Steel profiles for repairing deteriorated timber beam ends

Se describe un procedimiento para la consolidación de viguetas de forjado de madera con deterioro en las cabezas mediante perfiles de acero conectados a la madera desde la cara superior del forjado. La pieza de refuerzo es un perfil en U de acero S275 conformado en frío con pletinas soldadas insertadas en la madera y conectada mediante tirafondos. Se ensayaron 30 piezas a flexión obteniendo la rigidez y la capacidad de carga. Las probetas se dividieron en tres grupos. El primero compuesto por 10 piezas de madera laminada encolada de abeto con una sección de 180 x 200 mm y una longitud de 4.000 mm; el segundo consistía en 10 piezas de madera aserrada de pino silvestre con la misma sección y longitud y, el tercero, estaba formado por otras 10 piezas de madera del género Pinus con una sección de 130 x 150 mm y 3.000 mm de longitud, procedentes de un edificio de Madrid con 120 años de antigüedad. Cada grupo de 10 piezas se dividió a su vez en dos grupos de 5 piezas. El primer subgrupo estaba formado por las piezas completas de madera y constituía el grupo de referencia. Las piezas del segundo subgrupo tenían una longitud inferior que se salvaba con una extensión del refuerzo metálico. Los resultados indican que el sistema de refuerzo metálico permite resolver los problemas de falta de apoyo de la vigueta por deterioro de la madera que afecte en una longitud limitada (aproximadamente entre el 10 y el 20% de la longitud).

Prediction of bendig load capacity of timber beams by finite element method simulation of knots and grain deviation

A finite element model was used to simulate timberbeams with defects and predict their maximum load in bending. Taking into account the elastoplastic constitutive law of timber, the prediction of fracture load gives information about the mechanisms of timber failure, particularly with regard to the influence of knots, and their local graindeviation, on the fracture. A finite element model was constructed using the ANSYS element Plane42 in a plane stress 2D-analysis, which equates thickness to the width of the section to create a mesh which is as uniform as possible. Three sub-models reproduced the bending test according to UNE EN 408: i) timber with holes caused by knots; ii) timber with adherent knots which have structural continuity with the rest of the beam material; iii) timber with knots but with only partial contact between knot and beam which was artificially simulated by means of contact springs between the two materials. The model was validated using ten 45 × 145 × 3000 mm beams of Pinus sylvestris L. which presented knots and graindeviation. The fracture stress data obtained was compared with the results of numerical simulations, resulting in an adjustment error less of than 9.7%

Bonding shear strength in timber and GFRP glued with epoxy adhesives

The bonding quality of epoxy glued timber and glass fibre reinforced polymers (GFRP) was evaluated by means of compression loading shear test. Three timber species (Radiata pine, Laricio pine and Oak) and two kinds of GFRP (plates and rods made with polyester resin reinforced with mat and roving glass fibre) were glued and tested using three epoxy formulations. The increase in shear strength with age after the setting of epoxy formulations and the effect of surface roughness on timber and GRP gluing (the planing of the surface of timber and the previous sanding of GRP) were studied. It can be concluded that the mechanical properties of these products make them suitable for use in the reinforcement of deteriorated timber structures, and that a rough timber surface is preferable to a planed one, while the previous sanding of GRP surfaces is not advantageous.

Evaluation of the influence of visual parameters on wave transmission velocity in sawn chestnut timber

Non-destructive, visual evaluation and mechanical testing techniques were used to assess the structural properties of 374 samples of chestnut (Castanea sativa). The principal components method was applied to establish and interpret correlations between variables obtained of modulus of elasticity, bending strength and density. The static modulus of elasticity presented higher correlation values than those obtained using non-destructive methods. Bending strength presented low correlations with the non-destructive parameters, but there was some relation to the different knot ratios defined. The relationship was stronger with the most widely used ratio, CKDR. No significant correlations were observed between any of the variables and density.

Análisis comparativo de procedimientos para la medición de las gemas y evaluación de su influencia en la determinación de las propiedades mecánicas de la madera de Pinus sylvestris L. de gran escuadría. Comparison of wanes measurement systems to evaluate their influence on the mechanical properties of large cross section timber of Pinus sylvestris L.

