Controlled time of arrival feasibility analysis

Previous research studies and operational trials have shown that using the airborne Required Time of Arrival (RTA) function, an aircraft can individually achieve an assigned time to a metering or merge point accurately. This study goes a step further and investigates the application of RTA to a real sequence of arriving aircraft into Melbourne Australia. Assuming that the actual arrival times were Controlled Time of Arrivals (CTAs) assigned to each aircraft, the study examines if the airborne RTA solution would work. Three scenarios were compared: a baseline scenario being the actual flown trajectories in a two hour time-span into Melbourne, a scenario in which the sequential landing slot times of the baseline scenario were assigned as CTAs and a third scenario in which the landing slots could be freely redistributed to the inbound traffic as CTAs. The research found that pressure on the terminal area would sometimes require aircraft to lose more time than possible through the RTA capability. Using linear holding as an additional measure to absorb extensive delays, up to 500NM (5%) of total track reduction and 1300kg (3%) of total fuel consumption could be saved in the scenario with landing slots freely distributed as CTAs, compared to the baseline scenario. Assigning CTAs in an arrival sequence requires the ground system to have an accurate trajectory predictor to propose additional delay measures (path stretching, linear holding) if necessary. Reducing the achievable time window of the aircraft to add control margin to the RTA function, had a negative impact and increased the amount of intervention other than speed control required to solve the sequence. It was concluded that the RTA capability is not a complete solution but merely a tool to assist in managing the increasing complexity of air traffic.

Effect of control method on impedance-based interactions in a buck converter

All the interconnected regulated systems are prone to impedance-based interactions making them sensitive to instability and transient-performance degradation. The applied control method affects significantly the characteristics of the converter in terms of sensitivity to different impedance interactions. This paper provides for the first time the whole set of impedance-type internal parameters and the formulas according to which the interaction sensitivity can be fully explained and analyzed. The formulation given in this paper can be utilized equally either based on measured frequency responses or on predicted analytic transfer functions. Usually, the distributed dc-dc systems are constructed by using ready-made power modules without having thorough knowledge on the actual power-stage and control-system designs. As a consequence, the interaction characterization has to be based on the frequency responses measureable via the input and output terminals. A buck converter with four different control methods is experimentally characterized in frequency domain to demonstrate the effect of control method on the interaction sensitivity. The presented analytical models are used to explain the phenomena behind the changes in the interaction sensitivity.

Atmospheric Propagation at 100 and 300 GHz: Assessment of a Method to Identify Rainy Conditions during Radiosoundings

The influence of atmospheric gases and tropospheric phenomena becomes more relevant at frequencies within the THz band (100 GHz to 10 THz), severely affecting the propagation conditions. The use of radiosoundings in propagation studies is a well established measurement technique in order to collect information about the vertical structure of the atmosphere, from which gaseous and cloud attenuation can be estimated with the use of propagation models. However, some of these prediction models are not suitable to be used under rainy conditions. In the present study, a method to identify the presence of rainy conditions during radiosoundings is introduced, with the aim of filtering out these events from yearly statistics of predicted atmospheric attenuation. The detection procedure is based on the analysis of a set of parameters, some of them extracted from synoptical observations of weather (SYNOP reports) and other derived from radiosonde observations (RAOBs). The performance of the method has been evaluated under different climatic conditions, corresponding to three locations in Spain, where colocated rain gauge data were available. Rain events detected by the method have been compared with those precipitations identified by the rain gauge. The pertinence Received 26 June 2012, Accepted 31 July 2012, Scheduled 15 August 2012 * Corresponding author: Gustavo Adolfo Siles Soria (gsiles@grc.ssr.upm.es). 258 Siles et al. of the method is discussed on the basis of an analysis of cumulative distributions of total attenuation at 100 and 300 GHz. This study demonstrates that the proposed method can be useful to identify events probably associated to rainy conditions. Hence, it can be considered as a suitable algorithm in order to filter out this kind of events from annual attenuation statistics.

Timing performances of a data acquisition system for time of flight PET

We are investigating the performances of a data acquisition system for Time of Flight PET, based on LYSO crystal slabs and 64 channels Silicon Photomultipliers matrices (1.2 cm2 of active area each). Measurements have been performed to test the timing capability of the detection system (SiPM matices coupled to a LYSO slab and the read-out electronics) with both test signal and radioactive source.

Hummingbird: Privacy at the time of Twitter

In the last several years, micro-blogging Online Social Networks (OSNs), such as Twitter, have taken the world by storm, now boasting over 100 million subscribers. As an unparalleled stage for an enormous audience, they offer fast and reliable centralized diffusion of pithy tweets to great multitudes of information-hungry and always-connected followers. At the same time, this information gathering and dissemination paradigm prompts some important privacy concerns about relationships between tweeters, followers and interests of the latter. In this paper, we assess privacy in today?s Twitter-like OSNs and describe an architecture and a trial implementation of a privacy-preserving service called Hummingbird. It is essentially a variant of Twitter that protects tweet contents, hashtags and follower interests from the (potentially) prying eyes of the centralized server. We argue that, although inherently limited by Twitter?s mission of scalable information-sharing, this degree of privacy is valuable. We demonstrate, via a working prototype, that Hummingbird?s additional costs are tolerably low. We also sketch out some viable enhancements that might offer better privacy in the long term.

Assessing the landscape value of public works: validation of the method in the lowlands of the middle section of the Tajo river (Spain)

This paper proposes a method of landscape characterisation and assessment of public works associated with fluvial landscapes, which is validated in the middle section of the Tajo River. In this method, a set of criteria is identified that unifies various characteristics of the landscape associated to the infrastructures. A specific weight is then assigned to each criterion in such a way as to produce a semi-quantitative value ranging from a minimum value of 0 to a maximum value of 10. Taken together, these criteria enable us to describe and assess the value of the public works selected for study, in this case helping us to evaluate the sections of the River Tajo analysed in our study area. Accordingly, the value of all the infrastructures associated to a stretch of the river covering several hundred kilometres was determined and after dividing this stretch into sections, they were compared under equivalent conditions to provide a hierarchal ranking.

