a pilot development, how the commercial PLM/CAD modules and application programming interface could support the information flow, and based on the pilot scheme results to propose a full development framework.

Design equations for reinforced concrete members strengthened in shear with external FRP reinforcement formulated in an evolutionary multi-objective framework

Methods for predicting the shear capacity of FRP shear strengthened RC beams assume the traditional approach of superimposing the contribution of the FRP reinforcing to the contributions from the reinforcing steel and the concrete. These methods become the basis for most guides for the design of externally bonded FRP systems for strengthening concrete structures. The variations among them come from the way they account for the effect of basic shear design parameters on shear capacity. This paper presents a simple method for defining improved equations to calculate the shear capacity of reinforced concrete beams externally shear strengthened with FRP. For the first time, the equations are obtained in a multiobjective optimization framework solved by using genetic algorithms, resulting from considering simultaneously the experimental results of beams with and without FRP external reinforcement. The performance of the new proposed equations is compared to the predictions with some of the current shear design guidelines for strengthening concrete structures using FRPs. The proposed procedure is also reformulated as a constrained optimization problem to provide more conservative shear predictions.

Preliminary design of symmetric arch-gravity dams

In this paper, a set of design parameters, such as the slopes of upstream and downstream faces of the dam, radius of the upper arch, width of the dam at the top level and height of the vertical upper part of the dam, are given as function of the valley characteristics when the dam is situated, such as its geometry and its geotechnical properties. These tables have been obtained using a regression of the design parameters of an arch-gravity dam with a minimum concrete volume, placed in a large number of valleys with different characteristics and properties. Elasticites for these design parameters are also discussed.

Diseño de un modelo para la identificación y análisis de tramos de carreteras sin accidentes : una nueva visión de la seguridad vial