Las gemas se evalúan mediante la norma de clasificación visual (UNE 56544), pero su aplicación en estructuras existentes y grandes escuadrías resulta poco eficaz y conduce a estimaciones demasiado conservadoras. Este trabajo analiza la influencia de las gemas comparando la resistencia de piezas con gemas y piezas correctamente escuadradas. Se han analizado 218 piezas de pino silvestre con dimensiones nominales 150 x 200 x 4.200 mm, de las que 102 presentaban una gema completa a lo largo de toda su longitud y el resto estaban correctamente escuadradas. En las piezas con gema se ha medido la altura de la sección cada 30 cm (altura en cada cara y altura máxima). Para determinar la resistencia se han ensayado todas las piezas de acuerdo a la norma EN 408. Se ha comparado la resistencia obtenida para las piezas con gema, diferenciando si la gema se encuentra en el borde comprimido o en el borde traccionado, con las piezas escuadradas. Puede concluirse que la presencia de gemas disminuye la resistencia excepto si la gema se encuentra en el borde traccionado, en cuyo caso los resultados obtenidos han sido similares a los de las piezas escuadradas. The wanes on structural timber are evaluated according to the visual grading standard (UNE 56544), but its application on existing structures and large cross sections is ineffective and leads to conservative estimations. This paper analyzes the influence of the wanes by comparing the resistance of pieces with wanes and square pieces. 218 pieces of Scotch pine with nominal dimensions 150 x 200 x 4200 mm have been analyzed, 102 of them had a complete wane along its length and the rest were properly squared. The height of the cross section was measured every 30 cm (the height on each side and the maximum height) for the pieces with wane. The bending strength of all the pieces was obtained according to the EN 408 standard. The bending strength of the pieces with wane has been compared with the strength of the squared pieces, taking into account if the wane is positioned on the compressed edge or on the tensioned edge. It can be concluded that the bending strength of the pieces with wanes is lower than the one of squared pieces, except if the wanes are on the tensioned edge of the beam.

Visual grading of large cross section structural timber of Pinus sylvestris L. according to UNE 56544:2007 standard

Large cross section structural timber have been used in many structures over long periods of time and still make up an important part of the market due to its mechanical properties. Furthermore, it is frequent its employment in new construction site. It involves the need for a visual grading standard for timber used in construction according to the quality assessment. The material has to satisfy the requirements according to the currently regulations. UNE 56544 is the Spanish visual grading standard for coniferous structural timber. The 2007 version defined a new visual grade in the standard for large section termed Structural Large Timber (MEG). This research checks the new visual grading and consists of 116 structural size specimens of sawn coniferous timber of Scotch pine (Pinus sylvestris L.) from Segovia, Spain. The pieces had a cross section of 150 by 200 mm. They were visually graded according to UNE 56544:2007. Also, mechanical properties have been obtained according to standard EN 408. The results show very low output with an excessive percentage of rejected pieces (33%). The main reasons for the rejection of pieces are fissures and twist

The flexibility matrix o timber composite beams with a discrete connection system

This work presents a method for the analysis of timber composite beams which considers the slip in the connection system, based on assembling the flexibility matrix of the whole structure. This method is based on one proposed by Tommola and Jutila (2001). This paper extends the method to the case of a gap between two pieces with an arbitrary location at the first connector, which notably broadens its practical application. The addition of the gap makes it possible to model a cracked zone in concrete topping, as well as the case in which forming produces the gap. The consideration of induced stresses due to changes in temperature and moisture content is also described, while the concept of equivalent eccentricity is generalized. This method has important advantages in connection with the current European Standard EN 1995-1-1: 2004, as it is able to deal with any type of load, variable section, discrete and non-regular connection systems, a gap between the two pieces, and variations in temperature and moisture content. Although it could be applied to any structural system, it is specially suited for the case of simple supported and continuous beams. Working examples are presented at the end, showing that the arrangement of the connection notably modifies shear force distribution. A first interpretation of the results is made on the basis of the strut and tie theory. The examples prove that the use of EC-5 is unsafe when, as a rule of thumb, the strut or compression field between the support and the first connector is at an angle with the axis of the beam of less than 60º.

Theoretical and experimental structural studies of historical Latin-American laminated planked timber arches

This article describes a first group of theoretical and experimental works undertaken at the Polytechnic University of Madrid. One major purpose is to obtain a structural model for the assessment of historical Latin-American vertically laminated planked timber arches built by the Spanish, mainly in the XVII and XVIII centuries. Many of those constructions still stand and represent a notable historical heritage. Pedro Hurtado recently presented his Ph. D. thesis on historical and construction topics. A structural study was then undertaken. This step of the structural research focussed on static analysis, most especially the deformation in the connection system. This article describes part of this first structural research. Even though it is still at a basic level, it shows reasonable agreement with the experimental results. Further static analytical models are been now developed and implemented. The next stage will address the dynamic problem, even though improvements will be made also in the constitutive equations.

