Logic cells as basic structures to add/drop WDM information signals

Nowadays, in order to take advantage of fiber optic bandwidth, any optical communications system tends to be WDM. The way to extract a channel, characterized by a wavelength, from the optical fiber is to filter the specific wavelength. This gives the systems a low degree of freedom due to the fact of the static character of most of the employed devices. In this paper we will present a different way to extract channels from an optical fiber with WDM transmission. The employed method is based on an Optically Programmable Logic Cells (OPLC) previously published by us, for other applications as a chaotic generator or as basic element for optical computing. In this paper we will describe the configuration of the OPLC to be employed as a dropping device. It acts as a filter because it will extract the data carried by a concrete wavelength. It does depend, internally, on the wavelength. We will show how the intensity of the signal is able to select the chosen information from the line. It will be also demonstrated that a new idea of redundant information it is the way of selecting the concrete wavelength. As a matter of fact this idea is apparently the only way to use the OPLC as a dropping device. Moreover, based on these concepts, a similar way to route signals to different routes is reported. The basis is the use of photonic switching configurations, namely Batcher or Bayan structures, where the unit switching cells are the above indicated OPLCs.

Contribution to the Analysis, Design and Assessment of Compact Antenna Test Ranges At Millimeter Wavelengths - Contribución al Análisis, Diseño y Caracterización de Sistemas de Medida de Antenas en Rango Compacto para Frecuencias Milimétricas

This Doctoral Thesis entitled Contribution to the analysis, design and assessment of compact antenna test ranges at millimeter wavelengths aims to deepen the knowledge of a particular antenna measurement system: the compact range, operating in the frequency bands of millimeter wavelengths. The thesis has been developed at Radiation Group (GR), an antenna laboratory which belongs to the Signals, Systems and Radiocommunications department (SSR), from Technical University of Madrid (UPM). The Radiation Group owns an extensive experience on antenna measurements, running at present four facilities which operate in different configurations: Gregorian compact antenna test range, spherical near field, planar near field and semianechoic arch system. The research work performed in line with this thesis contributes the knowledge of the first measurement configuration at higher frequencies, beyond the microwaves region where Radiation Group features customer-level performance. To reach this high level purpose, a set of scientific tasks were sequentially carried out. Those are succinctly described in the subsequent paragraphs. A first step dealed with the State of Art review. The study of scientific literature dealed with the analysis of measurement practices in compact antenna test ranges in addition with the particularities of millimeter wavelength technologies. Joint study of both fields of knowledge converged, when this measurement facilities are of interest, in a series of technological challenges which become serious bottlenecks at different stages: analysis, design and assessment. Thirdly after the overview study, focus was set on Electromagnetic analysis algorithms. These formulations allow to approach certain electromagnetic features of interest, such as field distribution phase or stray signal analysis of particular structures when they interact with electromagnetic waves sources. Properly operated, a CATR facility features electromagnetic waves collimation optics which are large, in terms of wavelengths. Accordingly, the electromagnetic analysis tasks introduce an extense number of mathematic unknowns which grow with frequency, following different polynomic order laws depending on the used algorithmia. In particular, the optics configuration which was of our interest consisted on the reflection type serrated edge collimator. The analysis of these devices requires a flexible handling of almost arbitrary scattering geometries, becoming this flexibility the nucleus of the algorithmia’s ability to perform the subsequent design tasks. This thesis’ contribution to this field of knowledge consisted on reaching a formulation which was powerful at the same time when dealing with various analysis geometries and computationally speaking. Two algorithmia were developed. While based on the same principle of hybridization, they reached different order Physics performance at the cost of the computational efficiency. Inter-comparison of their CATR design capabilities was performed, reaching both qualitative as well as quantitative conclusions on their scope. In third place, interest was shifted from analysis - design tasks towards range assessment. Millimetre wavelengths imply strict mechanical tolerances and fine setup adjustment. In addition, the large number of unknowns issue already faced in the analysis stage appears as well in the on chamber field probing stage. Natural decrease of dynamic range available by semiconductor millimeter waves sources requires in addition larger integration times at each probing point. These peculiarities increase exponentially the difficulty of performing assessment processes in CATR facilities beyond microwaves. The bottleneck becomes so tight that it compromises the range characterization beyond a certain limit frequency which typically lies on the lowest segment of millimeter wavelength frequencies. However the value of range assessment moves, on the contrary, towards the highest segment. This thesis contributes this technological scenario developing quiet zone probing techniques which achieves substantial data reduction ratii. Collaterally, it increases the robustness of the results to noise, which is a virtual rise of the setup’s available dynamic range. In fourth place, the environmental sensitivity of millimeter wavelengths issue was approached. It is well known the drifts of electromagnetic experiments due to the dependance of the re sults with respect to the surrounding environment. This feature relegates many industrial practices of microwave frequencies to the experimental stage, at millimeter wavelengths. In particular, evolution of the atmosphere within acceptable conditioning bounds redounds in drift phenomena which completely mask the experimental results. The contribution of this thesis on this aspect consists on modeling electrically the indoor atmosphere existing in a CATR, as a function of environmental variables which affect the range’s performance. A simple model was developed, being able to handle high level phenomena, such as feed - probe phase drift as a function of low level magnitudes easy to be sampled: relative humidity and temperature. With this model, environmental compensation can be performed and chamber conditioning is automatically extended towards higher frequencies. Therefore, the purpose of this thesis is to go further into the knowledge of millimetre wavelengths involving compact antenna test ranges. This knowledge is dosified through the sequential stages of a CATR conception, form early low level electromagnetic analysis towards the assessment of an operative facility, stages for each one of which nowadays bottleneck phenomena exist and seriously compromise the antenna measurement practices at millimeter wavelengths.