El planteamiento tradicional de análisis de la accidentalidad en carretera pasa por la consideración de herramientas paliativas, como son la identificación y gestión de los puntos negros o tramos de concentración de accidentes, o preventivas, como las auditorías e inspecciones de seguridad vial. En esta tesis doctoral se presenta un planteamiento complementario a estas herramientas, desde una perspectiva novedosa: la consideración de los tramos donde no se producen accidentes; son los denominados Tramos Blancos. La tesis persigue demostrar que existen determinados parámetros del diseño de las carreteras y del tráfico que, bajo características generales similares de las vías, tienen influencia en el hecho de que se produzcan o no accidentes, adicionalmente a la exposición al riesgo, como factor principal, y a otros factores. La propia definición de los Tramos Blancos, entendidos como tramos de carreteras de longitud representativa donde no se han producido accidentes con víctimas mortales o heridos graves durante un periodo largo de tiempo, garantiza que esta situación no se produzca como consecuencia de la aleatoriedad de los accidentes, sino que pudiera deberse a una confluencia específica de determinados parámetros de la geometría de la vía y del tráfico total y de vehículos pesados. Para el desarrollo de esta investigación se han considerado la red de autopistas de peaje y las carreteras convencionales de la Red del Estado de España, que supone un total de 17.000 kilómetros, y los datos de accidentes con víctimas mortales y heridos graves en el periodo 2006-2010, ambos incluidos, en estas redes (un total de 10.000 accidentes). La red viaria objeto de análisis supone el 65% de la longitud de la Red de Carreteras del Estado, por la que circula el 33% de su tráfico; en ella se produjeron en el año 2013 el 47% de los accidentes con víctimas y el 60% de las víctimas mortales de la Red de Carreteras del Estado. Durante la investigación se ha desarrollado una base de datos de 250.130 registros y más de 3.5 millones de datos en el caso de las autopistas de peaje de la Red de Carreteras del Estado y de 935.402 registros y más de 14 millones de datos en el caso de la red convencional del Estado analizada. Tanto las autopistas de peaje como las carreteras convencionales han sido clasificadas según sus características de tráfico, de manera que se valoren vías con nivel de exposición al riesgo similar. Para cada tipología de vía, se ha definido como longitud de referencia para que un tramo se considere Tramo Blanco la longitud igual al percentil 95 de las longitudes de tramos sin accidentes con heridos graves o víctimas mortales durante el periodo 2006-2010. En el caso de las autopistas de peaje, en la tipología que ha sido considerada para la definición del modelo, esta longitud de referencia se estableció en 14.5 kilómetros, mientras que en el caso de las carreteras convencionales, se estableció en 7.75 kilómetros. Para cada uno de los tipos de vía considerados se han construido una base de datos en la que se han incluido las variables de existencia o no de Tramo Blanco, así como las variables de tráfico (intensidad media diaria total, intensidad de vehículos pesados y porcentaje de vehículos pesados ), la velocidad media y las variables de geometría (número de carriles, ancho de carril, ancho de arcén derecho e izquierdo, ancho de calzada y plataforma, radio, peralte, pendiente y visibilidad directa e inversa en los casos disponibles); como variables adicionales, se han incluido el número de accidentes con víctimas, los fallecidos y heridos graves, índices de peligrosidad, índices de mortalidad y exposición al riesgo. Los trabajos desarrollados para explicar la presencia de Tramos Blancos en la red de autopistas de peaje han permitido establecer las diferencias entre los valores medios de las variables de tráfico y diseño geométrico en Tramos Blancos respecto a tramos no blancos y comprobar que estas diferencias son significativas. Así mismo, se ha podido calibrar un modelo de regresión logística que explica parcialmente la existencia de Tramos Blancos, para rangos de tráfico inferiores a 10.000 vehículos diarios y para tráficos entre 10.000 y 15.000 vehículos diarios. Para el primer grupo (menos de 10.000 vehículos al día), las variables que han demostrado tener una mayor influencia en la existencia de Tramo Blanco son la velocidad media de circulación, el ancho de carril, el ancho de arcén izquierdo y el porcentaje de vehículos pesados. Para el segundo grupo (entre 10.000 y 15.000 vehículos al día), las variables independientes más influyentes en la existencia de Tramo Blanco han sido la velocidad de circulación, el ancho de calzada y el porcentaje de vehículos pesados. En el caso de las carreteras convencionales, los diferentes análisis realizados no han permitido identificar un modelo que consiga una buena clasificación de los Tramos Blancos. Aun así, se puede afirmar que los valores medios de las variables de intensidad de tráfico, radio, visibilidad, peralte y pendiente presentan diferencias significativas en los Tramos Blancos respecto a los no blancos, que varían en función de la intensidad de tráfico. Los resultados obtenidos deben considerarse como la conclusión de un análisis preliminar, dado que existen otros parámetros, tanto de diseño de la vía como de la circulación, el entorno, el factor humano o el vehículo que podrían tener una influencia en el hecho que se analiza, y no se han considerado por no disponer de esta información. En esta misma línea, el análisis de las circunstancias que rodean al viaje que el usuario de la vía realiza, su tipología y motivación es una fuente de información de interés de la que no se tienen datos y que permitiría mejorar el análisis de accidentalidad en general, y en particular el de esta investigación. Adicionalmente, se reconocen limitaciones en el desarrollo de esta investigación, en las que sería preciso profundizar en el futuro, reconociendo así nuevas líneas de investigación de interés. The traditional approach to road accidents analysis has been based in the use of palliative tools, such as black spot (or road sections) identification and management, or preventive tools, such as road safety audits and inspections. This thesis shows a complementary approach to the existing tools, from a new perspective: the consideration of road sections where no accidents have occurred; these are the so-called White Road Sections. The aim of this thesis is to show that there are certain design parameters and traffic characteristics which, under similar circumstances for roads, have influence in the fact that accidents occur, in addition to the main factor, which is the risk exposure, and others. White Road Sections, defined as road sections of a representative length, where no fatal accidents or accidents involving serious injured have happened during a long period of time, should not be a product of randomness of accidents; on the contrary, they might be the consequence of a confluence of specific parameters of road geometry, traffic volumes and heavy vehicles traffic volumes. For this research, the toll motorway network and single-carriageway network of the Spanish National Road Network have been considered, which is a total of 17.000 kilometers; fatal accidents and those involving serious injured from the period 2006-2010 have been considered (a total number of 10.000 accidents). The road network covered means 65% of the total length of the National Road Network, which allocates 33% of traffic volume; 47% of accidents with victims and 60% of fatalities happened in these road networks during 2013. During the research, a database of 250.130 registers and more than 3.5 million data for toll motorways and 935.042 registers and more than 14 million data for single carriageways of the National Road Network was developed. Both toll motorways and single-carriageways have been classified according to their traffic characteristics, so that the analysis is performed over roads with similar risk exposure. For each road type, a reference length for White Road Section has been defined, as the 95 percentile of all road sections lengths without accidents (with fatalities or serious injured) for 2006-2010. For toll motorways, this reference length concluded to be 14.5 kilometers, while for single-carriageways, it was defined as 7.75 kilometers. A detailed database was developed for each type of road, including the variable “existence of White Road Section”, as well as variables of traffic (average daily traffic volume, heavy vehicles average daily traffic and percentage of heavy vehicles from the total traffic volume), average speed and geometry variables (number of lanes, width of lane, width of shoulders, carriageway width, platform width, radius, superelevation, slope and visibility); additional variables, such as number of accidents with victims, number of fatalities or serious injured, risk and fatality rates and risk exposure, have also been included. Research conducted for the explanation of the presence of White Road Sections in the toll motorway network have shown statistically significant differences in the average values of variables of traffic and geometric design in White Road Sections compared with other road sections. In addition, a binary logistic model for the partial explanation of the presence of White Road Sections was developed, for traffic volumes lower than 10.000 daily vehicles and for those running from 10.000 to 15.000 daily vehicles. For the first group, the most influent variables for the presence of White Road Sections were the average speed, width of lane, width of left shoulder and percentage of heavy vehicles. For the second group, the most influent variables were found to be average speed, carriageway width and percentage of heavy vehicles. For single-carriageways, the different analysis developed did not reach a proper model for the explanation of White Road Sections. However, it can be assumed that the average values of the variables of traffic volume, radius, visibility, superelevation and slope show significant differences in White Road Sections if compared with others, which also vary with traffic volumes. Results obtained should be considered as a conclusion of a preliminary analysis, as there are other parameters, not only design-related, but also regarding traffic, environment, human factor and vehicle which could have an influence in the fact under research, but this information has not been considered in the analysis, as it was not available. In parallel, the analysis of the circumstances around the trip, including its typology and motivation is an interesting source of information, from which data are not available; the availability of this information would be useful for the improvement of accident analysis, in general, and for this research work, in particular. In addition, there are some limitations in the development of the research work; it would be necessary to develop an in-depth analysis in the future, thus assuming new research lines of interest.