Analysis of the stress state of a halved and tabled traditional timber scarf joint with the Finite Element Method

The purpose of this study is to determine the stress distribution in the carpentry joint of halved and tabled scarf joint with the finite element method (FEM) and its comparison with the values obtained using the theory of Strength of Materials. The stress concentration areas where analyzed and the influence of mesh refinement was studied on the results in order to determine the mesh size that provides the stress values more consistent with the theory. In areas where stress concentration is lower, different mesh sizes show similar stress values. In areas where stress concentration occurs, the same values increase considerably with the refinement of the mesh. The results show a central symmetry of the isobar lines distribution where the centre of symmetry corresponds to the geometric centre of the joint. Comparison of normal stress levels obtained by the FEM and the classical theory shows small differences, except at points of stress concentration.

Experimental and numerical investigation of effect of sawn timber dimensions in ultrasonic velocity measurements of Spanish softwoods

Ultrasonic sound velocity measurements with hand-held equipment remain due to their simplicity among the most used methods for non-destructive grading of sawn woods, yet a dedicated normalization effort with respect to strength classes for Spanish species is still required. As part of an ongoing project with the aim of definition of standard testing methods, the effect of the dimensions of commonly tested Scots pine (Pinus sylvestris L.) timbers and equipment testing frequency on ultrasonic velocity were investigated. A dedicated full-wave finite-difference time-domain software allowed simulation of pulse propagation through timbers of representative length and section combinations. Sound velocity measurements vL were performed along the grain with the indirect method at 22 kHz and 45 kHz for grids of measurement points at specific distances. For sample sections larger than the cross-sectional wavelength ?RT, the simulated sound velocity vL converges to vL = (CL/?)0.5. For smaller square sections the sound velocity drops down to vL = (EL/?)0.5, where CL, EL and ? are the stiffness, E-modul and density, respectively. The experiments confirm a linear regression between time of flight and measurement distance even at less than two wavelength menor que2?L distance, the fitted sound speed values increased by 15% between the two tested frequencies.

Bending reinforcement of timber beams with composite carbon fiber and basalt fiber materials

En el presente trabajo se lleva a cabo un estudio basado en datos obtenidos experimentalmente mediante el ensayo a flexión de vigas de madera de pino silvestre reforzadas con materiales compuestos. Las fibras que componen los tejidos utilizados para la ejecución de los refuerzos son de basalto y de carbono. En el caso de los compuestos de fibra de basalto se aplican en distintos gramajes, y los de carbono en tejido unidireccional y bidireccional. El material compuesto se realizó in situ, simultáneamente a la ejecución del refuerzo. Se aplicaron en una y en dos capas, según el caso, y la forma de colocación fue en ?U?, adhiriéndose al canto inferior y a las caras laterales de la viga mediante resina o mortero epoxi. Se analiza el comportamiento de las vigas según las variables de refuerzo aplicadas y se comparan con los resultados de vigas ensayadas sin reforzar. Con este trabajo queda demostrado el buen funcionamiento del FRP de fibra de basalto aplicado en el refuerzo de vigas de madera y de los tejidos de carbono bidireccionales con respecto a los unidireccionales.

Study of the increase in bending stiffness on timber beams reinforced with composite materials

It is common to find structures that need to be reinforced due to deterioration or because the function of the building changes. The economic cost involved in these forms of interventions is considerable. Therefore, it is interesting to progress in the existing strengthening techniques and the study of new reinforcement systems. This paper analyses the behaviour of timber beams reinforced with carbon and basalt fiber composite materials. The main objective of this study is to test the stiffness increase produced by the carbon and basalt FRP on reinforced beams. The results show the stiffness increase produced by the different types of reinforcement.

Definición de un Modelo Edafogeomorfológico para la Identificación de Necesidades de Manejo y Recuperación de Suelos a Nivel Local. Caso Cuenca Cañada La Gorda, Machiques Colón, Estado Zulia, Venezuela.