GEODA-GRUA: Adaptive Multibeam Conformal Antenna for Satellites Communications

The GEODA-GRUA is one conformal adaptive antenna array designed for satellite communications. Operating at 1.7 GHz with circular polarization, it is possible to track and communicate with several satellites at once being able to receive signals in full azimuth and within the range of 5° to broadside elevation thanks to its adaptive beam. The complex structure of the antenna array has 2700 radiating elements based on a set of 60 similar triangular arrays that are divided in 15 subarrays of 3 radiating elements. A control module governs each transmission/receiver (T/R) module associated to each cell in order to manage beam steering by shifting phases.

Estructura de una red esencial de señalización que regula la homeostasis iónica en plantas

Las plantas son organismos sésiles que han desarrollado la capacidad para detectar variaciones sutiles en su ambiente y producir respuestas adaptativas mediante rutas de señalización. Los estímulos causados por el estrés biótico y abiótico son numerosos y dependiendo del tiempo de exposición y su intensidad, pueden reducir la tasa de crecimiento de las plantas y la producción. Los cambios en la concentración del calcio citosólico libre constituyen una de las primeras reacciones intracelulares a las situaciones de estrés abiótico. En esta situación, el calcio actúa como segundo mensajero y las variaciones en su concentración son descodificadas por proteínas de unión a calcio. Las más conocidas son las manos-EF y los dominios C2. Los dominios C2 han sido descritos como dominios de unión a lípidos dependientes de calcio. Estos dominios se consideran proteínas periféricas solubles en agua que se asocian de manera reversible a los lípidos de la membrana mediante una o dos regiones funcionales: el sitio de unión a calcio y el sitio polibásico. A pesar de que se conoce la estructura molecular de algunos dominios C2, se desconocen aspectos relacionados como las reglas que dirigen su forma de interaccionar con los diferentes fosfolípidos y proteínas, la posición que ocupan en la bicapa lipídica y su papel en la transmisión de señales. En esta tesis se ha estudiado una proteína de Arabidopsis thaliana (At3g17980) representativa de una nueva familia de proteínas con dominios C2, que consiste únicamente de un dominio C2. Esta proteína, llamada AtC2.1, ha sido clonada en el vector pETM11, expresada en E. coli y purificada a homogeneidad en dos pasos cromatográficos. Se obtuvieron cristales de AtC2.1 de buena calidad mediante técnicas de difusión de vapor. La proteína fue co-cristalizada con calcio, fosfocolina (POC) y el fosfolípido 1,2-dihexanoil-sn-glicero-3-fosfo-L-serina (PSF). Se recogieron ocho conjuntos de datos de difracción de rayos X empleando radiación sincrotrón. Los cristales difractaron hasta 1.6 Å de resolución. Siete de ellos pertenecían al grupo ortorrómbico P212121, con las dimensiones de la celdilla unidad a = 35.3, b = 88.9, c = 110.6 Å, y un cristal pertenecía al grupo espacial monoclínico C2, con a = 124.84, b = 35.27, c = 92.32 Å y = 121.70º. La estructura se resolvió mediante la técnica MR-SAD utilizando el cinc como dispersor anómalo. La estructura cristalina mostró que la molécula forma un dímero en el que cada protómero se pliega como un dominio C2 típico, con la topología tipo II y presenta una inserción de 43 aminoácidos que la diferencia de los dominios C2 conocidos. El mapa de densidad electrónica mostró dos átomos de calcio por protómero. Se resolvieron las estructuras de AtC2.1 en complejo con POC o PSF. En ambos complejos, el análisis cristalográfico detectó máximos de densidad electrónica en la región correspondiente al sitio polibásico formado por las hebras 2, 3 5 y el lazo 3. Éstos se interpretaron correctamente como dos moléculas de POC y un átomo de cinc, en un complejo, y como la cabeza polar del PSF en el otro. AtC2.1 define un sitio de interacción con lípidos dependiente de cinc. En conclusión, en este trabajo se presenta la estructura tridimensional de AtC2.1, miembro representativo de una familia de proteínas de Arabidopsis thaliana, identificadas como proteínas que interaccionan con los receptores de ABA. Estas proteínas están constituidas únicamente por un dominio C2. El análisis conjunto de los datos biofísicos y cristalográficos muestra que AtC2.1 es un sensor de calcio que une lípidos usando dos sitios funcionales. Estos datos sugieren un mecanismo de inserción en membrana dependiente de calcio que trae consigo la disociación de la estructura dimérica y, por consiguiente, un cambio en las propiedades de superficie de la molécula. Este mecanismo proporciona las bases del reconocimiento y transporte de los receptores de ABA y/o otras moléculas a la membrana celular. Plants are sessile organisms that have developed the capacity to detect slight variations of their environment. They are able to perceive biotic and abiotic stress signals and to transduce them by signaling pathways in order to trigger adaptative responses. Stress factors are numerous and, depending on their exposition time and their concentration, can reduce plant growth rate, limiting the productivity of crop plants. Changes in the cytosolic free calcium concentration are observed as one of the earliest intracellular reactions to abiotic stress signals. Calcium plays a key role as a second messenger, and calcium concentration signatures, called calcium signals, are decodified by calcium binding proteins. The main calcium binding structures are the EF-hand motif and the C2 domains. C2 domain is a calcium dependent lipid-binding domain of approximately 130 amino acids. C2 domain displays two functional regions: the Ca-binding region and the polybasic cluster. Both of them can interact with the membrane phospholipids. Despite the number of C2 domain 3D structures currently available, questions about how they interact with the different target phospholipids, their precise spatial position in the lipid bilayer, interactions with other proteins and their role in transmitting signals downstream, have not yet been explored. In this work we have studied an uncharacterized protein from Arabidopsis thaliana (At3g17980) consisting of only a single C2 domain, as member of a new protein C2-domain family. This protein called AtC2.1 was cloned into the pETM11 vector and expressed in E. coli, allowing the purification to homogeneity in two chromatographic steps. Good quality diffracting crystals were obtained using vapor-diffusion techniques. Crystals were co-crystalized with calcium; phosphocholine (POC) and/or the phospholipid 1,2-dihexanoyl-sn-glycero-3-phospho-L-serine (PSF). Eight data set were collected with synchrotron radiation. Crystals diffracted up to 1.6 Å resolution and seven of them belong to the orthorhombic space group P212121, with unit-cell parameters a = 35.3, b = 88.9, c = 110.6 Å. Another crystal was monoclinic, space group C2, with a = 124.84, b = 35.27, c = 92.32 Å and = 121.70º. The structural model was solved by MR-SAD using Zn2+ as anomalous scatterer. The crystal structure shows that the molecule is a dimer. Each monomer was folded as a canonical C2 domain with the topology II with a 43 residues insertion. The electron density map reveals two calcium ions per molecule. Structures of AtC2.1, complexed with POC and PSF, have been solved. Well-defined extra electron densities were found, in both complexes, within the concave surface formed by strands 2, 3, 5 and loop 3 of AtC2.1. These densities were clearly explained by the presence of the two POC molecules, one zinc atom and head groups of PSF, occupying the cavity of the polybasic site. AtC2.1 defines a new metal dependent lipid-binding site into the polybasic site. In conclusion, in this thesis it is presented the molecular structure of AtC2.1, a representative member of a family of Arabidopsis thaliana C2 domain proteins, of unknown function, but identified as a molecular interacting unit of the ABA receptors. The joint analyses of the biophysical and crystallographic data show that AtC2.1 is a calcium sensor that binds lipids in two sites and suggest a model of calcium-dependent membrane insertion mechanism that will involve either dimer dissociation or a strong rearrangement of the dimeric structure. This mechanism may be the basis for the recognition and delivery of ABA receptors or other protein molecules to cell membranes.

