The effects of tantalum addition on the microtexture and mechanical behaviour of tungsten for ITER applications

Tungsten (W) and its alloys are very promising materials for producing plasma-facing components (PFCs) in the fusion power reactors of the near future, even as a structural part in them. However, whereas the properties of pure tungsten are suitable for a PFC, its structural applications are still limited due to its low toughness, ductile to brittle transition temperature and recrystallization behaviour. Therefore, many efforts have been made to improve its performance by alloying tungsten with other elements. Hence, in this investigation, the thermo-mechanical performance of two new tungsten-tantalum materials has been evaluated. Materials with We5wt.%Ta and We15wt.%Ta were processed by mechanical alloying (MA) and later consolidation by hot isostatic pressing (HIP), with distinct settings for each composition. Thus, it was possible to determine the relationship between the microstructure and the addition of Ta with the macroscopic mechanical properties. These were measured by means of hardness, flexural strength and fracture toughness, in the temperature range of 300e1473 K. The microstructure and the fracture surfaces features of the tested materials were analysed by Field Emission Scanning Electron Microscopy (FESEM).

Formation energy of vacancies in FeCr alloys: Dependence on Cr concentration

A modified version of the concentration-dependent model (CDM) potential (A. Caro et al., Phys. Rev. Lett. 95 (2005) 075702) [1] has been developed to study defects in Fe–Cr for different Crconcentrations. A comparison between this new potential and DFT results for a variety of point defect configurations is performed in order to test its reliability for radiation damage studies. The effect of Crconcentration on the vacancyformationenergy in Fe–Cr alloys is analyzed in detail. This study shows a linear dependence of the vacancyformationenergy on Crconcentration for values above 6% of Cr. However, the formationenergy deviates from the linear interpolation in the region below 6% Crconcentration. In order to understand this behavior, the influence of the relative positions between Cr atoms and vacant sites on the vacancyformationenergy has been studied.

Object Kinetic Monte Carlo calculations of irradiated Fe-Cr dilute alloys: The effect of the interaction radius between substitutional Cr and self-interstitial Fe

ObjectKineticMonteCarlo models allow for the study of the evolution of the damage created by irradiation to time scales that are comparable to those achieved experimentally. Therefore, the essential ObjectKineticMonteCarlo parameters can be validated through comparison with experiments. However, this validation is not trivial since a large number of parameters is necessary, including migration energies of point defects and their clusters, binding energies of point defects in clusters, as well as the interactionradii. This is particularly cumbersome when describing an alloy, such as the Fe–Cr system, which is of interest for fusion energy applications. In this work we describe an ObjectKineticMonteCarlo model for Fe–Cr alloys in the dilute limit. The parameters used in the model come either from density functional theory calculations or from empirical interatomic potentials. This model is used to reproduce isochronal resistivity recovery experiments of electron irradiateddiluteFe–Cr alloys performed by Abe and Kuramoto. The comparison between the calculated results and the experiments reveal that an important parameter is the capture radius between substitutionalCr and self-interstitialFe atoms. A parametric study is presented on the effect of the capture radius on the simulated recovery curves.

High-temperature mechanical properties of aluminium alloys reinforced with titanium diboride (TiB2) particles

The physical and mechanical properties of metal matrix composites were improved by the addition of reinforcements. The mechanical properties of particulate-reinforced metal-matrix composites based on aluminium alloys (6061 and 7015) at high temperatures were studied. Titanium diboride (TiB2) particles were used as the reinforcement. All the composites were produced by hot extrusion. The tensile properties and fracture characteristics of these materials were investigated at room temperature and at high temperatures to determine their ultimate strength and strain to failure. The fracture surface was analysed by scanning electron microscopy. TiB2 particles provide high stability of the aluminium alloys (6061 and 7015) in the fabrication process. An improvement in the mechanical behaviour was achieved by adding TiB2 particles as reinforcement in both the aluminium alloys. Adding TiB2 particles reduces the ductility of the aluminium alloys but does not change the microscopic mode of failure, and the fracture surface exhibits a ductile appearance with dimples formed by coalescence.

Interstitial defects stability in FeCr alloys vs Cr concentration

Finding adequate materials to withstand the demanding conditions in the future fusion and fission reactors is a real challenge in the development of these technologies. Structural materials need to sustain high irradiation doses and temperatures that will change the microstructure over time. A better understanding of the changes produced by the irradiation will allow for a better choice of materials, ensuring a safer and reliable future power plants. High-Cr ferritic/martensitic steels head the list of structural materials due to their high resistance to swelling and corrosion. However, it is well known that these alloys present a problem of embrittlement, which could be caused by the presence of defects created by irradiation as these defects act as obstacles for dislocation motion. Therefore, the mechanical response of these materials will depend on the type of defects created during irradiation. In this work, we address a study of the effect Cr concentration has on single interstitial defect formation energies in FeCr alloys.

