In situ surveillance of capacitive pressure transmitter dynamic poles

In this work, a methodology is proposed to find the dynamic poles of a capacitive pressure transmitter in order to enhance and extend the online surveillance of this type of sensor based on the response time measurement by applying noise analysis techniques and the dynamic data system procedure. Several measurements taken from a pressurized water reactor have been analyzed. The methodology proposes an autoregressive fit whose order is determined by the sensor dynamic poles. Nevertheless, the signals that have been analyzed could not be filtered properly in order to remove the plant noise; thus, this was considered as an additional pair of complex conjugate poles. With this methodology we have come up with the numerical value of the sensor second real pole in spite of its low influence on the sensor dynamic response. This opens up a more accurate online sensor surveillance since the previous methods were achieved by considering one real pole only.

AR modelling and DDS for in situ surveillance of capacitive pressure transmitters

In this work, a methodology is proposed to find the dynamics poles of a capacitive pressure transmitter in order to enhance and extend the on line surveillance of this type of sensors based on the response time measurement by applying noise analysis techniques and the Dynamic Data System. Several measurements have been analyzed taken from a Pressurized Water Reactor. The methodology proposes an autoregressive fit whose order is determined by the sensor dynamics poles. Nevertheless, the signals that have been analyzed, could not be filtered properly in order to remove the plant noise, thus, this was considered as an additional pair of complex conjugate poles. With this methodology we have come up with the numerical value of the sensor second real pole in spite of its low influence on the sensor dynamic response. This opens up a more accurate on line sensor surveillance since the previous methods were achieved by considering one real pole only.

Surveillance of habitats and plant diversity indicators across a regional gradient in the Iberian Peninsula

Dentro del Proyecto EBONE (Red de Observación de la Biodiversidad Europea) se analizan diferentes tipos de paisaje en varias zonas de Madrid y norte de Portugal. Se realiza un estudio de los habitats y la diversidad de especies con el objetivo principal de preservarlos y conservalos.

Influence of crowds in the dynamic characteristics of a structure

The interest for modelling of human actions acting on structures has been recurrent since the first accidents on suspension bridges in the nineteenth century like Broughton (1831) in the U.K. or Angers (1850) in France. Stadiums, gymnasiums are other type of structure where the human induced vibration is very important. In these structures appear particular phenomenon like the interaction person-structure (lock-in), the person-person synchronization, and the influence of the mass and damping of the people in the structure behaviour. This work focuses on the latter topic. The dynamic characteristic of a structure can be changed due to the presence of people on it. In order to evaluate these property modifications several testing have been carried out on a structure designed to be a gymnasium. For the test an electro-dynamic shaker was installed in a fixed point of the gym slab and different groups of people were located around the shaker. In each test the number of people was changed and also their posture (standing and sitting). Test data were analyzed and processed to verify modifications in the structure behaviour.

Detection and Tracking of Dynamic Objects. A MultiRobot approach to Critical Infrastructures Surveillance.

Despite that Critical Infrastructures (CIs) security and surveillance are a growing concern for many countries and companies, Multi Robot Systems (MRSs) have not been yet broadly used in this type of facilities. This dissertation presents a novel study of the challenges arisen by the implementation of this type of systems and proposes solutions to specific problems. First, a comprehensive analysis of different types of CIs has been carried out, emphasizing the influence of the different characteristics of the facilities in the design of a security and surveillance MRS. One of the most important needs for the surveillance of a CI is the detection of intruders. From a technical point of view this problem can be abstracted as equivalent to the Detection and Tracking of Mobile Objects (DATMO). This dissertation proposes algorithms to solve this specific problem in a CI environment. Using 3D range images of the environment as input data, two detection algorithms for ground robots have been developed. These detection algorithms provide a list of moving objects in the robot detection area. Direct image differentiation and computer vision techniques are used when the robot is static. Alternatively, multi-layer ground reconstructions are compared to detect the dynamic objects when the robot is moving. Since CIs usually spread over large areas, it is very useful to incorporate aerial vehicles in the surveillance MRS. Therefore, a moving object detection algorithm for aerial vehicles has been also developed. This algorithm compares the real optical flow obtained from a down-face oriented camera with an artificial optical flow computed using a RANSAC based homography matrix. Two tracking algorithms have been developed to follow the moving objects trajectories. These algorithms can efficiently handle occlusions and crossings, as well as exchange information among robots. The multirobot tracking can be applied to any type of communication structure: centralized, decentralized or a combination of both. Even more, the developed tracking algorithms are independent of the detection algorithms and could be potentially used with other detection procedures or even with static sensors, such as cameras. In addition, using the 3D point clouds available to the robots, a relative localization algorithm has been developed to improve the position estimation of a given robot with observations from other robots. All the developed algorithms have been extensively tested in different simulated CIs using the Webots robotics simulator. Furthermore, the algorithms have also been validated with real robots operating in real scenarios. In conclusion, this dissertation presents a multirobot approach to Critical Infrastructure Surveillance, mainly focusing on Detecting and Tracking Dynamic Objects.