Computational methods to create and analyze a digital gene expression atlas of embryo development from microscopy images

Abstract The creation of atlases, or digital models where information from different subjects can be combined, is a field of increasing interest in biomedical imaging. When a single image does not contain enough information to appropriately describe the organism under study, it is then necessary to acquire images of several individuals, each of them containing complementary data with respect to the rest of the components in the cohort. This approach allows creating digital prototypes, ranging from anatomical atlases of human patients and organs, obtained for instance from Magnetic Resonance Imaging, to gene expression cartographies of embryo development, typically achieved from Light Microscopy. Within such context, in this PhD Thesis we propose, develop and validate new dedicated image processing methodologies that, based on image registration techniques, bring information from multiple individuals into alignment within a single digital atlas model. We also elaborate a dedicated software visualization platform to explore the resulting wealth of multi-dimensional data and novel analysis algo-rithms to automatically mine the generated resource in search of bio¬logical insights. In particular, this work focuses on gene expression data from developing zebrafish embryos imaged at the cellular resolution level with Two-Photon Laser Scanning Microscopy. Disposing of quantitative measurements relating multiple gene expressions to cell position and their evolution in time is a fundamental prerequisite to understand embryogenesis multi-scale processes. However, the number of gene expressions that can be simultaneously stained in one acquisition is limited due to optical and labeling constraints. These limitations motivate the implementation of atlasing strategies that can recreate a virtual gene expression multiplex. The developed computational tools have been tested in two different scenarios. The first one is the early zebrafish embryogenesis where the resulting atlas constitutes a link between the phenotype and the genotype at the cellular level. The second one is the late zebrafish brain where the resulting atlas allows studies relating gene expression to brain regionalization and neurogenesis. The proposed computational frameworks have been adapted to the requirements of both scenarios, such as the integration of partial views of the embryo into a whole embryo model with cellular resolution or the registration of anatom¬ical traits with deformable transformation models non-dependent on any specific labeling. The software implementation of the atlas generation tool (Match-IT) and the visualization platform (Atlas-IT) together with the gene expression atlas resources developed in this Thesis are to be made freely available to the scientific community. Lastly, a novel proof-of-concept experiment integrates for the first time 3D gene expression atlas resources with cell lineages extracted from live embryos, opening up the door to correlate genetic and cellular spatio-temporal dynamics. La creación de atlas, o modelos digitales, donde la información de distintos sujetos puede ser combinada, es un campo de creciente interés en imagen biomédica. Cuando una sola imagen no contiene suficientes datos como para describir apropiadamente el organismo objeto de estudio, se hace necesario adquirir imágenes de varios individuos, cada una de las cuales contiene información complementaria respecto al resto de componentes del grupo. De este modo, es posible crear prototipos digitales, que pueden ir desde atlas anatómicos de órganos y pacientes humanos, adquiridos por ejemplo mediante Resonancia Magnética, hasta cartografías de la expresión genética del desarrollo de embrionario, típicamente adquiridas mediante Microscopía Optica. Dentro de este contexto, en esta Tesis Doctoral se introducen, desarrollan y validan nuevos métodos de procesado de imagen que, basándose en técnicas de registro de imagen, son capaces de alinear imágenes y datos provenientes de múltiples individuos en un solo atlas digital. Además, se ha elaborado una plataforma de visualization específicamente diseñada para explorar la gran cantidad de datos, caracterizados por su multi-dimensionalidad, que resulta de estos métodos. Asimismo, se han propuesto novedosos algoritmos de análisis y minería de datos que permiten inspeccionar automáticamente los atlas generados en busca de conclusiones biológicas significativas. En particular, este trabajo se centra en datos de expresión genética del desarrollo embrionario del pez cebra, adquiridos mediante Microscopía dos fotones con resolución celular. Disponer de medidas cuantitativas que relacionen estas expresiones genéticas con las posiciones celulares y su evolución en el tiempo es un prerrequisito fundamental para comprender los procesos multi-escala característicos de la morfogénesis. Sin embargo, el número de expresiones genéticos que pueden ser simultáneamente etiquetados en una sola adquisición es reducido debido a limitaciones tanto ópticas como del etiquetado. Estas limitaciones requieren la implementación de estrategias de creación de atlas que puedan recrear un multiplexado virtual de expresiones genéticas. Las herramientas computacionales desarrolladas han sido validadas en dos escenarios distintos. El primer escenario es el desarrollo embrionario temprano del pez cebra, donde el atlas resultante permite constituir un vínculo, a nivel celular, entre el fenotipo y el genotipo de este organismo modelo. El segundo escenario corresponde a estadios tardíos del desarrollo del cerebro del pez cebra, donde el atlas resultante permite relacionar expresiones genéticas con la regionalización del cerebro y la formación de neuronas. La plataforma computacional desarrollada ha sido adaptada a los requisitos y retos planteados en ambos escenarios, como la integración, a resolución celular, de vistas parciales dentro de un modelo consistente en un embrión completo, o el alineamiento entre estructuras de referencia anatómica equivalentes, logrado mediante el uso de modelos de transformación deformables que no requieren ningún marcador específico. Está previsto poner a disposición de la comunidad científica tanto la herramienta de generación de atlas (Match-IT), como su plataforma de visualización (Atlas-IT), así como las bases de datos de expresión genética creadas a partir de estas herramientas. Por último, dentro de la presente Tesis Doctoral, se ha incluido una prueba conceptual innovadora que permite integrar los mencionados atlas de expresión genética tridimensionales dentro del linaje celular extraído de una adquisición in vivo de un embrión. Esta prueba conceptual abre la puerta a la posibilidad de correlar, por primera vez, las dinámicas espacio-temporales de genes y células.

Synchronizing chaotic optically-programmable digital circuits

In this paper an approach to the synchronization of chaotic circuits has been reported. It is based on an optically programmable logic cell and the signals involved are fully digital. It is based on the reception of the same input signal on sender and receiver and from this approach, with a posterior correlation between both outputs, an identical chaotic output is obtained in both systems. No conversion from analog to digital signals is needed. The model here presented is based on a computer simulation.

Processing of ultra-wideband low-frequency signals, for application in Foliage Penetration (FOPEN) Synthetic Aperture Radar (SAR) systems

Foliage Penetration (FOPEN) radar systems were introduced in 1960, and have been constantly improved by several organizations since that time. The use of Synthetic Aperture Radar (SAR) approaches for this application has important advantages, due to the need for high resolution in two dimensions. The design of this type of systems, however, includes some complications that are not present in standard SAR systems. FOPEN SAR systems need to operate with a low central frequency (VHF or UHF bands) in order to be able to penetrate the foliage. High bandwidth is also required to obtain high resolution. Due to the low central frequency, large integration angles are required during SAR image formation, and therefore the Range Migration Algorithm (RMA) is used. This project thesis identifies the three main complications that arise due to these requirements. First, a high fractional bandwidth makes narrowband propagation models no longer valid. Second, the VHF and UHF bands are used by many communications systems. The transmitted signal spectrum needs to be notched to avoid interfering them. Third, those communications systems cause Radio Frequency Interference (RFI) on the received signal. The thesis carries out a thorough analysis of the three problems, their degrading effects and possible solutions to compensate them. The UWB model is applied to the SAR signal, and the degradation induced by it is derived. The result is tested through simulation of both a single pulse stretch processor and the complete RMA image formation. Both methods show that the degradation is negligible, and therefore the UWB propagation effect does not need compensation. A technique is derived to design a notched transmitted signal. Then, its effect on the SAR image formation is evaluated analytically. It is shown that the stretch processor introduces a processing gain that reduces the degrading effects of the notches. The remaining degrading effect after processing gain is assessed through simulation, and an experimental graph of degradation as a function of percentage of nulled frequencies is obtained. The RFI is characterized and its effect on the SAR processor is derived. Once again, a processing gain is found to be introduced by the receiver. As the RFI power can be much higher than that of the desired signal, an algorithm is proposed to remove the RFI from the received signal before RMA processing. This algorithm is a modification of the Chirp Least Squares Algorithm (CLSA) explained in [4], which adapts it to deramped signals. The algorithm is derived analytically and then its performance is evaluated through simulation, showing that it is effective in removing the RFI and reducing the degradation caused by both RFI and notching. Finally, conclusions are drawn as to the importance of each one of the problems in SAR system design.