Energy payback time of grid connected pv systems: comparison between tracking and fixed systems

A review of existing studies about LCA of PV systems has been carried out. The data from this review have been completed with our own figures in order to calculate the Energy Payback Time of double and horizontal axis tracking and fixed systems. The results of this metric span from 2 to 5 years for the latitude and global irradiation ranges of the geographical area comprised between −10◦ to 10◦ of longitude, and 30◦ to 45◦ of latitude. With the caution due to the uncertainty of the sources of information, these results mean that a GCPVS is able to produce back the energy required for its existence from 6 to 15 times during a life cycle of 30 years. When comparing tracking and fixed systems, the great importance of the PV generator makes advisable to dedicate more energy to some components of the system in order to increase the productivity and to obtain a higher performance of the component with the highest energy requirement. Both double axis and horizontal axis trackers follow this way, requiring more energy in metallic structure, foundations and wiring, but this higher contribution is widely compensated by the improved productivity of the system.

Effects of irrigation and time of application on the yield and quality of cv. Cabernet sauvignon in a warm climate

Mediterranean climate is characterized by hot summer, high evapotranspiration rates, and scarce precipitations (400 mm per year) during grapevine cycle. These extremely dry conditions affect vineyard productivity and sustainability. Supplementary irrigation is a needed practice in order to maintain yield and quality. Almost all Spanish grape growing regions are characterized by these within this context, especially in the center region, where this study was performed. The main objective of this work was to study the influence of irrigation on yield and quality. For this aim, we applied different levels of irrigation (mm of water applied) during different stages of growth and berry maturity. Four experimental treatments were applied considering the amount of water and the moment of the application: T1: Water irrigation (420 mm) applied from bloom to maturity. T2: Corresponded to the traditional irrigation scheduling, from preveraison to maturity (154 mm). T3: Water irrigation from bloom to preveraison, and water deficit from veraison to maturity (312 mm). T4: Irrigation applied from preveraison to maturity (230 mm) Experimental vineyard, cv. Cabernet Sauvignon, was located in a commercial vineyard (Bodegas Licinia S.L.) in the hot region of Morata de Tajuña (Madrid). The trial was performed during 2010 and 2011 seasons. Our results showed that yield increased from 2010 to 2011 in the treatments with a higher amount of water appli ed, T1 and T3 (24 and 10 % of yield increase respectively). This was mainly due to an increase in bud fertility (nº of bunches per shoot). Furthermore, sugar content was higher in T3 (27.3 ºBrix), followed by T2 (27 ºBrix). By contrast, T4 (irrigation from veraison) presented the lowest solid soluble concentration and the highest acidity. These results suggest that grapevine has an intrinsic capacity to adapt to its environment. However, this adaptation capacity should be evaluated considering the sensibility of quality parameters during the maturity period (acidity, pH, aroma, color...) and its impact on yield. Here, we demonstrated that a higher amount of water irrigation applied was no linked to a negative effect on quality.

Development of a method of assessment of the problem-solving competence at the technical University of Madrid.

The competence evaluation promoted by the European High Education Area entails a very important methodological change that requires guiding support to help lecturers carry out this new and complex task. In this regard, the Technical University of Madrid (UPM, by its Spanish acronym) has financed a series of coordinated projects with the objective of developing a model for teaching and evaluating core competences and providing support to lecturers. This paper deals with the problem-solving competence. The first step has been to elaborate a guide for teachers to provide a homogeneous way to asses this competence. This guide considers several levels of acquisition of the competence and provides the rubrics to be applied for each one. The guide has been subsequently validated with several pilot experiences. In this paper we will explain the problem-solving assessment guide for teachers and will show the pilot experiences that has been carried out. We will finally justify the validity of the method to assess the problem-solving competence.

Concept of operations for ATM by managing uncertainty through multiple metering points

This paper presents an operational concept for Air Traffic Management, and in particular arrival management, in which aircraft are permitted to operate in a manner consistent with current optimal aircraft operating techniques. The proposed concept allows aircraft to descend in the fuel efficient path managed mode and with arrival time not actively controlled. It will be demonstrated how the associated uncertainty in the time dimension of the trajectory can be managed through the application of multiple metering points strategically chosen along the trajectory. The proposed concept does not make assumptions on aircraft equipage (e.g. time of arrival control), but aims at handling mixed-equipage scenarios that most likely will remain far into the next decade and arguably beyond.

Efficient speed advisories for multi-stage-metering arrival management

This paper presents a methodology and algorithm for Air Traffic Control (ATC) to efficiently achieve schedules arrival times through speed control in the presence of uncertainty. The methodology does not assume the availability of airborne time of arrival control and can therefore be applied to legacy aircraft. The speed advisories are calculated in a manner that allows for sufficient control margin to, if required, adjust the aircraft's trajectory at a later stage to correct for estimated arrival time drift at the lowest impact to efficiency. The methodology is therefore envisioned to prevent major last-minute interventions and instead assists ATC in allowing more continuous descent approaches to be conducted by aircraft leading to more efficient operations.

Contributions to trajectory prediction theory and its application to arrival management for air traffic control