Surveillance and diagnostics of the beam mode vibrations of the ringhals pwrs

Surveillance of core barrel vibrations has been performed in the Swedish Ringhals PWRs for several years. This surveillance is focused mainly on the pendular motion of the core barrel, which is known as the beam mode. The monitoring of the beam mode has suggested that its amplitude increases along the cycle and decreases after refuelling. In the last 5 years several measurements have been taken in order to understand this behaviour. Besides, a non-linear fitting procedure has been implemented in order to better distinguish the different components of vibration. By using this fitting procedure, two modes of vibration have been identified in the frequency range of the beam mode. Several results coming from the trend analysis performed during these years indicate that one of the modes is due to the core barrel motion itself and the other is due to the individual flow induced vibrations of the fuel elements. In this work, the latest results of this monitoring are presented.

Surveillance and diagnostics of the beam mode vibrations of the ringhlas PWRs

Surveillance of core barrel vibrations has been performed in the Swedish Ringhals PWRs for several years. This surveillance is focused mainly on the pendular motion of the core barrel, which is known as the beam mode. The monitoring of the beam mode has suggested that its amplitude increases along the cycle and decreases after refuelling. In the last 5 years several measurements have been taken in order to understand this behaviour. Besides, a non-linear fitting procedure has been implemented in order to better distinguish the different components of vibration. By using this fitting procedure, two modes of vibration have been identified in the frequency range of the beam mode. Several results coming from the trend analysis performed during these years indicate that one of the modes is due to the core barrel motion itself and the other is due to the individual flow induced vibrations of the fuel elements. In this work, the latest results of this monitoring are presented.

Experimentel ADS-B based surveillance

This paper describes an ADS-B implementation in air-to-air and ground based experimental surveillance within a prototype ATM system. The relations between airborne and ground systems related to surveillance are detailed, and the prototype surveillance systems and their algorithms described. Their performance is analysed, based both on simulated and real data.

Correction of systematic errors in Wide Area Multilateration

This work presents a method to estimate and correct slow time-dependent position errors due to non perfect ground station synchronization and tropospheric propagation. It uses opportunity traffic emissions, i.e. signals transmitted from the aircrafts within the coverage zone. This method is used to overcome the difficulty of installing reference beacons simultaneously visible by all the base stations in a given Wide Area Multilateration (WAM) system.

A Knowledge-based Approach for Automatic Generation of Summaries of Behavior

Effective automatic summarization usually requires simulating human reasoning such as abstraction or relevance reasoning. In this paper we describe a solution for this type of reasoning in the particular case of surveillance of the behavior of a dynamic system using sensor data. The paper first presents the approach describing the required type of knowledge with a possible representation. This includes knowledge about the system structure, behavior, interpretation and saliency. Then, the paper shows the inference algorithm to produce a summarization tree based on the exploitation of the physical characteristics of the system. The paper illustrates how the method is used in the context of automatic generation of summaries of behavior in an application for basin surveillance in the presence of river floods.

Fault detection and isolation on a noisy nonlinear circuit

In this paper fault detection and isolation (FDI) schemes are applied in the context of the surveillance of emerging faults in an electrical circuit. The FDI problem is studied on a noisy nonlinear circuit, where both abrupt and incipient faults in the voltage source are considered. A rigorous analysis of fault detectability precedes the application of the fault detection (FD) scheme; then, the fault isolation (FI) phase is accomplished with two alternative FI approaches, proposed as new extensions of that FD approach. Numerical simulations illustrate the applicability of the mentioned schemes.