Design Parameter Analysis of Point Absorber WEC via an Evolutionary-Algorithm-Based Dimensioning Tool

Wave energy conversion has an essential difference from other renewable energies since the dependence between the devices design and the energy resource is stronger. Dimensioning is therefore considered a key stage when a design project of Wave Energy Converters (WEC) is undertaken. Location, WEC concept, Power Take-Off (PTO) type, control strategy and hydrodynamic resonance considerations are some of the critical aspects to take into account to achieve a good performance. The paper proposes an automatic dimensioning methodology to be accomplished at the initial design project stages and the following elements are described to carry out the study: an optimization design algorithm, its objective functions and restrictions, a PTO model, as well as a procedure to evaluate the WEC energy production. After that, a parametric analysis is included considering different combinations of the key parameters previously introduced. A variety of study cases are analysed from the point of view of energy production for different design-parameters and all of them are compared with a reference case. Finally, a discussion is presented based on the results obtained, and some recommendations to face the WEC design stage are given.

Influence of Current Pulse Shape on Directly Modulated Systems Performance in Metro Area Optical Networks

Due to the fact that a metro network market is very cost sensitive, direct modulated schemes appear attractive. In this paper a CWDM (Coarse Wavelength Division Multiplexing) system is studied in detail by means of an Optical Communication System Design Software; a detailed study of the modulated current shape (exponential, sine and gaussian) for 2.5 Gb/s CWDM Metropolitan Area Networks is performed to evaluate its tolerance to linear impairments such as signal-to-noise-ratio degradation and dispersion. Point-to-point links are investigated and optimum design parameters are obtained. Through extensive sets of simulation results, it is shown that some of these shape pulses are more tolerant to dispersion when compared with conventional gaussian shape pulses. In order to achieve a low Bit Error Rate (BER), different types of optical transmitters are considered including strongly adiabatic and transient chirp dominated Directly Modulated Lasers (DMLs). We have used fibers with different dispersion characteristics, showing that the system performance depends, strongly, on the chosen DML?fiber couple.