Mechanical properties of tungsten alloys with Y2O3 and titanium additions

In this research the mechanical behaviour of pure tungsten (W) and its alloys (2 wt.% Ti–0.47 wt.% Y2O3 and 4 wt.% Ti–0.5 wt.% Y2O3) is compared. These tungsten alloys, have been obtained by powder metallurgy. The yield strength, fracture toughness and elastic modulus have been studied in the temperature interval of 25 °C to 1000 °C. The results have shown that the addition of Ti substantially improves the bending strength and toughness of W, but it also dramatically increases the DBTT. On the other hand, the addition of 0.5% Y2O3, is enough to improve noticeably the oxidation behaviour at the higher temperatures. The grain size, fractography and microstructure are studied in these materials. Titanium is a good grain growth inhibitor and effective precursor of liquid phase in HIP. The simultaneous presence of Y2O3 and Ti permits to obtain materials with low pores presence

Characterization of Amorphous Tantalum Oxide for Insulating Acoustic Mirrors

This work describes the assessment of the acoustic properties of sputtered tantalum oxide films intended as high impedance films for the acoustic isolation of bulk acoustic wave devices operating in the GHz frequency range. The films are grown by sputtering a metallic tantalum target under different oxygen and argon gas mixtures, total pressures, pulsed DC powers and substrate bias. The structural properties of the films are assessed through infrared absorption spectroscopy and X-ray diffraction measurements. Their acoustic impedance is obtained after estimating the mass density by X-ray reflectometry measurements and the longitudinal acoustic velocity by analyzing the longitudinal λ/2 resonance induced in a tantalum oxide film inserted between an acoustic reflector and an AlN-based resonator. A second measurement of the sound velocity is achieved through picosecond acoustic spectroscopy.

Influence of the Lubrication Conditions on the Surface Finish of Turned Aeronautical Aluminium Alloys. A preliminary Study

Nowadays, one of the main objectives that affects the development of any new product is the respect for the environment. Until the late 80's, the development and manufacture of the most of the product were aimed to achieve maximum quality in time and costs with environmental issues relegated to secondary importance. On the other hand, in the 90's, the pressure from factors such as markets, financial and legislative factors, led to environmental considerations being taken into account. In this context, the current aeronautical industry strategies are based on the search for economic, environmental and energy efficiency considerations for all the processes involved in the aircraft manufacturing.

Laser Shock Processing: An Emerging Technique for the Enhancement of Surface Properties and Fatigue Life of High Strength Metal Alloys

Profiting by the increasing availability of laser sources delivering intensities above 10 9 W/cm 2 with pulse energies in the range of several Joules and pulse widths in the range of nanoseconds, laser shock processing (LSP) is being consolidating as an effective technology for the improvement of surface mechanical and corrosion resistance properties of metals and is being developed as a practical process amenable to production engineering. The main acknowledged advantage of the laser shock processing technique consists on its capability of inducing a relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly, the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Following a short description of the theoretical/computational and experimental methods developed by the authors for the predictive assessment and experimental implementation of LSP treatments, experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (specifically steels and Al and Ti alloys) under different LSP irradiation conditions are presented

Flow and fracture behaviour of high performance alloys

Based on our needs, that is to say, through precise simulation of the impact phenomena that may occur inside a jet engine turbine with an explicit non-linear finite element code, four new material models are postulated. Each one of is calibrated for four high-performance alloys that can be encountered in a modern jet engine. A new uncoupled material model for high strain and ballistic is proposed. Based on a Johnson-Cook type model, the proposed formulation introduces the effect of the third deviatoric invariant by means of three different Lode angle dependent functions. The Lode dependent functions are added to both plasticity and failure models. The postulated model is calibrated for a 6061-T651 aluminium alloy with data taken from the literature. The fracture pattern predictability of the JCX material model is shown performing numerical simulations of various quasi-static and dynamic tests. As an extension of the above-mentioned model, a modification in the thermal softening behaviour due to phase transformation temperatures is developed (JCXt). Additionally, a Lode angle dependent flow stress is defined. Analysing the phase diagram and high temperature tests performed, phase transformation temperatures of the FV535 stainless steel are determined. The postulated material model constants for the FV535 stainless steel are calibrated. A coupled elastoplastic-damage material model for high strain and ballistic applications is presented (JCXd). A Lode angle dependent function is added to the equivalent plastic strain to failure definition of the Johnson-Cook failure criterion. The weakening in the elastic law and in the Johnson-Cook type constitutive relation implicitly introduces the Lode angle dependency in the elastoplastic behaviour. The material model is calibrated for precipitation hardened Inconel 718 nickel-base superalloy. The combination of a Lode angle dependent failure criterion with weakened constitutive equations is proven to predict fracture patterns of the mechanical tests performed and provide reliable results. A transversely isotropic material model for directionally solidified alloys is presented. The proposed yield function is based a single linear transformation of the stress tensor. The linear operator weighs the degree of anisotropy of the yield function. The elastic behaviour, as well as the hardening, are considered isotropic. To model the hardening, a Johnson-Cook type relation is adopted. A material vector is included in the model implementation. The failure is modelled with the Cockroft-Latham failure criterion. The material vector allows orienting the reference orientation in any other that the user may need. The model is calibrated for the MAR-M 247 directionally solidified nickel-base superalloy.