Study of the influence of actin-binding proteins using linear analyses of cell deformability

The actin cytoskeleton plays a key role in the deformability of the cell and in mechanosensing. Here we analyze the contributions of three major actin cross-linking proteins, myosin II, a-actinin and filamin, to cell deformability, by using micropipette aspiration of Dictyostelium cells. We examine the applicability of three simple mechanical models: for small deformation, linear viscoelasticity and drop of liquid with a tense cortex; and for large deformation, a Newtonian viscous fluid. For these models, we have derived linearized equations and we provide a novel, straightforward methodology to analyze the experiments. This methodology allowed us to differentiate the effects of the cross-linking proteins in the different regimes of deformation. Our results confirm some previous observations and suggest important relations between the molecular characteristics of the actin-binding proteins and the cell behavior: the effect of myosin is explained in terms of the relation between the lifetime of the bond to actin and the resistive force; the presence of a-actinin obstructs the deformation of the cytoskeleton, presumably mainly due to the higher molecular stiffness and to the lower dissociation rate constants; and filamin contributes critically to the global connectivity of the network, possibly by rapidly turning over crosslinks during the remodeling of the cytoskeletal network, thanks to the higher rate constants, flexibility and larger size. The results suggest a sophisticated relationship between the expression levels of actinbinding proteins, deformability and mechanosensing.

The correlation between white-matter microstructure and the complexity of spontaneous brain activity: A difussion tensor imaging-MEG study

The advent of new signal processing methods, such as non-linear analysis techniques, represents a new perspective which adds further value to brain signals' analysis. Particularly, Lempel–Ziv's Complexity (LZC) has proven to be useful in exploring the complexity of the brain electromagnetic activity. However, an important problem is the lack of knowledge about the physiological determinants of these measures. Although acorrelation between complexity and connectivity has been proposed, this hypothesis was never tested in vivo. Thus, the correlation between the microstructure of the anatomic connectivity and the functional complexity of the brain needs to be inspected. In this study we analyzed the correlation between LZC and fractional anisotropy (FA), a scalar quantity derived from diffusion tensors that is particularly useful as an estimate of the functional integrity of myelinated axonal fibers, in a group of sixteen healthy adults (all female, mean age 65.56 ± 6.06 years, intervals 58–82). Our results showed a positive correlation between FA and LZC scores in regions including clusters in the splenium of the corpus callosum, cingulum, parahipocampal regions and the sagittal stratum. This study supports the notion of a positive correlation between the functional complexity of the brain and the microstructure of its anatomical connectivity. Our investigation proved that a combination of neuroanatomical and neurophysiological techniques may shed some light on the underlying physiological determinants of brain's oscillations

Genomic analyses of flowering transition and inflorescence development in grapevine = Análisis genómicos de la transición floral y del desarrollo de la inflorescencia en la vid