Dynamic response of hydro power plants for providing secondary regulation reserves considering elastic water column effects

In this paper, the dynamic response of a hydro power plant for providing secondary regulation reserve is studied in detail. Special emphasis is given to the elastic water column effects both in the penstock and the tailrace tunnel. For this purpose, a nonlinear model based on the analogy between mass and momentum conservation equations of a water conduit and those of wave propagation in transmission lines is used. The influence of the plant configuration and design parameters on the fulfilment of the Spanish Electrical System Operator requirements is analysed

Environmental analysis of residential building facades through energy consumption, GHG emissions and costs

This paper provides some results on the potential to minimize environmental impacts in residential buildings life cycle, through façade design strategies, analyzing also their impact on costs from a lifecycle perspective. On one hand, it assesses the environmental damage produced by the materials of the building envelope, and on the other, the benefits they offer in terms of habitability and liveability in the use phase. The analysis includes several design parameters used both for rehabilitation of existing facades, as for new facades, trying to cover various determinants and proposing project alternatives. With this study we intended to contribute to address the energy challenges for the coming years, trying also to propose pathways for innovative solutions for the building envelope.

Aspectos de la medición dinámica instantánea de emisiones de motores. Aplicación al desarrollo de un equipo portátil y una metodología para estudios de contaminación de vehículos en tráfico real.

