Differences in the structural response of 'granny-smith' apples under mechanical impact and compression

Apple fruits, cv. Granny Smith, were subjected to mechanical impact and compression loads utilizing a steel rod with a spherical tip 19 mm diameter, 50.6 g mass. Energies applied were low enough to produce enzymatic reaction: 0.0120 J for impact, and 0.0199 J for compression. Bruised material was cut and examined with a transmission electron microscope. In both compression and impact, bruises showed a central region located in the flesh parenchyma, at a distance that approximately equalled the indentor tip radius. The parenchyma cells of this region were more altered than cells from the epidermis and hypodermis. Tissues under compression presented numerous deformed parenchyma cells with broken tonoplasts and tissue degradation as predicted by several investigators. The impacted cells supported different kinds of stresses than compressed cells, resulting in the formation of intensive vesiculation, either in the vacuole or in the middle lamella region between cell walls of adjacent cells. A large proportion of parenchyma cells completely split or had initiated splitting at the middle lamella. Bruising may develop with or without cell rupture. Therefore, cell wall rupture is not essential for the development of a bruise, at least the smallest one, as predicted previously

Dynamic Response of Wind Turbines to Theoretical 3D Seismic Motions Taking into Account the Rotational Component

We study the dynamic response of a wind turbine structure subjected to theoretical seismic motions, taking into account the rotational component of ground shaking. Models are generated for a shallow moderate crustal earthquake in the Madrid Region (Spain). Synthetic translational and rotational time histories are computed using the Discrete Wavenumber Method, assuming a point source and a horizontal layered earth structure. These are used to analyze the dynamic response of a wind turbine, represented by a simple finite element model. Von Mises stress values at different heights of the tower are used to study the dynamical structural response to a set of synthetic ground motion time histories

Fracture of concrete structural members subjected to blast

If reinforced concrete structures are to be safe under extreme impulsive loadings such as explosions, a broad understanding of the fracture mechanics of concrete under such events is needed. Most buildings and infrastructures which are likely to be subjected to terrorist attacks are borne by a reinforced concrete (RC) structure. Up to some years ago, the traditional method used to study the ability of RC structures to withstand explosions consisted on a choice between handmade calculations, affordable but inaccurate and unreliable, and full scale experimental tests involving explosions, expensive and not available for many civil institutions. In this context, during the last years numerical simulations have arisen as the most effective method to analyze structures under such events. However, for accurate numerical simulations, reliable constitutive models are needed. Assuming that failure of concrete elements subjected to blast is primarily governed by the tensile behavior, a constitutive model has been built that accounts only for failure under tension while it behaves as elastic without failure under compression. Failure under tension is based on the Cohesive Crack Model. Moreover, the constitutive model has been used to simulate the experimental structural response of reinforced concrete slabs subjected to blast. The results of the numerical simulations with the aforementioned constitutive model show its ability of representing accurately the structural response of the RC elements under study. The simplicity of the model, which does not account for failure under compression, as already mentioned, confirms that the ability of reinforced concrete structures to withstand blast loads is primarily governed by tensile strength.

Behaviour of Concrete Structural Members Subjected to Air Blast Loading

Numerical analysis is a suitable tool in the design of complex reinforced concrete structures under extreme impulsive loadings such as impacts or explosions at close range. Such events may be the result of terrorist attacks. Reinforced concrete is commonly used for buildings and infrastructures. For this reason, the ability to accurately run numerical simulations of concrete elements subjected to blast loading is needed. In this context, reliable constitutive models for concrete are of capital importance. In this research numerical simulations using two different constitutive models for concrete (Continuous Surface Cap Model and Brittle Damage Model) have been carried out using LS-DYNA. Two experimental benchmark tests have been taken as reference. The results of the numerical simulations with the aforementioned constitutive models show different abilities to accurately represent the structural response of the reinforced concrete elements studied.