La gestión del tráfico aéreo (Air Traffic Management, ATM) está experimentando un cambio de paradigma hacia las denominadas operaciones basadas trayectoria. Bajo dicho paradigma se modifica el papel de los controladores de tráfico aéreo desde una operativa basada su intervención táctica continuada hacia una labor de supervisión a más largo plazo. Esto se apoya en la creciente confianza en las soluciones aportadas por las herramientas automatizadas de soporte a la decisión más modernas. Para dar soporte a este concepto, se precisa una importante inversión para el desarrollo, junto con la adquisición de nuevos equipos en tierra y embarcados, que permitan la sincronización precisa de la visión de la trayectoria, basada en el intercambio de información entre ambos actores. Durante los últimos 30 a 40 años las aerolíneas han generado uno de los menores retornos de la inversión de entre todas las industrias. Sin beneficios tangibles, la industria aérea tiene dificultades para atraer el capital requerido para su modernización, lo que retrasa la implantación de dichas mejoras. Esta tesis tiene como objetivo responder a la pregunta de si las capacidades actualmente instaladas en las aeronaves comerciales se pueden aplicar para lograr la sincronización de la trayectoria con el nivel de calidad requerido. Además, se analiza en ella si, conjuntamente con mejoras en las herramientas de predicción trayectorias instaladas en tierra en para facilitar la gestión de las arribadas, dichas capacidades permiten obtener los beneficios esperados en el marco de las operaciones basadas en trayectoria. Esto podría proporcionar un incentivo para futuras actualizaciones de la aviónica que podrían llevar a mejoras adicionales. El concepto operacional propuesto en esta tesis tiene como objetivo permitir que los aviones sean pilotados de una manera consistente con las técnicas actuales de vuelo optimizado. Se permite a las aeronaves que desciendan en el denominado “modo de ángulo de descenso gestionado” (path-managed mode), que es el preferido por la mayoría de las compañías aéreas, debido a que conlleva un reducido consumo de combustible. El problema de este modo es que en él no se controla de forma activa el tiempo de llegada al punto de interés. En nuestro concepto operacional, la incertidumbre temporal se gestiona en mediante de la medición del tiempo en puntos estratégicamente escogidos a lo largo de la trayectoria de la aeronave, y permitiendo la modificación por el control de tierra de la velocidad de la aeronave. Aunque la base del concepto es la gestión de las ordenes de velocidad que se proporcionan al piloto, para ser capaces de operar con los niveles de equipamiento típicos actualmente, dicho concepto también constituye un marco en el que la aviónica más avanzada (por ejemplo, que permita el control por el FMS del tiempo de llegada) puede integrarse de forma natural, una vez que esta tecnología este instalada. Además de gestionar la incertidumbre temporal a través de la medición en múltiples puntos, se intenta reducir dicha incertidumbre al mínimo mediante la mejora de las herramienta de predicción de la trayectoria en tierra. En esta tesis se presenta una novedosa descomposición del proceso de predicción de trayectorias en dos etapas. Dicha descomposición permite integrar adecuadamente los datos de la trayectoria de referencia calculada por el Flight Management System (FMS), disponibles usando Futuro Sistema de Navegación Aérea (FANS), en el sistema de predicción de trayectorias en tierra. FANS es un equipo presente en los aviones comerciales de fuselaje ancho actualmente en la producción, e incluso algunos aviones de fuselaje estrecho pueden tener instalada avionica FANS. Además de informar automáticamente de la posición de la aeronave, FANS permite proporcionar (parte de) la trayectoria de referencia en poder de los FMS, pero la explotación de esta capacidad para la mejora de la predicción de trayectorias no se ha estudiado en profundidad en el pasado. La predicción en dos etapas proporciona una solución adecuada al problema de sincronización de trayectorias aire-tierra dado que permite la sincronización de las dimensiones controladas por el sistema de guiado utilizando la información de la trayectoria de referencia proporcionada mediante FANS, y también facilita la mejora en la predicción de las dimensiones abiertas restantes usado un modelo del guiado que explota los modelos meteorológicos mejorados disponibles en tierra. Este proceso de predicción de la trayectoria de dos etapas se aplicó a una muestra de 438 vuelos reales que realizaron un descenso continuo (sin intervención del controlador) con destino Melbourne. Dichos vuelos son de aeronaves del modelo Boeing 737-800, si bien la metodología descrita es extrapolable a otros tipos de aeronave. El método propuesto de predicción de trayectorias permite una mejora en la desviación estándar del error de la estimación del tiempo de llegada al punto de interés, que es un 30% menor que la que obtiene el FMS. Dicha trayectoria prevista mejorada se puede utilizar para establecer la secuencia de arribadas y para la asignación de las franjas horarias para cada aterrizaje (slots). Sobre la base del slot asignado, se determina un perfil de velocidades que permita cumplir con dicho slot con un impacto mínimo en la eficiencia del vuelo. En la tesis se propone un nuevo algoritmo que determina las velocidades requeridas sin necesidad de un proceso iterativo de búsqueda sobre el sistema de predicción de trayectorias. El algoritmo se basa en una parametrización inteligente del proceso de predicción de la trayectoria, que permite relacionar el tiempo estimado de llegada con una función polinómica. Resolviendo dicho polinomio para el tiempo de llegada deseado, se obtiene de forma natural el perfil de velocidades optimo para cumplir con dicho tiempo de llegada sin comprometer la eficiencia. El diseño de los sistemas de gestión de arribadas propuesto en esta tesis aprovecha la aviónica y los sistemas de comunicación instalados de un modo mucho más eficiente, proporcionando valor añadido para la industria. Por tanto, la solución es compatible con la transición hacia los sistemas de aviónica avanzados que están desarrollándose actualmente. Los beneficios que se obtengan a lo largo de dicha transición son un incentivo para inversiones subsiguientes en la aviónica y en los sistemas de control de tráfico en tierra. ABSTRACT Air traffic management (ATM) is undergoing a paradigm shift towards trajectory based operations where the role of an air traffic controller evolves from that of continuous intervention towards supervision, as decision making is improved based on increased confidence in the solutions provided by advanced automation. To support this concept, significant investment for the development and acquisition of new equipment is required on the ground as well as in the air, to facilitate the high degree of trajectory synchronisation and information exchange required. Over the past 30-40 years the airline industry has generated one of the lowest returns on invested capital among all industries. Without tangible benefits realised, the airline industry may find it difficult to attract the required investment capital and delay acquiring equipment needed to realise the concept of trajectory based operations. In response to these challenges facing the modernisation of ATM, this thesis aims to answer the question whether existing aircraft capabilities can be applied to achieve sufficient trajectory synchronisation and improvements to ground-based trajectory prediction in support of the arrival management process, to realise some of the benefits envisioned under trajectory based operations, and to provide an incentive for further avionics upgrades. The proposed operational concept aims to permit aircraft to operate in a manner consistent with current optimal aircraft operating techniques. It allows aircraft to descend in the fuel efficient path managed mode as preferred by a majority of airlines, with arrival time not actively controlled by the airborne automation. The temporal uncertainty is managed through metering at strategically chosen points along the aircraft’s trajectory with primary use of speed advisories. While the focus is on speed advisories to support all aircraft and different levels of equipage, the concept also constitutes a framework in which advanced avionics as airborne time-of-arrival control can be integrated once this technology is widely available. In addition to managing temporal uncertainty through metering at multiple points, this temporal uncertainty is minimised by improving the supporting trajectory prediction capability. A novel two-stage trajectory prediction process is presented to adequately integrate aircraft trajectory data available through Future Air Navigation Systems (FANS) into the ground-based trajectory predictor. FANS is standard equipment on any wide-body aircraft in production today, and some single-aisle aircraft are easily capable of being fitted with FANS. In addition to automatic position reporting, FANS provides the ability to provide (part of) the reference trajectory held by the aircraft’s Flight Management System (FMS), but this capability has yet been widely overlooked. The two-stage process provides a ‘best of both world’s’ solution to the air-ground synchronisation problem by synchronising with the FMS reference trajectory those dimensions controlled by the guidance mode, and improving on the prediction of the remaining open dimensions by exploiting the high resolution meteorological forecast available to a ground-based system. The two-stage trajectory prediction process was applied to a sample of 438 FANS-equipped Boeing 737-800 flights into Melbourne conducting a continuous descent free from ATC intervention, and can be extrapolated to other types of aircraft. Trajectories predicted through the two-stage approach provided estimated time of arrivals with a 30% reduction in standard deviation of the error compared to estimated time of arrival calculated by the FMS. This improved predicted trajectory can subsequently be used to set the sequence and allocate landing slots. Based on the allocated landing slot, the proposed system calculates a speed schedule for the aircraft to meet this landing slot at minimal flight efficiency impact. A novel algorithm is presented that determines this speed schedule without requiring an iterative process in which multiple calls to a trajectory predictor need to be made. The algorithm is based on parameterisation of the trajectory prediction process, allowing the estimate time of arrival to be represented by a polynomial function of the speed schedule, providing an analytical solution to the speed schedule required to meet a set arrival time. The arrival management solution proposed in this thesis leverages the use of existing avionics and communications systems resulting in new value for industry for current investment. The solution therefore supports a transition concept from mixed equipage towards advanced avionics currently under development. Benefits realised under this transition may provide an incentive for ongoing investment in avionics.

