Effect of field damping layer on two step absorption of quantum dots solar cells

Multi-stacked InAs/AlGaAs quantum dot solar cells (QDSCs) introduced with field damping layers (FDL) which sustain the junction built-in potential have been studied. Without an external bias condition, the external quantum efficiency (EQE) of QD layers are reduced by introducing the thick FDL, because the carrier escape due to built-in electric field was suppressed. On the other hand, the photocurrent production due to two-step absorption is increased by the formation of flat-band QD structure for QDSC with thick FDL.

Study of rapid ionisation for simulation of soft X-ray lasers with the 2D hydro-radiative code ARWEN

We present our fast ionisation routine used to study transient softX-raylasers with ARWEN, a two-dimensional hydrodynamic code incorporating adaptative mesh refinement (AMR) and radiative transport. We compute global rates between ion stages assuming an effective temperature between singly-excited levels of each ion. A two-step method is used to obtain in a straightforward manner the variation of ion populations over long hydrodynamic time steps. We compare our model with existing theoretical results both stationary and transient, finding that the discrepancies are moderate except for large densities. We simulate an existing Molybdenum Ni-like transient softX-raylaser with ARWEN. Use of the fast ionisation routine leads to a larger increase in temperature and a larger gain zone than when LTE datatables are used.

Automatic motion compensation of free breathing acquired myocardial perfusion data by using independent component analysis

Images acquired during free breathing using first-pass gadolinium-enhanced myocardial perfusion magnetic resonance imaging (MRI) exhibit a quasiperiodic motion pattern that needs to be compensated for if a further automatic analysis of the perfusion is to be executed. In this work, we present a method to compensate this movement by combining independent component analysis (ICA) and image registration: First, we use ICA and a time?frequency analysis to identify the motion and separate it from the intensity change induced by the contrast agent. Then, synthetic reference images are created by recombining all the independent components but the one related to the motion. Therefore, the resulting image series does not exhibit motion and its images have intensities similar to those of their original counterparts. Motion compensation is then achieved by using a multi-pass image registration procedure. We tested our method on 39 image series acquired from 13 patients, covering the basal, mid and apical areas of the left heart ventricle and consisting of 58 perfusion images each. We validated our method by comparing manually tracked intensity profiles of the myocardial sections to automatically generated ones before and after registration of 13 patient data sets (39 distinct slices). We compared linear, non-linear, and combined ICA based registration approaches and previously published motion compensation schemes. Considering run-time and accuracy, a two-step ICA based motion compensation scheme that first optimizes a translation and then for non-linear transformation performed best and achieves registration of the whole series in 32 ± 12 s on a recent workstation. The proposed scheme improves the Pearsons correlation coefficient between manually and automatically obtained time?intensity curves from .84 ± .19 before registration to .96 ± .06 after registration

Correlation between ileal digestibility of amino acids and chemical composition of soybean meals in broilers at 21 days of age

The correlations between chemical composition and coefficient of standardized ileal digestibility (CSID) of crude protein (CP) and amino acids (AA) were determined in 22 soybean meal (SBM) samples originated from USA (n = 8), Brazil (BRA; n = 7) and Argentina (ARG; n = 7) in 21-day old broilers. Birds were fed a commercial maize-SBM diet from 1 to 17 days of age followed by the experimental diets in which the SBM tested was the only source of protein (205 g CP/kg) for three days. Also, in vitro nitrogen (N) digestion study was conducted with these samples using the two-step enzymatic method. The coefficient of apparent ileal digestibility (CAID) of the SBM, independent of the origin, varied from 0.820 to 0.880 for CP, 0.850 to 0.905 for lysine (Lys), 0.859 to 0.907 for methionine (Met) and 0.664 to 0.750 for cysteine (Cys). The corresponding CSID values varied from 0.850 to 0.966 for CP, 0.891 to 0.940 for Lys, 0.931 to 0.970 for Met and 0.786 to 0.855 for Cys. The CSID of CP and Lys of the SBM were positively correlated with CP (r = 0.514; P menor que 0.05 and r = 0.370; P = 0.09, respectively), KOH solubility (KOH sol.) (r = 0.696; P menor que 0.001 and r = 0.619; P menor que 0.01, respectively), trypsin inhibitor activity (TIA) (r = 0.541; P menor que 0.01 and r = 0.416; P = 0.05, respectively) and reactive Lys (r = 0.563; P menor que 0.01 and r = 0.486; P menor que 0.05) values, but no relation was observed with neutral detergent fiber and oligosaccharide content. No relation between the CSID of CP determined in vivo and N digestibility determined in vitro was found. The CSID of most key AA were higher for the USA and the BRA meals than for the ARG meals. For Lys, the CSID was 0.921, 0.919 and 0.908 (P menor que 0.05) and for Cys 0.828, 0.833 and 0.800 (P menor que 0.01) for USA, BRA and ARG meals, respectively. It is concluded that under the conditions of this experiment, the CSID of CP and Lys increased with CP content, KOH sol., TIA and reactive Lys values of the SBM. The CSID of most limiting AA, including Lys and Cys, were higher for USA and BRA meals than for ARG meals.