A methodology to calibrate structural finite element models for reinforced concrete structures subject to blast loads

Civil buildings are not specifically designed to support blast loads, but it is important to take into account these potential scenarios because of their catastrophic effects, on persons and structures. A practical way to consider explosions on reinforced concrete structures is necessary. With this objective we propose a methodology to evaluate blast loads on large concrete buildings, using LS-DYNA code for calculation, with Lagrangian finite elements and explicit time integration. The methodology has three steps. First, individual structural elements of the building like columns and slabs are studied, using continuum 3D elements models subjected to blast loads. In these models reinforced concrete is represented with high precision, using advanced material models such as CSCM_CONCRETE model, and segregated rebars constrained within the continuum mesh. Regrettably this approach cannot be used for large structures because of its excessive computational cost. Second, models based on structural elements are developed, using shells and beam elements. In these models concrete is represented using CONCRETE_EC2 model and segregated rebars with offset formulation, being calibrated with continuum elements models from step one to obtain the same structural response: displacement, velocity, acceleration, damage and erosion. Third, models basedon structural elements are used to develop large models of complete buildings. They are used to study the global response of buildings subjected to blast loads and progressive collapse. This article carries out different techniques needed to calibrate properly the models based on structural elements, using shells and beam elements, in order to provide results of sufficient accuracy that can be used with moderate computational cost.

An interactive web-based learning assistant for structural analysis of continuous beams

There are significant levels of concern about the relevance and the difficulty of learning some issues on Strength of Materials and Structural Analysis. Most students of Continuum Mechanics and Structural Analysis in Civil Engineering usually point out some key learning aspects as especially difficult for acquiring specific skills. These key concepts entail comprehension difficulties but ease access and applicability to structural analysis in more advanced subjects. Likewise, some elusive but basic structural concepts, such as flexibility, stiffness or influence lines, are paramount for developing further skills required for advanced structural design: tall buildings, arch-type structures as well as bridges. As new curricular itineraries are currently being implemented, it appears appropriate to devise a repository of interactive web-based applications for training in those basic concepts. That will hopefully train the student to understand the complexity of such concepts, to develop intuitive knowledge on actual structural response and to improve their preparation for exams. In this work, a web-based learning assistant system for influence lines on continuous beams is presented. It consists of a collection of interactive user-friendly applications accessible via Web. It is performed in both Spanish and English languages. Rather than a “black box” system, the procedure involves open interaction with the student, who can simulate and virtually envisage the structural response. Thus, the student is enabled to set the geometric, topologic and mechanic layout of a continuous beam and to change or shift the loading and the support conditions. Simultaneously, the changes in the beam response prompt on the screen, so that the effects of the several issues involved in structural analysis become apparent. The system is performed through a set of web pages which encompasses interactive exercises and problems, written in JavaScript under JQuery and DyGraphs frameworks, given that their efficiency and graphic capabilities are renowned. Students can freely boost their self-study on this subject in order to face their exams more confidently. Besides, this collection is expected to be added to the "Virtual Lab of Continuum Mechanics" of the UPM, launched in 2013 (http://serviciosgate.upm.es/laboratoriosvirtuales/laboratorios/medios-continuos-en-construcci%C3%B3n)

A framework for adaptive e-learning for continuum mechanics and structural analysis

This paper presents a project for providing the students of Structural Engineering with the flexibility to learn outside classroom schedules. The goal is a framework for adaptive E-learning based on a repository of open educational courseware with a set of basic Structural Engineering concepts and fundamentals. These are paramount for students to expand their technical knowledge and skills in structural analysis and design of tall buildings, arch-type structures as well as bridges. Thus, concepts related to structural behaviour such as linearity, compatibility, stiffness and influence lines have traditionally been elusive for students. The objective is to facilitate the student a teachinglearning process to acquire the necessary intuitive knowledge, cognitive skills and the basis for further technological modules and professional development in this area. As a side effect, the system is expected to help the students improve their preparation for exams on the subject. In this project, a web-based open-source system for studying influence lines on continuous beams is presented. It encompasses a collection of interactive user-friendly applications accessible via Web, written in JavaScript under JQuery and Dygraph Libraries, taking advantage of their efficiency and graphic capabilities. It is performed in both Spanish and English languages. The student is enabled to set the geometric, topologic, boundary and mechanic layout of a continuous beam. While changing the loading and the support conditions, the changes in the beam response prompt on the screen, so that the effects of the several issues involved in structural analysis become apparent. This open interaction with the user allows the student to simulate and virtually infer the structural response. Different levels of complexity can be handled, whereas an ongoing help is at hand for any of them. Students can freely boost their experiential learning on this subject at their own pace, in order to further share, process, generalize and apply the relevant essential concepts of Structural Engineering analysis. Besides, this collection is being added to the "Virtual Lab of Continuum Mechanics" of the UPM, launched in 2013 (http://serviciosgate.upm.es/laboratoriosvirtuales/laboratorios/medios-continuos-en-construcci%C3%B3n)