Development of a method of assessment of the problem-solving competency at the Technical University of Madrid

The competence evaluation promoted by the European High Education Area entails a very important methodological change that requires guiding support to help lecturers carry out this new and complex task. In this regard, the Technical University of Madrid (UPM, by its Spanish acronym) has financed a series of coordinated projects with the objective of developing a model for teaching and evaluating core competences and providing support to lecturers. This paper deals with the problem solving competence. The first step has been to elaborate a guide for teachers to provide an homogeneous way to asses this competence. This guide considers several levels of acquisition of the competence and provided the rubrics to be applied for each one. The guide has been subsequently validated with several pilot experiences. In this paper we will explain the problem-solving assessment guide for teachers and will show the pilot experiences that has been carried out. We will finally justify the validity of the method to assess the problem solving competence.

Evolution over time of heavy vehicle volume in toll roads: A dynamic panel data to identify key explanatory variables in Spain

Improving the knowledge of demand evolution over time is a key aspect in the evaluation of transport policies and in forecasting future investment needs. It becomes even more critical for the case of toll roads, which in recent decades has become an increasingly common device to fund road projects. However, literature regarding demand elasticity estimates in toll roads is sparse and leaves some important aspects to be analyzed in greater detail. In particular, previous research on traffic analysis does not often disaggregate heavy vehicle demand from the total volume, so that the specific behavioral patternsof this traffic segment are not taken into account. Furthermore, GDP is the main socioeconomic variable most commonly chosen to explain road freight traffic growth over time. This paper seeks to determine the variables that better explain the evolution of heavy vehicle demand in toll roads over time. To that end, we present a dynamic panel data methodology aimed at identifying the key socioeconomic variables that explain the behavior of road freight traffic throughout the years. The results show that, despite the usual practice, GDP may not constitute a suitable explanatory variable for heavy vehicle demand. Rather, considering only the GDP of those sectors with a high impact on transport demand, such as construction or industry, leads to more consistent results. The methodology is applied to Spanish toll roads for the 1990?2011 period. This is an interesting case in the international context, as road freight demand has experienced an even greater reduction in Spain than elsewhere, since the beginning of the economic crisis in 2008.

Identification of the method to quantify soluble fibre and the effect of the source of fibre on the ileal and faecal digestibility of soluble and insoluble fibre in rabbits = Identificación del método para cuantificar la fibra soluble y el efecto de la fuente de fibra en la digestibilidad ileal y fecal de la fibra soluble e insoluble en conejos