Hybrid incremental modeling based on least squares and fuzzy K-NN for monitoring tool wear in turning processes

There is now an emerging need for an efficient modeling strategy to develop a new generation of monitoring systems. One method of approaching the modeling of complex processes is to obtain a global model. It should be able to capture the basic or general behavior of the system, by means of a linear or quadratic regression, and then superimpose a local model on it that can capture the localized nonlinearities of the system. In this paper, a novel method based on a hybrid incremental modeling approach is designed and applied for tool wear detection in turning processes. It involves a two-step iterative process that combines a global model with a local model to take advantage of their underlying, complementary capacities. Thus, the first step constructs a global model using a least squares regression. A local model using the fuzzy k-nearest-neighbors smoothing algorithm is obtained in the second step. A comparative study then demonstrates that the hybrid incremental model provides better error-based performance indices for detecting tool wear than a transductive neurofuzzy model and an inductive neurofuzzy model.

Aerial video geo-registration using terrain models from dense and coherent stereo matching

In the context of aerial imagery, one of the first steps toward a coherent processing of the information contained in multiple images is geo-registration, which consists in assigning geographic 3D coordinates to the pixels of the image. This enables accurate alignment and geo-positioning of multiple images, detection of moving objects and fusion of data acquired from multiple sensors. To solve this problem there are different approaches that require, in addition to a precise characterization of the camera sensor, high resolution referenced images or terrain elevation models, which are usually not publicly available or out of date. Building upon the idea of developing technology that does not need a reference terrain elevation model, we propose a geo-registration technique that applies variational methods to obtain a dense and coherent surface elevation model that is used to replace the reference model. The surface elevation model is built by interpolation of scattered 3D points, which are obtained in a two-step process following a classical stereo pipeline: first, coherent disparity maps between image pairs of a video sequence are estimated and then image point correspondences are back-projected. The proposed variational method enforces continuity of the disparity map not only along epipolar lines (as done by previous geo-registration techniques) but also across them, in the full 2D image domain. In the experiments, aerial images from synthetic video sequences have been used to validate the proposed technique.

Perfil de playas sustentadas : estudio hidrodinámico y experimental : directrices de diseño