Parametric analysis of gravity offshore structures: Part 1

The objective of this paper is to analyse the influence of the variation of some parameters used in the analysis of the dynamic response of offshore structures under the action of wind generated waves. The structural response has been obtained by stochastic methods using two discretization models. One with lumped parameters, using translational degrees of freedom (d.o.f.) and the other with one-dimensional finite elements. Using each of these methods the problem has been solved with several d.o.f., analysing the influence of the number of d.o.f. on the results.

Análisis de movimientos y aceleraciones provocados por las acciones del oleaje y de los buques en el dique de Botafoc (Ibiza)

El reciente desarrollo de la instrumentación diseñada para proporcionar datos de aceleraciones y movimientos del cajón número 8 del dique Botafoc (Ibiza), perteneciente a la Autoridad Portuaria de Baleares (Puertos del Estado), en conjunción con datos procedentes de una instrumentación compuesta por sensores de presión existente en el paramento vertical, proporciona un novedoso medio para analizar la respuesta estructural del cajón, no sólo ante la acción del oleaje, sino también ante los efectos producidos por las maniobras de los buques en el muelle. Como la medición de estas aceleraciones y velocidades angulares se hace a altas frecuencias (de hasta 400 Hz), podemos proporcionar datos válidos acerca del comportamiento estructural y de los movimientos reales del cajón, tratando de correlacionar este comportamiento con los resultados obtenidos por el grupo de trabajo PROVERBS (Probabilistic design of vertical breakwaters, MAST III EU Programme), y generando una base de datos estadística de movimientos que deben considerarse para enriquecer los conocimientos en este ámbito. Además, la posibilidad de registrar los efectos causados por las maniobras de atraquedesatraque-estancia de los buques, abre un nuevo punto de vista al diseño estructural de un dique-muelle, siendo también de gran interés para los diseñadores de obras marítimas y para la correcta definición de las maniobras del buque en el muelle. The recent deployment of new instrumentation designed to provide accelerations and angular velocities from caisson #8 at Botafoc seawall, Ibiza, along with an existing pressure sensor instrumentation at the vertical wall, provides a way to record and process data of the structural response, not only to waves, but also to effects caused by ship mooring operations at Botafoc seawall. As the measurement of these angular speeds and accelerations is programmed with sampling frecuencies up to 400 Hz, and by integrating all data through time we may provide suitable data of the structural behaviour of the caisson. This behaviour is tried to be correlated with the PROVERBS working group achievements (Probabilistic design of vertical breakwaters, MAST III EU Programme), generating a statistical movement database that must be used to improve knowledge on this subject. Also the possibility to record the effects caused by the different ship mooring operations is a new point of view of the complete structural design of a seawall-wharf, which is considered an interesting matter for coastal designers as well for a correct ship mooring processes definition.

On soil-structure interaction in large non-slender partially buried structures

This paper addresses the seismic analysis of a deeply embedded non-slender structure hosting the pumping unit of a reservoir. The dynamic response in this type of problems is usually studied under the assumption of a perfectly rigid structure using a sub-structuring procedure (three-step solution) proposed specifically for this hypothesis. Such an approach enables a relatively simple assessment of the importance of some key factors influencing the structural response. In this work, the problem is also solved in a single step using a direct approach in which the structure and surrounding soil are modelled as a coupled system with its actual geometry and flexibility. Results indicate that, quite surprisingly, there are significant differences among prediction using both methods. Furthermore, neglecting the flexibility of the structure leads to a significant underestimation of the spectral accelerations at certain points of the structure.