The general objective of this work is to analyze the regulatory processes underlying flowering transition and inflorescence and flower development in grapevine. Most of these crucial developmental events take place within buds growing during two seasons in two consecutive years. During the first season, the shoot apical meristem within the bud differentiates all the basic elements of the shoot including flowering transition in lateral primordia and development of inflorescence primordia. These events practically end with bud dormancy. The second season, buds resume shoot growth associated to flower formation and development. In grapevine, the lateral meristems can give rise either to tendril or inflorescence primordia that are homologous organs. With this purpose, we performed global transcriptome analyses along the bud annual cycle and during inflorescence and tendril development. In addition, we approach the genomic analysis of the MIKC type MADS-box gene family in grapevine to identify all its members and assign them putative biological functions. Regarding buds developmental cycle, the results indicate that the main factors explaining the global gene expression differences were the processes of bud dormancy and active growth as well as stress responses. Non dormant buds exhibited up-regulation in functional categories typical of actively proliferating and growing cells (photosynthesis, cell cycle regulation, chromatin assembly) whereas in dormant ones the main functional categories up-regulated were associated to stress response pathways together with transcripts related to starch catabolism. Major transcriptional changes during the dormancy period were associated to the para/endodormancy, endo/ecodormancy and ecodormancy/bud break transitions. Global transcriptional analyses along tendril and inflorescence development suggested that these two homologous organs share a common transcriptional program related to cell proliferation functions. Both structures showed a progressive decrease in the expression of categories such as cell-cycle, auxin metabolism/signaling, DNA metabolism, chromatin assembly and a cluster of five transcripts belonging to the GROWTH-REGULATING FACTOR (GRF) transcription factor family, that are known to control cell proliferation in other species and determine the size of lateral organs. However, they also showed organ specific transcriptional programs that can be related to their differential organ structure and function. Tendrils showed higher transcription of genes related to photosynthesis, hormone signaling and secondary metabolism than inflorescences, while inflorescences have higher transcriptional activity for genes encoding transcription factors (especially those belonging to the MADS-box gene family). Further analysis along inflorescence development evidenced the relevance of additional functions likely related to processes of flower development such as fatty acid and lipid metabolism, jasmonate signaling and oxylipin biosynthesis. The transcriptional analyses performed highlighted the relevance of several groups of transcriptional regulators in the developmental processes studied. The expression profiles along bud development revealed significant differences for some MADS-box subfamilies in relation to other plant species, like the members of the FLC and SVP subfamilies suggesting new roles for these groups in grapevine. In this way, it was found that VvFLC2 and VvAGL15.1 could participate, together with some members of the SPL-L family, in dormancy regulation, as was shown for some of them in other woody plants. Similarly, the expression patterns of the VvFLC1, VvFUL, VvSOC1.1 (together with VvFT, VvMFT1 and VFL) genes could indicate that they play a role in flowering transition in grapevine, in parallel to their roles in other plant systems. The expression levels of VFL, the grapevine LEAFY homolog, could be crucial to specify the development of inflorescence and flower meristems instead of tendril meristems. MADS-box genes VvAP3.1 and 2, VvPI, VvAG1 and 3, VvSEP1-4, as well as VvBS1 and 2 are likely associated with the events of flower meristems and flower organs differentiation, while VvAP1 and VvFUL-L (together with VvSOC1.1, VvAGL6.2) could be involved on tendril development given their expression patterns. In addition, the biological function ofVvAP1 and VvTFL1A was analyzed using a gene silencing approach in transgenic grapevine plants. Our preliminary results suggested a possible role for both genes in the initiation and differentiation of tendrils. Finally, the genomic analysis of the MADS-box gene family in grapevine revealed differential features regarding number and expression pattern of genes putatively involved in the flowering transition process as compared to those involved in the specification of flower and fruit organ identity. Altogether, the results obtained allow identifying putative candidate genes and pathways regulating grapevine reproductive developmental processes paving the way to future experiments demonstrating specific gene biological functions. RESUMEN El objetivo general de este trabajo es analizar los procesos regulatorios subyacentes a la inducción floral así como al desarrollo de la inflorescencia y la flor en la vid. La mayor parte de estos eventos cruciales tienen lugar en las yemas a lo largo de dos estaciones de crecimiento consecutivas. Durante la primera estación, el meristemo apical contenido en la yema diferencia los elementos básicos del pámpano, lo cual incluye la inducción