La presente tesis constituye un avance en el estudio de los métodos para cuantificar la fibra soluble y los efectos de las fracciones de fibra y las fuentes de fibra sobre la digestión de las diferentes fracciones de fibra (soluble e insoluble) en el conejo. Hay un efecto positivo de la fibra soluble sobre la salud intestinal de los conejos y, por ende, una reducción de la mortalidad en animales destetados. Pese a esto, no está claro si estos efectos se deben específicamente a la fracción soluble. Por lo que los objetivos generales de esta tesis fueron: 1) comparar diferentes metodologías químicas e in vitro para cuantificar la fibra soluble y estudiar las posibles interferencias en la cuantificación de la fibra soluble por las mucinas, y viceversa, 2) determinar los efectos de la fibra, el lugar de fermentación, el método para valorar la fibra soluble e insoluble, y la corrección de la fibra soluble por el contenido intestinal de mucinas sobre la digestibilidad de las distintas fracciones de la fibra y 3) evaluar los efectos individuales de las fracciones soluble e insoluble de la fibra de pulpa de remolacha y de manzana, sobre la digestibilidad de la fibra soluble e insoluble y los parámetros digestivos. Para ello se llevaron a cabo 4 estudios. En el primer estudio se compararon diferentes metodologías químicas e in vitro para valorar la fibra soluble de diferentes alimentos y se estudió la posible interferencia en la determinación de la fibra soluble y mucinas. Para ello se utilizaron seis ingredientes (pulpa de remolacha, pectinas de pulpa de remolacha, pulpa de remolacha lavada, paja de cereal, cascarilla de girasol y lignocelulosa) y siete piensos de conejos con diferentes niveles de fibra soluble. En un primer experimento se analizó la fibra dietética total (FDT), la fibra dietética insoluble (FDI), la fibra dietética soluble (FDS), la fibra neutro detergente corregida por cenizas y proteínas (aFNDmo-pb), y la digestibilidad in vitro 2 pasos pepsina/pancreatina (residuo corregido por cenizas y proteína, ivMSi2) de los ingredientes y piensos. Además la fibra soluble se calculó mediante la diferencia entre FDT-FDI (FDSFDI), FDT- ivMSi2 (FDSivMSi2), y FDT - aFNDmo-pb (FDSaFNDmo-pb). Cuando la fibra soluble se determinó directamente como FDS o se calculó como FDT-FDI no se observaron diferencias (109 g/kg MS, en promedio). Sin embargo, cuando la fibra soluble se calculó como FDT - aFNDmo-pb su valor fue un 40% menor (153 g/kg MS. P < 0,05), mientras que la FDSFDI (124 g/kg MS) no fue diferente a ninguna de las otras metodologías. La correlación entre los tres métodos fue elevada (r > 0,96. P < 0,001. n = 13), pero disminuyó o incluso desapareció cuando la pulpa o las pectinas de la remolacha fueron excluidas del análisis. En un segundo experimento, se comparó el método ivDMi2 usando crisoles (método de referencia) con una modificación del mismo usando bolsas ANKOM digeridas individualmente o en colectivo para simplificar la determinación de la FDSivMSi2. La FDSivMSi2 no difirió entre los métodos comparados. En un tercer experimento, se analizó la posible interferencia entre la determinación de la fibra soluble y las mucinas intestinales. Se observó un contenido de FDT y de mucinas elevado en las muestras de pectinas de remolacha (994 y 709 g/kg MS), así como en el moco intestinal de conejo (571 y 739 g/kg MS) cuando se aplicó el método de mucinas por precipitación con etanol. Sin embargo, después de aplicar una pectinasa en el material precipitado, la cantidad de mucinas recuperadas en las muestras de pectinas de remolacha fue cercana a cero, mientras que en el moco intestinal fue similar a los resultados previos al uso de la enzima. Con los resultados de este ensayo se estimaron los carbohidratos de mucinas retenidos en los contenidos digestivos y se propuso una corrección para la determinación de la digestibilidad de la FDT y fibra soluble. En conclusión, la contaminación de las mucinas de la digesta con fibra soluble se soluciona usando pectinasas. El segundo estudio se centró en estudiar: 1) el efecto del tipo de fibra, 2) el sitio de fermentación, 3) el método para cuantificar fibra y 4) la corrección por mucinas sobre la digestibilidad de la fibra. Para ello se formularon tres piensos con diferentes niveles de fibra soluble (FDT-aFNDmo-pb). Un pienso bajo en fibra soluble (LSF. 85 g/kg DM), un pienso medio en fibra soluble (MSF. 102 g/kg DM), y un pienso alto en fibra soluble (HSF. 145 g/kg DM). Estos piensos se obtuvieron reemplazando un 50% del heno del alfalfa en el pienso MSF por una mezcla de pulpa de manzana y remolacha (HSF) o por una mezcla de cascarilla de avena y proteína de soja (LSF). Se utilizaron 30 conejas canuladas para determinar la digestibilidad ileal y fecal. La digestibilidad cecal se calculó mediante diferencia entre la digestibilidad fecal e ileal. La fibra insoluble se determinó como aFNDmo-pb, IDF, e ivMSi2, mientras que la fibra soluble se calculó como FDSFDI, FDSaFNDmo-pb, y FDSivMSi2. La digestibilidad de la FDT y la fibra soluble se corrigieron por las mucinas. La concentración de mucinas en la digesta ileal y fecal, aumento desde el grupo LSF hasta el grupo con el pienso HSF (P < 0,01). La corrección por mucinas aumentó las digestibilidades de la FDT y la fibra soluble a nivel ileal, mientras que a nivel cecal las redujo. (P < 0.01). El coeficiente de digestibilidad ileal de FDT aumentó desde el grupo LSF al grupo HSF (0,12 vs. 0,281. P < 0,01), sin diferencias en el coeficiente de digestibilidad cecal (0,264), por lo que la tendencia a nivel fecal entre los grupos se mantuvo. El coeficiente de digestibilidad ileal de la fibra insoluble aumento desde el grupo con el pienso LSF al grupo con el pienso HSF (0,113 vs. 0,210. P < 0,01), sin diferencias a nivel cecal (0,139) y sin efecto del método usado, resultando en una digestibilidad elevada a nivel fecal, con tendencias similares a las observadas a nivel ileal. El coeficiente de digestibilidad de la FND fue elevada en comparación con la FDI o la ivMSi2 (P > 0.01). El coeficiente de la digestibilidad ileal de la fibra soluble fue mayor en el grupo LSF respecto al grupo LSF (0,436 vs. 0,145. P < 0,01) y el método no afectó a esta determinación. El coeficiente de la digestibilidad cecal de la fibra soluble se redujo desde el grupo LSF hasta el grupo HSF (0,721 vs. 0,492. P < 0,05). El valor más bajo de digestibilidad cecal y fecal de fibra soluble fue medido con el método FDSaFNDmo-pb (P < 0,01). Se observó una alta correlación entre las digestibilidades de la fibra soluble determinada como FDSFDI, FDSaFNDmo-pb, y FDSivMSi2, por lo tanto la información proporcionada por una u otra metodología fueron similares. Sin embargo, cuando se compararon con efectos fisiológicos (producción de mucinas y peso del ciego y pH del ciego de un trabajo previo), la FDSaFNDmo-pb globalmente mostró estar mejor correlacionado con estos parámetros fisiológicos. En conclusión, la corrección por mucinas es necesaria para determinar la digestibilidad ileal de la FDT y fibra soluble, mientras que la elección de uno u otro método es menos relevante. La inclusión de pulpa de manzana y remolacha incrementa la cantidad de FDT que desaparece antes de