A simplified model for evaluation of fatigue damage in frames

Many studies have been developed to analyze the structural seismic behavior through the damage index concept. The evaluation of this index has been employed to quantify the safety of new and existing structures and, also, to establish a framework for seismic retrofitting decision making of structures. Most proposed models are based in a posterthquake evaluation in such a way they uncouple the structural response from the damage evaluation. In this paper, a generalization of the model by Flórez-López (1995) is proposed. The formulation employs irreversible thermodynamics and internal state variable theory applied to the study of beams and frames and it allows and explicit coupling between the degradation and the structural mechanical behavior. A damage index es defined in order to model elastoplasticity coupled with damage and fatigue damage.

Imposed Deformations Measured on a Real Integral Structure: New Airport Terminal Barajas, Madrid, Spain

Experimental research on imposed deformation is generally conducted on small scale laboratory experiments. The attractiveness of field research lies in the possibility to compare results obtained from full scale structures to theoretical prediction. Unfortunately, measurements obtained from real structures are rarely described in literature. The structural response of integral edifices depends significantly on stiffness changes and constraints. The New Airport Terminal Barajas in Madrid, Spain provides with large integral modules, partially post?tensioned concrete frames, cast monolithically over three floor levels and an overall length of approx. 80 m. The field campaign described in this article explains the instrumentation of one of these frames focusing on the influence of imposed deformations such as creep, shrinkage and temperature. The applied monitoring equipment included embedded strain gages, thermocouples, DEMEC measurements and simple displacement measurements. Data was collected throughout construction and during two years of service. A complete data range of five years is presented and analysed. The results are compared with a simple approach to predict the long?term shortening of this concrete structure. Both analytical and experimental results are discussed.

Computational model for local damage assesment of structures

In the last years many studies have been developed to analyze the seismic behavior throug the damage concept. In fact, the evaluation of the structural damage is important in order to quantify the safety of new and existing structures and, also, to establish a framework for seismic retrofitting decision making of structures. Most proposed models are based on a post-earthquake evaluation in such a way they uncouple the computation of the structural response from that of damage. However, there are other models which include explicity the existing coupling between the degradation and the structural mechanical beaviour. Those models are closer to the physical reality and its formulation is based on the principles of Continuum Damage Mechanics. In the present work, a coupled model is formulated using a simplified application of the Continuum Damage Mechanics to the analysis of frames and allows its representation in standard finite element programs. This work is part of the activities developed by the Structural Mechanics Department (UPM) within ICONS (European Research Project on Innovative Seismic Design Concepts for New and Existing Structures).

Inestabilidad de pórticos planos metálicos de edificación con inclusión de la flexibilidad de las uniones y elementos no prismáticos : un enfoque para la optimización