El objetivo de este trabajo es generar un modelo Edafogeomorfológico útil en la identificación de necesidades de manejo de suelos, se realizó un estudio en el área de la cuenca Cañada La Gorda Machiques-Colón, estado Zulia, Venezuela, caracterizada por un clima tropical de condición subhúmeda, con duración del periodo de crecimiento (DPC) de 230 días, régimen de humedad Ustic y de temperatura Isohipertémico. Se empleó el enfoque de la ecuación factorial de formación de suelos para el análisis y descripción biofísica de los factores a lo largo de una carena. El relieve caracterizado a partir de fotografías aéreas, imágenes de satélites y de chequeos sistemático mediante transectos en el sentido del flujo del escurrimiento; la vegetación a través del uso de la tierra, la cobertura vegetal, la identificación de las especies dominantes a partir de sus nombres vernáculos y la definición de indicadores de vegetales (Iv). Los suelos fueron descritos y clasificados según la Taxonomía de suelos y valorados mediante el modelo paramétricode Riquier et al. (1970) para determinar el índice de productividad (Ip). Se caracterizaron dos paisajes gemorfológicos: Colinar (C) y Valle (V), seis posiciones geomorfológicas entre ambos paisajes definidas por la sucesión de relieves en el sentido de la pendiente: Tope de colina-loma (TC), mesa conservada (MC), vertientes de mesa alta (VA), media (VM), baja (VB) y valle intracolinar (VI); e igual número de perfiles de suelos representativos, los cuales mostraron edafogénesis muy avanzada con Ip inferiores a 8% en todas las posiciones, exceptuando la VB, con una productividad de 13%. El uso de la tierra es a base de pastoreo semi-intensivo de plantas forrajeras introducidas. Las formaciones vegetales predominante fueron los matorrales y arbustales dispersos, acompañados con restos de una selva tropófila fuertemente afectada por la extracción forestal y la conversión en áreas de pastoreo. Se identificaron 8 Iv, asociados fuertemente con condiciones de físicas e hidrológicas del suelo. El alto impacto de las actividades humanas sobre el suelo y vegetación, expresado a través de los procesos de erosión activa, la ausencia de áreas boscosas y la baja productividad de los sistemas de ganadería reportada para la zona, señalan la necesidad de reorientación del uso actual de la tierra, para lo cual se plantean alternativas como la incorporación de bosques protectores y sistemas agrosilvopastoriles In order to generate an Edaphogeomorphological model to be used for the identification of management requirements of soils, a study was carried out in the area of the Cañada La Gorda watershed, Machiques Colon, Zulia State with a tropical climate, subsumid conditions with a growing period of 230 days, an Ustic soil moisture and Isohypertermic regimes. The soils factorial equation approach was used for the analisis and description of the factors of soil formation throughout a soil catena. Relief was characterized through aerial photographs, satellite images and systematic checks of transects drawn in the sense of surface runoff and also taking into account geomorphological features. Vegetation cover and land use were described and vegetation components were indified by its local names to defined vegetations indicators (VI) for the local conditions. Soils were described and classified according to soil taxonomy and valued by means of a parametric model proposed by Riquier et al, (1970) for determining the productivity index (PI). Two geomorphological landscapes were defined: Hilly and Valley with six positions within the landscapes: hilltop (round or elongated), preserved tableland summit, slopes of high, medium and low tableland and valleys between hills. Representative soils of each position were studied showing a highly advanced degree of edaphogenesis with PI values below 8% in all positions except the valleys with a PI of 13%. Land use type is based on semi intensive pasturing of introduced forage species, with a vegetation of brushwood and scattered shrubs, with some trees relicts of woods affected by timber extraction and turn to grassland Eight VI were identified, highly associated to local physical and hidrological soil conditions. The enormous impact of human activity on soils and vegetation as shown by active erosion processes and absence of wooded areas and the low productivity of livestock systems reported for the area, indicates the necessity of a reorientation of the present land use introducing alternatives like the incorporation of protective woods and agrosilvopastoral management systems.

Bovedas Encamonadas: Origen, Evolucion, Geometria y Construccion entre los Siglos XVII y XVIII en el Virreinato de Perú

