Aspectos de la medición dinámica instantánea de emisiones de motores. Aplicación al desarrollo de un equipo portátil y una metodología para estudios de contaminación de vehículos en tráfico real.

Esta Tesis Doctoral se encuadra en el ámbito de la medida de emisiones contaminantes y de consumo de combustible en motores de combustión interna alternativos cuando se utilizan como plantas de potencia para propulsión de vehículos ligeros de carretera, y más concretamente en las medidas dinámicas con el vehículo circulando en tráfico real. En este ámbito, el objetivo principal de la Tesis es estudiar los problemas asociados a la medición en tiempo real con equipos embarcados de variables medioambientales, energéticas y de actividad, de vehículos ligeros propulsados por motores térmicos en tráfico real. Y como consecuencia, desarrollar un equipo y una metodología apropiada para este objetivo, con el fin de realizar consiguientemente un estudio sobre los diferentes factores que influyen sobre las emisiones y el consumo de combustible de vehículos turismo en tráfico real. La Tesis se comienza realizando un estudio prospectivo sobre los trabajos de otros autores relativos al desarrollo de equipos portátiles de medida de emisiones (Portable Emission Measurement Systems – PEMS), problemas asociados a la medición dinámica de emisiones y estudios de aplicación en tráfico real utilizando este tipo de equipos. Como resultado de este estudio se plantea la necesidad de disponer de un equipo específicamente diseñado para ser embarcado en un vehículo que sea capaz de medir en tiempo real las concentraciones de emisiones y el caudal de gases de escape, al mismo tiempo que se registran variables del motor, del vehículo y del entorno como son la pendiente y los datos meteorológicos. De esta forma se establecen las especificaciones y condiciones de diseño del equipo PEMS. Aunque al inicio de esta Tesis ya existían en el mercado algunos sistemas portátiles de medida de emisiones (PEMS: Portable Emissions Measurement Systems), en esta Tesis se investiga, diseña y construye un nuevo sistema propio, denominado MIVECO – PEMS. Se exponen, discuten y justifican todas las soluciones técnicas incorporadas en el sistema que incluyen los subsistema de análisis de gases, subsistemas de toma de muestra incluyendo caudalímetro de gases de escape, el subsistema de medida de variables del entorno y actividad del vehículo y el conjunto de sistemas auxiliares. El diseño final responde a las hipótesis y necesidades planteadas y se valida en uso real, en banco de rodillos y en comparación con otro equipos de medida de emisiones estacionarios y portátiles. En esta Tesis se presenta también toda la investigación que ha conducido a establecer la metodología de tratamiento de las señales registradas en tiempo real que incluye la sincronización, cálculos y propagación de errores. La metodología de selección y caracterización de los recorridos y circuitos y de las pautas de conducción, preparación del vehículo y calibración de los equipos forma también parte del legado de esta Tesis. Para demostrar la capacidad de medida del equipo y el tipo de resultados que pueden obtenerse y que son útiles para la comunidad científica, y las autoridades medioambientales en la parte final de esta Tesis se plantean y se presentan los resultados de varios estudios de variables endógenas y exógenas que afectan a las emisiones instantáneas y a los factores de emisión y consumo (g/km) como: el estilo de conducción, la infraestructura vial, el nivel de congestión del tráfico, tráfico urbano o extraurbano, el contenido de biocarburante, tipo de motor (diesel y encendido provocado), etc. Las principales conclusiones de esta Tesis son que es posible medir emisiones másicas y consumo de motores de vehículos en uso real y que los resultados permiten establecer políticas de reducción de impacto medio ambiental y de eficiencia energética, pero, se deben establecer unas metodologías precisas y se debe tener mucho cuidado en todo el proceso de calibración, medida y postratamientos de los datos. Abstract This doctoral thesis is in the field of emissions and fuel consumption measurement of reciprocating internal combustion engines when are used as power-trains for light-duty road vehicles, and especially in the real-time dynamic measurements procedures when the vehicle is being driven in real traffic. In this context, the main objective of this thesis is to study the problems associated with on-board real-time measuring systems of environmental, energy and activity variables of light vehicles powered by internal combustion engines in real traffic, and as a result, to develop an instrument and an appropriate methodology for this purpose, and consequently to make a study of the different factors which influence the emissions and the fuel consumption of passenger cars in real traffic. The thesis begins developing a prospective study on other authors’ works about development of Portable Emission Measurement Systems (PEMS), problems associated with dynamic emission measurements and application studies on actual traffic using PEMS. As a result of this study, it was shown that a measuring system specifically designed for being on-board on a vehicle, which can measure in real time emission concentrations and exhaust flow, and at the same time to record motor vehicle and environment variables as the slope and atmospheric data, is needed; and the specifications and design parameters of the equipment are proposed. Although at the beginning of this research work there were already on the market some PEMS, in this Thesis a new system is researched, designed and built, called MIVECO – PEMS, in order to meet such measurements needs. Following that, there are presented, discussed and justify all technical solutions incorporated in the system, including the gas analysis subsystem, sampling and exhaust gas flowmeter subsystem, the subsystem for measurement of environment variables and of the vehicle activity and the set of auxiliary subsystems. The final design meets the needs and hypotheses proposed, and is validated in real-life use and chassis dynamometer testing and is also compared with other stationary and on-board systems. This thesis also presents all the research that has led to the methodology of processing the set of signals recorded in real time including signal timing, calculations and error propagation. The methodology to select and characterize of the routes and circuits, the driving patterns, and the vehicle preparation and calibration of the instruments and sensors are part of the legacy of this thesis. To demonstrate the measurement capabilities of the system and the type of results that can be obtained and that are useful for the scientific community and the environmental authorities, at the end of this Thesis is presented the results of several studies of endogenous and exogenous variables that affect the instantaneous and averaged emissions and consumption factors (g/km), as: driving style, road infrastructure, the level of traffic congestion, urban and extra-urban traffic, biofuels content, type of engine (diesel or spark ignition) etc. The main conclusions of this thesis are that it is possible to measure mass emissions and consumption of vehicle engines in actual use and that the results allow us to establish policies to reduce environmental impact and improve energy efficiency, but, to establish precise methodologies and to be very careful in the entire process of calibration, measurement and data post-treatment is necessary.