En esta tesis se aborda el problema de la modelización, análisis y optimización de pórticos metálicos planos de edificación frente a los estados límites último y de servicio. El objetivo general es presentar una técnica secuencial ordenada de optimización discreta para obtener el coste mínimo de pórticos metálicos planos de edificación, teniendo en cuenta las especificaciones del EC-3, incorporando las uniones semirrígidas y elementos no prismáticos en el proceso de diseño. Asimismo se persigue valorar su grado de influencia sobre el diseño final. El horizonte es extraer conclusiones prácticas que puedan ser de utilidad y aplicación simple para el proyecto de estructuras metálicas. La cantidad de publicaciones técnicas y científicas sobre la respuesta estructural de entramados metálicos es inmensa; por ello se ha hecho un esfuerzo intenso en recopilar el estado actual del conocimiento, sobre las líneas y necesidades actuales de investigación. Se ha recabado información sobre los métodos modernos de cálculo y diseño, sobre los factores que influyen sobre la respuesta estructural, sobre técnicas de modelización y de optimización, al amparo de las indicaciones que algunas normativas actuales ofrecen sobre el tema. En esta tesis se ha desarrollado un procedimiento de modelización apoyado en el método de los elementos finitos implementado en el entorno MatLab; se han incluido aspectos claves tales como el comportamiento de segundo orden, la comprobación ante inestabilidad y la búsqueda del óptimo del coste de la estructura frente a estados límites, teniendo en cuenta las especificaciones del EC-3. También se ha modelizado la flexibilidad de las uniones y se ha analizado su influencia en la respuesta de la estructura y en el peso y coste final de la misma. Se han ejecutado algunos ejemplos de aplicación y se ha contrastado la validez del modelo con resultados de algunas estructuras ya analizadas en referencias técnicas conocidas. Se han extraído conclusiones sobre el proceso de modelización y de análisis, sobre la repercusión de la flexibilidad de las uniones en la respuesta de la estructura. El propósito es extraer conclusiones útiles para la etapa de proyecto. Una de las principales aportaciones del trabajo en su enfoque de optimización es la incorporación de una formulación de elementos no prismáticos con uniones semirrígidas en sus extremos. Se ha deducido una matriz de rigidez elástica para dichos elementos. Se ha comprobado su validez para abordar el análisis no lineal; para ello se han comparado los resultados con otros obtenidos tras aplicar otra matriz deducida analíticamente existente en la literatura y también mediante el software comercial SAP2000. Otra de las aportaciones de esta tesis es el desarrollo de un método de optimización del coste de pórticos metálicos planos de edificación en el que se tienen en cuenta aspectos tales como las imperfecciones, la posibilidad de incorporar elementos no prismáticos y la caracterización de las uniones semirrígidas, valorando la influencia de su flexibilidad sobre la respuesta de la estructura. Así, se han realizado estudios paramétricos para valorar la sensibilidad y estabilidad de las soluciones obtenidas, así como rangos de validez de las conclusiones obtenidas. This thesis deals with the problems of modelling, analysis and optimization of plane steel frames with regard to ultimate and serviceability limit states. The objective of this work is to present an organized sequential technique of discrete optimization for achieving the minimum cost of plane steel frames, taking into consideration the EC-3 specifications as well as including effects of the semi-rigid joints and non-prismatic elements in the design process. Likewise, an estimate of their influence on the final design is an aim of this work. The final objective is to draw practical conclusions which can be handful and easily applicable for a steel-structure project. An enormous amount of technical and scientific publications regarding steel frames is currently available, thus making the achievement of a comprehensive and updated knowledge a considerably hard task. In this work, a large variety of information has been gathered and classified, especially that related to current research lines and needs. Thus, the literature collected encompasses references related to state-of-the-art design methods, factors influencing the structural response, modelling and optimization techniques, as well as calculation and updated guidelines of some steel Design Codes about the subject. In this work a modelling procedure based on the finite element implemented within the MatLab programming environment has been performed. Several keys aspects have been included, such as second order behaviour, the safety assessment against structural instability and the search for an optimal cost considering the limit states according to EC-3 specifications. The flexibility of joints has been taken into account in the procedure hereby presented; its effects on the structural response, on the optimum weight and on the final cost have also been analysed. In order to confirm the validity and adequacy of this procedure, some application examples have been carried out. The results obtained were compared with those available from other authors. Several conclusions about the procedure that comprises modelling, analysis and design stages, as well as the effect of the flexibility of connections on the structural response have been drawn. The purpose is to point out some guidelines for the early stages of a project. One of the contributions of this thesis is an attempt for optimizing plane steel frames in which both non-prismatic beam-column-type elements and semi-rigid connections have been considered. Thus, an elastic stiffness matrix has been derived. Its validity has been tested through comparing its accuracy with other analytically-obtained matrices available in the literature, and with results obtained by the commercial software SAP2000. Another achievement of this work is the development of a method for cost optimization of plane steel building frames in which some relevant aspects have been taken in consideration. These encompass geometric imperfections, non-prismatic beam elements and the numerical characterization of semi-rigid connections, evaluating the effect of its flexibility on the structural response. Hence, some parametric analyses have been performed in order to assess the sensitivity, the stability of the outcomes and their range of applicability as well.

Mejora de los modelos térmicos de las presas bóveda en explotación : aplicación al análisis del efecto del cambio climático