Simulación atomística de metales líquidos y aleaciones para reactores de fusión nuclear = Atomistic simulation of liquid metals and alloys for nuclear fusion reactors

La presente tesis comprende un estudio de metales líquidos, Li, Pb y eutéctico Li17Pb en el ámbito de la tecnología de fusión nuclear. Uno de los problemas fundamentales en futuros reactores de fusión es la producción y extracción de tritio en la denominada envoltura regeneradora (blanket en inglés). Dicho blanket tendrá dos propósitos, la extracción del calor generado por las reacciones de fusión para su posterior conversión en energía eléctrica así como la producción de tritio para realimentar el proceso. Dicha producción se realizará mediante el “splitting” del Li con los neutrones provenientes de la fusión. Esta reacción produce tritio y helio por lo que la interacción del T y el He con el metal líquido, con los materiales estructurales así como con el He es un problema fundamental aun no bien entendido y de gran importancia para futuros diseños. Los capítulos 1 2 y 3 presentan una introducción a dichos problemas. El capítulo 1 introduce al lector en la tecnología de fusión nuclear. El segundo capítulo explica en mayor detalle el uso de metales líquidos en reactores de fusión, no solo en blankets sino también como primera pared, divertor etc, lo que se denomina en general “plasma facing materials”. Por último se ofrece una breve introducción a las técnicas de dinámica molecular clásica (CMD) y un breve resumen de los potenciales más usados. El estudio se ha llevado a cabo utilizando simulación atomística mediante potenciales semi-empíricos del tipo átomo embebido (EAM). La Tesis consta de 4 partes bien definidas. En primer lugar se verificó la idoneidad de los potenciales tipo EAM para simular las propiedades de los metales Li y Pb en fase líquida. Dicho estudio se detalla en el Capítulo 4 y en su extensión, el Apéndice 1, en el que se estudia los límites de validez de esta aproximación. Los resultados de dicho estudio han sido publicados y presentados en diversos congresos internacionales. Un resumen de la metodología seguida fue publicado como capítulo de libro en Technofusión 2011. Los resultados se presentaron en diversos congresos internacionales, entre ellos ICENES 2011, (Artículo en ICENES Proceedings) ICOPS-SOFE 2011, en una presentación oral etc. El trabajo ha sido aceptado recientemente en Journal of Nuclear Materiales (Fraile et al 2012). La segunda parte y más importante comprende el desarrollo de un potencial para el estudio de la mezcla de ambos metales. Éste es el trabajo más novedoso e importante dado que no existía en la literatura un potencial semejante. Se estudiaron dos aproximaciones distintas al problema, un potencial tipo EAM/cd y un potencial EAM/alloy. Ambos potenciales dan resultados satisfactorios para la simulación del eutéctico (y concentraciones de Li menores que el 17%). Sin embargo el sistema LiPb en todas las concentraciones es un sistema que se aparta enormemente de una solución ideal y dicho potencial no daba buenos resultados para mezclas PbLi con concentraciones de Li grandes. Este problema fue solventado mediante el desarrollo de un segundo potencial, esta vez tipo EAM/alloy (segunda parte del Capítulo 5). Dicho trabajo será enviado a Physical Review Letters o a Phys. Rev. B, y una extensión junto con un estudio detallado de las propiedades del eutéctico de acuerdo con nuestras simulaciones se enviará a continuación a Phys. Rev. B. En tercer lugar se estudió el problema de la difusividad del H en metales líquidos aprovechando distintos potenciales existentes en la literatura. El problema del H en metales líquidos es importante en metalurgia. En dicho capítulo se estudió la difusividad del H en Pd, Ni y Al con potenciales tipo EAM, y también con un potencial más sofisticado que tiene en cuenta la dependencia angular de las interacciones (ADP por sus siglas en inglés). De este modo disponemos de un estudio detallado del problema con diferentes modelos y diferentes metales. La conclusión apunta a que si se compara con los resultados experimentales (muy escasos) los resultados obtenidos mediante CMD dan valores bajos de la difusividad del H. Las razones de dicho desacuerdo entre simulación y experimentos se detallan en el Capítulo 6. Este trabajo ha sido presentado en una presentación oral en el reciente congreso internacional “Trends on Nanothecnology” TNT 2012 celebrado en Madrid. El trabajo será publicado en un futuro próximo. Por último, como se dijo anteriormente, el estudio del He, la formación de burbujas en metales líquidos, su difusión nucleación y cavitación es otro problema deseable de ser estudiado mediante técnicas atomísticas. Para ello es necesario el desarrollo de diversos potenciales, He-Li, He-Pb y un potencial ternario Pb-Li-He. Para ello se han realizado simulación ab initio de los sistemas Pb+He y Li+He. Dicho estudio pretende calcular las fuerzas entre los átomos del metal (Pb o Li) con intersticiales de He. De este modo aplicaremos el “force matching method” (FMM) para el desarrollo de dichos potenciales. En el Capítulo 7 se detallan los resultados obtenidos referidos a las posiciones más favorables de las impurezas de He dentro de redes cristalinas de Pb y Li así como el efecto de tener en cuenta el acoplo spin-orbita (SOC en inglés). El análisis de los resultados en términos de transferencia de carga y análisis de las densidades electrónicas, así como la creación de los potenciales mencionados está en progreso. En conjunto la tesis presenta un estudio de los diversos problemas relacionados con el uso de metales líquidos en reactores de fusión y representa un primer paso en la determinación de parámetros de gran importancia para el diseño de blankets y sistemas de primera pared. Con la simulación MD de dichos problemas mediante, importante, potenciales realistas, valores de difusión, solubilidad etc de especies ligeras, H (o sus isotopos) y He en metales líquidos podrá ser calculada complementando así la base de datos que presenta enormes incertidumbres.