Response timing in the lunge and target change in elite versus medium-level fencers.

The aim of the present work is to examine the differences between two groups of fencers with different levels of competition, elite and medium level. The timing parameters of the response reaction have been compared together with the kinetic variables which determine the sequence of segmented participation used during the lunge with a change in target during movement. A total of 30 male sword fencers participated, 13 elite and 17 medium level. Two force platforms recorded the horizontal component of the force and the start of the movement. One system filmed the movement in 3D, recording the spatial positions of 11 markers, while another system projected a mobile target over a screen. For synchronisation, an electronic signal enabled all the systems to be started simultaneously. Among the timing parameters of the reaction response, the choice reaction time (CRT) to the target change during the lunge was measured. The results revealed differences between the groups regarding the flight time, horizontal velocity at the end of the acceleration phase, and the length of the lunge, these being higher for the elite group, as well as other variables related to the temporal sequence of movement. No significant differences have been found in the simple reaction time or in CRT. According to the literature, the CRT appears to improve with sports practice, although this factor did not differentiate the elite from medium-level fencers. The coordination of fencing movements, that is, the right technique, constitutes a factor that differentiates elite fencers from medium-level ones.

Timing performances of a data acquisition system for time of flight PET

We are investigating the performances of a data acquisition system for Time of Flight PET, based on LYSO crystal slabs and 64 channels Silicon Photomultipliers matrices (1.2 cm2 of active area each). Measurements have been performed to test the timing capability of the detection system (SiPM matices coupled to a LYSO slab and the read-out electronics) with both test signal and radioactive source.

Traffic jam driving with NMV avoidance

n recent years, the development of advanced driver assistance systems (ADAS) – mainly based on lidar and cameras – has considerably improved the safety of driving in urban environments. These systems provide warning signals for the driver in the case that any unexpected traffic circumstance is detected. The next step is to develop systems capable not only of warning the driver but also of taking over control of the car to avoid a potential collision. In the present communication, a system capable of autonomously avoiding collisions in traffic jam situations is presented. First, a perception system was developed for urban situations—in which not only vehicles have to be considered, but also pedestrians and other non-motor-vehicles (NMV). It comprises a differential global positioning system (DGPS) and wireless communication for vehicle detection, and an ultrasound sensor for NMV detection. Then, the vehicle's actuators – brake and throttle pedals – were modified to permit autonomous control. Finally, a fuzzy logic controller was implemented capable of analyzing the information provided by the perception system and of sending control commands to the vehicle's actuators so as to avoid accidents. The feasibility of the integrated system was tested by mounting it in a commercial vehicle, with the results being encouraging.