Las cargas de origen térmico causadas por las acciones medioambientales generan esfuerzos apreciables en estructuras hiperestáticas masivas, como es el caso de las presas bóvedas. Ciertas investigaciones apuntan que la variación de la temperatura ambiental es la segunda causa de reparaciones en las presas del hormigón en servicio. Del mismo modo, es una causa de fisuración en un porcentaje apreciable de casos. Las presas son infraestructuras singulares por sus dimensiones, su vida útil, su impacto sobre el territorio y por el riesgo que implica su presencia. La evaluación de ese riesgo requiere, entre otras herramientas, de modelos matemáticos de predicción del comportamiento. Los modelos han de reproducir la realidad del modo más fidedigno posible. Además, en un escenario de posible cambio climático en el que se prevé un aumento de las temperaturas medias, la sociedad ha de conocer cuál será el comportamiento estructural de las infraestructuras sensibles en los futuros escenarios climáticos. No obstante, existen escasos estudios enfocados a determinar el campo de temperaturas de las presas de hormigón. Así, en esta investigación se han mejorado los modelos de cálculo térmico existentes con la incorporación de nuevos fenómenos físicos de transferencia de calor entre la estructura y el medio ambiente que la rodea. También se han propuesto nuevas metodologías más eficientes para cuantificar otros mecanismos de transferencia de calor. La nueva metodología se ha aplicado a un caso de estudio donde se disponía de un amplio registro de temperaturas de su hormigón. Se ha comprobado la calidad de las predicciones realizadas por los diversos modelos térmicos en el caso piloto. También se han comparado los resultados de los diversos modelos entre sí. Finalmente, se ha determinado las consecuencias de las predicciones de las temperaturas por algunos de los modelos térmicos sobre la respuesta estructural del caso de estudio. Los modelos térmicos se han empleado para caracterizar térmicamente las presas bóveda. Se ha estudiado el efecto de ciertas variables atmosféricas y determinados aspectos geométricos de las presas sobre su respuesta térmica. También se ha propuesto una metodología para evaluar la respuesta térmica y estructural de las infraestructuras frente a los posibles cambios meteorológicos inducidos por el cambio climático. La metodología se ha aplicado a un caso de estudio, una presa bóveda, y se ha obtenido su futura respuesta térmica y estructural frente a diversos escenarios climáticos. Frente a este posible cambio de las variables meteorológicas, se han detallado diversas medidas de adaptación y se ha propuesto una modificación de la normativa española de proyecto de presas en el punto acerca del cálculo de la distribución de temperaturas de diseño. Finalmente, se han extraído una serie de conclusiones y se han sugerido posibles futuras líneas de investigación para ampliar el conocimiento del fenómeno de la distribución de temperaturas en el interior de las presas y las consecuencias sobre su respuesta estructural. También se han propuesto futuras investigaciones para desarrollar nuevos procedimiento para definir las cargas térmicas de diseño, así como posibles medidas de adaptación frente al cambio climático. Thermal loads produced by external temperature variations may cause stresses in massive hyperstatic structures, such as arch dams. External temperature changes are pointed out as the second most major repairs in dams during operation. Moreover, cracking is caused by thermal loads in a quite number of cases. Dams are unique infrastructures given their dimensions, lifetime, spatial impacts and the risks involve by their presence. The risks are assessed by means of mathematical models which compute the behavior of the structure. The behavior has to be reproduced as reliable as possible. Moreover, since mean temperature on Earth is expected to increase, society has to know the structural behavior of sensitive structures to climate change. However, few studies have addressed the assessment of the thermal field in concrete dams. Thermal models are improved in this research. New heat transfer phenomena have been accounted for. Moreover, new and more efficient methodologies for computing other heat transfer phenomena have been proposed. The methodology has been applied to a case study where observations from thermometers embedded in the concrete were available. Recorded data were predicted by several thermal models and the quality of the predictions was assessed. Furthermore, predictions were compared between them. Finally, the consequences on the stress calculations were analyzed. Thermal models have been used to characterize arch dams from a thermal point of view. The effect of some meteorological and geometrical variables on the thermal response of the dam has been analyzed. Moreover, a methodology for assessing the impacts of global warming on the thermal and structural behavior of infrastructures has been proposed. The methodology was applied to a case study, an arch dam, and its thermal and structural response to several future climatic scenarios was computed. In addition, several adaptation strategies has been outlined and a new formulation for computing design thermal loads in concrete dams has been proposed. Finally, some conclusions have been reported and some future research works have been outlined. Future research works will increase the knowledge of the concrete thermal field and its consequences on the structural response of the infrastructures. Moreover, research works will develope a new procedure for computing the design thermal loads and will study some adaptation strategies against the climate change.