llegar al ciego. En el tercer estudio se estudió el efecto de la fracción fibrosa soluble e insoluble de la pulpa de remolacha y el método de cuantificación de la fibra soluble e insoluble sobre la digestibilidad de la fibra y algunos parámetros digestivos. Para ello se formularon cuatro piensos con niveles similares de fibra insoluble (315g aFNDmo-pb/kg MS) y proteína (167 g/kg MS). El pienso control contuvo el nivel más bajo de fibra soluble (30,3 g/kg, con cascarilla de girasol y paja como fuente de fibra). Un segundo pienso se obtuvo mediante la sustitución de 60 g de almidón/kg del pienso control por pectinas de remolacha (82,9 g fibra soluble/kg MS). Los otras dos piensos resultaron de la sustitución parcial de las fuentes de fibra del pienso control por la fracción insoluble de la pulpa de remolacha y la pulpa de remolacha entera (42.2 y 82.3 g fibra soluble/kg MS, respectivamente). Cincuenta y seis conejos en cebo (14/pienso), de 2,4  0.21 kg de peso, fueron usados para determinar la digestibilidad ileal y fecal de la FDT, FDI, aFNDmo-pb, FDSFDI, y FDSaFNDmo-pb. La concentración de mucinas en el íleon y heces se utilizaron para corregir la digestibilidad de la FDT y fibra soluble. También se midió el peso de diferentes segmentos del tracto digestivo y el pH del contenido digestivo. Los conejos alimentados con el pienso de fibra insoluble de pulpa de remolacha mostraron los consumos más bajos con respecto a los demás grupos (124 vs. 139 g/d, respectivamente. P < 0,05). El flujo de mucinas ileales fue más alto (P < 0.05) en el grupo alimentado con el pienso de pectinas de remolacha (9,0 g/d en promedio) que los del grupo control (4,79 g/d), mostrando los otros dos grupos valores intermedios, sin detectarse diferencias a nivel fecal. La digestibilidad ileal de la FDT (corregida por mucinas) y la fibra insoluble no se vieron afectadas por el tipo de pienso. El método usado para determinar la fibra insoluble afectó su digestibilidad ileal (0,123 para FDI vs. 0,108 para aFNDmo-pb. P < 0.01). De todas formas, los métodos no afectaron al cálculo de la fibra fermentada antes del ciego (4,9 g/d en promedio). Los conejos alimentados con el pienso de pulpa de remolacha y con el pienso con la fracción insoluble de la pulpa de remolacha mostraron las digestibilidades fecales más altas de la fibra insoluble (0,266 en promedio vs. 0,106 del grupo control), mientras que en los animales del pienso con pectinas esta digestibilidad fue un 47% mayor respecto al pienso control (P < 0,001). La digestibilidad fecal de la fibra insoluble fue un 20% más alta cuando se usó la FND en lugar de FDI para determinarla (P < 0.001). Esto hizo variar la cantidad de fibra insoluble fermentada a lo largo del tracto digestivo (9,5 ó 7,5 g/d cuando fue calculada como FDI o aFNDmo-pb, respectivamente. P < 0,001). Las digestibilidades ileales de la fibra soluble fueron positivas cuando los análisis de fibra soluble de los contenidos ileales fueron corregidos por mucinas, (P < 0,001) excepto para la digestibilidad ileal de la FDSIDF del grupo control. Una vez corregidas por mucinas, los conejos alimentados con los piensos que contuvieron la fracción soluble de la pulpa de remolacha (pienso de pectina y pulpa de remolacha) mostraron una mayor digestibilidad ileal de la fibra soluble, respecto al grupo control (0,483 vs. -0,010. P = 0.002), mientras que el grupo del pienso de fibra insoluble de pulpa de remolacha mostró un valor intermedio (0,274). La digestibilidad total de la fibra soluble fue similar entre todos los grupos (0.93). Los conejos alimentados con pulpa de remolacha y su fracción insoluble mostraron los pesos relativos más altos del estómago respecto a los del pienso control y de pectinas (11 y 56 % respectivamente; P < 0,05). Por otra parte, el peso relativo del ciego aumentó en los animales que consumieron tanto la fracción soluble como insoluble de la pulpa de remolacha, siendo un 16% más pesados (P < 0,001) que el grupo control. El pH del contenido cecal fue más bajo en los animales del grupo de pulpa de remolacha que en los del grupo control (5,64 vs. 6,03; P < 0,001), mientras que los del grupo de pectinas y de fibra insoluble de pulpa de remolacha mostraron valores intermedios. En conclusión, el efecto positivo de la pulpa de remolacha en el flujo de mucinas a nivel ileal se debe a la fracción soluble e insoluble de la pulpa de remolacha. La mitad de la fibra soluble de la pulpa de remolacha desaparece antes de llegar al ciego, independientemente si esta proviene de pectinas puras o de la pulpa de remolacha. El pH cecal esta mejor correlacionado con la cantidad de FDT que desaparece antes del ciego más que con la que se degrada en el ciego. En el último estudio se estudiaron los efectos de la fibra soluble e insoluble de la pulpa de manzana sobre la digestibilidad de la fibra y algunos parámetros digestivos. Cuatro dietas fueron formuladas con niveles similares de fibra insoluble (aFNDmo-pb 32,4%) y proteína (18,6% ambos en base seca). El pienso control contuvo el nivel más bajo de fibra soluble (46 g de fibra soluble/kg, con cascarilla de girasol y paja de cereales como la fuentes de fibra). Un segundo pienso fue obtenido mediante la sustitución de 60 g de almidón/kg del pienso control por pectinas de manzana (105 g fibra soluble/kg). Los otros dos piensos se obtuvieron por la substitución de parte de las fuentes de fibra del pienso control por pulpa de manzana o pulpa de manzana despectinizada (93 y 71 g de fibra soluble/kg, respectivamente). La digestibilidad fecal fue determinada en 23 conejos/pienso con 1.68 ± 0.23 kg de peso vivo, los cuales fueron sacrificados a los 60 d edad para recolectar su contenido digestivo para determinar digestibilidad ileal y otros parámetros digestivos. La fibra soluble de manzana (pectinas y pulpa entera) estimuló el flujo ileal de mucinas (P = 0,002), pero no asi la pulpa despectinizada. La corrección por mucinas incrementó la digestibilidad de la FDT y la fibra soluble a nivel fecal, y especialmente a nivel ileal. Cerca de la mitad de la fibra soluble proveniente de los piensos con cualquiera de las fracciones de la pulpa de manzana fue degradada a nivel ileal, sin mostrar diferencias entre los grupos (46 y 86% en promedio a nivel ileal y fecal respectivamente). La inclusión de pulpa despectinizada de manzana mejoró la digestibilidad de la FND a nivel fecal (P < 0,05) pero no a nivel ileal. El contenido cecal de los conejos alimentados con la pulpa de manzana tuvieron el pH cecal más ácido que los del pienso control (5,55 vs. 5,95. P < 0,001), mientras que los animales con el pienso de pectinas de manzana y de pulpa de manzana despectinizada mostraron valores intermedios. En conclusión los efectos positivo de la pulpa de manzana en el flujo de mucinas se debió principalmente a la fracción soluble de la pulpa de manzana. La mitad de la fibra soluble fue degradada antes del ciego independientemente de si esta provino de las pectinas o de la pulpa de manzana. El pH cecal estuvo mejor correlacionado con la cantidad de FDT fermentada en todo el tracto digestivo y antes de llegar al ciego que con la que se degradó en el ciego. Al integrar los resultados de los estudio 2, 3 y 4 se concluyó que