de la floración en los meristemos laterales y el subsiguiente desarrollo de primordios de inflorescencia. Estos procesos prácticamente cesan con la entrada en dormición de la yema. En la segunda estación, se reanuda el crecimiento del pámpano acompañado por la formación y desarrollo de las flores. En la vid, los meristemos laterales pueden dar lugar a primordios de inflorescencia o de zarcillo que son considerados órganos homólogos. Con este objetivo llevamos a cabo un estudio a nivel del transcriptoma de la yema a lo largo de su ciclo anual, así como a lo largo del desarrollo de la inflorescencia y del zarcillo. Además realizamos un análisis genómico de la familia MADS de factores transcripcionales (concretamente aquellos del tipo MIKC) para identificar todos sus miembros y tratar de asignarles posibles funciones biológicas. En cuanto al ciclo de desarrollo de la yema, los resultados indican que los principales factores que explican las diferencias globales en la expresión génica fueron los procesos de dormición de la yema y el crecimiento activo junto con las respuestas a diversos tipos de estrés. Las yemas no durmientes mostraron un incremento en la expresión de genes contenidos en categorías funcionales típicas de células en proliferación y crecimiento activo (como fotosíntesis, regulación del ciclo celular, ensamblaje de cromatina), mientras que en las yemas durmientes, las principales categorías funcionales activadas estaban asociadas a respuestas a estrés, así como con el catabolismo de almidón. Los mayores cambios observados a nivel de transcriptoma en la yema coincidieron con las transiciones de para/endodormición, endo/ecodormición y ecodormición/brotación. Los análisis transcripcionales globales a lo largo del desarrollo del zarcillo y de la inflorescencia sugirieron que estos dos órganos homólogos comparten un programa transcripcional común, relacionado con funciones de proliferación celular. Ambas estructuras mostraron un descenso progresivo en la expresión de genes pertenecientes a categorías funcionales como regulación del ciclo celular, metabolismo/señalización por auxinas, metabolismo de ADN, ensamblaje de cromatina y un grupo de cinco tránscritos pertenecientes a la familia de factores transcripcionales GROWTH-REGULATING FACTOR (GRF), que han sido asociados con el control de la proliferación celular y en determinar el tamaño de los órganos laterales en otras especies. Sin embargo, también pusieron de manifiesto programas transcripcionales que podrían estar relacionados con la diferente estructura y función de dichos órganos. Los zarcillos mostraron mayor actividad transcripcional de genes relacionados con fotosíntesis, señalización hormonal y metabolismo secundario que las inflorescencias, mientras que éstas presentaron mayor actividad transcripcional de genes codificantes de factores de transcripción (especialmente los pertenecientes a la familia MADS-box). Análisis adicionales a lo largo del desarrollo de la inflorescencia evidenciaron la relevancia de otras funciones posiblemente relacionadas con el desarrollo floral, como el metabolismo de lípidos y ácidos grasos, la señalización mediada por jasmonato y la biosíntesis de oxilipinas. Los análisis transcripcionales llevados a cabo pusieron de manifiesto la relevancia de varios grupos de factores transcripcionales en los procesos estudiados. Los perfiles de expresión estudiados a lo largo del desarrollo de la yema mostraron diferencias significativas en algunas de las subfamilias de genes MADS con respecto a otras especies vegetales, como las observadas en los miembros de las subfamilias FLC y SVP, lo cual sugiere que podrían desempeñar nuevas funciones en la vid. En este sentido, se encontró que los genes VvFLC2 y VvAGL15.1 podrían participar, junto con algunos miembros de la familia SPL-L, en la regulación de la dormición. De un modo similar, los patrones de expresión de los genes VvFLC1, VvFUL, VvSOC1.1 (junto con VvFT, VvMFT1 y VFL) podría indicar que desempeñan un papel en la regulación de la inducción de la floración en la vid, como se ha observado en otros sistemas vegetales. Los niveles de expresión de VFL, el homólogo en vid del gen LEAFY de A. thaliana podrían ser cruciales para la especificación del desarrollo de meristemos de inflorescencia y flor en lugar de meristemos de zarcillo. Los genes VvAP3.1 y 2, VvPI, VvAG1 y 3, VvSEP1-4, así como VvBS1 y 2 parecen estar asociados con los eventos de diferenciación de meristemos y órganos florales, mientras que VvAP1 y VvFUL-L (junto con VvSOC1.1 y VvAGL6.2) podrían estar implicados en el desarrollo del zarcillo dados sus patrones de expresión. Adicionalmente, se analizó la función biológica de los genes VvAP1 y VvTFL1A por medio de una estrategia de silenciamiento génico. Los datos preliminares sugieren un posible papel para ambos genes en la iniciación y diferenciación de los zarcillos. Finalmente, el análisis genómico de la familia MADS en vid evidenció diferencias con respecto a otras especies vegetales en cuanto a número de miembros y patrón de expresión en genes supuestamente implicados en la inducción de la floración, en comparación con aquellos relacionados con la especificación de identidad de órganos florales y desarrollo del fruto. En conjunto, los resultados obtenidos han permitido identificar posibles rutas y genes candidatos a participar en la regulación de los procesos de desarrollo reproductivo de la vid, sentando las bases de futuros experimentos encaminados a conocer la funciones biológicas de genes específicos.