Las playas sustentadas por medio de un pie sumergido son una atractiva alternativa de diseño de regeneración de playas especialmente cuando las condiciones física del emplazamiento o las características de la arena nativa y de préstamo producen perfiles de alimentación que no se intersectan. La observación y propuesta de este tipo de solución data de los años 1960’s, así como la experiencia internacional en la construcción de este tipo de playas. Sin embargo, a pesar de su utilización y los estudios en campo y laboratorio, no se dispone de criterios ingenieriles que apoyen el diseño de las mismas. Esta tesis consiste en un análisis experimental del perfil de playas sustentadas en un pie sumergido (o colgadas) que se concreta en una propuesta de directrices de diseño general que permiten estimar la ubicación y características geométricas del pie sumergido frente a un oleaje y material que constituye la playa determinados. En la tesis se describe el experimento bidimensional realizado en el modelo físico de fondo móvil, donde se combinan cinco tipos de oleaje con tres configuraciones del pie sumergido (“Sin estructura”, configuración baja o “Estructura 1” y configuración alta o “Estructura 2”), se presentan los resultados obtenidos y se realiza una discusión detallada de las implicaciones de los resultados desde el punto de vista hidrodinámico utilizando monomios adimensionales. Se ha realizado un análisis detallado del estado del arte sobre playas colgadas, presentando el concepto y las experiencias de realizaciones en distintos países. Se ha realizado una cuidadosa revisión de la literatura publicada sobre estudios experimentales de playas colgadas, modelos teóricos y otras cuestiones auxiliares, necesarias para la formulación de la metodología de la tesis. El estudio realizado se ha estructurado en dos fases. En la primera fase se ha realizado una experimentación en un modelo físico de fondo móvil construido en las instalaciones del Centro de Estudios de Puertos y Costas (CEPYC) del Centro de Estudios y Experimentación de Obras Públicas (CEDEX), consistente en un canal de 36 m de longitud, 3 m de anchura y 1.5 m de altura, provisto de un generador de oleaje de tipo pistón. Se ha diseñado una campaña de 15 ensayos, que se obtienen sometiendo a cinco tipos de oleaje tres configuraciones distintas de playa colgada. En los ensayos se ha medido el perfil de playa en distintos instantes hasta llegar al equilibrio, determinando a partir de esos datos el retroceso de la línea de costa y el volumen de sedimentos perdido. El tiempo total efectivo de ensayo asciende a casi 650 horas, y el número de perfiles de evolución de playa obtenidos totaliza 229. En la segunda fase se ha abordado el análisis de los resultados obtenidos con la finalidad de comprender el fenómeno, identificar las variables de las que depende y proponer unas directrices ingenieriles de diseño. Se ha estudiado el efecto de la altura de ola, del periodo del oleaje, del francobordo adimensional y del parámetro de Dean, constatándose la dificultad de comprensión del funcionamiento de estas obras ya que pueden ser beneficiosas, perjudiciales o inocuas según los casos. También se ha estudiado la respuesta del perfil de playa en función de otros monomios adimensionales, tales como el número de Reynolds o el de Froude. En el análisis se ha elegido el monomio “plunger” como el más significativo, encontrando relaciones de éste con el peralte de oleaje, la anchura de coronación adimensional, la altura del pie de playa adimensional y el parámetro de Dean. Finalmente, se propone un método de diseño de cuatro pasos que permite realizar un primer encaje del diseño funcional de la playa sustentada frente a un oleaje de características determinadas. Las contribuciones más significativas desde el punto de vista científico son: - La obtención del juego de resultados experimentales. - La caracterización del comportamiento de las playas sustentadas. - Las relaciones propuestas entre el monomio plunger y las distintas variables explicativas seleccionadas, que permiten predecir el comportamiento de la obra. - El método de diseño propuesto, en cuatro pasos, para este tipo de esquemas de defensa de costas. Perched beaches are an attractive beach nourishment design alternative especially when either the site conditions or the characteristics of both the native and the borrow sand lead to a non-intersecting profile The observation and suggestion of the use of this type of coastal defence scheme dates back to the 1960’s, as well as the international experience in the construction of this type of beaches. However, in spite of its use and the field and laboratory studies performed to-date, no design engineering guidance is available to support its design. This dissertation is based on the experimental work performed on a movable bed physical model and the use of dimensionless parameters in analyzing the results to provide general functional design guidance that allow the designer, at a particular stretch of coast - to estimate the location and geometric characteristics of the submerged sill as well as to estimate the suitable sand size to be used in the nourishment. This dissertation consists on an experimental analysis of perched beaches by means of a submerged sill, leading to the proposal of general design guidance that allows to estimate the location and geometric characteristics of the submerged sill when facing a wave condition and for a given beach material. The experimental work performed on a bi-dimensional movable bed physical model, where five types of wave conditions are combined with three configurations of the submerged sill (“No structure”, low structure or “Structure 1”, and high structure or “Structure 2”) is described, results are presented, and a detailed discussion of the results - from the hydrodynamic point of view – of the implications of the results by using dimensionless parameters is carried out. A detailed state of the art analysis about perched beaches has been performed, presenting the “perched beach concept” and the case studies of different countries. Besides, a careful revision of the literature about experimental studies on perched beaches, theoretical models, and other topics deemed necessary to formulate the methodology of this work has been completed. The study has been divided into two phases. Within the first phase, experiments on a movable-bed physical model have been developed. The physical model has been built in the Centro de Estudios de Puertos y Costas (CEPYC) facilities, Centro de Estudios y Experimentación de Obras Públicas (CEDEX). The wave flume is 36 m long, 3 m wide and 1.5 m high, and has a piston-type regular wave generator available. The test plan consisted of 15 tests resulting from five wave conditions attacking three different configurations of the perched beach. During the development of the tests, the beach profile has been surveyed at different intervals until equilibrium has been reached according to these measurements. Retreat of the shoreline and relative loss of sediment in volume have been obtained from the measurements. The total effective test time reaches nearly 650 hours, whereas the total number of beach evolution profiles measured amounts to 229. On the second phase, attention is focused on the analysis of results with the aim of understanding the phenomenon, identifying the governing variables and proposing engineering design guidelines. The effect of the wave height, the wave period, the dimensionless freeboard and of the Dean parameter have been analyzed. It has been pointed out the difficulty in understanding the way perched beaches work since they turned out to be beneficial, neutral or harmful according to wave conditions and structure configuration. Besides, the beach profile response as a function of other dimensionless parameters, such as Reynolds number or Froude number, has been studied. In this analysis, the “plunger” parameter has been selected as the most representative, and relationships between the plunger parameter and the wave steepness, the dimensionless crest width, the dimensionless crest height, and the Dean parameter have been identified. Finally, an engineering 4-step design method has been proposed, that allows for the preliminary functional design of the perched beach for a given wave condition. The most relevant contributions from the scientific point of view have been: - The acquisition of a consistent set of experimental results. - The characterization of the behavior of perched beaches. - The proposed relationships between the plunger parameter and the different explanatory variables selected, that allow for the prediction of the beach behavior. - The proposed design method, four-step method, for this type of coastal defense schemes.