Desde la creación del Virreinato del Perú, en el siglo XVI, los arcos, bóvedas y cúpulas se acostumbraban a levantar con piedra y fábrica. Sin embargo estas tierras eran sacudidas periodicamente por terremotos, produciendo el colapso de la mayoría de estas edificaciones. Para el siglo XVII los alarifes ya habían experimentado diversas maneras de levantar bóvedas, sin haberse encontrado una respuesta razonable en términos de tiempo, economía y estabilidad frente a los sismos. En medio de este panorama se produjo la introducción de las bóvedas encamonadas a mediados del siglo XVII, consolidandose en el resto de la centuria hasta el punto de terminar convirtiéndose en un recurso tradicional y de estimada elaboración dentro de la arquitectura virreinal peruana. Las bóvedas encamonadas se realizaban con tablas de madera (camones) que se solapaban entre sí para formar arcos (cerchas), los cuales definían la forma que tendrían las bóvedas, y eran estabilizados lateralmente mediante correas. Sobre los arcos y correas se colocaba un cerramiento que podía ser un entablado, unos listones de madera o simplemente un tendido a base de cañas. En la mayoría de casos se finalizaba con un recubrimiento aislante de barro por el extradós y otro decorativo de yeso por el intradós. Precisamente estas bóvedas constituyen el objeto de la presente tesis, específicamente en su devenir histórico entre los siglos XVII y XVIII en el ámbito territorial del Virreinato del Perú, partiendo del examen de los tratados de arquitectura coetáneos y del estudio de las bóvedas de madera en España, para finalizar con el análisis de las características geométricas y constructivas que lograron definir en ellas los alarifes peruanos. Since the creation of the Viceroyalty of Peru, in the sixteenth century, arches, vaults and domes were accustomed to build with stone and masonry. However, these lands were periodically shaken by earthquakes, causing the collapse of most of these buildings. For the seventeenth century the master masons had already experienced several ways to build vaults, without having found a reasonable response in terms of time, economy and stability against earthquakes. Into this context the master carpenters introduced the wooden vaults since seventeenth century, and this constructive system was consolidated around the rest of the century to the end point of becoming a traditional and estimated resource of the Peruvian colonial architecture. The wooden vaults were made with timber planks (camones) that overlapped each other to form arches (cerchas), which defined the shape of the vaults, and were stabilized laterally by purlins. Above the arches and purlins placed planks, wooden strips or just cane. In most cases ended with a mud plaster insulating the extrados and a decorative gypsum plaster on the intrados. Precisely these vaults are the subject of this thesis, specifically in its historical way between the seventeenth and eighteenth centuries in the territory of the Viceroyalty of Peru. Since an examination of the architectural treatises and the Spanish wooden vaults, and concluding with the analysis of the geometric and constructive system that Peruvian builders were able to define on them.

Diagnóstico de la seguridad en los aprovechamientos forestales a partir de registros empresariales, bases de datos oficiales y muestreos de campo: propuestas de actuación

Desde 1995, el derecho internacional se ha integrado en el ordenamiento jurídico español en lo referente a seguridad y salud. Sin embargo, la situación de la seguridad en los aprovechamientos forestales no ha mejorado notablemente, puesto que se detectan frecuentes casos de personal trabajando sin equipo de protección e incumpliendo las instrucciones de trabajo seguro, y son abundantes las referencias a una elevada accidentalidad. Para evaluar estos aspectos, primeramente se han comparado y valorado los datos de accidentalidad de los taladores de una empresa de referencia con los de los sectores agrario y de la construcción a través de las estadísticas nacionales y con los datos depurados del sector forestal a partir de la base de datos de declaración electrónica de accidentes de la C.A. de Castilla y León. En segundo lugar, se han identificado las deficiencias en materia de prevención, diseñando para ello una encuesta que se ha llevado a cabo en 35 aprovechamientos de Castilla y León. Posteriormente, se ha verificado que la reducción de la accidentalidad en la empresa de referencia se debe a la aplicación del plan de prevención. Se han caracterizado los riesgos en los que habían incurrido los taladores y se han descrito las medidas adoptadas para la reducción de los accidentes en la empresa estudiada, lo que ha conducido a una serie de recomendaciones para reducir la accidentalidad. Por otro lado se han analizado las causas de los picos de accidentalidad detectados. Como conclusión, se puede reducir sensiblemente la accidentalidad sólo si la empresa integra la política de prevención como un objetivo más de la gestión empresarial, en todos los niveles de su organización, acompañando las herramientas técnicas con formación temprana y motivación adecuada. Palabras clave: aprovechamientos forestales, riesgos laborales, prevención, trabajador forestal, accidentalidad, incidencia, gravedad. From 1995, Spanish safety legislation has been adapted to the Internationa! framework. However, operationally the situation is not so good, at least in the wood harvesting activity. Some forest workers are still found not wearing the compulsory safety equipment, working without respecting safety rules and references to high accidents rates are frequent. To assess those aspects, firstly some comparisons have been made between the accident records in a reference company and the accident indexes at national and regional level for building and farming activities. Secondly, using a purpose-designed questionnaire applied to 35 logging worksites in Castilla y Leon Region, deficiencies in prevention have been identified. The relation between the accident reduction and the prevention methods used by the reference studied company has been confirmed. Also the main causes and peaks of the accidents have been analyzed. Finally, some recommendations to reduce the risk of accidents in harvesting operations are provided. The main conclusion confirms that the possibility of reducing the accident risk is conditioned to the commitment of all the staff of the timber harvesting company, at every level of responsibility, to search for excellence in safety as one more entrepreneurial goal. This fact should be accompanied by the staff early training and the adequate motivation means. Keywords: logging, labor risk, safety and health, prevention, logging workers, accident incidence, accident severity.