Strange attractor in optical logic cells

Optical logic cells, employed in several tasks as optical computing or optically controlled switches for photonic switching, offer a very particular behavior when the working conditions are slightly modified. One of the more striking changes occurs when some delayed feedback is applied between one of the possible output gates and a control input. Some of these new phenomena have been studied by us and reported in previous papers. A chaotic behavior is one of the more characteristic results and its possible applications range from communications to cryptography. But the main problem related with this behavior is the binary character of the resulting signal. Most of the nowadays-employed techniques to analyze chaotic signals concern to analogue signals where algebraic equations are possible to obtain. There are no specific tools to study digital chaotic signals. Some methods have been proposed. One of the more used is equivalent to the phase diagram in analogue chaos. The binary signal is converted to hexadecimal and then analyzed. We represented the fractal characteristics of the signal. It has the characteristics of a strange attractor and gives more information than the obtained from previous methods. A phase diagram, as the one obtained by previous techniques, may fully cover its surface with the trajectories and almost no information may be obtained from it. Now, this new method offers the evolution around just a certain area being this lines the strange attractor.

Photonic switching architectures with logic cells

Possible switching architectures, with Optically Programmable Logic Cells - OPLCs - will be reported in this paper. These basic units, previously employed by us for some other applications mainly in optical computing, will be employed as main elements to switch optical communications signals. The main aspect to be considered is that because the nternal components of these cells have nonlinear behaviors, namely either pure bistable or SEED-like properties, several are the possibilities to be obtained. Moreover, because their properties are dependent, under certain condition, of the signal wavelength, they are apt to be employed in WDM systems and the final result will depend on the orresponding optical signal frequency. We will give special emphasis to the case where self-routing is achieved, namely to structures of the Batcher or Banyan type. In these cases, as it will be shown, there is the possibility to route any packet input to a certain direction according to its first bits. The number of possible outputs gives the number of bits needed to route signals. An advantage of this configuration is that a very versatile behavior may be allowed. The main one is the possibility to obtain configurations with different kinds of behavior, namely, Strictly Nonblocking, Wide-Sense Nonblocking or Rearrangeably Nonblocking as well as to eliminate switching conflicts at a certain intermediate stages.

Global optimization of solar thermophotovoltaic systems

n this paper, we present a theoretical model based on the detailed balance theory of solar thermophotovoltaic systems comprising multijunction photovoltaic cells, a sunlight concentrator and spectrally selective surfaces. The full system has been defined by means of 2n + 8 variables (being n the number of sub-cells of the multijunction cell). These variables are as follows: the sunlight concentration factor, the absorber cut-off energy, the emitter-to-absorber area ratio, the emitter cut-off energy, the band-gap energy(ies) and voltage(s) of the sub-cells, the reflectivity of the cells' back-side reflector, the emitter-to-cell and cell-to-cell view factors and the emitter-to-cell area ratio. We have used this model for carrying out a multi-variable system optimization by means of a multidimensional direct-search algorithm. This analysis allows to find the set of system variables whose combined effects results in the maximum overall system efficiency. From this analysis, we have seen that multijunction cells are excellent candidates to enhance the system efficiency and the electrical power density. Particularly, multijunction cells report great benefits for systems with a notable presence of optical losses, which are unavoidable in practical systems. Also, we have seen that the use of spectrally selective absorbers, rather than black-body absorbers, allows to achieve higher system efficiencies for both lower concentration and lower emitter-to-absorber area ratio. Finally, we have seen that sun-to-electricity conversion efficiencies above 30% and electrical power densities above 50 W/cm2 are achievable for this kind of systems.