Recrystallization of amorphous nano-tracks and uniform layers generated by swift-ion-beam irradiation in lithium niobate.

The thermal annealing of amorphous tracks of nanometer-size diameter generated in lithium niobate (LiNbO3) by Bromine ions at 45 MeV, i.e., in the electronic stopping regime, has been investigated by RBS/C spectrometry in the temperature range from 250°C to 350°C. Relatively low fluences have been used (<1012 cm−2) to produce isolated tracks. However, the possible effect of track overlapping has been investigated by varying the fluence between 3×1011 cm−2 and 1012 cm−2. The annealing process follows a two-step kinetics. In a first stage (I) the track radius decreases linearly with the annealing time. It obeys an Arrhenius-type dependence on annealing temperature with activation energy around 1.5 eV. The second stage (II) operates after the track radius has decreased down to around 2.5 nm and shows a much lower radial velocity. The data for stage I appear consistent with a solid-phase epitaxial process that yields a constant recrystallization rate at the amorphous-crystalline boundary. HRTEM has been used to monitor the existence and the size of the annealed isolated tracks in the second stage. On the other hand, the thermal annealing of homogeneous (buried) amorphous layers has been investigated within the same temperature range, on samples irradiated with Fluorine at 20 MeV and fluences of ∼1014 cm−2. Optical techniques are very suitable for this case and have been used to monitor the recrystallization of the layers. The annealing process induces a displacement of the crystalline-amorphous boundary that is also linear with annealing time, and the recrystallization rates are consistent with those measured for tracks. The comparison of these data with those previously obtained for the heavily damaged (amorphous) layers produced by elastic nuclear collisions is summarily discussed.

Research on intermediate band solar cells and development of experimental techniques for their characterization under concentrated illumination