la corrección de mucinas de los contenidos digestivos al determinar FDT y fibra soluble es necesaria para ajustar los cálculos de su digestibilidad. Esta corrección es mucho más importante a nivel ileal y en dietas bajas en fibra soluble. Por otra parte, la FDT desapareció en proporciones importantes antes de llegar al ciego, especialmente en piensos que contienen pulpa de remolacha o de manzana o alguna fracción soluble o insoluble de las mismas y estas diferencias observadas entre los piensos a nivel ileal se correlacionaron mejor con el pH cecal, lo que indicaría que la FDT se solubilizó antes de llegar al ciego y una vez en esté fermentó. Estos resultados implican que determinar la fibra soluble como FDSaFNDmo-pb es la mejor opción y que en la determinación de la digestibilidad de la FDT y fibra soluble se debe considerar la corrección por mucinas especialmente a nivel ileal y en piensos bajos en fibra soluble. ABSTRACT The present thesis constitutes a step forward in advancing the knowledge of the methods to quantify soluble fibre and the effects of the fibre fractions and source of fibre on the site the digestion of different fractions of fibre (soluble and insoluble) in the rabbit. There is a positive effect of soluble fibre on rabbit digestive health and therefore on the reduction of mortality in weaning rabbits. Nevertheless, it is no so clear that the effects of soluble fibre on rabbits are due particularly to this fraction. This thesis aims: 1) to compare the quantification of soluble fibre in feeds using different chemical and in vitro approaches, and to study the potential interference between soluble fibre and mucin determinations, 2) to identify the effects of type of fibre, site of fermentation, method to quantify insoluble and soluble fibre, and correction of the intestinal soluble fibre content for intestinal mucin on the digestibility of fibre fractions and 3) to evaluate the individual effect of soluble and insoluble fibre from sugar beet pulp and apple pulp on ileal and faecal soluble and insoluble digestibility and digestive traits. These objectives were developed in four studies: The first study compared the quantification of soluble fibre in feeds using different chemical and in vitro approaches, and studied the potential interference between soluble fibre and mucin determinations. Six ingredients, sugar beet pulp (SBP), SBP pectins, insoluble SBP, wheat straw, sunflower hulls and lignocellulose, and seven rabbit diets, differing in soluble fibre content, were evaluated. In experiment 1, ingredients and diets were analysed for total dietary fibre (TDF), insoluble dietary fibre (IDF), soluble dietary fibre (SDF), aNDFom (corrected for protein, aNDFom-cp) and 2-step pepsin/pancreatin in vitro DM indigestibility (corrected for ash and protein, ivDMi2). Soluble fibre was estimated by difference using three procedures: TDF - IDF (SDFIDF), TDF - ivDMi2 (SDFivDMi2), and TDF - aNDFom-cp (SDFaNDFom-cp). Soluble fibre determined directly (SDF) or by difference, as SDFivDMi2 were not different (109 g/kg DM, on average). However, when it was calculated as SDFaNDFom-cp the value was 40% higher (153 g/kg DM, P < 0.05), whereas SDFIDF (124 g/kg DM) did not differ from any of the other methods. The correlation between the four methods was high (r ≥ 0.96. P ≤ 0.001. n = 13), but it decreased or even disappeared when SBP pectins and SBP were excluded and a lower and more narrow range of variation of soluble fibre was used. In experiment 2, the ivDMi2 using crucibles (reference method) were compared to those made using individual or collective ankom bags in order to simplify the determination of SDFivDMi2. The ivDMi2 was not different when using crucibles or individual or collective ankom bags. In experiment 3, the potential interference between soluble fibre and intestinal mucin determinations was studied using rabbit intestinal raw mucus, digesta and SBP pectins, lignocelluloses and a rabbit diet. An interference was observed between the determinations of soluble fibre and crude mucin, as the content of TDF and apparent crude mucin were high in SBP pectins (994 and 709 g/kg DM) and rabbit intestinal raw mucus (571 and 739 g/kg DM). After a pectinase treatment, the coefficient of apparent mucin recovery of SBP pectins was close to zero, whereas that of rabbit mucus was not modified. An estimation of the crude mucin carbohydrates retained in digesta TDF is proposed to correct TDF and soluble fibre digestibility. In conclusion, the values of soluble fibre depend on the methodology used. The contamination of crude mucin with soluble fibre is avoided using pectinase. The second study focused on the effect of type of fibre, site of fermentation, method for quantifying insoluble and soluble dietary fibre, and their correction for intestinal mucin on fibre digestibility. Three diets differing in soluble fibre were formulated (85 g/kg DM soluble fibre, in the low soluble fibre [LSF] diet; 102 g/kg DM in the medium soluble fibre [MSF] diet; and 145 g/kg DM in the high soluble fibre [HSF] diet). They were obtained by replacing half of the dehydrated alfalfa in the MSF diet with a mixture of beet and apple pulp (HSF diet) or with a mix of oat hulls and soybean protein (LSF diet). Thirty rabbits with ileal T-cannulas were used to determine total tract apparent digestibility (CTTAD) and ileal apparent digestibility (CIAD). Caecal digestibility was determined by difference between CTTAD and CIAD. Insoluble fibre was measured as aNDFom-cp, IDF, and ivDMi2, whereas soluble fibre was calculated as SDFaNDFom-cp, SDFIDF, SDFivDMi2. The intestinal mucin content was used to correct the TDF and soluble fibre digestibility. Ileal and faecal concentration of mucin increased from the LSF to the HSF diet group (P < 0.01). Once corrected for intestinal mucin, The CTTAD and CIAD of TDF and soluble fibre increased whereas caecal digestibility decreased (P < 0.01). The CIAD of TDF increased from the LSF to the HSF diet group (0.12 vs. 0.281. P < 0.01), with no difference in the caecal digestibility (0.264), resulting in a higher CTTAD from the LSF to the HSF diet group (P < 0.01). The CIAD of insoluble fibre increased from the LSF to the HSF diet group (0.113 vs. 0.21. P < 0.01), with no difference in the caecal digestibility (0.139) and no effect of fibre method, resulting in a higher CTTAD for rabbits fed the HSF diet compared with the MSF and LSF diets groups (P < 0.01). The CTTAD of aNDFom-cp was higher compared with IDF or ivDMi2 (P < 0.01). The CIAD of soluble fibre was higher for the HSF than for the LSF diet group (0.436 vs. 0.145. P < 0.01) and fibre method did not affect it. Caecal soluble fibre digestibility decreased from the LSF to the HSF diet group (0.721 vs. 0.492. P < 0.05). The lowest caecal and faecal soluble fibre digestibility was measured using SDFaNDFom-cp (P < 0.01). There was a high correlation among the digestibilities of soluble fibre measured as SDFaNDFom-cp, SDFIDF, and SDFivDMi2. Therefore, these methodologies provide similar information. However, the method that seems to be globally better related to the physiological traits (ileal flow of mucins, and relative weight of the caecum and caecal pH from