Metodología de Ejecución y Explotación de los Ensayos en Vuelo de Flameo

El flameo o flutter es un fenómeno vibratorio debido a la interacción de fuerzas inerciales, elásticas y aerodinámicas. Consiste en un intercambio de energía, que se puede observar en el cambio de amortiguamientos, entre dos o más modos estructurales, denominados modos críticos, cuyas frecuencias tienden a acercarse (coalescencia de frecuencias). Los ensayos en vuelo de flameo suponen un gran riesgo debido a la posibilidad de una perdida brusca de estabilidad aeroelástica (flameo explosivo) con la posibilidad de destrucción de la aeronave. Además existen otros fenómenos asociados que pueden aparecer como el LCO (Limit Cycle Oscillation) y la interacción con los mandos de vuelo. Debido a esto, se deben llevar a cabo análisis exhaustivos, que incluyen GVT (vibraciones en tierra), antes de comenzar los ensayos en vuelo, y estos últimos deben ser ejecutados con robustos procedimientos. El objetivo de los ensayos es delimitar la frontera de estabilidad sin llegar a ella, manteniéndose siempre dentro de la envolvente estable de vuelo. Para lograrlo se necesitan métodos de predicción, siendo el “Flutter Margin”, el más utilizado. Para saber cuánta estabilidad aeroelástica tiene el avión y lo lejos que está de la frontera de estabilidad (a través de métodos de predicción) los parámetros modales, en particular la frecuencia y el amortiguamiento, son de vital importancia. El ensayo en vuelo consiste en la excitación de la estructura a diferentes condiciones de vuelo, la medición de la respuesta y su análisis para obtener los dos parámetros mencionados. Un gran esfuerzo se dedica al análisis en tiempo real de las señales como un medio de reducir el riesgo de este tipo de ensayos. Existen numerosos métodos de Análisis Modal, pero pocos capaces de analizar las señales procedentes de los ensayos de flameo, debido a sus especiales características. Un método novedoso, basado en la Descomposición por Valores Singulares (SVD) y la factorización QR, ha sido desarrollado y aplicado al análisis de señales procedentes de vuelos de flameo del F-18. El método es capaz de identificar frecuencia y amortiguamiento de los modos críticos. El algoritmo se basa en la capacidad del SVD para el análisis, modelización y predicción de series de datos con características periódicas y en su capacidad de identificar el rango de una matriz, así como en la aptitud del QR para seleccionar la mejor base vectorial entre un conjunto de vectores para representar el campo vectorial que forman. El análisis de señales de flameo simuladas y reales demuestra, bajo ciertas condiciones, la efectividad, robustez, resistencia al ruido y capacidad de automatización del método propuesto. ABSTRACT Flutter involves the interaction between inertial, elastic and aerodynamic forces. It consists on an exchange of energy, identified by change in damping, between two or more structural modes, named critical modes, whose frequencies tend to get closer to each other (frequency coalescence). Flight flutter testing involves high risk because of the possibility of an abrupt lost in aeroelastic stability (hard flutter) that may lead to aircraft destruction. Moreover associated phenomena may happen during the flight as LCO (Limit Cycle Oscillation) and coupling with flight controls. Because of that, intensive analyses, including GVT (Ground Vibration Test), have to be performed before beginning the flights test and during them consistent procedures have to be followed. The test objective is to identify the stability border, maintaining the aircraft always inside the stable domain. To achieve that flutter speed prediction methods have to be used, the most employed being the “Flutter Margin”. In order to know how much aeroelastic stability remains and how far the aircraft is from the stability border (using the prediction methods), modal parameters, in particular frequency and damping are paramount. So flight test consists in exciting the structure at various flight conditions, measuring the response and identifying in real-time these two parameters. A great deal of effort is being devoted to real-time flight data analysis as an effective way to reduce the risk. Numerous Modal Analysis algorithms are available, but very few are suitable to analyze signals coming from flutter testing due to their special features. A new method, based on Singular Value Decomposition (SVD) and QR factorization, has been developed and applied to the analysis of F-18 flutter flight-test data. The method is capable of identifying the frequency and damping of the critical aircraft modes. The algorithm relies on the capability of SVD for the analysis, modelling and prediction of data series with periodic features and also on its power to identify matrix rank as well as QR competence for selecting the best basis among a set of vectors in order to represent a given vector space of such a set. The analysis of simulated and real flutter flight test data demonstrates, under specific conditions, the effectiveness, robustness, noise-immunity and the capability for automation of the method proposed.

Detector de banda ultraancha en tecnología microstrip hasta 40 GHz

Detectors designing is a key aspect for the development of the new millimeter wave systems. In this paper two detectors in microstrip technology are presented. They use zero bias Schottky diodes to detect signals from low frequency to 40 GHz. High sensibility, flat frequency response and ultrabroadband are the main features of these designs. They are also cheap and easy to mount because they have been built using microstrip technology. This paper explains most technological questions which must be taken into account to design such detectors.