Ensayos de seguridad eléctrica orientados a la vigilancia del mercado

El presente estudio recopila los diferentes bancos de pruebas de EMC, Radio, SAR y seguridad eléctrica que se utiliza en la vigilancia del mercado. Describe las pruebas realizadas por el Estado español para llevar a cabo el seguimiento y control de los equipos vendidos. En primer lugar se presenta una descripción cualitativa de los ambientes clasificados por requisitos que explica en qué consisten las pruebas que se hacen, cómo se configura el entorno de medida y cuáles son los equipos que se deben utilizar. Está ilustrado con fotografías de los bastidores, antenas, amplificadores, generadores y otros equipos que la SETSI tiene en su laboratorio en El Casar (Guadalajara). La vigilancia de los equipos se realiza periódicamente en los estados miembros de la Unión Europea. Los funcionarios responsables también se reúnen periódicamente a nivel europeo para sacar conclusiones y hacer proyecciones futuras. El equipo adquirido en centros comerciales de venta al público, después de poco más de un mes, en el que se pasan las pruebas, vuelve a la cadena de comercialización, por lo que los dispositivos no se puedan dañar. Las pruebas realizadas en el laboratorio no pueden ser perjudiciales para los dispositivos por lo que es necesario tomar precauciones en la ejecución de las pruebas. El centro del PFC es el área de la Seguridad Eléctrica. El capítulo 4 es una reproducción de la Norma internacional IEC 60950-1:2007/A11 sobre seguridad en equipos de tecnología de la información adaptada a los requisitos de la vigilancia de mercado. Las autoridades competentes se basan en este estándar para evaluar y garantizar la seguridad del usuario en los equipos de consumo. Diseñados los procedimientos de ensayo y montado un banco de acuerdo a estos ensayos, se ha preparado un manual de operador, capítulo 5, en el que se recogen cada una de las pruebas y controles visuales que deben realizarse para probar que el equipo es conforme. Para finalizar, en el capítulo 6, se ejecutan ensayos de ejemplo sobre tres dispositivos de prueba y se elaboran las correspondientes hojas de ensayo. El propósito es proporcionar al operador un manual completo del banco de seguridad eléctrica, es por ello que en el manual de operador se han repetido muchos fragmentos de la norma para facilitar al operador el objetivo concreto de las pruebas y el acceso fácil a la información. This dissertation presents the different test benches of EMC, Radio, SAR and Electrical Safety that are used in market surveillance. Describes the tests performed by the Spanish State to carry out the monitoring and control of equipment sold. First a qualitative description of the environments classified by requisites that explains in that consist the tests that are make it, how it configures the measure environment and which are the equipment that it should use. It is illustrated with photographs of the racks, antennas, amplifiers, generators and other equipment that the S.E.T.S.I has in its laboratory on El Casar (Guadalajara). The surveillance of equipment is performed periodically in the member states of the European Union. Responsible officials also periodically meet at European level to draw conclusions and make future projections. The equipment purchased in malls public sale, after little more than a month, in which the tests are passed, returned to the trade chain, which is why the devices cannot be damaged. The tests done in the laboratory may not be harmful for devices are thus necessary to take precautions in the execution of the tests. The center of this dissertation is the area of Electrical Safety. Chapter 4 is a reproduction of the International Standard IEC 60950-1:2007/A11 safety in teams of information technology, adapted to the requirements of market surveillance. The competent authorities are based on this standard to assess and ensure the user's safety in the consumption equipment. Designed test procedures and mounted on a bench according to these tests, it has prepared a manual operator, in Chapter 5, with each of the tests and visual inspections in order to prove that the equipment complies. Finally, in Chapter 6, such tests run on three devices are developed test and test some leaves. The purpose of this book is to provide an operator manual of the bench of electrical safety, which is why the operator manual have been repeated fragments of the standard, in chapter 5, to facilitate the operator to test execution and access to information.