Abstract This work is a contribution to the research and development of the intermediate band solar cell (IBSC), a high efficiency photovoltaic concept that features the advantages of both low and high bandgap solar cells. The resemblance with a low bandgap solar cell comes from the fact that the IBSC hosts an electronic energy band -the intermediate band (IB)- within the semiconductor bandgap. This IB allows the collection of sub-bandgap energy photons by means of two-step photon absorption processes, from the valence band (VB) to the IB and from there to the conduction band (CB). The exploitation of these low energy photons implies a more efficient use of the solar spectrum. The resemblance of the IBSC with a high bandgap solar cell is related to the preservation of the voltage: the open-circuit voltage (VOC) of an IBSC is not limited by any of the sub-bandgaps (involving the IB), but only by the fundamental bandgap (defined from the VB to the CB). Nevertheless, the presence of the IB allows new paths for electronic recombination and the performance of the IBSC is degraded at 1 sun operation conditions. A theoretical argument is presented regarding the need for the use of concentrated illumination in order to circumvent the degradation of the voltage derived from the increase in the recombi¬nation. This theory is supported by the experimental verification carried out with our novel characterization technique consisting of the acquisition of photogenerated current (IL)-VOC pairs under low temperature and concentrated light. Besides, at this stage of the IBSC research, several new IB materials are being engineered and our novel character¬ization tool can be very useful to provide feedback on their capability to perform as real IBSCs, verifying or disregarding the fulfillment of the “voltage preservation” principle. An analytical model has also been developed to assess the potential of quantum-dot (QD)-IBSCs. It is based on the calculation of band alignment of III-V alloyed heterojunc-tions, the estimation of the confined energy levels in a QD and the calculation of the de¬tailed balance efficiency. Several potentially useful QD materials have been identified, such as InAs/AlxGa1-xAs, InAs/GaxIn1-xP, InAs1-yNy/AlAsxSb1-x or InAs1-zNz/Alx[GayIn1-y]1-xP. Finally, a model for the analysis of the series resistance of a concentrator solar cell has also been developed to design and fabricate IBSCs adapted to 1,000 suns. Resumen Este trabajo contribuye a la investigación y al desarrollo de la célula solar de banda intermedia (IBSC), un concepto fotovoltaico de alta eficiencia que auna las ventajas de una célula solar de bajo y de alto gap. La IBSC se parece a una célula solar de bajo gap (o banda prohibida) en que la IBSC alberga una banda de energía -la banda intermedia (IB)-en el seno de la banda prohibida. Esta IB permite colectar fotones de energía inferior a la banda prohibida por medio de procesos de absorción de fotones en dos pasos, de la banda de valencia (VB) a la IB y de allí a la banda de conducción (CB). El aprovechamiento de estos fotones de baja energía conlleva un empleo más eficiente del espectro solar. La semejanza antre la IBSC y una célula solar de alto gap está relacionada con la preservación del voltaje: la tensión de circuito abierto (Vbc) de una IBSC no está limitada por ninguna de las fracciones en las que la IB divide a la banda prohibida, sino que está únicamente limitada por el ancho de banda fundamental del semiconductor (definido entre VB y CB). No obstante, la presencia de la IB posibilita nuevos caminos de recombinación electrónica, lo cual degrada el rendimiento de la IBSC a 1 sol. Este trabajo argumenta de forma teórica la necesidad de emplear luz concentrada para evitar compensar el aumento de la recom¬binación de la IBSC y evitar la degradación del voltage. Lo anterior se ha verificado experimentalmente por medio de nuestra novedosa técnica de caracterización consistente en la adquisicin de pares de corriente fotogenerada (IL)-VOG en concentración y a baja temperatura. En esta etapa de la investigación, se están desarrollando nuevos materiales de IB y nuestra herramienta de caracterizacin está siendo empleada para realimentar el proceso de fabricación, comprobando si los materiales tienen capacidad para operar como verdaderas IBSCs por medio de la verificación del principio de preservación del voltaje. También se ha desarrollado un modelo analítico para evaluar el potencial de IBSCs de puntos cuánticos. Dicho modelo está basado en el cálculo del alineamiento de bandas de energía en heterouniones de aleaciones de materiales III-V, en la estimación de la energía de los niveles confinados en un QD y en el cálculo de la eficiencia de balance detallado. Este modelo ha permitido identificar varios materiales de QDs potencialmente útiles como InAs/AlxGai_xAs, InAs/GaxIni_xP, InAsi_yNy/AlAsxSbi_x ó InAsi_zNz/Alx[GayIni_y]i_xP. Finalmente, también se ha desarrollado un modelado teórico para el análisis de la resistencia serie de una célula solar de concentración. Gracias a dicho modelo se han diseñado y fabricado IBSCs adaptadas a 1.000 soles.

Low-thickness high-quality aluminum nitride films for super high frequency solidly mounted resonators

We investigate the sputter growth of very thin aluminum nitride (AlN) films on iridium electrodes for electroacoustic devices operating in the super high frequency range. Superior crystal quality and low stress films with thicknesses as low as 160 nm are achieved after a radio frequency plasma treatment of the iridium electrode followed by a two-step alternating current reactive magnetron sputtering of an aluminum target, which promotes better conditions for the nucleation of well textured AlN films in the very first stages of growth. Solidly mounted resonators tuned around 8 GHz with effective electromechanical coupling factors of 5.8% and quality factors Q up to 900 are achieved.