High-Acoustic-Impedance Tantalum Oxide Layers for Insulating Acoustic Reflectors

This work describes the assessment of the acoustic properties of sputtered tantalum oxide films intended for use as high-impedance films of acoustic reflectors for solidly mounted resonators operating in the gigahertz frequency range. The films are grown by sputtering a metallic tantalum target under different oxygen and argon gas mixtures, total pressures, pulsed dc powers, and substrate biases. The structural properties of the films are assessed through infrared absorption spectroscopy and X-ray diffraction measurements. Their acoustic impedance is assessed by deriving the mass density from X-ray reflectometry measurements and the acoustic velocity from picosecond acoustic spectroscopy and the analysis of the frequency response of the test resonators.

Determination of the magnetostrictive atomic enviroments in FeCoB alloys

The atomic environments of Fe and Co involved in the magnetostriction effect in FeCoB alloys have been identified by differential extended x-ray fine structure (DiffEXAFS) spectroscopy. The study, done in amorphous and polycrystalline FeCoB films, demonstrates that the alloys are heterogeneous and that boron plays a crucial role in the origin of their magnetostrictive properties. The analysis of DiffEXAFS in the polycrystalline and amorphous alloys indicates that boron activates magnetostriction when entering as an impurity into octahedral interstitial sites of the Fe bcc lattice, causing its tetragonal distortion. Magnetostriction would be explained then by the relative change in volume when the tetragonal axis of the site is reoriented under an externally applied magnetic field. The experiment demonstrates the extreme sensitivity of DiffEXAFS to characterize magnetostrictive environments that are undetectable in their related EXAFS spectra.

Stability of vacancy clusters in FeCr alloys: A study of the Cr concentration dependence

Fe–Cr based alloys are the leading structural material candidates in the design of next generation reactors due to their high resistance to swelling and corrosion. Despite these good properties there are others, such as embrittlement, which require a higher level of understanding in order to improve aspects such as safety or lifetime of the reactors. The addition of Cr improves the behavior of the steels under irradiation, but not in a monotonic way. Therefore, understanding the changes in the Fe–Cr based alloys microstructure induced by irradiation and the role played by the alloying element (Cr) is needed in order to predict the response of these materials under the extreme conditions they are going to support. In this work we perform a study of the effect of Cr concentration in a bcc Fe–Cr matrix on formation and binding energies of vacancy clusters up to 5 units. The dependence of the calculated formation and binding energy is investigated with two empirical interatomic potentials specially developed to study radiation damage in Fe–Cr alloys. Results are very similar for both potentials showing an increase of the defect stability with the cluster size and no real dependence on Cr concentration for the binding energy.

A comprehensive diagram to grow metal-polarity InGaN alloys by molecular beam epitaxy

he composition, strain and surface morphology of (0001)InGaN layers are investigated as a function of growth temperature (460–645 °C) and impinging In flux. Three different growth regimes: nitrogen-rich, metal-rich and intermediate metal-rich, are clearly identified and found to be in correlation with surface morphology and strain relaxation. Best epilayers’ quality is obtained when growing under intermediate metal-rich conditions, with 1–2 monolayers thick In ad-coverage. For a given In flux, the In incorporation decreases with increasing growth temperature due to InN thermal decomposition that follows an Arrhenius behavior with 1.84±0.12 eV activation energy.