Esta Tesis Doctoral se encuadra en el ámbito de la medida de emisiones contaminantes y de consumo de combustible en motores de combustión interna alternativos cuando se utilizan como plantas de potencia para propulsión de vehículos ligeros de carretera, y más concretamente en las medidas dinámicas con el vehículo circulando en tráfico real. En este ámbito, el objetivo principal de la Tesis es estudiar los problemas asociados a la medición en tiempo real con equipos embarcados de variables medioambientales, energéticas y de actividad, de vehículos ligeros propulsados por motores térmicos en tráfico real. Y como consecuencia, desarrollar un equipo y una metodología apropiada para este objetivo, con el fin de realizar consiguientemente un estudio sobre los diferentes factores que influyen sobre las emisiones y el consumo de combustible de vehículos turismo en tráfico real. La Tesis se comienza realizando un estudio prospectivo sobre los trabajos de otros autores relativos al desarrollo de equipos portátiles de medida de emisiones (Portable Emission Measurement Systems – PEMS), problemas asociados a la medición dinámica de emisiones y estudios de aplicación en tráfico real utilizando este tipo de equipos. Como resultado de este estudio se plantea la necesidad de disponer de un equipo específicamente diseñado para ser embarcado en un vehículo que sea capaz de medir en tiempo real las concentraciones de emisiones y el caudal de gases de escape, al mismo tiempo que se registran variables del motor, del vehículo y del entorno como son la pendiente y los datos meteorológicos. De esta forma se establecen las especificaciones y condiciones de diseño del equipo PEMS. Aunque al inicio de esta Tesis ya existían en el mercado algunos sistemas portátiles de medida de emisiones (PEMS: Portable Emissions Measurement Systems), en esta Tesis se investiga, diseña y construye un nuevo sistema propio, denominado MIVECO – PEMS. Se exponen, discuten y justifican todas las soluciones técnicas incorporadas en el sistema que incluyen los subsistema de análisis de gases, subsistemas de toma de muestra incluyendo caudalímetro de gases de escape, el subsistema de medida de variables del entorno y actividad del vehículo y el conjunto de sistemas auxiliares. El diseño final responde a las hipótesis y necesidades planteadas y se valida en uso real, en banco de rodillos y en comparación con otro equipos de medida de emisiones estacionarios y portátiles. En esta Tesis se presenta también toda la investigación que ha conducido a establecer la metodología de tratamiento de las señales registradas en tiempo real que incluye la sincronización, cálculos y propagación de errores. La metodología de selección y caracterización de los recorridos y circuitos y de las pautas de conducción, preparación del vehículo y calibración de los equipos forma también parte del legado de esta Tesis. Para demostrar la capacidad de medida del equipo y el tipo de resultados que pueden obtenerse y que son útiles para la comunidad científica, y las autoridades medioambientales en la parte final de esta Tesis se plantean y se presentan los resultados de varios estudios de variables endógenas y exógenas que afectan a las emisiones instantáneas y a los factores de emisión y consumo (g/km) como: el estilo de conducción, la infraestructura vial, el nivel de congestión del tráfico, tráfico urbano o extraurbano, el contenido de biocarburante, tipo de motor (diesel y encendido provocado), etc. Las principales conclusiones de esta Tesis son que es posible medir emisiones másicas y consumo de motores de vehículos en uso real y que los resultados permiten establecer políticas de reducción de impacto medio ambiental y de eficiencia energética, pero, se deben establecer unas metodologías precisas y se debe tener mucho cuidado en todo el proceso de calibración, medida y postratamientos de los datos. Abstract This doctoral thesis is in the field of emissions and fuel consumption measurement of reciprocating internal combustion engines when are used as power-trains for light-duty road vehicles, and especially in the real-time dynamic measurements procedures when the vehicle is being driven in real traffic. In this context, the main objective of this thesis is to study the problems associated with on-board real-time measuring systems of environmental, energy and activity variables of light vehicles powered by internal combustion engines in real traffic, and as a result, to develop an instrument and an appropriate methodology for this purpose, and consequently to make a study of the different factors which influence the emissions and the fuel consumption of passenger cars in real traffic. The thesis begins developing a prospective study on other authors’ works about development of Portable Emission Measurement Systems (PEMS), problems associated with dynamic emission measurements and application studies on actual traffic using PEMS. As a result of this study, it was shown that a measuring system specifically designed for being on-board on a vehicle, which can measure in real time emission concentrations and exhaust flow, and at the same time to record motor vehicle and environment variables as the slope and atmospheric data, is needed; and the specifications and design parameters of the equipment are proposed. Although at the beginning of this research work there were already on the market some PEMS, in this Thesis a new system is researched, designed and built, called MIVECO – PEMS, in order to meet such measurements needs. Following that, there are presented, discussed and justify all technical solutions incorporated in the system, including the gas analysis subsystem, sampling and exhaust gas flowmeter subsystem, the subsystem for measurement of environment variables and of the vehicle activity and the set of auxiliary subsystems. The final design meets the needs and hypotheses proposed, and is validated in real-life use and chassis dynamometer testing and is also compared with other stationary and on-board systems. This thesis also presents all the research that has led to the methodology of processing the set of signals recorded in real time including signal timing, calculations and error propagation. The methodology to select and characterize of the routes and circuits, the driving patterns, and the vehicle preparation and calibration of the instruments and sensors are part of the legacy of this thesis. To demonstrate the measurement capabilities of the system and the type of results that can be obtained and that are useful for the scientific community and the environmental authorities, at the end of this Thesis is presented the results of several studies of endogenous and exogenous variables that affect the instantaneous and averaged emissions and consumption factors (g/km), as: driving style, road infrastructure, the level of traffic congestion, urban and extra-urban traffic, biofuels content, type of engine (diesel or spark ignition) etc. The main conclusions of this thesis are that it is possible to measure mass emissions and consumption of vehicle engines in actual use and that the results allow us to establish policies to reduce environmental impact and improve energy efficiency, but, to establish precise methodologies and to be very careful in the entire process of calibration, measurement and data post-treatment is necessary.

Optimización de la producción de la fase de avance en el túnel de Seiró (Ourense)