Voltage recovery in intermediate band solar cells

The intermediate band solar cell (IBSC) is based on a novel photovoltaic concept and has a limiting efficiency of 63.2%, which compares favorably with the 40.7% efficiency of a conventional, single junction solar cell. It is characterized by a material hosting a collection of energy levels within its bandgap, allowing the cell to exploit photons with sub-bandgap energies in a two-step absorption process, thus improving the utilization of the solar spectrum. However, these intermediate levels are often regarded as an inherent source of supplementary recombination, although this harmful effect can in theory be counteracted by the use of concentrated light. We present here a novel, low-temperature characterization technique using concentrated light that reveals how the initially enhanced recombination in the IBSC is reduced so that its open-circuit voltage is completely recovered and reaches that of a conventional solar cell.

A silviculture-oriented spatio-temporal model for germination in Pinus pinea L. in the Spanish Northern Plateau based on a direct seeding experiment

Natural regeneration in Pinus pinea stands commonly fails throughout the Spanish Northern Plateau under current intensive regeneration treatments. As a result, extensive direct seeding is commonly conducted to guarantee regeneration occurrence. In a period of rationalization of the resources devoted to forest management, this kind of techniques may become unaffordable. Given that the climatic and stand factors driving germination remain unknown, tools are required to understand the process and temper the use of direct seeding. In this study, the spatio-temporal pattern of germination of P. pinea was modelled with those purposes. The resulting findings will allow us to (1) determine the main ecological variables involved in germination in the species and (2) infer adequate silvicultural alternatives. The modelling approach focuses on covariates which are readily available to forest managers. A two-step nonlinear mixed model was fitted to predict germination occurrence and abundance in P. pinea under varying climatic, environmental and stand conditions, based on a germination data set covering a 5-year period. The results obtained reveal that the process is primarily driven by climate variables. Favourable conditions for germination commonly occur in fall although the optimum window is often narrow and may not occur at all in some years. At spatial level, it would appear that germination is facilitated by high stand densities, suggesting that current felling intensity should be reduced. In accordance with other studies on P. pinea dispersal, it seems that denser stands during the regeneration period will reduce the present dependence on direct seeding.

Effect of concentration on the performance of quantum dot intermediate-band solar cells

Implementation of a high-efficiency quantum dot intermediate-band solar cell (QD-IBSC) must accompany a sufficient photocurrent generation via IB states. The demonstration of a QD-IBSC is presently undergoing two stages. The first is to develop a technology to fabricate high-density QD stacks or a superlattice of low defect density placed within the active region of a p-i-n SC, and the second is to realize half-filled IB states to maximize the photocurrent generation by two-step absorption of sub-bandgap photons. For this, we have investigated the effect of light concentration on the characteristics of QDSCs comprised of multi-layer stacks of self-organized InAs/GaNAs QDs grown with and without impurity doping in molecular beam epitaxy.

Recovery of Disruptions in Rapid Transit Networks

This paper studies the disruption management problem of rapid transit rail networks. Besides optimizing the timetable and the rolling stock schedules, we explicitly deal with the effects of the disruption on the passenger demand. We propose a two-step approach that combines an integrated optimization model (for the timetable and rolling stock) with a model for the passengers’ behavior. We report our computational tests on realistic problem instances of the Spanish rail operator RENFE. The proposed approach is able to find solutions with a very good balance between various managerial goals within a few minutes. Se estudia la gestión de las incidencias en redes de metro y cercanías. Se optimizan los horarios y la asignación del material rodante, teniendo en cuenta el comportamiento de los pasajeros. Se reallizan pruebas en varias líneas de la red de cercanías de Madrid, con resultados satisfactorios.

Using damage from 2010 Haiti earthquake for vulnerability estimation of typical structures in Port-au-Prince (Haiti).

After the 2010 Haiti earthquake, that hits the city of Port-au-Prince, capital city of Haiti, a multidisciplinary working group of specialists (seismologist, geologists, engineers and architects) from different Spanish Universities and also from Haiti, joined effort under the SISMO-HAITI project (financed by the Universidad Politecnica de Madrid), with an objective: Evaluation of seismic hazard and risk in Haiti and its application to the seismic design, urban planning, emergency and resource management. In this paper, as a first step for a structural damage estimation of future earthquakes in the country, a calibration of damage functions has been carried out by means of a two-stage procedure. After compiling a database with observed damage in the city after the earthquake, the exposure model (building stock) has been classified and through an iteratively two-step calibration process, a specific set of damage functions for the country has been proposed. Additionally, Next Generation Attenuation Models (NGA) and Vs30 models have been analysed to choose the most appropriate for the seismic risk estimation in the city. Finally in a next paper, these functions will be used to estimate a seismic risk scenario for a future earthquake.