Diseño de una estrategia para la definición de proyectos a partir de la vigilancia tecnológica: aplicación a las interfaces naturales

A la hora de afrontar un proyecto de investigación, no basta con una vigilancia tradicional del entorno. Ya que debido a lo cambiante del mundo, a la globalización, a lo rápido que se desarrollan nuevas tecnologías y productos es preciso realizar un proceso sistemático que permita a las organizaciones o empresas anticiparse a los cambios tecnológicos. En este contexto, el diseño de metodologías basadas en la Vigilancia Tecnológica (VT) permite gestionar la actividad innovadora de organizaciones o empresas facilitando el proceso de generación de ideas para el desarrollo de productos o servicios. Es por ello que en este Proyecto de Fin de Grado se ha diseñado una estrategia para aplicar metodologías de Vigilancia Tecnológica aplicadas a un proyecto de I+D que estudia las Interfaces Naturales de Usuario (NUI). Para ello se ha partido de la metodología de trabajo basada en el proceso de Vigilancia Tecnológica e Inteligencia Competitiva del proyecto CETISME, identificando claramente cada una de las fases que lo componen: identificación de objetivos, selección de las fuentes de información, búsqueda y almacenamiento de la información, análisis de la información y por último validación de la información que concluye con la creación de informes de Vigilancia Tecnológica. Por lo tanto, para cada una de las fases que componen lo que comúnmente se llama el ciclo de la vigilancia, se ha explicado en primer lugar en qué consisten, que estrategias a seguir son las más adecuadas así como la manera de llevarlas a cabo, y por último, si fuera necesario, qué herramientas (desde bases de datos a software) son necesarias o son de utilidad para llevar a cabo el proceso y optimizarlo. De esta manera, como se verá a lo largo de este documento, la aplicación de dicha metodología permitirá a las organizaciones o empresas obtener situaciones ventajosas a la hora de innovar, captar oportunidades o detectar amenazas, identificar competidores o alianzas potenciales, entre otros. ABSTRACT. When taking over a research project, a traditional surveillance of the environment is not enough. Mainly due to the changing the world, to the globalization, to how fast new technologies and products are developed, is necessary to make a systematic process that enables organizations or companies anticipate to technological changes. In this context, the design of methodologies based on the Technology Watch (TW) allows managing the innovative activity of organizations or companies facilitating the process of generating ideas for products or services development. For this reason, in this Thesis a strategy for applying Technological Watch methodologies applied to a R&D project studying Natural User Interfaces (NUI) has been designed. To achieve this goal, the starting point was the CETISME project methodologies, which are based on the Technology Watch and the Competitive Intelligence process, clearly identifying each of the phases that compose it: identification of objectives, selection of the information sources, storage, search and analysis of the information, and finally validating the information that concludes with the creation of Technological Watch reports. Therefore, for each of the phases composing what is commonly known as the monitoring cycle, it has been explained in first place what they consist of, what strategies are more adequate as well as how they should be implemented, and finally, if necessary, what tools (from databases to software) are needed or are useful for managing the process and optimize it. Thus, as discussed throughout this document, the application of said methodology will allow organizations or companies to obtain advantageous situations when it comes to innovate, catch opportunities or detect threats, to identify competitors or potential alliances, among others.

Detecting, Localizing and Following Dynamic Objects with a Mini-UAV

This paper presents an approach for the detection, localization and following of dynamic terrestrial objects using a mini-UAV. The development is intended to be used for surveillance of large infrastructures. The detection algorithm is based on finding several pre-defined characteristics of the target, such as color, shape and size. The process used to localize the target, once it is detected, is based on an inversion of the Pinhole camera model. The task of following the Summit XL was designed to keep the target inside the field of view of the camera, and it was implemented in the form of a PID controller. The system has been tested both in simulation and with real robots, showing promising results.

Multi-UAV Coordination and Control Interface

The interest in missions with multiple Unmanned Aerial Vehicles (UAVs) has increased significantly in last years. These missions take advantage of the use of fleets instead of single UAVs to ensure the success, reduce the duration or increase the goals of the mission. In addition, they allow performing tasks that require multiple agents and certain coordination (e.g. surveillance of large areas or transport of heavy loads). Nevertheless, these missions suppose a challenge in terms of control and monitoring. In fact, the workload of the operators rises with the utilization of multiple UAVs and payloads, since they have to analyze more information, make more decisions and generate more commands during the mission. This work addresses the operator workload problem in multi-UAV missions by reducing and selecting the information. Two approaches are considered: a first one that selects the information according to the mission state, and a second one that selects it according to the operator preferences. The result is an interface that is able to control the amount of information and show what is relevant for mission and operator at the time.