Este proyecto desarrolla una metodología de toma de datos y análisis para la optimización de la producción de la fase de avance de construcción del túnel de Seiró. Este túnel forma parte de las obras de construcción de la línea ferroviaria de alta velocidad corredor norte-noroeste a su paso por la provincia de Ourense. Mediante el análisis de diversos parámetros del diseño de la voladura, en la construcción de un túnel de 73 m2 de sección, en roca granítica, se pretende optimizar el tiempo de ciclo de excavación. Se estudia la variación de la fragmentación, el contorno y el avance obtenido y la influencia sobre estos parámetros del esquema de tiro y el tipo de cuele empleados y sus repercusiones en el tiempo de ciclo. El resultado del análisis concluye que el esquema de tiro óptimo, entre los usados, está formado por 112 barrenos de 51 mm de diámetro, con un cuele de 4 barrenos vacíos, que da lugar a mejores resultados de avance, contorno y fragmentación sin afectar negativamente al tiempo de ciclo. ABSTRACT This project develops a methodology for excavation cycle optimization by collecting and analyzing operational data for Seiró Tunnel construction site. This tunnel is included in construction project of high speed railway, located in N-NW direction, in Ourense province. Analyzing several blasting design parameters from the construction of a 73 m2 tunnel, in granitic rock, allows the optimization of cycle time. Variations in fragmentation, contour and advance length and influence about those parameters from blasting design und cut type used and its impact in the cycle time. Analysis results show up the best blasting design, among used, is formed of 112 holes 51 mm diameter, and a parallel cut with 4 empty holes. This configuration achieves the best fragmentation, contour and advance length without negative effects in time cycle

Dynamic response of hydro power plants to load variations for providing secondary regulation reserves considering elastic water column effects

In this paper, the dynamic response of a hydro power plant for providing secondary regulation reserve is studied in detail. S pecial emphasis is given to the elastic water column effects both in the penstock and the tailrace tunnel. For this purpose, a nonline ar model based on the analogy between mass and momentum conservation equations of a water conduit and those of wave propagation in transmission lines is used. The influence of the plant configuration and design parameters on the fulfilment of the Spanish Electrical System Operator requirem ents is analysed.

Aerodynamic optimization of the ICE2 high-speed train nose using a genetic algorithm and metamodels

An aerodynamic optimization of the ICE 2 high-speed train nose in term of front wind action sensitivity is carried out in this paper. The nose is parametrically defined by Be?zier Curves, and a three-dimensional representation of the nose is obtained using thirty one design variables. This implies a more complete parametrization, allowing the representation of a real model. In order to perform this study a genetic algorithm (GA) is used. Using a GA involves a large number of evaluations before finding such optimal. Hence it is proposed the use of metamodels or surrogate models to replace Navier-Stokes solver and speed up the optimization process. Adaptive sampling is considered to optimize surrogate model fitting and minimize computational cost when dealing with a very large number of design parameters. The paper introduces the feasi- bility of using GA in combination with metamodels for real high-speed train geometry optimization.

Efficient management of available technologies. Aplication to mining operations for industry supplies

Nowadays, processing Industry Sector is going through a series of changes, including right management and reduction of environmental affections. Any productive process which looks for sustainable management is incomplete if Cycle of Life of mineral resources sustainability is not taken into account. Raw materials for manufacturing are provided by mineral resources extraction processes, such as copper, aluminum, iron, gold, silver, silicon, titanium? Those elements are necessary for Mankind development and are obtained from the Earth through mineral extractive processes. Mineral extraction processes are operations which must take care about the environmental consequences. Extraction of huge volumes of rock for their transformation into raw materials for industry must be optimized to reduce ecological cost of the final product as l was possible. Reducing the ecological balance on a global scale has no sense to design an efficient manufacturing in secondary industry (transformation), if in first steps of the supply chain (extraction) impact exceeds the savings of resources in successive phases. Mining operations size suggests that it is an environmental aggressive activity, but precisely because of its great impact must be the first element to be considered. That idea implies that a new concept born: Reduce economical and environmental cost This work aims to make a reflection on the parameters that can be modified to reduce the energy cost of the process without an increasing in operational costs and always ensuring the same production capacity. That means minimize economic and environmental cost at same time. An efficient design of mining operation which has taken into account that idea does not implies an increasing of the operating cost. To get this objective is necessary to think in global operation view to make that all departments involved have common guidelines which make you think in the optimization of global energy costs. Sometimes a single operational cost must be increased to reduce global cost. This work makes a review through different design parameters of surface mining setting some key performance indicators (KPIs) which are estimated from an efficient point of view. Those KPIs can be included by HQE Policies as global indicators. The new concept developed is that a new criteria has to be applied in company policies: improve management, improving OPERATIONAL efficiency. That means, that is better to use current resources properly (machinery, equipment,?) than to replace them with new things but not used correctly. As a conclusion, through an efficient management of current technologies in each extractive operation an important reduction of the energy can be achieved looking at downstream in the process. That implies a lower energetic cost in the whole cycle of life in manufactured product.