previous work) was the SDFaNDFom-cp. In conclusion, a correction for intestinal mucin is necessary for ileal TDF and soluble fibre digestibility whereas the selection of the fibre method has a minor relevance. The inclusion of sugar beet and apple pulp increased the amount of TDF fermented in the small intestine. The third study examined the effect of fibre fractions of sugar beet pulp (SBP) and the method for quantifying soluble and insoluble fibre on soluble and insoluble fibre digestibility and digestive traits. Four diets were formulated with similar level of insoluble fibre (aNDFom-cp: 315 g/kg DM) and protein (167 g/kg DM). Control diet contained the lowest level of soluble fibre (30.3 g/kg DM, including sunflower hulls and straw as sole sources of fibre). A second diet was obtained by replacing 60 g starch/kg of control diet with SBP pectins (82.9 g soluble fibre/kg DM). Two more diets were obtained by replacing part of the fibrous sources of the control diet with either insoluble SBP fibre or SBP (42.2 and 82.3 g soluble fibre/kg DM, respectively). Fifty six (14/diet) rabbits weighing 2.40  0.213 kg were used to determine faecal and ileal digestibility of total dietary fibre (TDF), insoluble dietary fibre (IDF), neutral detergent fibre corrected for ash and CP (aNDFom-cp) and soluble fibre estimated as SDFaNDFom-cp and SDFIDF. Faecal and ileal mucin content was used to correct TDF and soluble fibre digestibility. It was also recorded weight of digestive segments and digesta pH. Rabbits fed insoluble SBP showed the lowest feed intake with respect to the other 3 diets (124 vs. 139 g/d, respectively. P < 0.05). Ileal mucin flow was higher (P < 0.05) in animals fed pectin and SBP diets (9.0 g/d, as average) than those fed control diet (4.79 g/d), showing InsSBP group an intermediate value. No differences on mucin content were detected at faecal level. There was no diet effect on the CIAD of TDF (corrected for mucin) and insoluble fibre. Fibre methodology influenced the CIAD of insoluble fibre (0.123 for IDF vs. 0.108 for aNDFom-cp. P < 0.01). Anyway, the amount of insoluble fibre fermented before the caecum did not differ between both methods (4.9 g/d, on average). Rabbits fed insoluble SBP and SBP diets showed the highest CTTAD of insoluble fibre (0.266 on average vs. 0.106 for control group), whereas those fed pectin diet had an intermediate value (0.106. P < 0.001). The CTTAD of insoluble fibre measured with IDF was higher than that measured with aNDFom-cp (by 20%. P < 0.001). It led that the amount of insoluble fibre fermented along the digestive tract were different (9.5 or 7.5 g/d when calculated as IDF or aNDFom-cp, respectively; P < 0.001). When the CIAD of soluble fibre was corrected for mucin they became positive (P < 0.001) except for control group measured as SDFIDF. Once corrected for mucin content, rabbits fed soluble fibre from SBP (pectin and SBP groups) showed higher CIAD of soluble fibre than control group (0.483 vs. -0.019. respectively), whereas the value for insoluble SBP group was intermediate 0.274. The CTTAD of soluble fibre (mucin corrected) was similar among diets 0.93. Rabbits fed with SBP and insoluble SBP diets showed higher total digestive tract and stomach relative weight than those fed pectin and control diets (by 11 and 56 %. respectively, P < 0.05). The caecal relative weight did not differ in rabbits fed pectin, insoluble SBP, and SBP diets (62 g/kg BW, as average) and they were on average 16% higher (P < 0.001) than in control group. Caecal content of rabbits fed SBP diet was more acid than those fed control diet (5.64 vs. 6.03. P < 0.001), whereas those from pectin and insoluble SBP diets showed intermediate values. In conclusion, the positive effect of SBP fibre on ileal mucin flow was due to both its soluble and insoluble fibre fraction. Half of the soluble SBP fibre was degraded before the caecum independently it came from pectin or SBP. The caecal pH correlated better with the ileal amount of fermented TDF in the digestive tract rather than with that fermented in the caecum. The last study examined the effect of soluble and insoluble fibre of apple pulp on fibre digestibility and digestive traits. Four diets were formulated with similar level of insoluble fibre (aNDFom-cp: 324 g/kg DM) and protein (18.6 g/kg DM). Control diet contained the lowest level of soluble fibre (46 g soluble fibre/kg DM, including oat hulls and straw as sole sources of fibre). A second diet was obtained by replacing 60 g starch/kg of control diet with apple pectins (105 g soluble fibre/kg DM). Two more diets were obtained by substituting part of the fibrous sources of the control diet by either apple pulp or depectinized apple pulp (93 and 71 g soluble fibre/kg, respectively). The CTTAD was determined in 23 rabbits/diet weighing 1.68  0.23 kg BW, and 23 rabbits/diet were slaughtered at 60 d of age to collect ileal digesta to determine CIAD and record other digestive traits. Soluble fibre from apple stimulated ileal flow of mucin (P = 0.002), but depectinized apple pulp did not. The correction for mucin increased the digestibility of crude protein, total dietary fibre, and soluble fibre at faecal, but especially at ileal level, depending in this case on the diet. Around half of the soluble fibre in diets containing any fibre fraction from apple was degraded at ileal level, with no differences among these diets (0.46 vs. 0.066 for control group, P=0.046). Faecal soluble fibre digestibility was 0.86 on average for all groups). Inclusion of the apple insoluble fibre improved NDF digestibility at faecal (0.222 vs. 0.069. P < 0.05) but not at ileal level. Caecal content of rabbits fed apple pulp diet was more acid than those fed control diet (5.55 vs. 5.95. P < 0.001), whereas those from pectin and depectinised apple pulp diets showed intermediate values. In conclusion, the positive effect of apple fibre on ileal mucin flow was mainly due to its soluble fibre fraction. Half of the soluble apple fibre was degraded before the caecum independently it came from pectin or apple pulp. The caecal pH correlated better with the total and ileal amount of fermented TDF in the digestive tract rather than with that fermented in the caecum. The results obtained in the studies 2, 3 and 4 were considered together. These results showed that the mucin correction is necessary when the TDF and soluble fibre digestibility is determined, and it correction is more important at ileal level and in diets with low level of soluble fibre. On another hand, incrementing the soluble fibre using sugar beet and apple pulp increased the amount of TDF disappear before the caecum. Moreover, the caecal pH correlated better with the ileal amount of fermented TDF in the digestive tract rather than with that fermented in the caecum. This suggests that an ileal fibre solubilisation may occur rather than ileal fermentation. Therefore the implications of this work were that: the estimation of soluble fibre as SDFaNDFom-cp is an adequate method considering its correlation with the physiological effects; and the TDF and soluble fibre digestibility must be corrected with intestinal mucins, especially when the ileal digestibility is determined.